Search Documents

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered

Jan 1, 2014

By M. Kargar Razi

According to the unique properties and many applications of nano silver powder, it was prepared from acid leaching tail solution. The low value residual gold and silver ions were occurred with fellow heavy metals as pollutants (Fe2+, Cu 2+and Zn2+) in acid leaching tail solution in Mouteh gold mine in Iran. Preparation of nano silver particles was achieved in two steps: first, by addition of ammonia as separation step and second by using different reagents as precipitation and extraction steps. Different controlled parameters were including pH, residence time and temperature, mixing time, and reducing reagents to metals molar ratio. Acid leaching process was carried out with sulphuric and nitric acid via suitable reductants. In order to remove copper, zinc, and silver ions from solution, all of the conditions were controlled. The optimum conditions for preparation of nano silver powder with less than 90 nm were pH 10.5, hydrazine/methanol to silver molar ratio of 3 to 4, and reduction time of 5 min in 45 °C. The results were evaluated via SEM, A.A and UV- Vis spectroscopy analytical methods.

Jan 1, 2014

By Z. C. Shen

As core part of flotation column, aerator has been always priority research. A new type of porous aerator made of stainless sintered microcellular material is designed , which diameter is between 20µm to 40µm. High bubble surface area flux is obtained at low air pressure 20kPa by this type of aerator in water. In order to extend its applied range ,experiments were carried out in alkali slurry (pH=12) , resulting with porous aerator clogged after working 20 days . Sampling the cross-section of aerator detected by microscope and X-ray diffraction ,the reason clogging was found. Then plugging aerator was reactivated after putting it in acidic liquor treated by ultrasonic for about ten minutes. On-line aerator maintenance can be done in no down time , and it can be repetitive-used after recovered ,so reduced capital costs.

Jan 1, 2014

New technology for on-line particle size analysis of mineral slurries has opened up new applications for particle size measurement. In some cases the particle size distribution of the final concentrate is an important quality issue. This paper discusses established on-line particle size analysis technologies and presents experiences on the use of a new technique employing laser diffraction in several minerals processing operations. The main innovations in the new instrument are a simple dilution system and multiple scattering correction algorithm, which allows wide solids content variations of diluted sample in the measurement cell. Representative sample for laser measurement is produced by a simple and reliable dilution system. The applications discussed are; Blaine number measurement of Fe concentrate before pelletizing, grinding of variable batches of ore and paste thickener control.

Jan 1, 2014

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

By D. W. Feng

Thiosulfate as an alternative lixiviant for gold has received much attention in recent years due to the growing environmental concerns over the use of cyanide. Cu(II) is used to catalyze the oxidation of gold and ammonia is to stabilize Cu(II) in alkaline solution. However, the presence of Cu(II) enhances the oxidative degradation of thiosulfate. The high consumption of reagents has made thiosulfate leaching uneconomical to date, in comparison with cyanide leaching. Therefore, further investigations are required to leaching under low reagent concentrations over extended periods where reagent consumption is low and gold leaching rate is low as well. It is thus necessary to find additives to enhance gold dissolution in the thiosulfate leaching system. Electrochemical studies using rotating gold disc showed that the oxidation of gold in ammoniacal thiosulfate solution increased significantly in the presence of a small amount of thiourea and the beneficial effect increased with an increase in the thiourea concentration up to 7.2 mM. Thiourea improved gold extraction in the thiosulfate leaching of gold from a sulfide ore under low reagent concentrations. Excessive addition of thiourea inhibited the leaching of the gold ore. The decomposition of thiosulfate was reduced with the presence of thiourea. X-ray Photoelectron Spectroscopy (XPS) results indicated that thiou-rea likely decomposed to sulfide and formed gold sulfide species at the gold surface.

