Search Documents

By D. F. Cooper, J. G. Paterson, K. H. Pang

"Effective control of metallurgy by manual adjustment of cell levels is common flotation practice. With an on-stream XRF analyzer interfaced to a process control computer it is possible to program the computer to carry out this function automatically. This paper describes the development and implementation of closed loop control of the concentrate and tailing grades at the Clarabelle Mill of the International Nickel Company of Canada, Limited, The XRF analyzer was used as the sensor, cell level as the control and the computer as the controller.IntroductionThe International Nickel Company of Canada, Limited recently brought on-stream Clarabelle Mill having a rated capacity of 35,000 tons per day. The plant was required to increase milling capacity in the Sudbury area by 9,000 tons per day and to improve milling efficiencies by replacing the obsolete crushing and grinding equipment at the Copper Cliff Mill. This represents the fourth mill built since 1959 and incorporates the latest thinking in a continuing evolution of instrumentation and control concepts. Table 1 illustrates control progress at Inco since 1959.In 1967 Frood-Stobie Mill came on-stream incorporating a central control room, an on-stream analyzer, a data gathering computer, and a significant change in instrumentation from direct-contacted pneumatic to miniature electronic. The computer successfully controls the analyzer but has very limited process control capability. Based on this experience a process control computer system was installed at Clarabelle Mill with the objective of carrying out extensive supervisory control and a limited amount of direct digital control."

Jan 1, 1973

By Kim Wiwchar, Elizabeth Mbaja, Lynne Dang, Jim Furey, Anita Marks

"Suncor Energy Inc., located north of Fort McMurray, Alberta, commenced pilot scale operation using a CPT 4’ diameter flotation column in March 2003. This larger scale trial follows two previously successful flotation column bench scale tests. They included an April 2002 trial with a 2.4” inner diameter column from the University of Alberta and a 20” diameter CPT column in August 2002. The column receives middlings stream feed from one of Suncor’s deep cone separation cells and is operated in parallel with a set of WEMCO flotation cells. The recovery, tails losses, and concentrate quality are being compared between the two systems. The column, to date, has been tested with all types of run of mine ore grades. Variables such as wash water flow and temperature, sparger nozzle size and location, sparger air/water flow rates, and column residence time has been adjusted to achieve better recovery and final product quality.Used in many mineral processing applications, column flotation is primarily used for the final stage of sulphide cleaning and flotation of phosphate or iron ore. As well, mechanical cells are often used in combination with a column to retrofit an operation and to produce a cleaner product.Initial results prove that this is the first successful application of a flotation column in an oilsand application. If viable, it will be an inexpensive process for recovery of bitumen from a middlings stream and able to produce a final product suitable for froth treatment.INTRODUCTIONSuncor’s oilsand is surface mined from the Athabasca Oilsand deposit north of Fort McMurray, Alberta. The oilsand is then mixed with hot process water (HPW) and the bitumen is slurried in a pipeline. Large separation cells as shown in Figure 1 float off the bitumen product, which is then steam or static deaerated and sent to Secondary Extraction for further cleaning. The tails stream from the cell is sent to the Final Tails Pumphouse (FTPH) for processing. The tailings flotation froth product gets recycled to the separation cell oilsand feed. The tailings are pumped from the FTPH to tailings ponds. The middlings stream is drawn off the separation cell approximately 9’ from the froth overflow level. It runs down, by gravity, to the scavenger banks for bitumen recovery. It was from this stream off of the Line 6 Separation Cell that the feed to the Canadian Process Technologies Inc (CPT) flotation column was taken."

