Search Documents

By Lisa R. Papandrea, David Chen, Walter E. Kaeck

"Construction of the University at Buffalo’s new School of Medicine and Biomedical Sciences (UB-SMBS) required excavation in variable ground to a depth of more than 40 ft adjacent to the NFTA Metro subway and Allen Street Station. Complicating the building design and construction, the new medical facility incorporates the at grade Station entrance building, requiring a combination of temporary and permanent excavation support structures, a complex sequence of ground support installation, and a mix of shallow and deep foundations to accommodate the large floor spans and concentrated column loads introduced by building over and adjacent to the Station entrance. Excavation and foundation construction was challenged by a stratified soil profile with interlayered and sensitive sands, silts and clays and complicated groundwater regime with perched and regional water tables. Efficient construction required ongoing coordination between the design team and contractor, careful field observation, and construction monitoring in several facets of below grade construction. This paper describes the design and construction of excavation support structures and foundations to manage the variable ground, congested site conditions, and complications of building adjacent and above an active subway station. Use of site instrumentation and monitoring data to provide guidance in construction when unanticipated field conditions arise is illustrated. Lessons learned in installation and sequencing of excavation support, groundwater control and foundation construction are also discussed.INTRODUCTIONUniversity at Buffalo President Satish K. Tripathi heralded the new School of Medicine and Biomedical Sciences (UB-SMBS) as a future linchpin of UB’s downtown campus that will revitalize the area and enhance western New York’s emerging bio-sciences corridor. The $375 Million, 628,000 square foot, eight story building with two basements is expected to house 2,000 faculty, student and staff allowing UB to increase class size from 140 to 180 students. It will be constructed above the Niagara Frontier Transportation Authority’s (NFTA) Allen Street Station, creating a direct connection to Buffalo’s light rail system. The 200 ft x 400 ft site is bounded by Main Street, High Street, Washington Street and the Roosevelt Apartments and adjoining parking lot at the west, north, east and south respectively, as shown in Figure 2. Groundbreaking for the new building was in October 2013 with the facility scheduled to open in early 2017."

Jan 1, 2016

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan, Joseph Toth

The difficulty in material characterization and the erratic response of cemented soil layers, such as caliche in the Las Vegas valley, creates challenges for practicing engineers to reliably predict the response of deep foundations. The focus of this paper is the numerical prediction of axial response in drilled shaft foundations, which are commonly used in infrastructure projects (i.e., bridges and tall buildings) in Las Vegas, NV. The prevalence of hard caliche layers with variation in the degree of cementation add to the complication in numerical modeling. In this study, the applicability of two existing t-z models, developed for Florida limestone and soft rock, was evaluated based on numerical simulations of three bi-directional load tests conducted at caliche-dominant sites. The corresponding top-down load tests were also simulated for further assessment. A MATLAB-based finite-difference program, NVShaft, has been used to implement the mentioned t-z models in axial load analysis. Complexity originating from drilled shaft construction and the interaction with caliche during one axial load test resulted in a stiffer predicted response compared to measure data. For the other two load tests, both t-z models produced comparable load-displacement responses. It was observed that the t-z model for Florida limestone predicted relatively stiffer responses and higher drilled shaft capacity.