Jan 1, 2014

By Kumar Ranjan, Kumari A. V. Asha, G. E. Sreedhar, Banerjee R. Raja, M. Narasimha, R. Shivakumar

In this paper, numerical simulation of magnetite, medium segregation and coal partitioning have been made in a 350 mm diameter cyclone. An attempt is made to assess the nature of impairment in efficiency in relation to the increasing amount of near gravity materials in coal. The CFD model approaches the Algebraic Mixture (ASM) model with the granular option and Reynolds stress model (RSM) to resolve the air core and turbulent mixing of the medium and coal particles. The partition characteristics of the DMC were modelled using both Lagrangian & Eulerian particle tracking for particles ranging in size from 0.5 to 8 mm and in density from 1200 to 2000 kg.m-3. Lagrangian frame work based Discrete Phase model used to simulate the coal particle trajectories inside the DMC and attempted to understand the residence time of different size and density coal particles. It was observed that coal particles having density near to separation-density (having fifty percent of probability to under flow and overflow) are exhibiting increased residence time than any density particles. As expected the smaller size coal particles shows higher residence time than the coarse coal particles. CFD simulations on effect of NGM mass fraction are simulated and analyzed using ASM model including for coal and magnetite. Coal particles with high NGM content show significant effect in misplacement of coal particles towards wrong products at all relative densities. The residence time of the particles increases because of its increased interaction with near dense particles. The effect of NGM fraction on overall cyclone performance as well as detailed flow assessment in terms of residence time distribution, NGM particle concentration profiles with respect to LZVV is presented.

Jan 1, 2018

By Masakazu Niinae, Kenji Aoki

"Electrokinetic soil remediation by electroosmosis and ionic migration is restricted to soluble substances. At a higher pH, the soil particles sorb more heavy metals than at a lower pH and the precipitation of heavy metals are promoted. Both mechanisms make heavy metals immobile, rendering cleanup more difficult and electrokinetic extraction inefficient.In this study, the effectiveness of introducing a complexing agent to enhance the removal of cadmium from kaolinite in the region of neutral pH by ionic migration is examined. The complexing agent selected was ethylenediaminetetraacetic acid (EDTA). The investigation was carried out in a laboratory-scale column containing kaolinite contaminated with cadmium. As the results of the study, cadmium migrates toward the anode without accumulation of cadmium and is successfully removed at the anode reservoir."

Jan 1, 2003

By A. Morrison, P. Brito-Parada

"The separation of valuable and gangue minerals according to their surface hydrophobicity in a froth flotation tank occurs in both its pulp and froth phases. In the pulp phase, hydrophobic particles must be brought into contact with rising bubbles introduced at or near the bottom of the tank. In a mechanical froth flotation tank, this is primarily achieved through the agitation of the pulp by an impeller or by a rotor-stator system. However, the turbulent and mixing effects of such an impeller or rotor-stator system, necessary to promote bubble-particle interactions in the pulp, are not confined to the pulp zone, but are transmitted into the froth zone at the pulp-froth interface. This impeller-induced turbulence at the pulp-froth interface is compounded by the impulse of buoyant bubbles entering the base of the froth phase, reducing the stability, and thus separation performance, of the resulting froth. Hence, turbulence improves separation performance if it occurs deep in the pulp phase, but diminishes it if it occurs close to the pulp-froth interface. For this work, a performance-enhancing pulp phase insert was designed to isolate the impeller-induced turbulence from the pulp-froth interface in a laboratory-scale, continuously-operated froth flotation tank. The result was a shifted grade-recovery curve that allows the insert to be designed to maximize the recovery from the system without sacrificing the grade of the concentrate, or vice versa, along a spectrum of improved performance. This paper will present the insert design and development process that resulted in this improved grade-recovery curve, as well as a set of heuristics that could be used to design a similar insert for pilotand industrial-scale validation and deployment.INTRODUCTIONAn almost ubiquitous design feature of commercial flotation tanks is the enclosure of the impeller to create a concentrated turbulent zone (Mavros, 1992). These turbulent zone enclosures are varied-- from the rotor-stator design of, for instance, Outotec cells, to the air disperser design of Wemco cells-- but all share the same rationale: that turbulence is desirable to promote bubble-particle interactions (Ralston, 1999), and to produce smaller bubbles (Wills, 2006), but also undesirable because it promotes the detachment of valuable mineral particles from bubbles, and exacerbates entrainment-inducing mixing at the pulp-froth interface (Jameson, 2010)."

