Search Documents

By Sravya Kosaraju, Christian Ekberg, Stefan Allard

Li-ion batteries are now used in electric vehicles (EVs), plug-in hybrid vehicles (PHEVs) and, hybrid electric vehicles (HEVs). Nanostructured Li(NiyMnzCo1-y-z)O2 is one of the more popular cathode chemistries for automotive Li-ion battery, due to its enhanced properties such as large surface area, short diffusion length, enhanced ionic and electronic conductivity, improved mechanical strength and structural integrity [Pan et al, 2013]. Recycling of Li-ion batteries helps to mitigate environmental effects of virgin metal extractions along with improper disposal of end of life batteries. To fulfill these objectives of the recycling, recovery of pure streams of the involved metals should be considered. In this study, the batteries were first discharged and dismantled in an inert atmosphere (Ar). The electrodes were then heat treated in a box furnace. This was done in order to break the chains of the adhesive (PVDF) and consequently separate the metallic substrates Cu and Al from the electrochemically active compound. This heat-treatment also helped to simplify the dissolution of the metal constituents in the electrochemically active compound from the cathode in the acid leaching process. Solvent extraction was chosen to achieve separation and recovery of metals with higher purity from these leachates. In the scope of the present work, a complete process from the point of dismantling to separation of constituent metals using solvent extraction was studied.

Jan 1, 2014

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By Chandra Sekhar Gahan

The present study aimed to investigate the depyritization of coal using iron oxidizing and sulphur oxidizing acidophilic chemolithotrophic microorganisms in an iron free 9K growth medium at varying pulp densities. Three different coal samples used in the shake flask study from three different countries such as domestic anthracite (Korean), Indonesian and Chinese lignite. Experiments were carried out in batch at a controlled temperature of 35 °C and varied pulp densities of 8%, 10% and 12% (w/v) with a working volume of 100 ml containing 10 ml of microbial inoculum and 90 ml of the iron free 9K growth medium. Coal samples were crushed and ground to fine size fractions <100 microns by attrition mill wet grinding. The progress in the experiments were followed by the regular measurements of pH, redox potential, viable planktonic cell count, residual Fe2+ ion concentration, amount of acid addition and amount of slaked lime addition. The pyritic sulfur removal percentage varied between 90-95% with highest sulfur removal with China coal (95%) followed by Korean Coal (93-94%) and slightly lower level for Indonesia coal (90%). However the pyrite oxidation was highest for Korean coal ranging between 78-80% followed by a similar level of pyrite oxidation of 50-61% for the Chinese and Indonesian coal. It was found that 10-12% pulp density would be fairly feasible for all the different coals tested leading to an economical process. Another benefit from this study is the iron free 9K growth medium, which will reduce the operation cost and overall it?s an environment friendly process.

Sep 1, 2012

By M. Bhartia

India is the 5th largest producer of steel in the world and is slated to produce more than 180 Mt by 2020. Expectedly about 50 % of this would be through the Blast furnace route and the rest through Sponge iron / DRI route. Considering that there will not be any major change in iron making technology by that time, the Blast operation would require lump ore (10-40mm) with around 64% Fe grade and sinter fines (<10mm) with 60% Fe (min) as its feed. DRI process would need calibrated ore of size 5-18 mm as the most suitable size of feed. It is also expected that of the total requirement of ore for the DRI route a significant part would be DRI pellets. In India, there is considerable debate going on regarding the technology to be adopted for the processing of iron ore and there is a lack of clear consensus. The above scenario indicates that the processing requirement of iron ore in the country would involve both washing technology as well as beneficiation technology. CDE Asia Ltd is in the forefront of iron ore processing in the country and the experience gained by the company over the last few years of functioning has led the company to believe that route to be adopted depends on the end product requirement and the starting grade of the feed. Keeping in mind the nature of the feed required for the Blast furnace & DRI operation; it is obvious that good washing technology would be highly beneficial to the iron ore industry. Depending on the grade of ore available the limits of washing will be decided and equipment for lump ore beneficiation such as jigs could be incorporated into the washing circuit. Scrubbing of ore either before washing or selectively scrubbing the lumps could be necessary. Very low grade ore and jig rejects would be required to be totally ground and beneficiated for the production of pellet feed in order to utilize the iron ore resources entirely. Another source of ore for pelletisation would be slimes generated from the washing process as well as the huge quantities already available in the tailings dams in the operating mines. Deslimimg and magnetic route of beneficiation could release at 30-40% of the Fe locked up in these tailings ponds/dams. The paper describes the concept with examples from operating plants and proposes how the adoption could be engineered through test work and proper plan of integration. Keywords: washing, beneficiation, iron ore, lumps, sinter fines, pellets, jigs, screens, evowash, nanowash, thickeners, log washers, drum scrubbers