Sep 8, 2021

By Marco Fellin, Van E. Komurka

Significant cost and construction benefits were obtained from performing a bi-directional static load test prior to construction on the Russell Street Bridge Replacement project in Missoula, Montana. The project utilized 24 drilled shafts to support two three-span bridges across the Clark Fork River. A bi-directional static load test (“BDSLT”) was performed on a large-diameter production shaft to demonstrate construction methods and confirm design assumptions. Subsurface conditions consisted of gravel with sand to a depth of 20 feet (6.1 m), underlain by gravel with sand, silt, cobbles, and occasional boulders. The test shaft had a nominal diameter of 5.9 feet (1.8 m), and an embedded length of 75.5 feet (23.0 m). The geotechnical engineer of record and the BDSLT test engineer collaborated to optimize the BDSLT jack assembly location within the test shaft, determine appropriate instrumentation locations, and plan the test protocol. The maximum applied test load was 10,707 kips (47.6 kN). Significant benefits were obtained from performing the BDSLT test, including 1) reducing each production shaft’s length by using a higher LRFD resistance factor allowed by having performed the testing, 2) using test-determined unit shaft resistances to evaluate and accept two production shafts that may have otherwise required remediation, and 3) providing the Montana Department of Transportation (and other designers) with increased presumptive unit resistance values in the gravel/cobble/boulder deposits. PROJECT DESCRIPTION The project was constructed in Missoula, Montana for the Montana Department of Transportation (“MDT”). The original bridge was approximately 60 years old, and consisted of a two-lane, 420-foot-long (128-m), four-span, riveted steel plate girder design spanning the Clark Fork River. The bridge was due for replacement owing to its deteriorated state, and the need for increased traffic volume capability afforded by a four-lane structure. HDR was the structural engineer. The preferred bridge alternate was a 459-foot- long (140-m), three-span, welded steel plate girder design. The new bridge was designed to meet current standards in accordance with MDT bridge design and AASHTO LRFD criteria. The new bridge was constructed in phases to keep traffic open during construction.

Jan 1, 2019

By R. J. Yan

There was a plant equipped with a 32000t Hydraulic Press to be built, under which a box foundation of 22.5m x 15m x 14.25m (depth) with a base slab of, varying thickness was proposed. The subgrade reactions, bending moments and settlements needed to be determined by means of in-situ model test. A model of the same materials as the prototype scaled to l/10 was embedded in-situ with simulated depth in the bedrock. A lot of data obtained from 39 bench marks, 32 elongation measuring points, 30 couples of electric resistance strain gauges and 24 pressure cells attached to the model foundation enables all the quantities required to be found out. Since it was put into operation, the settlements measured has reasonably agreed with the test results and the foundation has been in good condition.

Jan 1, 2010

By Richard Guenther

As available space in urban centers becomes more scarce, builders and developers are increasingly turning to vacant, existing structures to meet cities' growing needs. The developers of City Ridge Roadside Development and North America Sekisui House (NASH) - - found a suitable site for their "urban village" at the former Fannie Mae headquarters complex on Wisconsin Ave. NW in Washington, D.C., which had been vacated in early 2018. The urban village will consist of eight new structures centered around the building that currently sits on the site. All told, the project will include 687 residential units, a 150-room hotel, over 150,000 sq ft (13,935 sq m) of retail space, and 62,000 sq ft (5,760 sq m) of office space. A below-grade parking structure will extend across most of the footprint. The Fannie Mae building, which was designed in the Colonial Revival style to mimic the Governor's Palace in Williamsburg, Virginia, was named a historical landmark following a request from the development team. The central portion of its existing masonry structure was built in 1956 on pile caps with small-diameter cast-in-place piles. Two wings, which were added in 1962, were built on belled caissons. There are three levels above grade and one below.

Feb 1, 2022

By Cassandra A. Wetzel

"Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.INTRODUCTIONRock-socketed mini-piles are a common and desirable deep foundation alternative to support loads more than 40 tons in New York City. Limited vertical clearance, accessibility, vibration control, and load capacity make this pile type attractive; it also does not require a static axial load test when socketed into rock. This added benefit makes this alternative all the more feasible.The installation of a drilled pipe extending to bedrock through a glacial till deposit presented challenges to the contractor and engineers to confirm the casing is seated sufficiently into the rock prior to drilling the rock socket. The loss of soil between the steel pipe and the till/bedrock interface can compromise the performance of the pile and soil loss can result in settlement of the ground surface.This paper presents the design and construction method changes made on one project during the installation of ten limited access rock socketed mini-piles."

Jan 1, 2017

By Anburaj C., Srinivas A.