Jan 1, 2018

By S. Dwarapudi

Pelletizing of Indian chromite ores is more challenging due to their high refractory nature. High Cr/Fe ratio and high MgO content in these ores demand high firing temperatures and longer firing cycles but often result in low strength fired pellets. Aim of this study was to develop cold bonded chromite pellets for smelting in submerged arc furnace (SAF) from chromite fines using suitable binder that induce less gangue into the pellets but cures quickly. Different binders were studied through laboratory pelletizing experiments for their suitability for cold bonding the pellets. As result, a composite binder comprising organic and inorganic binding agents was found to be suitable and pellets made from the same were tested for their low and high temperature behavior. High temperature reduction studies revealed that pellets were resistant to disintegration up to 1200 °C.

Sep 1, 2012

By Shobha Kumari

Coal is the prime source of energy in India. It now contributes to about 55% of the total power generation and will continue to have its major share in the energy mix of the country in the foreseeable future. Thermal coals of India, known for their wide variations in nature and categorized as difficult to wash due to their typical mineral matter association with the organic matrix, need suitable beneficiation technique for quality upgrade for improving the overall economics, efficiency and pollution free power generation. A non-coking high-ash coal, collected from Vasundhara open cast mine of the Ib Valley Coalfield, Orissa, has been characterized along with its different fractions obtained in the process of beneficiation for distribution of minerals using FTIR, XRD and ash analysis. The raw coal was fractionated by size as well as by density. It has been observed that ash yields and mineralogical composition (found to be mainly kaolinite and quartz) have no appreciable change in different size fractions, indicating homogeneous distribution of minerals in the coal matrix. However, for the different density fractions the mineral composition and ash yield have significant variations. The quartz content of the beneficiated coal visualized with 34% ash yield, as mandated by the Ministry of Environment and Forest (MOEF) for the use of coal in power plants is reduced to half of that of the raw coal. As quartz is the most abrasive mineral in coal, reduction of its proportion obviously signifies considerable reduction of wear of power plant machinery when beneficiated coal is fed to utility boiler for generation of power. The composition of the major minerals quartz and kaolinite as determined, also favors formation of ash of refractory nature during combustion. Keywords: IB valley coal, beneficiation characteristics,

Sep 1, 2012

By Nidhi Kumari

This work is based on surface chemical properties of bacteria during adaptation to high grade copper minerals and the projected consequences in Bio-Flotation process. The utility of bio-processing in the beneficiation of copper ore through bio-flotation is demonstrated. An autotroph Acidithiobacillus Ferrooxidans bacterium is adapted to high grade mixed copper ore sample by repeated subcultures. The surface characteristics were studies by analyses at different pH and time intervals. From the studies, it was established that the mineral-adapted cells became more hydrophobic as compared to unadapted cells during bio-flotation. It was also noticed that there was no significant changes in the surface charge of bacteria before and after adaptation. Keywords: bio-flotation, copper, Acidithiobacillus ferrooxidans, hydrophobic

Sep 1, 2012

By V. F. Petrov

Today, sodium cyanide is extensively used for extracting gold, however it is highly toxic to the environment if not managed properly. This paper discusses the key challenges presented to gold operations in efforts to come into alignment with the Russian environmental regulations and suggests solutions to overcome these challenges. It is a fact that the major environmental threat cyanide poses to water sources. Therefore, natural water sources should be well protected from the adverse effect of cyanides used in hydrometallurgical processes. For this, the following site procedures and facilities are practiced: in-site and external water recycling systems, reclaim water treatment if required and tailings ponds with water impermeable screens (tailings ponds with controlled leakage). Cost comparison analysis of cyanide destruction methods was carried out. It was revealed that the aldehyde treatment method developed by Irgiredmet JSC demonstrated the best economics. Cyanide emissions are treated by mass-manufactured packed and membrane devices which allow to keep cyanides at the acceptable limiting values established by environmental regulatory agencies.

