Search Documents

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015

By Jesus Gomez, Mary Nodine

Rigid inclusions are widely used in the U.S. as a ground improvement tech- nique, particularly for industrial, low- rise and highway applications with poor subsurface conditions, where control of settlement is necessary. Rigid inclu- sions consist of grouted or concrete elements typically 12-24 in (305-610 mm) in diameter that may or may not be reinforced with a center bar. Typical soil conditions where rigid inclusions are feasible might consist of a surface layer of fill and natural, granular soil, followed by a stratum of soft silt or clay overlying a dense or stiff formation. Rigid inclusions are installed from the existing ground surface or suitable work platform, through the surface soils and through the soft, compressible layer, and into the deeper layer, which is less susceptible to compression- induced settlement. Typically, when used to support an extended area surcharge, the inclusions are installed in a rectangular or triangular pattern at regular spacings ranging from 5-12 ft (1.54 m), depending on a variety of factors. The rigid inclusion system is often capped with a load transfer platform (LTP), whose function is to direct a significant portion of the applied load toward the rigid inclu- sions. Additional load is transferred to the rigid inclusions through the upper fill soils above the compressible layer. The rigid inclusions transfer the applied load axially to their tips and into the deeper layer. In the U.S., rigid inclusions are mostly installed using displacement auger systems. The use of a dis- placement auger has significant advantages. It produces zero to near- zero spoils, which is an important environmental consideration. The

May 1, 2023

By Dan Brown

Deep foundation contracting for transportation projects in the United States has typically followed the design-bid-build model in which contractors bid on a specific work product according to relatively inflexible prescriptive specifications. With continuous flight auger piling and the many types of proprietary drilled displacement auger piling, there appear to be advantages to contracting this work according to a different model. This paper provides a discussion of the use of a performance specification for this work in which the contractor has greater freedom to choose the most appropriate foundation system and also greater responsibility for the performance of the completed foundation. With public agencies subject to open bidding, this type of contractual arrangement presents opportunities to encourage innovation. There are also challenges for implementation in public works projects, notably the selection of qualified contractors and the verification of performance requirements on production foundations.

Jan 1, 2006

By Ahmed Elmekati, Frederick C. Rhyner, Steven R. Lowe

"The current phase of the Pacific Park development (formerly, Atlantic Yards) in Brooklyn involves constructing buildings on a platform over an existing LIRR rail yard. To preserve the maximum amount of space in the already congested yard and protect the yard which remains in service during construction, high capacity foundations are being designed well above previous capacities in the area. In addition to spread footings and small mats, various diameters of drilled piles are being used at design capacities ranging up to 600 tons. The piles are generally grouted at low pressure, up to about 50 psi. Load tests for various drilled elements, including piles, tiedowns and soil anchors, have confirmed allowable side resistance (bond) stresses in dense sand ranging from 20 to 30 psi. Testing with different rigs and operators has shown that down-the-hole hammers are feasible, but the installation techniques, types of equipment and size of the pile make a significant difference. The results show that more cost-effective foundations are possible when ample testing confirms expectations.I INTRODUCTIONThe Long Island Rail Road has operated a mainline on Atlantic Avenue since the 1800s, with a terminal at the intersection of Atlantic and Flatbush Avenues. In the early 1900s, the mainline was reconstructed in a cut and cover tunnel section. The LIRR’s Atlantic Yard was constructed circa 1908 to service the terminal. It was depressed about 25 feet below street grade to coincide with the LIRR’s mainline tunnel under Atlantic Avenue. Record drawings indicate that the gravity retaining walls lining the perimeter of the yard and other ancillary structures had been designed for an allowable bearing pressure of five tons per square foot (tsf). Perhaps by coincidence, the mat foundation for the tower of the Williamsburg Savings Bank was also designed for five tsf in 1929.Figure 1 shows a typical geologic section through the site. The geology and subsurface conditions in this part of Brooklyn consist of fill generally five to 20 feet deep underlain by dense to very dense sand and gravel; in places, with numerous cobbles and boulders which make pile installation challenging. The sand strata that are on the order of 150 to 200 feet thick were laid down by glaciers during the last ice age and have been heavily precompressed. The sand strata are underlain in places by remnants of the Cretaceous-era Raritan Clay formation and Fordham Gneiss bedrock. Because of this, the sand strata generally provide excellent support for shallow foundations and the allowable bearing of five tons per square foot is usually easily justified."