Jan 1, 2004

By K. G. Thorne, M. J. McLeod, D. Hoy

"Throughout the Paleozoic, a variety of gold depositional environments were created in the New Brunswick segment of the northern Appalachians because of the complexity of arc and continental plate collisions and subsequent erosion of the orogen. In southwestern New Brunswick, recent exploration and research has focused on deposits and occurrences that can be broadly classified as intrusion-related, generated by late- to post-orogenic felsic to intermediate plutonic rocks emplaced during the Early to Middle Devonian. This work has led to the establishment of models for gold mineralization and guidelines for exploration in this area, which might also be applicable elsewhere in the southern part of the province and, perhaps, throughout the northern Appalachians. The deposits in the vicinity of Clarence Stream in southwestern New Brunswick exemplify this deposit type, and highlight the emergence of a possible major gold district in the region. Durant le Paléozoïque, une grande variété d’environnements aurifères ont été créés dans le segment néo-brunswickois des Appalaches du nord en raison de la complexité des collisions entre arcs et plaques continentales ainsi que durant l’érosion subséquente de l’orogène. Dans le sud-ouest du Nouveau Brunswick, les travaux d’exploration et de recherche récents se sont tournés vers les gisements et les indices appartenant à la classe des gîtes associés aux intrusions, générés par des roches plutoniques felsiques à intermédiaires tardi- à post-orogéniques mises en place au Dévonien précoce à moyen. Ces travaux ont permis d’établir des modèles de mise en place pour la minéralisation aurifère ainsi que des guides d’exploration pour ce secteur, lesquels pourraient aussi être appliqués ailleurs dans le sud de la province et, possiblement, dans l’ensemble des Appalaches du nord. Les gîtes aux environs de Clarence Stream dans le sud-ouest du Nouveau Brunswick sont un exemple de ce type de gisement, mettant en valeur ce qui pourrait devenir un district aurifère majeur dans la région."

Jan 1, 2008

By R. Jackman, D. Koningen, G. Wilcox

"Gowest Gold Ltd. is in the process of developing the Frankfield East gold deposit located along the largely undeveloped Pipestone fault northeast of Timmins, Ontario. In addition to resource development and environmental permitting work the company has had an ongoing program of metallurgical and engineering studies aimed at evaluating options for processing the Frankfield East ore. Mineralization at the Frankfield project contains arsenopyrite and pyrite as the major sulphide minerals. Bulk flotation of all sulphides results in extremely high gold recovery. However, the gold is almost entirely associated with the arsenopyrite fraction of the ore and is refractory in nature requiring preoxidation treatment. Selective flotation was investigated to recover a gold-arsenopyrite concentrate thereby reducing the mass which would be subjected to further gold processing. As part of this work, a pyrite concentrate low in arsenic content was also recovered that would be suitable as a source of sulphur for a smelter (or other pyrometallurgical facility). Production of separate arsenopyrite and pyrite concentrates is frequently examined but rarely adopted due to the distribution of gold between the two products or the inability to achieve adequate separation. Several flowsheet options were investigated in the study. The best results were achieved following a sequential flotation flowsheet. The flowsheet configuration was key to meeting the targets for the two products. In this paper, the various options investigated are reviewed and the results of the final flowsheet are presented. The overall plan by Gowest was to evaluate all process options to bring the Frankfield East deposit into production. The ability to effectively separate the arsenopyrite and pyrite components in the ore provides Gowest with added opportunities to pursue both short and long term production scenarios."