Jan 1, 2014

By R. K. Rath

The low-grade iron ore sample contains both lumps and fines. It is mostly hematitic iron ore and considerable amount of goethitic/limonitic material is present in it. The major impurities present were quartz and clay. It is observed that the iron bearing phases are poorly liberated above 300 µm and the liberation improves below 300 µm. More than 80% liberation is achieved below 106 µm. Based on the liberation data, the feed for the different beneficiation methods was prepared by stage crushed the ROM followed by grinding passing to 106µm and the ground material (-106µm) was deslimed. The underflow was subjected to various beneficiation techniques such as tabling, enhanced gravity separator (EGS), wet high intensity magnetic separation (WHIMS), and flotation and the results are discussed. All the methods studied could able to produce pellet grade concentrate with iron content of 64.5%, however, a marginal higher yield was observed for WHIMS (81%). Keywords: beneficiation, gravity, magnetic, enhanced gravity separation, flotation, low-grade iron ore, desliming

Sep 1, 2012

By Danfeng Xu

The majority of the world?s nickel (Ni) resources occur as laterite ores, which are exceptionally complex, lower grade (<1.5% Ni) and expensive to treat using conventional smelting and high temperature/pressure autoclave methods. Heap leaching is a promising, less costly, alternative technology for processing low grade nickel laterite ores. However, significant technical challenges remain with Nickel laterite heap leaching, preventing its general adoption. This paper presents some highlights of laboratory column leaching studies undertaken to characterise, evaluate and optimise sulphuric acid leaching behaviour of Nickel laterite agglomerates. They provide basic but valuable information regarding Nickel laterite agglomerate structure stability and leaching performance under industrially-relevant, continuous acid irrigation conditions. In particular, Nickel and other key metals? (e.g. Co, Fe, Al and Mn) extraction rates, free acid concentration, bed slump and structural changes were determined at a given acid percolation rate as a function of time. Potential implications of the findings, for devising strategies for improved Nickel laterite plant heap leach operations are discussed. Keywords: nickel laterite, column leaching, agglomerates, leaching kinetics, acid consumption

Sep 1, 2012

By H. Z. Liu

An extra-refractory gold ore in China belongs to Carlin Type Gold Ore which is not only submicroscopic but also rich in arsenic and organic carbon. They have been proved that its floatability is not good enough and the gold in the ore could not be leached almost if it was not pretreated. The tests for the ore were carried out in accordance with flotation-concentrate preoxidation-cyanidation(or CIL) processes in order to exploit the mine. Two new depressants were discovered in the flotation tests and improved concentrate grades from about 20g/t to 32~50g/t. The methods of the concentrate preoxidation tests were alkaline atmospheric oxidation, acidic atmospheric oxidation, acidic pressure oxidation, roasting oxidation?biooxidation. The cyanidation tests after the concentrate preoxidation have proved the gold extraction of the pressure oxidation to be the highest(92.5%) and that of roasting secondary(89.3%). After fuller techno-economic comparison, it is suggested that the flotation-pressure oxidation or roasting-CIL process should be the most optimal for treating the ore. The gold recoveries of the ore were 83% for the pressure oxidation and 80% for the roasting respectively.

Jan 1, 2014

By T. Gong

Often plans to increase plant throughput provide an opportunity for optimising plant equipment and operating methods. This was the case in 2005 at TISCO Jianshan Iron Mine, when an increase in production was planned. The thickening circuit had presented a limitation to the plant throughput and operation with poor overflow clarity and underflow density. Following a course of test work by Outotec, a 53m diameter Supaflo® High Rate Thickener (HRT) was selected for the duty. From early stages of operation of the new thickener, the benefits have been dramatic, including: ? Improved tailings underflow density by 9% ? Improved Overflow clarity to less than 150ppm ? Considerably decreased the water and energy consumption as well as operation cost ? Stable and reliable operation This paper looks at this installation as a case study and compares the previous thickener installa-tion performance with the performance of the single 53m HRT.