Jan 1, 2016

By Marcus Daubner, Karsten Beckhaus, Florian Bauer

The construction industry can and needs to contribute to a more sustainable world. Accordingly, geotechnical works potentially have a significant share. In this context, Bauer understands “sustainable products for geotechnical works” as those that may cause less emissions and increase the sustainability of construction activities. In order to structure the efforts and systematically pursue sustainable targets in the construction sector, and in the specialist foundation industry, the “17 sustainability goals” presented by the United Nations in their AGENDA 2030, can be used for general guidance and for continuous improvement. Benchmarks for relevant economic and social objectives, mainly with environmental aspects, are inevitable. The key parameter to sustainable products for geotechnical works in the focus of this paper is the optimisation of processes on site needed to fulfill the client’s building task, including the selection of technologies and construction methods with minimum environmental impact and minimum carbon footprint.

May 1, 2022

By Jamey Rosen

A Project Information Management System (PIMS) was developed to manage and analyze QC data at the Herbert Hoover Dike Rehabilitation Dam Modification Cutoff Wall (owned by the Jacksonville District of the United States Army Corps of Engineers). A special feature of this PIMS was its geospatial component. Data collected from Bauer drill rigs were automatically “geoprocessed” into threedimensional features representing the predrill, jet grout, and Cutter Soil Mixing panel elements, as well as calculated verticality and overlap metrics. These features were visualized in interactive planimetric, profile, and 3D views that facilitated several quality control activities during the project.

By KeerthiRaaj Subrmanian, Muthukkumaran Kasinathan

"A railway embankment is under construction between Nagapattinam to Thiruthuraipoondi covering 36.5 km. The sub-soil strata comprises of soft clay extending up to 10 m below existing ground level, which is subjected to stability and settlement problems. A trial stretch covering about 5 kilometer was improved using Prefabricated Vertical Drains (PVD) with surcharge was recommended to accelerate the consolidation settlement. The geotechnical characteristics of the subsoil are examined through laboratory tests on representative soil samples. Recent improvement in the finite element analysis has facilitated modeling of PVD in finite element software for computing the settlement magnitude and time rate of consolidation. In this study the theoretically predicted settlement magnitude and time rate of consolidation from Terzaghi.s vertical consolidation, Barron's radial consolidation are compared with the analyzed FEM results for both the cases with and without PVD improved embankment. The comparative analysis between FEM and predicted data hold good for stresses and the associated deformations. The excess pore water pressure was significantly lower and their dissipation was faster in case of embankment with vertical drains. Thus PLAXIS 2D tool shows fairly convincing results in comparison to the theoretical solutions.1. INTRODUCTIONFrom the earlier times civilization has been developed in a fashion either at the banks of river or near to the shore region, because of the easier availability of food and water. This over centuries made them as huge cities, consequently population rise made the increased necessity of highway, railways, port and even more ground for construction. As a stake researchers are pushed to make a low bearing ground into a massive carrier of skyscrapers, embankment, bridges etc. These low bearing ground suffers from total and differential settlement, slope instability. Hence, numerous ground improvement techniques were followed to eradicate these concerns which include preloading, piling, stone column, vertical drains and geosynthetic reinforcement. Among them Prefabricated vertical drain (PVD) are often used to accelerate consolidation of soft subsoil and has been the main soil improvement method used in improving the soft marine clay deposit (Chu et al.(2004); Chai (2001) and Arulrajah et al.(2003)). Literature review of embankment over soft clay deposit reveals that combination of PVD with preloading is widely considered as an economical and less time consuming ground improvement technique."

Jan 1, 2015

By Matthew Janes

The installation of piles and casings is becoming increasingly difficult as restrictions on vibration become common in major urban areas. The use of high frequency, resonant excitation of a pile or casing permits ease of installation of sections to great depths with near imperceptible vibrations as close as 1 pile diameter. The new Resonant Driver is able to excite a pile at its resonant frequency (up to 150 Hz or 9000 VPM) to produce elevated levels of acceleration, force and displacement in the pile. The combination of extremely high acceleration and controlled levels of displacement allow the pile to slice through varied soil with almost no vibration translated into the ground. In direct comparisons between conventional vibrators and impact hammers the Resonant Driver produces less than 1/50th the vibration. The Resonant Driver results in ground vibration of between 1/20 and 1/40 of common limit levels (1 cm/s or 0.5 in/sec) as close as 1 pile diameter. At a distance of 5 m (16 ft) from the pile or casing vibration levels approach imperceptible levels. The Resonant Driver uses a proprietary algorithm to tune the drive vibration to the changing natural frequency of the pile as it is driven into the ground. By maintaining resonance the energy in the pile is built up like in a flywheel on an engine or a child on a swing. This build up of energy aids in driving and significantly reduces waste. Recent experience using the Resonant Driver is proving the technology can drive a variety of steel pile and casing sections through varied soils. Continued use of the Resonant Driver will create a data base of various pile and casing sections, soil types and achieved capacities.