Jan 1, 2012

By S. V. Burr

"A 28-year study of cross folds leads to the conclusion that the northwest-southeast folds recognized in many areas of North America are part of a regional pattern. Detailed examination of over 650 geological maps and reports of Ontario indicates that this folding can be traced across the province. Evidence is presented that this fold pattern played an important part in determining the pattern and scale of intrusion, that its recognition in the field can aid in defining stratigraphy, folding and faulting, and that it may have played an important role in channeling hydrothermal or magmatic mineralization. IntroductionThe concept of regional cross folding in Ontario is not new. W.H. Gross (1955) discussed regional cross folds in the Archean of Northwestern Ontario, and A.M. Goodwin (1961) referred to regional cross folds in the Archean of Ontario and Quebec. However, the interpretation in this paper is new.The writer saw a cross fold for the first time, underground, at Little Long Lac Gold Mines in Geraldton, Ontario, in 1951. This recalled the ""transverse folds"" on E.R. Faribault's classical maps of Nova Scotia, published by the Geological Survey around the turn of the century; M.E. Hurst's cross fold(s) at Timmins, Ontario (Figure I); and the cross folds mapped by A.W. Jolliffe in the Yellowknife area of the Northwest Territories. All these mapped cross folds had one thing in common with the fold at Little Long Lac: A northwest-southeast axial trend. Were such cross folds of purely local extent, or might they be indicative of a widespread regional fold pattern? If so, has such folding any significance for mineral exploration or potential?By 1959, based on a study of about 1000 Canadian geological maps and reports, including 291 in Ontario, the writer reached the conclusion that cross folding trending northwest-southeast is so widespread as to constitute a pattern of folding, and that such cross folding should produce changes in plunge along pre-existing greenstone fold belts."

Jan 1, 1980

By G. E. Agar, W. B. Kipkie, V. K. Drylie

"This paper describes mineral processing test work on drill core samples from an ilmenite deposit in Terrebonne County just north of Montreal.Mineralogical examination showed that the intimate associa¬tion between ilmenite and hematite precluded their separation. The maximum concentrate grade was therefore limited to 22.9% Ti. Liberation of gangue from the hemo-ilmenite grains occurred around 400 µm, a size which proved to be too coarse for recovery by flotation.Other physical separation techniques, such as elec¬trodynamic, magnetic and jigging, were tried in order to take advantage of the relatively coarse liberation size. An all-flotation procedure and a combination of jigging and flotation yielded similar separations.IntroductionInco Metals Company, through its subsidiary Canico, optioned an ilmenite deposit in Terrebonne County, just north of Montreal, and conducted a drilling campaign to confirm previous geological assessments of the deposit and to provide core samples for mineralogical study. Parts of these core samples were used for mineral processing studies, which will be described in this report. The objective was to identify suitable upgrading procedures, to determine the optimum combination of concentrate grade and recovery, and to provide suitable batches of concentrate for further treatment."

Jan 1, 1980

By Bernard Jones

LTUG ? A meeting of many mining companies that are using large tires ? Introduction of the mines and size ? Companies go over their usage of tires and performance ? As a group we discuss how the manufactures are doing with supplies and performance (who's running what sizes and manufactures they are using) ? The mine's best practices they use (which ones work for them and which ones don't) ? Where the mines see themselves going in the future ? What type of tire management the mines have in place

May 1, 2009

By S. G. Shabestari, S. Saeidinia, P. Mokarian

"The experiments were conducted to investigate the influence of various process parameters in rotary degassing of aluminum alloy AS5U3G. Degassing was carried out by use of argon inert gas. The flow rate of the gas was investigated in the range of 12 to 21 L/min., 350 to 500 rpm rotor speed, 6 to 12 minutes degassing time, and 755°C to 780°C melt temperature. Degassing efficiency was evaluated through measuring the density of RPT samples. By optimizing the process parameters, RPT sample density was increased up to 2.73 g/cm3, which guaranties the production of high-quality aluminum castings. Tensile strength and elongation were increased considerably by degassing process. Scanning electron microscopy (SEM) shows small size and well-distributed microporosity. IntroductionOne of the major problems associated with the casting of aluminum alloys is the formation of gas porosity. Aluminum and its alloys are very susceptible to hydrogen absorption. Because solubility is much lower in solid state than liquid state, hydrogen atoms leave their position during solidification and combine together to form hydrogen molecules. These micrometer- scale cavities, called microporosity, cause the reduction of mechanical properties, particularly strength, ductility, fracture toughness, fatigue resistance, pressure tightness, and corrosion resistance (Laslaz, 1991; Jorstad and Rasmussen, 1993; Sigworth and Wang, 1994; Korasani, 1996; Anson and Gruzleski, 1999; Zhang et al., 2000). To avoid these problems and produce good quality castings, it is necessary to remove hydrogen from the melt. Several methods are available for degassing aluminum melt. One of them is a rotary degassing system using inert gas, e.g. Ar or N2. Various thermodynamic and kinetic factors govern the removal of hydrogen from molten aluminum (Anderson, 1987; Sigworth, 1987; Pignault, 1993; King and Reynolds, 1995). These are some parameters that affect degassing efficiency. Some of them are discussed here and some are examined in this project."