Jan 1, 2014

By W. Rubarth

The kaolin losses in hydrocyclone classification are determined by the fines, which are discharged together with the water to the underflow. This paper presents an improved technique of water injection to the conical part of the cyclone applied especially for small cyclones in kaolin preparation. In small hydrocyclones water, injection is a sensitive process. Therefore, the process was stabilized by controlled water injection dependent on the measurement of the underflow shape. Three applications of this innovation are presented. In the first case, the water injection is applied for the separation stage in dilute suspension where the final product is produced in the overflow of a 50mm hydrocyclone. The underflow contains sand and residual kaolin. For a higher kaolin recovery, the underflow is usually treated downstream in washing cyclones. The wash water injection results in a 45 ? 50% - reduction of the kaolin fraction <25µm in the underflow. Thus, water injection to the classifying cyclone leads to a separation comparable with a downstream washing stage. An additional hydrocyclone stage can be deleted. The second application refers to a classification in dense suspension. Here, the underflow of the last hydrocyclone stage was directed to a washing in a 50mm hydrocyclone. The additional injection of 3L/min water in to the conical part of the cyclone reduced the kaolin losses by half.The third application was executed in the washing stage equipped with 75mm hydrocyclones where the underflow is directed to flotation. Using the water injection the kaolin recovery in this stage was increased by approximately 20%. Keywords: hydrocyclone, classification, kaolin beneficiation, water injection, underflow washing

Sep 1, 2012

By Indresan Govender

A continuum based granular flow model of charge motion that combines the inherent frictional nature of particles with its distinctly fluid-like structure is presented. Starting with Newton?s 2nd Law on a volume element of charge, we derive the velocity field in the bed free-surface and the rising en-masse region. Invoking flux conservation within the two regimes of interest then yields a (simple) differential equation for the free-surface of the charge body. Combining the velocity field gradients with a suitable constitutive choice for the shear stress completes the picture with a description of the in-situ rate of shear power dissipation in a tumbling mill ? a mechanistically correct account of power draw in a tumbling mill. Positron Emission Particle Tracking (PEPT) was used to measure the in-situ flow fields of the charge within opaque systems like tumbling mills. The accurate velocity and mass distribution derived from PEPT form the basis for direct verification of the resulting granular flow models. In this regard a wide range of milling conditions is investigated and presented in this paper.

Sep 1, 2012

By A. Vidyadhar

Using pure quartz and hematite minerals, the adsorption mechanism of mixed cationic/anionic reagent schemes was investigated through Hallimond flotation studies. The flotation response of quartz and hematite independently with cationic and anionic collectors as well as with mixed cationic/anionic collector systems is assessed. The flotation response as a function of pH and collector concentration was investigated. The single mineral flotation tests in the presence of anionic collectors, quartz does not respond to flotation, but the C12 amine flotation of quartz was observed to be pH and concentration dependent. It was observed that hematite flotation recovery is maximum at acidic pH with sodium dodecyl sulphate (SDS), neutral pH with oleate, and at basic pH about 9.5 with C12 amine. Flotation results with both quartz and hematite indicate an increased adsorption of cationic collector in the presence of anionic collector apart from its own co-adsorption. The incorporation of oleate in between C12 amine molecules decreases the electrostatic head-head repulsion and thereby increasing the adsorption of C12 amine due to attractive tail-tail hydrophobic bonds, besides forming a closely packed adsorbed layer enhancing the hydrophobicity. The increase in oleate concentration beyond C12 amine concentration leads to the formation of soluble C12 amine-oleate complex / precipitate and the adsorption of these species decreased the flotation since the alkyl chains are in chaotical orientation with a conceivable number of head groups directing towards the solution phase. Keywords: quartz, hematite, adsorption, mixed collector system, flotation, zeta-potential

Sep 1, 2012