Jan 1, 2008

By Tracy Brettmann

The Highway 146 Bridge Expansion Project across the Clear Creek Channel in Houston, Texas was designed on driven precast concrete piles. However, during construction, the piles along one side of the bridge along the main channel encountered obstructions and couldn’t be installed. These obstructions turned out to be the remnants of a previous bridge foundation at this location, which was unknown to the designers since that bridge had been demolished 40 years ago. Those old foundations were massive 20 ft by 40 ft (6 m by 12 m) pile caps 11 ft (3.3 m) thick supported on precast concrete piles 37 to 55 ft (11 to 17 m) long. The foundation re-design for these locations involved installing a single 78 inch (2 m) diameter drilled shaft up to 125 ft (38 m) long to replace the originally planned driven pile supported pile cap. The drilled shafts would need to be installed within very tight tolerances since they were supporting a single bridge column directly above it. In addition to drilling through the obstructions, this work would need to be completed from barges in 30 ft (9 m) of water capable of dealing with both the current and tides affecting this area. The shafts were installed using a multi-step process. The first step involved coring a larger diameter 100 inch (2.5 m) hole through the reinforced concrete pile cap and removing the concrete inside. This was followed by the installation of a 72 ft (22 m) long permanent casing to and removing the soil and existing precast piles inside. Finally, the drilled shaft excavations were advanced to the completion depths (uncased) using bentonite slurry as the support fluid.

May 1, 2022

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

By Chandramohan P. V

A unique tension pile where the pull is at a point a certain distance below the top of the pile. The pull is transferred by a cable consisting of high tensile strands. The HDPE duct of the cable prevents bond between the strands and pile concrete in upper portion. While soil friction on the pile will act downwards on the whole length, there is tension in the bottom portion of pile, there will be compression at the top portion.

Nov 1, 2022

By Mikael Calando, Thomas Joussellin

"San Francisco's rapid growth has caused the city to plan for the Transbay Transit Center Project, a visionary transportation and housing project, that will transform downtown San Francisco and the San Francisco Bay Area’s regional transportation system by creating a “Grand Central Station of the West” in the heart of a new transit-friendly neighborhood that will be home to more than 20 new towers rising a high a 1,070 ft. This paper describes the specificities of using advanced diaphragm wall technology, tooling, equipment and installation practices for deep foundation and permanent underground structures. In particular, this paper will emphasize on the urban constraints, geotechnical conditions, and the novel approaches adopted for the construction challenges of the Transbay Transit Center’s Load Bearing Elements, or Barrette PilesPaperThe Transbay Transit Center Project consists of the construction of a new multimodal, five-story Transit Center located in the South of Market neighborhood near the Financial District in San Francisco. The future Transit Center will incorporate nearly 83,000 square feet of retail, a 5.4-acre rooftop park, an extensive public arts program and bus ramps that will connect the Transit Center to a new off-site bus storage facility and the San Francisco–Oakland Bay Bridge. The new facility will accommodate more than 100,000 passengers each weekday and up to 45 million per year. Additionally, the new Transbay Transit Center will replace the since-demolished San Francisco Transbay Terminal, and nearly 20 towers, such as Salesforce Tower, will take advantage of the height increases allowed through the Transit Center District Plan.The approximately $4.5 billion project features a new five-story structure (including two underground stories) and new bus ramps which include a cable-stay bridge. The deep foundations for the pylon of the bridge (Pylon 9) consist of two each 21 ft x 5 ft barrettes (also called Load Bearing Elements in the US) extending more than 180 feet below grade and 10 feet into the bedrock. The barrettes were chosen because of the combination of high loads, significant depth and small footprint. The barrettes are installed using the Diaphragm Wall technology. Nicholson Construction was contracted by Shimmick Construction to install the cable-stay bridge’s foundation elements."

