Search Documents

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

By Kaihui Yang

Volcanogenic massive sulfide deposits are generally considered to have been formed by hydrothermal fluids that leach ore metals out of footwall rocks. However, the necessity for a metal-rich magmatic component in the ore-forming fluid of "giant" ore deposits has been debated over the decades. The solution to this issue is important not only for metallogenic models but also for the mineral exploration. In the hydrothermal leaching model, massive sulfides at mid-ocean ridges are deposited from hydrothermal fluids containing 80 ppm Fe, 6 ppm Zn, 2 ppm Cu, 350oC, and 0.7 g/cm3 density (average data for 21oN East Pacific Rise). A simple calculation demonstrates that such a dilute fluid is unlikely to have been responsible for the formation of the largest ancient massive sulfide ores of greater than 100x106 tonnes, such as Kidd Creek, Brunswick No. 12, Neves Corvo, and Rio Tinto. For such a deposit consisting primarily of pyrite, sphalerite, galena and chalcopyrite (other minerals, including gangue, might account for an additional 10-20%) and even assuming 100% precipitation and retention of the sulfides, more than 790 km3 of vent fluid would be required. For typical water-rock reaction ratios of about 2, this fluid would have to have reacted with about 395 km3 of rock to acquire its metals by conventional leaching processes. This estimate, however, conflicts with the observation that even a giant massive sulfide ore body is usually underlain only by a few cube kilometers of obviously altered rocks. Moreover, this model is not consistent with the observation of hanging wall alteration in many large massive sulfide deposits. The close spatial association between massive sulfides and volcanic rocks, in both ancient and modern sea floors, suggests that direct magmatic contribution should be taken into account in the genetic model. Magmatic fluids, capable of carrying abundant ore metals and volatiles and escaping from magma by depressurization, are well known from modern active volcanoes on land. High concentrations of metals occur in CO2-rich magmatic fluid trapped in felsic volcanic rocks nearby large presently-forming VMS deposits in the eastern Manus Basin (Pacmanus, Suzette) and also in the footwall rocks of Ordovician giant Brunswick #12 deposit in the Bathurst district, New Brunswick. Only 1% of such metal-rich magmatic fluid mixed with heated sea water, that has leached its metals from rocks, would contribute 85% of the total metals to form an orebody. Such magmatic fluids are most likely to be formed from volatile-rich felsic magmas that are prevalent in back arcs, and, if added to the normal circulation system, the fluids could be responsible for the formation of "giant" ore deposits. If this is true, then the study of magmatic fluids in the seafloor volcanic rocks may provide criteria for the exploration of large ore deposits.

Jan 1, 2011

By Kris van Nijen

IHC Merwede, a Dutch supplier of ships and equipment for dredging and mining activities, and DEME, a Belgian dredging and environmental services group, will enter into a joint venture for deep-sea mining activities. Under their cooperative agreement, IHC Merwede will be responsible for the development and construction of technical solutions, while DEME will be responsible for operations. Together the companies will offer a unique pioneering total solution. The joint venture will be known as OceanflORE.

Jan 1, 2011

By A. M. Olivarez

The elucidation of the theory of plate tectonics has provided a conceptual framework for understanding the formation and distribution of different types of ore deposits. For example, we now recognize that certain kinds of mineral deposits are generally associated with a particular type of plate boundary (i.e., massive sulfides often occur along divergent plate boundaries, whereas porphyry copper deposits are typically found along convergent boundaries). During certain geologic time periods, plate reorganization events have changed the relative proportion of different types of plate boundaries. Corresponding changes have been observed in the abundance and distribution of ores deposited during these times. The present study examines the temporal aspects of this relationship; i.e., do plate reorganization events play an active or passive role in ore formation? In other words, do plate reorganizations simply provide a more favorable tectonic setting in which ore formation can occur over significant time periods, or are they directly linked to the mineralization process? We have examined this question by comparing regional tectonic histories with the ages of known massive sulfide and porphyry copper deposits. Because these deposits, in particular massive sulfides, form as a result of hydrothermal activity, we have also compared regional tectonic histories with proxy indicators of this process in the marine sedimentary record. These indicators include increased mass accumulation rates of Ca, Fe, Mn, and opal, characteristic changes in the Sr/Ca and Mg/Ca ratios of biogenous carbonates, and shoaling of the carbonate compenstion

Jan 1, 1988

By Chris Roper

The Gavia Autonomous Underwater Vehicle is a two-man portable AUV that is capable of performing seafloor surveys in water depths to 2000 meters. The standard survey sensor suite includes a dual frequency side scan sonar and high resolution digital camera. Additional survey sensors are currently being incorporated into the Gavia AUV, include Sub Bottom sonar, Swath Bathymetry sonar and Multi Beam sonar. The modular design of the Gavia AUV allows the end user to quickly incorporate new sensors including client developed propriety sensors.