Jan 1, 2004

"The Dumont deposit is a large (1066 Mt probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the deposit through pre-feasibility. And updated, revised pre-feasibility was released in July 2012.The disseminated nickel sulphide and alloy mineralization is hosted within the serpentinized dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinized, ultramafic sill of komatitic affinity. Pentlandite, heazlewoodite and awaruite are the dominant nickel-bearing, metallic phases and can be recovered by conventional methods (flotation, mag separation). Non-recoverable nickel is also present within the silicate matrix of the serpentinized dunite and is locked in serpentine (Fe and Mg-rich variants) and minor olivine.A detailed mineralogical program including 1097 QEMSCAN® samples and 4300 electron microprobe points were undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. Eighty-three (83) metallurgical tests performed under a standard procedure have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block by block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance thus, unlocking the value of the Dumont deposit and other large tonnage low grade ultramafic nickel deposits."

Jan 1, 2013

By Rodolfo Zanella

Au/TiO2 catalysts prepared by deposition-precipitation with NaOH (DPN) (~3 wt%) and urea (DPU) (~8 wt%) were tested in crotonaldehyde hydrogenation at atmospheric pressure. There is no differences in activity (mole.gAu -1 s-1) and selectivity between both DPU and DPN samples for a given activation treatment. This is due to the fact that DPU and DPN samples exhibit similar gold particle size distribution, although the gold loading in DPU is much higher that in DPN. The DPU samples were reduced under H2 at different temperatures (120-500 °C) or under air at 300 °C with various flow rates, to vary the average particle size within a large range, 1.7 to 8.7 nm. The selectivity to crotyl alcohol (selective hydrogenation of the carbonyl bond) is high, 60-70 %, and almost constant as a function of the particle size. The selectivity to crotyl alcohol is also constant for conversions between 10 and 50%. These results suggest that the adsorption mode of crotonaldehyde is of ?3 or ?4-type. In contrast, the TOF depends on the gold particle size, it drastically increases when the gold particle size is ~2 nm. Our results are in agreement with former studies that suggest that the gold atoms involved in the hydrogenation process are those of low coordination.

Oct 1, 2003

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By R. M. S. Häggblad

The article deals with stabilisation and regeneration of Ce02 and Ce02/Zr02 based Pt water gas shift catalysts, subject to high initial deactivation. The reaction gas species effect on the catalyst deactivation was investigated by H2-TPR. Activity measurements enabled the effect of different promoters, some added to the Ce02 based catalysts and some to the Ce02/Zr02 based Pt catalysts, to be investigated. The catalysts were also characterised by BET and CO-TPR. Deactivated catalysts activity was restored by using various regeneration methods. Of the two selected carriers the Ce02/Zr02 based Pt catalyst showed the highest resilience to deactivation. For the two different carriers, Ce02 and Ce02/Zr02, Wand Re were the best promoters when the catalyst was subject to deactivation. Experiments with Hr TPR indicate a fast initial change in the platinum oxides concentration and composition. The CO-TPR was used to make conclusions about the various regeneration effects of water and oxygen on the catalyst. Finally it is suggested that not one deactivation mechanism is possible and which mechanism that dominates is dependant on the catalyst and the reaction gas composition.