Jan 1, 2016

By Quanchen Sun, Mohammed Z. E. B. Elsahife, Anthony Fisher, Chris Barker, Jennifer Schooling

A review of the literature shows that pile integrity is a significant concern in pile construction. Recently, a new integrity test, thermal integrity profiling (TIP,) has been put into use in foundation construction. It measures temperature changes and thermal profiles of concrete during curing. Heat generation and dissipation of early-age concrete is determined by the concrete mix, the ground conditions and the shape of concrete structure. The current data interpretation practice is primary based on experience. Anomaly detection through direct analysis of temperature profiles is currently indicative or suggestive and temperature signatures are usually similar, and numerous causes are not easily isolated. The core of the TIP testing technique, i.e. collecting detailed temperature measurements along the pile during the hydration process, is promising but a new interpretation approach is required. In this paper, a new interpretation approach has been developed in which TIP constitutes the first step. An investigative staged process is then followed to establish and assess the anomalies in the problematic regions along the pile employing the combined use of detailed finite element (FE) simulations, the actual temperature data from TIP and genetic evolution algorithms. In each stage, more details could be revealed about the anomalies being investigated including, ultimately, location, size and shape; this staged process enables practitioners to follow a riskbased approach and decide whether or not to pursue subsequent stages depending on the results they get at the end of each stage. This new approach, depending on the stages required for the analysis, will potentially avail practicing engineers of crucial test results about the quality of the pile immediately following pile construction, hence enabling repair and remedial work straight away at a lower cost.

May 1, 2022

By Patrick E. Durnal, Henrik Dahl

"A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM + Harris) designed the $779 million seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofi t was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with the support of various consultants. MARINE FOUNDATION RETROFIT SCOPEThe retrofi t design of the submerged foundations included:??A total of 476 tension and compression micro piles (290- 1140 kips or 1290-5071 kN) installed through cored holes through the underwater bells at 31 pier locations??Fourteen 126/150/164 inch (3.20/3.81/4.17m) diameter CISS (Cast-in-steel shell) concrete shear piles (1160- 2660 kips or 5160-11832 kN) installed through new precast concrete pile cap extensions??Twelve CIDH (Cast-in-drilled-hole) shear piles (1060- 2130 kips or 4715-9475 kN) with 150 inch (3.91m) diameter steel shells to top of bedrock and 30 ft (9,14m) long and 11 ft (3.35m) diameter rock socket installed through new precast concrete pile cap extensions The specifi ed post bid test boring revealed deeper bedrock at one pier location allowing deletion of the rock socket. Thus 15 CISS and 11 CIDH shear piles were installed at 11 pier locations - 9 piers with 2 piles and 2 piers with 4 piles. Cut off elevations for the shear piles ranged from 46 ft to 60 ft (14.0m to 18.3m) below mean sea level and cut off for the micro piles was 8 ft to 46 ft (2.44m to 14.0m) below mean sea level. Almost all foundation retrofi ts required work under limited headroom conditions. Underwater construction connections required innovative design details and construction techniques for each pile type. The 11 piers had 22 precast concrete pile cap extensions installed in pairs and connected by either tremie concrete closure pours or by large pipe struts. The precast pile cap extensions were strapped underwater using large steel bands wrapping around the belled piers with grouted annulus. The precast pile caps were founded with 14 inch (355mm) diameter steel pipe piles, which were either support piles or seismic tension and compression piles. The seismic piles were connected in grouted corrugated steel pipe sleeves cast into the new concrete pile caps."

Jan 1, 2007

By Florian König

It is well known that the bearing capacity and stiffness of displacement piles may increase significantly with time, a phenomenon usually referred to as set-up. In cohesive soils the set-up is commonly explained by consolidation processes in which the dissipation of the excess pore pressures around the pile leads to an increase in effective radial stresses. Recent case histories show that set-up may also occur in sand over a period which exceeds by far the consolidation process. Therefore, other effects apart from the dissipation of excess pore pressures must contribute to this long-term set-up effect. This paper presents the results of a series of multiple pile load tests on prefabricated concrete piles which capture the effect of pile set-up empirically. The main characteristics of the set-up trend are shown with respect to soil type, pile dimensions and distribution over the pile length. Possible reasons for pile set-up like consolidation and stress relaxation after the end of driving are examined using a finite element model which simulates the pile installation process.

Jan 1, 2006

By Barry C. Roth

Driving of large piles in water can impact marine wildlife. Bubble curtains can mitigate these adverse effects. The procedures for and preliminary results of monitoring airborne, waterborne and groundborne vibrations with and without bubble curtains on a test project involving 2.438 m piles to 110 m is reported here. We observed fish kills and sea lions apparently fleeing the area. These phenomena were presumably due to the extreme acoustic effects of the powerful hammers which generated waterborne sound intensities locally in excess of 240 dB. This waterborne pile driving noise data collection undertaking is believed to be the most extensive ever attempted.