Deep excavation with support system is required to construct various part of underground structures like shafts, stations and entry structures etc. These structures have to be constructed using permanent or temporary embedded retaining walls with support system. The selection of a suitable type of retaining wall will depend upon the geological condition present in the particular location, time, cost and available equipment etc. In Bangalore Metro Rail Project, secant pile wall is adopted as the temporary earth retaining system and depth of excavation is about 20 m. It is designed initially based on bottom up construction methodology with 3 level of struts and 3 level of anchors but at later stage due to time and other construction related issues, it is decided to change the configuration to 6 levels of strut. Generally, in deep excavations, all the underground structures should be designed and checked for the critical forces from both permanent stage and construction stages. Since, secant piles are used as temporary retaining wall, only construction stage analysis is carried out to get the governing forces and deformation. In construction stage analysis, soil layers are defined with boundary conditions and the surcharge during construction and surcharge from actual building near the secant pile are considered. This paper discusses the effect of change in the support system from anchors to struts and how these changes in the support system affect the behavior of secant pile and subsequently adjacent buildings present in the influence zone of the excavation. As a result, in changing from anchors to struts, the wall displacement, strut forces and ground movement on the adjacent ground and buildings increases. The increase in deflection, ground movements and strut forces occurs during backfilling sequence of the underground station excavation. During backfilling, struts has to be removed and this imparts higher magnitude in deflection, strut forces and ground movements.

Nov 1, 2022

By Sanjay Gupta, Sorabh Gupta, Ravi Sundaram

A geotechnical forensic evaluation of piles for an industrial facility in Haryana was performed to assess the quality of the piles and to evaluate piles installed using two different types of rigs. Low strain pile integrity tests were performed on all piles to assess the pile length and possible presence of structural defects. Coring was done through questionable piles for the clinching evidence of concrete quality and pile length. Probe holes adjoining piles helped confirm the bulging of piles at shallow depth. The paper highlights the importance of implementing a well-planned quality assurance program to confirm that all piles installed are of the desired quality.

Sep 1, 2022

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2013

By H. Shiri

Iran's largest natural gas field is South Pars, geologically an extension of Qatar's 900-Tcf North Field. South Pars was first identified in 1988 and originally appraised at 128 Tcf in the early 1990s. This Field contains 38.6 % of the gas resources of Iran and is regarded as the largest offshore gas field in the world. Offshore geotechnical site investigations are one of the key activities of upstream fields operators to supply the EPC contractors with the required results for designing approaches of offshore complexes. In the mean time a lot of marine site investigations have been carried into execution within the phases of South Pars development. The authors are currently trying to create the fundamentals of investigating the small- and large-scale spatial variability of the South Pars Gas Field in Persian Gulf/ IRAN. Part of this investigation is the providing of an extensive data base of the offshore geotechnical properties of South Pars. Such a data base, will enable a model to be developed of the large-scale variability of these properties. In addition, this data set will provide a data whereby general trends to be established, as well as, providing relationships between geotechnical parameters and spatial parameters utilizing probabilistic and data mining methods like ANN (Artificial Neural Network) in Geotechnical Engineering.

Jan 1, 2006

By Haoran Zhang, Chu Ho

A recent design-build project in New York involved various degrees of additions and improvements to four existing transit stations. Reuse of the existing foundations was considered a more sustainable alternative than constructing new foundations for the project. This approach mitigated the extent of demolition work and limited the amount of downtime for track operations. A key challenge for reusing the existing foundations was the lack of as-built drawings. In order to obtain some measure of confidence for the proposed foundation reuse, non-destructive investigation technology was adopted to evaluate the structural integrity of the piers and foundations. A total of 47 piers for the existing passenger platform were investigated for possible reuse. Several test pits, excavated to verify the foundation type and configuration, indicated the piers were founded on a combination of shallow footings and drilled shafts. Pile integrity tests were performed to verify the length of the drilled shafts. Geotechnical capacity of drilled shafts was evaluated for side friction and end bearing resistance, and confirmed using a proof load test conducted from the existing platform structure. This paper presents the investigation methodology and discusses the approach adopted for geotechnical design of the existing foundations for reuse.

Sep 8, 2021

By Chetan D. Savani, Mike K. Muchard

The necessity to evaluate undocumented foundation lengths is essential in assessing the useable life, need for scour protection, retrofitting, or full reuse of existing bridge foundations. For this purpose, Parallel Seismic Testing (PST) has the best accuracy and is applicable to the widest range of foundation configurations used in bridge construction of any test method. Although not limited to bridges, PST case studies are presented involving two bridges. To preface the case study discussions, an overview of the PST method is given along with its results and analysis thereof. In one of the cases, we were afforded the rare opportunity to see the existing piles being extracted long after the PST testing program was completed. The resulting Class A prediction reaffirms the accuracy of the method. Versatility of the PST method is also exemplified in the two cases presented, where unique situations from complex foundation systems were overcome by analysis to provide successful results.