Jan 1, 2005

By William Siapno

Manganese nodules, as metal ores, have for the most part been cast aside from further consideration within this century. However, in the decade of the 90s, rising demand at all levels of society, for clean air give nodules a new - lease on life as a stack gas cleaning agent. Further, the Clean Air act of 1990, mandates enormous outlays to bring systems into compliance with new stringent standards. Quick corrective actions are imperative. Research beginning in the 1960s proved nodules possess unique qualities to remove acid compounds from stack gases. Early this year, the National Science Foundation awarded General Electric an $83 million contract to design a system to extract oxides of sulfur and nitrogen from coal fired power plants. Environmental damage is abundantly evident on the ground, from the air as well as form space. A dirty pall of yellow-brown smog is smothering both animal as well as plant life around the globe. Losses run into billions!

Jan 1, 1991

By Andrea Koschinsky, Luise Heinrich

(for an oral presentation) Activities for preparing future deep-sea mining offer the unique opportunity to study environmental conditions and anticipate adverse environmental impacts prior to the commercialization of the activity. Until know, environmental research has first and foremost focused on understanding direct impacts occurring at the seafloor or in the water column such as the removal of substrate, the suspension of sediment or the creation of particle plumes. Impacts occurring above the sea surface have thus far rarely been considered. The operation of deep-sea mining equipment, as well as of mining and transport vessels will be associated with a considerable energy demand. In the open ocean, this energy will be provided by heavy fuel oil (HFO), which is the cheapest and most common marine fuel. The combustion of HFO will be associated with the release of greenhouse gases and other pollutants. Deep-sea mining will thus directly add to already critical air pollution levels caused by international shipping. To contribute to a holistic assessment of deep-sea mining impacts and to address the previously outlined knowledge gap, we present the methodology to quantify the fuel consumption and associated emissions of a potential typical commercial manganese nodule mining operation in the Clarion-Clipperton Zone (Fig.1). Using the mine set up and energy demand estimates from a study commissioned by the German Federal Ministry of Economic Affairs and Energy supplemented by information from literature, we anticipate emissions of carbon dioxide (CO2), carbon monoxide (CO), methane (CH4), nitrous oxide (NO2), nitrogen oxides (NOx), sulfur oxides (SOx), particulate matter and non-methane volatile organic compounds.

Jan 1, 2018

By Marlene Olivares Cruz

The particles that make up the deep-sea sediments have two main sources: 1) those that are created in situ from dissolved components and 2) those that are washed into the ocean in solid phases from the continents, atmosphere, space and interior of the Earth. Many particles as they sink through the water column reaches the seabed and are known as pelagic sediments with terrigenous, biogenic, authigenic, and cosmogenic components. Among the minerals found in the terrigenous fraction of pelagic sediments are quartz, clay minerals, feldspar, micas, ferromagnesians, and the biogenic fraction with remains of siliceous organisms, such as, radiolarian and diatoms. The chemical nature of marine sediments is controlled by the contribution of particulate matter derived from various sources with varying compositions for the fixing of elements during deposition and the compositional changes carried out within the sediments during diagenesis. In the last decade there have been several studies on the mineralogical composition of seabed sediments, suspended particulate materials and cores, together with paleontological and geochemical data are used for paleoclimatic and paleoenvironmental reconstructions, analyze changes in sea level, stratigraphic correlations and identify past and

Sep 14, 2011

By Lauro Calliari

Detailed geological studies using side scan sonar, bottom sampling and piston cores along the Rio Grande do Sul inner continental shelf and coastline indicate the occurrence of elongate deposits of calcareous shells fragments containing high calcium carbonate content. On the inner shelf these deposits lie at a depth between 15 and 50 meters and have been interpreted as ancient shorelines. They occupy an area of 965 km2 with a economic potential of 1 billion tons. Chemical analyses indicate a mean composition of 34.8% of calcium; 0.16 ppm of fluoride. According to the regional economy such composition make it highly recommended for a variety of uses including poultry feed and cement.