Jan 1, 2001

By Wanchai Teparaksa

Pile deviation generally can happen after installation of driven pile particularly in soft soil layers. In this case study, all 242 diameter 0.8 m spun piles were deviated from 20 to 820 mm. The large deviation was caused by lateral soil movement in the top very soft clay layer of thickness about 23 m. This very soft marine clay is very sensitive and anisotropic having high water contents of over 120% and low undrained shear strength of 5-10 kN/m2. The remedial works were carried out based on theory of load transfer and soil-structure interaction. All deviated piles were rectified and used as the foundation piles with strictly controlled pile load tests. The construction of a nine-storey building was successfully completed founded on the rectified piles and it has been opened for the service for over two years.

Jan 1, 2002

By Adel Hanna

Earth pressure acting on piles driven in sand is playing a major role in estimating pile capacity. In literature, researchers entertained simplifying assumptions in estimating the earth pressure acting on the pile's shaft, ignoring the effects of pile installation and pile size. Empirical formulae were introduced based on laboratory or field test results, where major discrepancies can be found among these formulae. In this paper, the theory of cavity expansion and the finite element technique will be used to establish the effects of pile installation technique and pile's diameter on the earth pressure acting on the pile's shaft and accordingly on the values of the existing coefficient of passive earth pressure and overconsolidated ratio. It is of interest to note that pile driven technique and pile's diameter have significant increase on the earth pressure acting on the pile's shaft and accordingly on the overconsolidation ratio in case of loose or medium sands, while they may cause crushing and dilation in case of dense sand. Keywords: Single pile, Cavity expansion, Cohesionless soil, Driven piles, Numerical modelling, Finite element technique, Earth pressure.

Jan 1, 2003

By Fabio Santillan, Lyndon Bedford

"This paper presents the main features of the Wolf Creek Dam Foundation Remediation Project, highlighting the innovative construction approach and stressing on how the collaboration between the contractor and the owner became a key element for the success of this project.The main rehabilitation contract, $341 M, was awarded in 2008 for the construction of a 980,000 sqft concrete barrier. Most of this 2ft-wide concrete barrier wall is being built to depths reaching 277 ft using innovative construction techniques proposed by the contractor and under quality control measures that exceed by far the industry standards.The construction of the barrier wall entails the use of nine different foundation techniques which run concurrently following very stringent requirements in terms of verticality, distance between open elements, strength, permeability and dimensions that control the installation sequence of each barrier wall element.The innovative construction approach by the contractor and the collaborative efforts by the contractor and the USACE (“US Army Corps of Engineers”) have brought this unique and very difficult project to a successful completion, setting new standards in the dam foundation industry and nine months ahead of scheduleINTRODUCTIONWolf Creek Dam is on the Cumberland River in south central Kentucky. It provides hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. The lake is a source of recreation that has attracted more visitors (4.89 million) than Yellowstone National Park (2.87 million).The dam and its adjacent reservoir reside upon a heavily Karst bedrock foundation. In late January 2007, the USACE placed the dam under a 'high risk' for failure designation. As a temporary measure, the pool elevation was lowered to 680 ft Above Main Sea Level (“AMSL”), 80 ft below its maximum capacity, with huge impacts to the local economy while the major, and ambitious, $ 594 million remediation program to bring the dam back to its full operating condition was carried out.The main rehabilitation contract of $341 million was awarded in 2008 for the construction of a 980,000 sqft concrete cut-off barrier. Most of this 2ft-wide concrete barrier wall has been built to depths reaching 277 ft using innovative construction techniques under quality control measures that far exceed the industry standards."

Jan 1, 2015

By Stefan Mewes

Europe’s second-largest seaport has installed a new combi wall consisting of pipe piles, sheet piles and inclined shaft grouted piles to support it. The new Liebherr piling rig with swinging leader was used to drive shaft grouted piles into a very dense soil layer of sand with glauconite. The 60 m Liebherr swinging leader was suspended at an inclination of 45° via a suspension frame and suspension ropes from the crawler crane. This inclined installation of shaft grouted piles via freely hanging swinging leader, as used for this project, is unique in Belgium. Moreover, the pile length of 43 m is a novelty for this type of pile. Shaft grouted piles consist of a steel profile with a separate box-like pile shoe with an open top. A thin grout is injected via an injection pipe during driving and emerges just above the pile shoe. As the pile is driven further down, so compressing the ground, the space above the pile foot is immediately filled with grout under pressure. This piling system is ideally suited for the transfer of high tensile loadings. It is a method to increase geotechnical load-bearing capacity and to reduce negative skin friction during pile driving.

Sep 1, 2022