Sep 1, 2012

By Ayumu Tokumaru, Shuji Owada, Gangfeng Liu

"Several million spent catalytic converters are disposed annually worldwideandeach containing about 0.5-1g ofplatinum and 1-2g of all the platinum group metals (PGMs), then,it is fairly significant to recover PGMs from the spent automobile catalyst. The PGMs’ recovery is a proven technology, including pyro-and hydrometallurgicalmethods, and the highestrecovery can achieve approx. 98 wt.% by acid-leaching method, but theserecyclingtechnology seems to be too highlyenergy-consuming. SincePGMs aredistributed only in coat layer in spent catalyst, it is of great significance to enrich the coat layerwith some physical methods as a pretreatment.In this paper, according to the double-deck structureof the catalyst andthe different properties of the two main compositions, alumina-ceria phase of coat layer and cordieritephase of substrate, the concentration of the coat layer was investigated by combiningthree kinds of physical separation technologies, heating-quenching, crushing and surface grinding. In the first stage, thermal stresscouldgeneratebetween the two phasesby thermal expansion difference,to producefracturesin the thinnest part of coat layerand micro-cracksin coat layerand at the interface of coat layerand cordierite substrate. The second stage of crushing, by jaw and roll crushers, could break dominantly the coat layer and the third stage of surface grinding, carried out by attritor, promoted further separation and concentration of coat layer fromthe substrate.We also improved the attritor grinding by adding a new lift-arm to the cell for achieving better mobility of sample particles in the selective surface grinding."

Jan 1, 2014

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014

By A. J. Lynch, D. K. Tungpalan, Y. Reja, E. C. Avelar, G. Figueroa, S. Gómez, R. Alanis, M. A. Corona-Arroyo

"Have you been on a mine site? This question was posed by Emeritus Professor Alban Lynch to Higher Degree by Research (HDR) Students from the Sustainable Minerals Institute - Julius Kruttschnitt Mineral Research Centre (SMI-JKMRC) in the Student Technical Presentations in 2015. From that question, five HDR students from SMI-JKMRC organised a placement on mine sites in Mexico. The SMI-JKMRC is well known for its tradition to provide their students with opportunities to enhance and test their skills in mineral processing plants. The Student Venture became a short internship for HDR students which had the objective of establishing collaboration with mining companies in Australia and overseas, and of providing a unique experience for the HDR students in regard to their training, professional development, networking and cultural interchange. In return for the companies’ support, the students conducted plant audits to evaluate the process performance thereby providing valuable data to the host company. The 2016 Student Venture was held at the Grupo Peñoles & Grupo Fresnillo in Mexico, in which three mine sites received five HDR students from JKMRC and one young researcher from Universidad de Guanajuato (UG). This paper describes the positive outcomes for the mining company and the students for this experience. The Venture was considered very successful, as it provided valuable training for the students as well as in depth information about the operation of the comminution and flotation circuits of the host sites for the Grupo Peñoles & Grupo Fresnillo. The experience also provided an opportunity for an exchange of knowledge between the HDR students and the site personnel from the host operations. The indication of the success of the experience for all involved was the support of the host company in future student internships."