Jan 1, 1995

By Kiseong Hyeong

The Intertropical Convergence Zone (ITCZ), where the southeast and northeast trade winds converge, is the effective climatological barrier that separates the southern and northern hemispheres in terms of dust budget. Asian and N. American dusts dominate in the Pacific north of the ITCZ, while Central and S. American dust prevails south of the ITCZ. In order to understand the nature of latitudinal and depth-related variations of mineral composition in terms of position relative to the ITCZ, deep-sea core sediments were collected from 9°N to 17°N at a 2° intervals along the 131.5°W meridian and analyzed for mineral composition. The amount of illite in surface sediments decreases gradually from 65% at 17°N to 31% at 9°N. In contrast, smectite increases from 11% to 56% southward. The observed mineralogical variation toward the ITCZ is attributed to the increased supply of volcaniclastic material transported via the southeast trade winds from the Central and South America source regions. Smectite-illite transition, a phenomenon that the amount of smectite increases over illite, occurs at around 10°N, the northern margin of the ITCZ. This result indicates that the change in latitudinal position of the ITCZ in the geological past could be recorded by the smectite-illite transition in deep-sea cores. The cores studied show down-core variation of mineral composition from illite-rich at the surface to a smectite-rich clay suit at depths, similar to the latitudinal variation. The smectite-illite transitions observed in these cores are likely the records of changes in latitudinal position of the ITCZ. The depth and age of the smectite-illite transition is getting shallower and younger towards the equator, implying that the ITCZ was located farther north during late Tertiary and has shifted southward to the present position of 5°N~10°N.

Jan 1, 2004

By Eleanor Martin

An examination of the draft Exploitation Regulations from an investor’s perspective. We will look at the commercial requirements of the investment community (debt and equity) in order to provide funding to a deepsea mining project, and contrast this with the position put forward in the draft Exploitation Regulations. We will then recommend suggested amendments to the Exploitation Regulations to assist future investment on this growing industry.

Jan 1, 2018

By Alexander Malahoff

A shipboard research system capable of operating in waters of up to 2,000 meters has been designed and implemented by the Hawai'i Undersea Research Laboratory (HURL) of the University of Hawai'i. It uses a remotely-operated ocean bottom survey camera system, an ROV, the Pisces V submersible, and a submersible emergency recovery system, all aboard the 222- foot R/V Ka'imikai-o-Kanaloa. All systems are operated from the stern of Ka'imikai with a mounted Caley telearm and articulated A-frame system. The system was designed for multipurpose use of the ship for launch and recovery of the Pisces V submersible on a lift recovery line (with or without diver assistance), or night-time operations with an electro-optical cable using either the HURL ocean floor sidescan or photo and video system operated at 10 meters above the ocean floor. The 1.14-inch diameter cable is also used to operate an ROV system. The garage/ROV system can also act as a submersible rescue system with a submersible lift capability. The ship is equipped with a SeaBeam and shallow penetration sediment profiling systems. This integrated system approach to deep ocean floor research will make it possible for HURL to carry out research pro- grams on seamount ocean resources and ocean chemistry and climate in Hawai'i and the equatorial Pacific.

Jan 1, 1995

By Carlos Almeida, Bruno Matias, Stef Kapuskiak, Eduardo Silva, José Miguel Almeida, Alfredo Martins

Underwater intervention operations have been supported by robotic systems such as remotely operated vehicles (ROV) for a long time. In particular challenging scenarios such as the deep sea, the use of ROV systems for environment awareness is in fact the main tool of choice. With the technical advances in autonomous robotics, there is an increased effort in substitute ROVs whenever possible for autonomous underwater vehicles (AUV). These systems don't have tether and thus provide large advantages from the operations and logistic point of view. However the limited options for underwater communications render them impracticable for many tasks were real time environment awareness and direct human control is needed. Emerging applications in underwater mining, both at sea [1] and in inland flooded mines [2] pose additional requirements in terms of operation support needs and environment restrictions. Two main tasks are to be addressed by assisting robots in these underwater mining operations: providing adequate environment awareness for human operators and obtain precise realtime 3D environment modelling (particularly relevant for the mining planning). The use of ROVs with umbilical cable, has in this case large limitations due to the nature of the mining cutting (performed by dedicated systems) that limit manoeuvrability and pose high risk of cutting the cable or damaging the vehicle. In this paper we present EVA (Exploration VAMOS AUV) an innovative hybrid ROV/AUV system developed for operations support in inland underwater mining operations. This robot is always operated without tether, and the can be used in a wireless ROV tele-operation mode using very short range high bandwidth underwater communication systems and in autonomous AUV mode.