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022

By Richard J. Hartman

This presentation identifies some of the more common problems associated with cofferdam construction. After the various problems are identified, they are briefly explained and possible solutions and preventive measures are noted. Photographic slides used during the seminar illustrate the conditions. This discussion is limited to cofferdams which are braced structures excavated inside to allow access for construction. The common procedure is to drive sheet piling and then alternatively install bracing and excavate. They can be located either on land or in water. Loads are applied by soil, water, surcharge pres-sure, eccentricities, and impact loads. The loads are resisted by the sheet piling, the bracing, and the soil below the bottom of the excavation; each of these three components must be capable of resisting the applied loads.

Jan 1, 1987

By A. Fisher

The use of thermal integrity testing to verify the quality of deep foundations has increased significantly in the UK and other world markets over the last 5 years. The introduction of distributed fibre optic sensing to this field has broadened the range of applications in which it can be deployed and the types of foundations which can be tested. This paper presents how fibre optic sensing technology can be successfully deployed in the construction environment the range of foundation techniques to which it can be applied. Alongside developments in the practical aspects of thermal testing, progress has been made in establishing assessment criteria which can be used to evaluate the results. This paper presents recent examples of comparative studies on foundations which include both thermal integrity testing, cross hole sonic logging and intrusive coring. The use of distributed strain measurement during pile load testing presents an alternative means to verify the assessment criteria used for integrity testing. This new approach can achieve comparable results to foundation exhumation or intrusive investigation and at a fraction of the cost. This paper presents the findings of several such studies, highlighting the benefits and opportunities for future improvement of the method.

Oct 1, 2022

By Henry Zhang

This paper presents two case studies of large diameter driven tubular steel piles for the ongoing Woolgoolga to Ballina Pacific Highway upgrade (W2B). This project forms part of Australia’s largest regional infrastructure project and will upgrade about 155 kilometers of highway to four-lane, divided road. There are more than 170 bridges on W2B, and driven tubular steel piles are adopted on 43 bridges between Glenugie and Ballina. Driven piles terminating in soil or basalt is a big challenge faced by both designers and piling contractors due to 1) the uncertainty of expected pile unit shaft and base resistance in different soils; 2) whether plugging is formed; and 3) highly variable basalt strength and thickness near top of the rock. If these risks are not adequately managed during design or construction stages, it could lead to unexpected project delay, extra time and cost or pile toe damage in basalt. This paper describes two case studies, one for piles designed to terminate in soils and the other for piles designed to terminate in basalt. How these risks were assessed and managed during detailed design, procurement, hammer selection, pile installation and verification will be discussed in details with lessons learnt summerised in the conclusion.

Nov 1, 2022

By Emad Farouz, Ehab S. Shatnawi

"The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilledshaft diameters has motivated the development and increasing use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft capacity, especially for shafts tipped into loose cohesionless soils. Nevertheless, there remains considerable uncertainty in predicting the performance of base-grouted shafts, particularly for shafts tipped into cohesive soils. To date, there are only two documented design methods for estimating the axial geotechnical resistance of base-grouted shafts: Tip Capacity Multiplier (TCM) and Axial Capacity Multiplier (ACM) methods. A comprehensive test program was carried out during the design phase of the Wisconsin Zoo Interchange project to help optimize the flyover ramp’s foundation design. The test program included installing and testing one base grouted shaft and one ungrouted shaft at two sites with different ground conditions. Based on test results, it was concluded that prediction of the TCM method is well correlated with the measured values for both cohesive and granular soils; however, both methods tend to underestimate the axial resistance. Results also highlighted the importance of the base-grouting criteria in taking full advantage of the base grouting.INTRODUCTIONBase-grouted drilled shafts (BGDS), also known as post-grouted drilled shafts, consist of conventionally installed drilled shafts that contain access grout tubes placed within the shaft during construction. After installing the drilled shaft and achieving the pre-established concrete strength, grout is injected at the shaft tip through the access grout tubes to improve soil behavior around the drilled-shaft base. The tip grout injection improves the overall shaft capacity and reduces settlement through Densifying the in situ soils, compressing any debris left by the drilling process, preloading the soil beneath the tip to mobilize the shaft base resistance within service limits, increasing the tip area, and increasing the side resistance in the lower portion of the shaft."