Jan 1, 2018

By Arun Appadurai

Pneumatic transport systems play a vital role in conveying discrete particles over a sizable distance with minimal energy consumption. However if such a system is not designed keeping particle physics in mind, it leads to intractable problems which could possibly assume dangerous proportions, including but not limited to expensive redesign of the entire system. This paper describes a novel method, which harnesses the powerful technique of Computational Fluid Dynamics (CFD) to investigate a problem occurring in rotary kilns using coal as a major fuel source. In some of the sites, a unique phenomenon of abnormally high CO emission was observed and owing to the highly random nature of occurrence, it was difficult to scientifically investigate the problem and its cause. Most of the published solutions for the high CO problem tend to concentrate on the incomplete combustion aspect of the kiln and resolve the situation by increasing the air supply thereby improving the stoichiometric ratio of combustion. This paper offers an alternate correlation that relates high CO emissions to the phenomenon of coal delivery fluctuations caused by the sub-standard operation of the coal transport system. A CFD model for the coal delivery pipe is validated by utilizing the actual process data sourced from the measurements taken from a functioning plant. The results of the model are used to derive correlative conditions that point to the unstable operating conditions of the coal delivery pipe prevalent in the industry. The conclusions are summarized into a series of recommendations for optimized design of coal delivery systems which are implemented in a pilot plant. The results irrevocably prove a statistically significant reduction in CO emissions without resorting to increased air supply and power consumption. Keywords:CFD, Pneumatic Conveying, Saltation Velocity, Particle Flow

Sep 1, 2012

By T. J. Chen

Stone coal containing vanadium is an important vanadium resource in China. Roasting and oxidation of vanadium is the foundation for extracting vanadium from stone coal. This article takes stone coal vanadium ore in Tongshan of Hubei Province as research target to conduct oxidation roasting test on it by using a self-developed low-sodium compound additive and a new optimized technology. Firstly, use potentiometric titration, X diffraction, energy spectrum and electron probe to study valence change, occurrence and phase transition of vanadium during oxidation roasting process. On this basis, primary work is done on oxidation kinetics of vanadium by exploring the steps that control reaction rate during vanadium oxidation process and determining the related dynamic parameter ? apparent activation energy. The study shows that occurrence of vanadium in stone coal of Tongshan is mainly in illite, and that the result of phase transition in roasting process is disappearance of illite containing vanadium, formation of soluble vanadate and potassium feldspar, albite. It further demonstrates that oxidation process of vanadium is step by step (V(?)? V(?)? V(?)), and its oxidation reaction is controlled by diffusion kinetics whose dynamic apparent activation energy is E1=81.19kJ.mol-1.

Jan 1, 2014

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

By W. Y. Liu

A sulfate reducing bacteria strain (named SRB-A) is isolated from sanitary wastewater by using anaerobic technology of Hungate. The studies of physiological, biochemical and phylogenic of the isolated strain are carried out. The colonies of the strain are circle. Cells that are slightly curve, rod-shaped with the size of 1.0~3.0µm in length and 0.8~1.0µm in width. The optimum temperature for growth of the organism is 30~35°C. The optimum pH for growth is 7.0~7.2. Strain SRB-A can use sodium lactate, sodium citrate, sodium acetate, ethanol and acetone as electronic acceptor but can not use glycerol, glucose, sucrose and sodium oxatate. The isolated strain reduces sulfate, sulfide, sulfur, DSMO and FeCl3, then nitrate and nitrite can not be used. The strain has higher tolerance of NaCl, and the optimum growth occurs in the presence of 5%~8% (w/v) NaCl. The result of 16S rDNA sequence analysis indicates that the isolated strain SRB-A is the most similar to Desulfo-vibrio halophilus, and the level of the similarity was 98.4%. The isolated strain has a stronger ability to reduce sulfate, and the level of sulfate reduction reaches about 90% at pH 7 in the liquid medium. 0.6 to 0.8 is the optimum COD/SO42- in the medium for the isolated strain to show better ability to reduce sulfate. At pH 2.5 the level of removal of Cu2+ reaches 96.3%. Under the condition of pH 3.5, the level of removal of Zn2+ reaches 92.6%. When the value of pH reaches about 7, the Fe3+ is precipitated by the formation of Fe(OH)3, and Fe3+ is removed up to 89.4% at last.