Jan 1, 2018

By Stanley R. Riggs

Onslow Bay is a broad, shallow, high-energy shelf system bounded by the Cape Lookout and Frying Pan shoals. It is generally a sediment-starved shelf system dominated by hardbottoms with a scattered and discontinuous veneer of mobile Holocene sediments. Phosphate-rich beds of the Miocene Pungo River Formation crop out in a belt 150 km long and up to 50 km wide across the continental shelf in Onslow Bay, North Carolina. Previous research has demonstrated that a few of these beds contain vast quantities of potentially economic phosphate resources that occur in the surface and shallow subsurface sediments. Onslow Bay contains five phosphate-bearing beds predicted to include up to 20.7 billion tons of in-place phosphate concentrate with total sediment grades ranging up to 22.9% P2O5 and adjusted average concentrate grades of 29.8% P2O5. These phosphates are lithologically and chemically similar to phosphates currently being mined in the nearby Aurora phosphate district in North Carolina. Various lithologies of the Pungo River Formation and associated rock units of Oligocene and Quaternary age crop out on the sea floor to form extensive hardbottom habitats that dominate almost 100% of Onslow Bay. A large proportion of these hardbottoms appear to be sea floor deserts, whereas others are virtual oases with rich associations of benthic organisms. These important differences in benthic community structure appear to be greatly influenced by one or more of the following variables: 1) geologic framework (geologic formation, hardbottom composition, morphology, and spatial orientation relative to dominant currents and waves), 2) texture, movement, and accumulation of surface sediments, and 3) flow rates and chemical composition of discharged submarine groundwater.

Jan 1, 1992

By J. R. Woolsey

In late 1988, the Committee for Coordination of Joint Prospecting for Mineral Resources in South Pacific Offshore Areas (CCOP/SOPAC), Suva, Fiji, consulted the Continental Shelf Division of the Marine Minerals Technology Center regarding low-tech, low-cost, reconnaissance sampling systems for a variety of nearshore needs. Materials of interest to several member island nations included silica and calcareous aggregate for cement manufacture, sand for beach replenishment, heavy minerals, and precious metals. A principal criteria of the system was that it be of low-tech design, and as far as possible, suitable for construction on the islands from available materials. It should also be operable with SOPAC personnel on island vessels of opportunity. The system selected to satisfy these requirements was a convertible drill of basic airlift design, capable of operating with easy modification as either a vibralift or airlift, depending on the desired application. The basic system included a drill pipe constructed of heavy duty 76 mm (3") black iron pipe, divided into three 3 meter sections (for ease of transport), fitted with an air intake manifold and bit at the lower end. A 25 mm (1") galvanized pipe assembled in three similar sections and clamped to the drill pipe served as a water jet to assist in cutting. Air was supplied to the manifold by means of a 12 mm (1/2") pipe also clamped along the length of the drill pipe. Suitable hoses supplied water and air to the upper ends of the respective pipes by means

Jan 1, 1989

By Peter M. Bartlett

The Republic of South Africa ranks among the world leaders in both reserves and production of numerous land-based mineral commodities. Over the last three decades, however, South Africa has also identified several commodities that may exist in commercial quantities in the marine environment. The major targets include 1) placer diamonds; 2) titanium- and zirconium-rich beach sands; 3) sedimentary and concretionary phosphorite and glauconite deposits; 4) manganese nodules; and 5) hydrocarbons. South Africa ranks second in world reserves of diamonds and has potentially enormous sea resources. Diamonds are currently recovered on the Atlantic side from ancient beach gravels in the Northwest Cape Province and from the seabed south of the Orange River to Lamberts Bay. Approximately 100,000 carats (or just 1% of South Africa's total annual production) are produced each year from offshore operations. DeBeers is investing approximately $5 million per year on sea prospecting activities and currently operates three vessels in offshore recovery operations. Diamonds recovered at sea will remain a small percentage of total production because of huge land-based reserves that are mined at a fraction of the cost of seabed operations.

