Search Documents

By W. H. Cheung

Nickel (Ni) plays a major role in the production of steel and other major alloys. There are two sources of Ni: laterite and sulphide ores. Global reserves of sulphide ores are being rapidly depleted, while there are enormous reserves of Ni laterite, much of it in Australia. As well as being present in huge amounts, Ni laterites have the advantage of containing cobalt (Co), a valuable mineral. Over the past decade, these factors have been driving the industry to explore the processing of Ni laterite. A route that has been used commercially in processing nickel laterite ore involves the thermal activation of the minerals by pre-reduction followed by ammoniacal leaching (Caron). Although this process has been effective in processing the goethite rich laterite minerals, the higher-grade serpentine-based minerals have been shown to be less susceptible to this process. This has been attributed to the formation of inert olivine phases. In this study, we examined the use of an alternative lixiviant, sulphuric acid, in leaching pre-reduced limonite and weathered saprolite nickel laterite ores. The specific aim of this study was to examine the sulphuric acid leaching of Ni and Co from pre-reduced laterite minerals, and to understand the role of mineral transformations in this metal dissolution. Synchrotron based X-ray diffraction was used to examine the transformation of goethite (FeOOH) to spinels and serpentine mineral ((Mg,Fe)3Si2O5(OH)4) to olivine. Reduction tests were carried out using CO and CO2 reducing gas mixtures and temperatures from 400 °C to 700 °C. The rate of formation and disappearance of specific Bragg peaks during reduction of specific minerals were used to derive an understanding of these solid-state reactions. Laboratory based reduction tests and leaching in sulphuric acid were used to validate the effect of these mineral transformations. The results suggest the versatility of sulphuric acid in leaching nickel from spinels and olivine, which was achieved at the expense of lower selectivity. Cobalt dissolution was found to be dependent on the nature of ferro-cobalt alloy formed during reduction.

Jan 1, 2014

By Jerzy A. Mielczarski

The separation of albites from quartz by flotation applying the conventional HF-methods is no longer acceptable from an environmental and health point of view. Therefore, the search for a new reagent scheme without using HF depressor for separation of albite from quartz is under consideration. The flotation behaviour of ore mineral components depends on the produced hydrophobic or hydrophilic surface coverage (chemical functionalization). Currently we have excellent possibility of monitoring surface composition and structure at molecular and atomic levels at surfaces of natural minerals contacted with aqueous solutions of collectors, activators, depressants which is vitally important for the understanding of the surface chemistry that govern selective and efficient flotation. Detailed surface characterization of minerals before and after their exposition to different solution conditions was performed by the most modern spectroscopic techniques such as developed by us the infrared external reflection technique combined with spectral simulation and X-ray photoelectron spectroscopy (XPS). It is possible to monitor surface reactions which facilitate the separation process and those which bring disadvantage to selective flotation. At first we found that a small amount of ?mineral impurity? presented in natural ore could play important role in selective hydrophobization process. It was found that the pH of solution (parameter possible to control) and natural mineral impurities present in mineral samples (parameter related to ore origin) play a very important role in the separation process. Another important parameter is interaction between minerals, quartz and albite, present in aqueous solution. The limitation of flotation separation resulting from chemistry will be discussed. Moreover, the most promising scheme for separation of albites from quartz will be examined.

Jan 1, 2014

By K. C. Corin, M. S. Manono, R. M. Manenzhe, J. G. Wiese

"Environmental concerns necessitate the recycling of process water within mining operations. Given that recycled water is chemically different from fresh water, and collectors are added such that they adsorb at the liquid-particle interface, changes in the aqueous phase are expected to affect collector adsorption. A Finnish nickel-copper ore was floated in synthetic plant waters of varying ionic strengths and plant waters obtained at Boliden Kevitsa Mine, with aerophine and sodium isopropyl xanthate as collectors. Of the tested waters, the copper thickener overflow was the least conducive to xanthate adsorption and valuable mineral recovery. The nickel thickener overflow, standard process water, and raw water were the most conducive to xanthate adsorption. For the raw water and nickel thickener overflow, increased adsorption correlated with increased valuable mineral recovery. Further, recycling xanthate retained in water affected the selectivity of the collector and hence the concentrate grades.INTRODUCTIONFlotation is a separation process that exploits the differences in the surface properties of the particles being separated. The efficiency of separation is dependent on the degree of hydrophobicity achieved by the particles meant to be floated, which are, in most cases, valuable minerals. The hydrophobicity is in turn dependent on the adsorption of the chosen collector onto the surfaces of the floated particles (Fuerstenau, 1984; Taggart and Hassialis, 1946). Empirical findings suggest that species dissolved in solution strongly influence collector adsorption and overall flotation response (Fuerstenau and Chander, 1986). Due to environmental concerns, it is becoming more pertinent for mining plants to recycle process water and hence limit the usage of potable water. There is an interest to ensure minimal discharge of plant water into the environment, as this water is typically polluted with process reagents that may render it toxic (Levay et al., 2001)."