Jan 1, 2014

By D. Y. Liang

Rare metal ores have those features of high industrial value and bad performance in ore separation. Most of rare metals ores are with low grade of valuable components, rareness of useful minerals, complicated combination of associated minerals and high difficulty in separation and enrichment of minerals. For those single (Ta, Nb) or (Ta, Nb, Sn) ore occurred in granite and pegmatite, the ways of gravity separation and magneto electric separation to concentrate (Ta, Nb) minerals are adopted. There are many mines being explored successfully both at home and aboard. While, for complex (Nb-Zr-REE) ores associated with Be and Ti minerals, they are commonly considered as rich rare metals ore but more difficult to process. One of rare metals mine in Inner Mongolia has the features as with large reserves and high grade of columbium and zirconium and accompanies with REE and beryllium, therefore with significant industrial value. After the utilization of research method of process mineralogy, detailed mineralogy research has been made on the rare metals ore. The test results show that there are abroad isomorphism replacements among such elements, such as Ti, Mn, Fe, Nb and Ta, between Be and REE in metallic oxide minerals of that ore, which makes the mineral composition of that ore extremely complicated. This research identifies clearly the mineral composition, and investigate at the technological property and the occurrence of those elements as Nb, Zr, Be and REE in the rare metal ore. The achievements of this research provide important mineralogy basis for ore dressing research of refractory rare metallic ores.

Jan 1, 2014

By Heramb M. Bal

This paper will underpin the future development of intellectuals having greater understanding of patent law and legislation, IP rights, and innovation. To understand this idea, I present a case study of China?s progress in the last 31 years in the rare earth research, innovation, and simultaneously patents area. Rare earth elements (REE) are at the centre of high technology and are the next wave of world innovation. Much of modern society depends on rare earth elements through their use in computers, lasers, telecommunications, iPods, medical technology, military applications, and so on (Long et al, 2010). The rare earth research, a large research body is being provided by Chinese sources. China devoted three or four university centers to the study of rare earths (Lifton, 2009). These measures are all designed to keep China at the forefront of REE production, materials, technology, and innovation. As a result in the last fifteen years there has been a shift from a US-dominated REE industry patents to Chinese patents. The world must identify strategic areas of rare earth innovation and provide funding to firms and universities that conduct such research. Not only research and innovation is vital but filing patents and preserving IP rights for research and innovation is even more important. We (rest of the world) need a comprehensive strategy to guide the development of patent and IP rights for research and innovation. To achieve this, the development of intellectuals with superior knowledge of patents and IP rights are the future need of minerals industry. Keywords: innovation, rare earth, patent, IP rights

Sep 1, 2012

By Ali Dehghani Ahmadabadi

Gravity separation technique is widely used in mineral beneficiation practices for its low cost, ease of operation, and eco-friendly nature. The most commonly used gravity methods for beneficiation of iron ores are shaking table, jig and spiral methods which aren&apos;t very effective for iron mineral fines. Multi-Gravity Separator (MGS) is suitable for the treatment of fines with a maximum particle size of approximately 500 µm. This study was performed on a low-grade haematite iron ore from Chadormalutailing dams. Detailed mineralogical, physical and chemical characteristics of a goethiticlateritic iron ore showed that the sample contained porous and friable oxides and hydroxides of iron. The ore sample had a feed grade of 35% Fe, 1.1% FeO, 15.5% SiO2 and 8.5% Al2O3. Haematite and goethite are the main iron-bearing minerals while quartzite and kaolinite are the major gangue mineral constituents. In this paper, the statistical evaluation and optimization of grade and recovery using a factorial design of experiment (DOE) method has been carried out for Chadormalulow grade ultra-fine haematite tailings with MGS. The input process parameters considered are drum speed, tilt angle, wash water flow rate and pulp density. The results show considerable improvements in both the quality characteristics such as grade and recovery with statistical evaluation and optimization, compared to the initial value of grade and recovery. Keywords: multi-gravity separator, mgs, statistical evaluation, optimization, haematite

Sep 1, 2012

By A. Ekrem Yüce, Gülay Bulut, Feridun Boylu, Vecihi Gürkan, Istanbul Technical University, H. MustafaTarkan