Jan 1, 2005

By C. Stapel, AA Groningen, R. J. De Meijer

"In recent years the Environmental Research Group of the KVI has been developing a number of radiometric techniques that may be employed in mineral sand exploration. These techniques involve: radiometric fingerprinting for assessing sand provenances and mineralogical composition; thermoluminescence for dating and provenance determination of sediments; a towed seabed detector to map seafloors for radiogenic heavy minerals and assessing heavy mineral volumes; and simplified transport mechanism models to explain and predict heavy mineral concentrations.All techniques exploit the property that heavy minerals as a group contain concentrations of naturally occurring uranium and thorium that are a hundred to a thousand times higher than in light minerals. In this paper the physics of a number of methods will be described together with a number of results. Based on these results potential applications to mineral exploration and mining are discussed."

Jan 1, 1994

By R. W. Pugh, D. G. Bellow

"This paper will describe how cultivator shanks are made in one company and how the manufacturing was studied with a view to increasing product consistency and reducing manufacturing cost. The product: which is used extensively in the agriculture industry, was analyzed to determine which geometric parameters optimized its design and whether there was justification for the great variety of styles and shapes that are available in the market. Finally, an extensive series of field trials were undertaken which showed that it is advantageous to the manufacturer to be better aware of the loads and forces that his product is subjected to by another industry.IntroductionStelco maintains a Research Group for its Western Region operations headquartered in Edmonton, Alberta. Because of the small staff, a location that is isolated with respect to its Burlington, Ontario centre and a diverse set of processes and products, a university relationship has developed which may be different from that which would be developed at a larger integrated Steel Works. This paper outlines the type of cooperative studies carried out by Stelco Inc. in Edmonton and the University of Alberta. .To meet the research needs covering a wide variety of steelmaking processes and steel products produced in Edmonton would require more staff and equipment than the sales volume in the West justifies. The gap is filled by cooperation with university personnel. This cooperation has provided these benefits to Stelco Inc.:• access to specialized test equipment and a trained staff to operate it; and• assistance from experts in the areas of product testing and problem solving.Moreover, the close proximity of the university to the plant allows frequent meetings and ensures that practical solutions are developed and implemented. A good example of the ongoing university I industry relationship developed is the joint work on improving cultivator shanks."

Jan 1, 1982

By R. Ramírez, N. Aslin, G. Ríos, T. Bravo, A. R. Almansa

Lacy copper has been an on-going concern at Atlantic Copper for at least 10 years and was first reported to Glencore Technology in mid-2010. Over the past 12 years, many of the plates were replaced due to age and general deterioration however; plate passivation and lacy copper issues have persisted. After analyzing all the possible causes of this phenomena, it was found that the problem is caused by a degradation of stainless steel as a consequence of the deposition of Sb oxides. These deposits act as passivating agents of stainless steel, which reduces the density of copper nuclei, causing defective copper deposit, with low thickness and ductility. After doing several tests for reducing/removing the phenomena, the over-riding factor was found to be the anode-cathode overlap. An adequate overlap eliminates the problem of "lacy copper". This was verified during an eight month trial with anodes extended 2.5cm in length. Longer anode not only avoids the appearance of lacy copper, but also recovers cathodes that already have lacy copper. On the other hand polishing of plates only gives rise to a temporary solution that requires on-going polishing, to avoid the re-appearance of lacy copper. INTRODUCTION The electrolytic copper refinery of Atlantic Copper in Huelva (Spain) was commissioned in 1970 with an initial capacity of 40,000 t of cathodes per year. In 1975 the copper refinery was expanded to 108,000 t/year. From 1994 to 1996, a new expansion together with the implementation of ISA permanent cathode technology led to a capacity of 215,000 t/y. Since 1995, a progressive increase in the current density up to 350 A/m2 has been accomplished, which together with an increase in the number of cells from 1,120 to 1,204, has led to the present cathode production capacity of 290,000 t/y A lack of copper deposition in the lower part of the steel permanent cathodes was first reported in 2010. This phenomenon is known as “Lacy copper” because of the appearance of the copper deposit as it can be seen in Figure 1. The occurrence of this phenomena was relatively low and was assumed to be originated by an excessive anode scrapping. Nevertheless, in December 2015 Lacy Copper was observed in a significant amount of copper cathodes giving rise to the following issues: Increased tramp copper – housekeeping and maintenance problems Poor appearance of cathode deposit and untidy looking bundles