Jan 1, 2016

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Ambarish Ghosh, Chitralekha Ghatak, Tanumaya Mitra, Tarun Sengupta, Sajib Das, Sankar Kumar Nath

"Currently construction of important structures like bridges, flyovers and high rise buildings in and around Kolkata are in full swing. These structures have mostly pile or well foundations. The design methodology and construction techniques are being employed keeping in view both the safety and economy of the project. The data presented in this investigation have been taken from Geotechnical Investigation report of Component B in connection with construction of Extradosed Cable Stayed Bridge over River Hooghly in Hooghly and Nadia district of West Bengal, India. The investigation site is located within close proximity of Eocene Hinge Zone which is being taken as the principal contributor of Earthquakes in and around Kolkata. Considering the importance of the project detailed and exhaustive geotechnical investigation has been carried out and site specific response spectra have been generated for analysis and design of the bridge. This paper presents site specific response spectra, liquefaction analysis and comparison of lateral load carrying capacity of pile using Winkler approach and IS 2911 guidelines.INTRODUCTIONPile foundations are used to transfer the load of the super structure through soft soil deposit to deeper bearing stratum by means of skin friction or end bearing or both. Pile foundations are regarded as a safe alternative for supporting structures in seismic areas and have been used for this purpose in non-liquefying as well as liquefying soils. But their design in case of potentially liquefiable soil is quite different from that of non liquefiable soil. In liquefiable soil the progressive buildup of excess pore water pressure will cause stiffness degradation and loss of strength which in turn will induce additional shear force and bending moment in the pile. The mechanism of pile behavior in liquefying soil has been investigated by several investigators in the recent years based on observations of pile performance during earthquakes and studies in the centrifuge and Shake Table tests. Exhaustive geotechnical investigation has been carried out along the proposed alignment of the Extradosed Cable Stayed Bridge i.e., along Baropara, Bansberia ROB, Ishwar Gupta Bridge, Saraswati River to collect disturbed as well as undisturbed soil sample, to develop average soil profile and to determine the design parameters. The proposed project site is very close to Eocene Hinge Zone, which is basically a strike slip fault, capable of generating an earthquake of Mw 6.7. Thus it is evident that the proposed Bridge needs to be designed considering the adverse geo-hydrological condition as well as the earthquake aspects needing special attention following the state-of-the-art technology as guided by relevant codes and published literatures. Considering the soil profile of these locations ground response analysis has been carried out using equivalent linear method to determine the site amplification. Site specific response spectra have been developed for the four zones and zone factors have been determined. The computed zone factors are 0.198g, 0.195g, 0.195g and 0.20g for the four zones respectively, much higher than the zone factor 0.16g, which is for zone III, as stipulated in IS 1893:2002."

Jan 1, 2015

By Chris L. Powell, Russell J. Denny

"The remotely located Cockatoo Island iron ore mine off the Kimberley coast in the northwest of Western Australia has been in operation since 1951. The mine was recently expanded up to about 50 m (165 ft) below sea level using staged construction to create a rockfill seawall around the open cut mining operation. Late in 2013, to allow expansion of subsea iron ore mining operations, Wagstaff Piling was engaged to install a seepage barrier through the rockfill seawall and into the underlying seabed sediments.Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of subsea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansions that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative seepage barrier solution using a grout curtain was selected to provide the necessary cutoff to allow access to highgrade ore, while protecting the mine from inundation by the sea.Seawall ConceptThe open cut subsea mining operation consisted of a 3 km (1.9 mi) long narrow pit along the south side of Cockatoo Island that extended to depths of about 50 m (165 ft) below sea level, and were exposed to the open sea on the south side of the pit. Massive tidal variations of more than 10.5 m (34.5 ft) required a seawall founded on the seabed, extending upwards to RL+13, to safely protect the pit from the high tide level rising to above RL+10."

Jan 1, 2017