"Nickel sulphide ores subjected to this investigation were taken from Orhaneli district where widespread chromite mineralisation can be occurred. Significant amounts of magnetite and chromite have been existed in the ore together with sulphide and oxide type nickel minerals. Ore sample is constituted about 70% magnetite, 15% sulphide minerals, 5% chromite and iron oxides as well as 10% gangue minerals.According to the chemical analysis results, the representative ore sample contains 1.32% Ni, 10.8% SiO2, 78.4% Fe2O3, 1.3 g/t Ag and 1.0 g/t Au. Mineralogical examinations showed that pentlandite (Fe, Ni)9S8, violarite (Ni, Fe)3S4, millerite NiS and asbolane (Co, Ni)MnO2.(OH)2.1-2H2O were the main nickel minerals and magnetite, chromite, chromium spinals, pyrite, pyrhotite, chalcopyrite, cubanite, goethite, hematite, limonite, rutile, chlorite, talc and serpentine group minerals as associated minerals.The aim of this investigation was to produce valuable nickel concentrates by using gravity separation, magnetic separation and flotation methods. As a results of laboratory scale studies, alternative flow sheets for the production of nickel sulphide concentrate were developed. The related experimental results are given in Table 1."

Jan 1, 2003

By Ashok Kumar, Subhadra Sen Dr. Rashmi Kumari, D. P. Chakraborty, Ajay kumar Gupta

The blast furnace coke quality depends on the characteristics of coal blend, pre-carbonization techniques adopted such as stamping, vibro-compaction etc., and coking conditions. Of the above, coal blend plays a significant role in the production of quality coke. Furthermore, the quality of the blend depends on the quality of individual coals and their interaction making up the blend. During transportation and stockpiling, coal is in contact with air for periods of time that sometimes may exceed several months. During this time, reaction with oxygen in the presence of water, sunlight and possibly elevated temperatures may take place. The resulting weathered coal suffers some alteration in its technological properties, which in turn affects coke quality for Blast Furnace operation adversely. In this work, two coals belong two prime hard coking and hard coking categories, namely Illawarra & Tahmoor, were selected and kept in a separate stock pile for a period of 120 days. These coals were characterized in terms of proximate, rheological & petrography properties at a regular frequency. This report summarizes the impact of weathering on the coking behaviour of these two coals in terms of properties as mentioned above. However, the rate of loss depends on coal rank and storage conditions. This has been seen through this study that the loss depends on coal rank and storage conditions. Deterioration of rheological and petrographic properties were seen higher for low-rank coals, like in this study Tahmoor, which is a low rank coal, compared to Illawarra showed higher degree of coking property degradation within the same time period under identical environmental conditions. Low-rank coal deteriorates at a faster rate because low-rank coal is dominated by free radicals that easily react with oxygen, resulting in the creation of various carbonyl groups and weathered vitrinite. Based on the results obtained in this study, size of stock piles for different qualities of coals to be maintained, at a specific time, can be determined and recommended, so that target coke quality is always achieved.

Jan 1, 2018

By B. Peszko

There are many measuring methods of grain sizes. Taking into consideration the fine grained materials, one of the existing techniques is measurement of grain size by the Coulter Counter method. This method is based on the measuring the changes of electrolyte resistance during grains flow through the calibrated diaphragm. This method is relatively simple to apply, significantly precise and the results are given quickly. However, the problem is that the measurements are limited by the size of diaphragm. Because of this situation, measurement of grain sizes by this instrument is possible in range from 10% to 60% of diaphragm diameter. This limitation causes the necessity of re-placing diaphragm in case when the measured grain size distribution concerns the material of large size range. In purpose of determining the total grain size distribution, the synthesis of some partial distributions, given for individual grain fractions (with different diaphragm applied), is required. This is possible to do by calculating the mixture of distribution functions, created from the partial distribution functions. Two materials were selected to research: quartzite and glass, which were comminuted in cylindrical crusher, additionally grinded, screened and then analyzed by Coulter Counter for five grain fractions: 0~125 µm, 0~80 µm, 0~56 µm, 0~40 µm and 0~25 µm. For each fraction, five different partial distributions were given (in case of glass ? four), which are the basis for the creating the joined grain composition. To assure the adequacy of the given distribution function, it is necessary to obtain the possibly best approximation of partial distributions. In the work, both the parametric and non-parametric methods of density approximations of investigated random variable. For each grain fraction the approximations were done by three traditional distribution functions: RRB, GSA and log-norm distribution functions and three methods of non-parametric approximation: Gauss kernel, Epanechnikov kernel and orthogonal Fourier series method. As the criterion of the certain distribution function acceptance, the value of the residual deviation was assumed, given by the formulae:

Jan 1, 2014

By N. I. Tyushkova

This is a brief survey of the technological solutions for deep cleaning of baddeleyite?s concen-trate. Baddeleyite is part of kamaphorite of composite apatite-magnetite ore in alkaline-ultrabasic mountain range of Kola Peninsula. Baddeleyite?s concentrate, which is being produced by Kovdorsky GOK (ore mining and processing enterprise) contains 97.5%~98.5% (Zr?2 + ?f?2) and also scandium oxide (0.05%). It is usually used without any chemical processing. World demand for zirconium oxide is constantly on the rise. Its consumption grows in ceramic industry and in high-tech spheres. That?s why the demand for its purity is very important nowadays (additional cleaning from phosphorus, silicon, iron, aluminium). The mechanism and kinetics of interaction of activated bad-deleyite with sulphuric acid has been studied as well. While applying method of mathematical mod-eling it was confirmed that the mechanical activation is effective for the intensification of sulphation process of baddeleyite?s concentrate with the aim of purifying it from dirt. The use of the calculated optimal regimes allows to reduce such technological operation factors as: temperature, the du-ration of process, the sulphuric acid consumption. It also allows to determine the conditions of anticipatory abstraction of scandium and main dirt in solution in comparison with zirconium oxide.

Jan 1, 2014

By I. Grigoryeva, G. Voiloshnikov, V. Dementyev, N. Moskaeva, N. Voiloshnikova

"Adsorption processes with use of anion exchange resins are widely applied in the gold mining industry of Russia and the former Soviet Union. Anion exchange resin AM-2B and its analogs (with mixed basicity) are used as adsorbents. This paper focuses on the study of weak base anion exchange resin and its comparison with AM-2B resin. Different nature of the ion exchange groups of the adsorbents mentioned above provides essential differences in their properties both during adsorption and elution of gold and silver. Multistage gold elution and resin regeneration procedure is used for AM-2B resin whereas alkaline cyanide solution is used for weak base resin and allows for the reduction Capex and Opex in comparison with AM-2B resin. Anion exchange resins AM-2B and PuroGold S-992 were tested. Weak base resin is sensitive to pH of adsorption medium. Optimal pH value is 10.1-10.3 (at ?? >10.5 gold loading onto resin decreases dramatically). Adsorption isotherms for gold, silver, nonferrous metals, cyanide and thiocyanate ions from synthetic individual metal cyanide solutions were defined. Adsorption of all components onto PuroGold resin was lower than for ??-2? resin. Adsorption of metals from the solution with equal molar metal concentration (0.1 mg-equivalent/L of each metal) was also studied. The affinity of resins to cyanide metals complexes was established. Weak base resin has higher selectivity to gold in comparison with ??-2B resin and is less sensitive to ion composition of cyanide solution or pulp treated. Weak base resin was tested for gold recovery from gold ores. On the base of test results it was recommended to introduce this resin at some new plants in Russia. Commissioning and operation performance of gold plants confirmed efficiency of weak base resin use."

Jan 1, 2014

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Grinding is one of the most energy consuming unit operations and is also a very inefficient and costly process. Therefore, it is of great importance to run the grinding process as efficiently as possible. The most common way today to control grinding processes is by measuring the power draw of the mill and try to keep it at a maximum level. However, some studies (Kawatra, 1989, Koivistoinen, 1989, Moys, 1989) have shown that this measurement doesn.t reflect everything that takes place inside a mill. Among other parameters like slurry rheology, temperature and charge behaviour, the volumetric filling of a grinding mill seems to have a large influence on the grinding efficiency (Herbst, 1988, Koivistoinen, 1992, Vermeulen, 1988). A problem in attempting to measure those parameters has been to get a sensor that is both robust and sensitive enough for continuous on-line measurement.This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a DEM modelling technique is used.The results indicate that the system is capable of following the normal variation that occurs in the mill. The signal also very well reflect changes in operating variables such as ball charge level, pulp density and rotational speed. By studying the nature and different features of the signal one can get a better understanding of milling circuit dynamics. Another feature of the technique is the possibility for an operator to continuously follow the grinding process and thereby run the process under optimal conditions."

Jan 1, 2003