Jan 1, 2019

By D. M. May

"Cut-and-fill mining is a stoping method that has been widely utilized in the mining industry over the past forty years. It took preference over shrinkage methods at Levack in the early 1930sbecause of its safety aspects; i.e., prompt support of the stope sidewalls, good working floors and better accessibility to support poor back areas. In addition, higher recoveries of ore were possible because of the flexibility of the method in that silling could take place easily at any horizon; low-grade ore could be sorted and left in the stope as fill and certain zones of rock could be left unmined. With modern techniques, a steady production rate can be established, as filling and mining can be carried out stimultaneously.AIthough there are numerous variations of cut-and-fill mining throughout the world, this paper reviews the original type of mining, with modifications and improvements through the years to present modern practices, with the Levack West operation appearing to be the most productive at this time. Stoping efficiencies have also increased substantially from the original 10 tons per manshift to the present 55 tons per manshift.The paper also outlines the many improvements that have been made with respect to mucking and ground support operations; from hand mucking in a single stope to the use of frontend loaders and haulage trucks in fully accessible stope complexes; and from timber props to roof bolts of various types. Although present methods are extremely satisfactory, experimentation is continually being conducted to improve safety and productivity for future mining.IntroductionThe major mining operations of the Ontario Division of Inco Limited are located in the Sudbury Basin (Fig. 1). Around the rim of this geological formation and within 30 miles of the City of Sudbury are nine producing mines and one ' open pit operated by the company .Ore production currently approximates 11.5 million tons per annum from underground and open-pit operations. Underground mining methods include sub-level caving, shrinkage, cut and fill, undercut and fill, blasthole and vertical retreat. The Levack Complex, the main plant of which is the central Levack Mine, produces 11,000 tons per day.The first prospecting in the Levack area, in 1887, was conducted by James Stobie, who examined rock cuts along the route of the Canadian Pacific Railway to the northwest of Sudbury. However, it wasn't until 1913 that operations commenced at Levack under the Mond Nickel Company."

Jan 1, 1981

By M. Neven, R. A. Steane, E. Lam

"The Key Lake uranium mill is located in Northern Saskatchewan. It treats a high grade, complex uranium and metal sulphide ore. The plant and process are in many respects unique, because commercial treatment of this type of uranium ore had never been done before. The process and engineering design was based on extensive laboratory test results. A pilot plant testing stage was omitted because of confidence in the test results and time constraints to bring the plant into production.The bench scale testwork on exploration drill core samples along with preparation of the feasibility study and environmental impact statement were carried out between 1976 and 1979. The contract for detailed engineering was awarded to Wright Engineers of Vancouver in late 1980 and in August of 1981 following a public inquiry, approval to proceed with construction was granted.Construction began immediately, and during the winter the foundations for many of the plant buildings were poured and by the beginning of the following winter the buildings had been erected and installation of equipment began. Despite a six month construction worker strike in 1982, the crushing plant started up in June of 1983 and ore processing commenced in October of that year, approximately 3 months behind the original schedule.This paper describes the mill design and compares the expected performance, with the operating experience. Emphasis is directed towards flowsheet and equipment changes made since start-up, operational difficulties encountered and further improvements envisaged. Auxiliary systems are only discussed where they directly affect mill operation."