Jan 1, 1986

By Jan Stenlokk

The Norwegian Petroleum Directorate, which is the Government agency for the management of offshore geo-resources including seabed minerals, is about to finish this year’s marine data acquisition cruise in the Norwegian Sea. We would very much like to present the preliminary results of that cruise, including the discovery of a new black smoker and surrounding sulphide deposits.

Jan 1, 2018

By Dan Johnson

The discovery of rich alluvial diamond deposits on Namibia?s Skeleton Coast in 1908 began a period of intense exploration and mining off the coastal sand; and shallow surf zones. In the mid-60s a Texas entrepreneur, Sam Rollins took the search to the seafloor. The inhospitable conditions encountered made the early going difficult. After a slow start, the past 10 years have seen much progress in geologist?s understanding of the deposition mechanics and the use of sophisticated geo-physical and sampling techniques to aid in the discovery of economic deposits. Diamondfields, in a joint venture with BHP and Benguela Concessions, began an exploration program in 1994 for sea-bed diamonds off the Port of Luderitz in Namibia. This program has progressed to a mine development program with the potential of creating a 500,000 carat per year operation. The mining technologies being considered include state-of-the-art, remotely operated sea-bed crawlers and high volume dredges feeding to semi-mobile processing platforms. The company's objective is to use the best proven technology to create an environmentally responsible operation with the lowest fixed operating costs and the longest and safest weather operating window of any offshore operator working Africa's diamond coast.

Jan 1, 1998

By Georgy Cherkashov, Tamara Stepanova, Anna Firstova

INTRODUCTION High tellurium contents in the ancient volcanogenic massive sulfides (VMS) and modern seafloor massive sulfides (SMS) have been reported by V.Maslennikov (Maslennikov et al., 2013). However findings of tellurium minerals in SMS are rather rare. The only reported coloradoite and bi-melonite, have been found in massive sulfides from Rainbow hydrothermal field (Fouquet, 2010). Here we present data about Te - minerals in sulfide chimneys of different ages (up to 84.7 kyr - Cherkashov et al., 2010 ) from Semyenov-2 hydrothermal field. The obtained results The Semyenov hydrothermal cluster was discovered and studied in the course of cruises 30 and 32 of R/V Professor Logachev (2007 and 2009) at 13º31´ N, MAR. This area is associated with an oceanic core complex and associated with serpentinized gabbro- peridotites and basalts. Plagiogranites and tonalites have been dredged on seafloor in the Semyenov cluster area (Cherkashov et al., 2013; Pertsev et al., 2012). In total, 25 sulfides samples have been studied. The major and minor mineralogical phases were identified using reflected light microscope. Major element compositions of ore- forming minerals were analyzed on a Hitachi S3400N scanning electron microscope at the Geomodel Center, St. Petersburg State University (St. Petersburg, Russia) with an AzTec Energy 350 (EDX) detector and an INCA 500 (WDX) detector.

Jan 1, 2018

By Tetsuo Yamazaki

Natural methane hydrate has been scientifically studied as a carbon reservoir globally. However, in Japan, the potential for energy resource has been industrially highlighted. There is less domestic oil and natural gas resources in Japan, but many potential deposition areas for methane hydrate in ocean around Japan are the reasons. Less CO2 discharge from methane compared with coal, oil and conventional natural gas when the same calorie value we get is considered as the advantage for energy resource. However, because methane hydrate distributes in shallower sediment layer in ocean floor, accidental leakage of methane may occur while we utilize methane hydrate. Methane itself has 21-times impact on the greenhouse effect, if it reaches the atmosphere. Therefore, it is necessary to estimate the behavior in the environment after the leakage, if we want to use methane hydrate as energy resource. The mass balance after leakage of methane on seafloor and in water column is numerically studied through the analyses of methane emissions from natural cold seepages and hydrothermal activities in this research. The outline structure of mass balance ecosystem model shown in Fig. 1 is introduced. A numerical early diagenetic model CANDI (Carbon And Nutrient Diagenesis) developed by Boudreau (1996) for simulating the biogeochemical processes such as organic matter, oxidant, nutrient, bi-product, and pH diagenesis in aquatic surface sediments and C. CANDI improved by Luff and Wallmann (2003) for describing the formation process of calcium carbonates in CANDI are used as bases of the ecosystem modeling in surface sediment layer around seafloor methane emission. Two functions such as methane bubble dissolution and bacterial methane oxidation in water column are added to an existing physical plume dispersion model by Doi et al. (1999).

Jan 1, 2005