Jan 1, 1986

By T. Mulja, Michel Boily, Anthony E. Williams-Jones, Pierre Pilote

"The Preissac-Lacorne batholith is composed of suites of early metaluminous calc-alkalic gabbroic to granodioritic intrusives, three late peraluminous monzogranite plutons and numerous Li, Be and Ta-bearing granitic pegmatites. The Lacorne pluton is dominated by biotite and biotite + muscovite monzogranites containing abundant Be and Ta-bearing granitic pegmatites (40-80% volume). The pluton is surrounded by swarms of unzoned or poorly zoned spodumene-rich pegmatite dykes. The La Motte pluton is composed of biotite monzogranites, biotite+ muscovite monzogranites and rare muscovite + garnet monzogranites. Li, Be and Ta-bearing pegmatites are less abundant than in the Lacorne pluton and are commonly associated with molybdenite bearing quartz-muscovite-K-feldspar veins. In the Preissac pluton, muscovite + garnet monzogranites and muscovite + biotite + garnet monzogranites are the dominant rock types. The pluton rarely contains granitic pegmatites and these are generally barren. However, numerous molybdenite bearing quartz and quartz-feldspar-muscovite hydrothermal veins are observed.Li, Be andTa-bearing pegmatites display a crude spatial zonation around their parent monzogranites. Spodumene-rich pegmatites are generally unzoned or poorly zoned and are confined to the surrounding metasedimentary or metavolcanic rocks or crop out in the early gabbroic to granodioritic intrusives surrounding the monzogranites. Ta and Be-bearing pegmatites are usually concentrated towards the margins of their parent monzogranites. The highly fractionated nature ofmonzogranites (high Rb/Sr, low K?Rb, Ba?Sr, Zr/Nb ... ), their peraluminous composition (corundum normative and muscovite bearing) and the numerous occurrences of Ta and Be-bearing pegmatite dykes represent important criteria for the exploration of fertile granites."

Jan 1, 1990

By C. Gosselin, G. M. Payenzo, C. Bazin, M. Desnoyers, G. Chevalier

"ArcelorMittal Mines Canada operates hydraulic classifiers to reduce the silica content of an iron oxide concentrate from 4.5% to less than 1.2% SiO2. Sampling campaigns were conducted to develop a preliminary model for the hydraulic classifier. Results show that iron oxide and quartz are respectively concentrated in the coarse and fine size fractions of the classifier feed. The mineral partition curves in the classifier and the size distribution of the minerals in the feed are used to simulate the classifier operation in order to identify the source of variability observed in the daily plant production data. Results indicate that most of the variation is probably caused by unsteady operating conditions of the classifiers.INTRODUCTION Hydraulic classifiers are a class of gravity separation devices (Wills, 1992) used to classify particles according to their size and specific gravity. Hydraulic classifiers also known as density separators (Hearn, 2002) combine hindered settling and upward flow of water to selectively entrain light particles to an overflow stream. Denser particles settle to an underflow stream. Hydraulic classifiers are used for various purposes ranging from cleaning of coal (Das, Sarkar, & Mehrotra, 2009), recovery of chromite from plant tailings (Kumar, Tripathy, & Rao, 2009) to upgrading iron oxide concentrate (Hearn, 2002). ArcelorMittal Mines Canada operates several hydraulic classifiers to upgrade an iron oxide concentrate by removing fine quartz and other light minerals from hematite that is the main iron oxide mineral. A project was initiated to analyze the operation of the classifier in an attempt to identify the source of the variability in the production results and to assess the potential of increasing iron recovery in the classifier. One possible disturbance for the classifier operation is the change in the classifier feed composition and size distribution, while the other considered disturbance is the operation of the classifier. The paper is divided into five sections. The first section summarizes the ore processing sequence for the production of iron oxide pellets to identify the position of the hydraulic classifier in the process. The second section describes the hydraulic classifier. The third section discusses the sampling campaigns conducted on the hydraulic classifier. The method used to process the data from sampling, the results of the data processing and simulation of the classifier are discussed in the remaining sections."

Jan 1, 2012