Jan 1, 2018

By T. C. Alex

Mechanical activation of gibbsite [?-Al(OH)3] is the theme of this paper. Industrially prepared gibbsite used in the study has a mono modal size distribution with a median size, d50=110 µm. Mechanical activation of this gibbsite has been carried out in a planetary mill at ambient conditions. Mechanical activated gibbsite samples are characterised in terms of particulate characteristics, structural characteristics and reactivity. As a result, of milling, mono modal size distribution of the unmilled gibbsite changes to a broad multimodal distribution. Size reduction has been sharp in the initial stages of milling; median size reduces to ~7 µm during 15 min of milling. Thereafter no decrease in median size is observed; rather it is found to increase gradually with further increase in milling time, indicating particle aggregation. Morphological studies of milled gibbsite have shown that the platelets forming the agglomerate are separated first; the separated platelets then undergo breakage. Aggregation of particles sets in the later stages of milling as a result of increased surface area and surface energy. X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies have clearly revealed the changes in gibbsite structure during milling. Analyses of XRD data show that the crystallite size of gibbsite decreases as the milling time progresses whereas its microstrain is found to increase. Accumulation of energy in the structure is the result in both cases. TEM micrographs with signs of defects leading to disordering of gibbsite structure complement the XRD results. Reactivity of milled gibbsite, decrease in its deydroxylation temperature and increase in alkali dissolution, is found to increase with mechanical activation. Increased reactivity of milled gibbsite is found to have a strong correlation with the BET specific surface area. Keywords: mechanical activation, gibbsite, alkali dissolution, thermal dehydroxylation, reactivity

Sep 1, 2012

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By Robin B. Batterham

"Since the 1970?s we have seen a marked corporate response in terms of the environment. In part this has come from regulation but it has largely come from stakeholders and the community. Rising expectations have in general been met. We now see a similar trend towards sustainability. At the same time, the importance of mining to the share market has decreased drastically and with that decrease has come the requirement for the mining sector to show returns similar in manner to other sectors. While rationalisation can achieve some progress towards these goals, the long-term requirement is for innovation, as it always has been. This paper looks to the logical goal of innovation within a sustainable mining framework and targets the removal of the desired metal values with minimal environmental footprint. It is suggested that broad ranging alliances will be necessary, particularly amongst the R&D suppliers, to achieve this goal. Industry will need to take an active role given the recent global restructuring.THE MARCH TO SUSTAINABILITYSince the 1970?s there has been an increasing corporate response on environmental matters. We have moved from matters environmental being issues relevant only to minority groups through a series of attitudinal changes by management. Whilst there have always been examples of excellent environmental performance, for many in the 70?s spending money on improving the environment beyond some minimal level was seen as a distraction from production or treated in a similar way to donations to the community. There is little of that attitude these days, as most mining companies have long since regarded the environment as a core business direction. Indeed, for some years one could note an escalation in matters of environmental reporting to the extent that the environmental performance of companies is now very public. In some cases, NGOs have even been invited to help certify and audit the reporting standards. Similarly with health & safety.There is now a rising expectation on the part of the community that social matters will also be given the same level of support as health, safety and the environment. This time around it would appear that the mining industry is at the leading edge of sustainability. The Global Mining Initiative (Global Mining, 2002) and the contributions to the Rio World Summit on Sustainable Development (Rio +10, 2002) suggest that sustainability is being taken very seriously by the mining industry. For sustainability it is convenient to use the Brundtland (1987) definition. This definition has widespread acceptance with governments, industry, environmental groups, financial institutions and individuals as a direction against which our activities and plans can be measured."

Jan 1, 2003

By C. A. Acuña

Extensive literature exists on the motion of single bubbles and the behaviour of swarms of bubbles. This contribution describes work to track and reveal the motion of individual bubbles in a swarm. The technique is based on high speed cinematography and tracking of multiple moving objects. Image processing algorithms were implemented in Matlab to isolate and measure geometric proper-ties of the bubbles in image sequences recorded at 2 ms interval; and these properties were compiled into a data structure. To track a bubble, the geometric properties and a matching criterion were applied on consecutive pictures to identify the bubble. The bubble trajectory was reconstructed from the data structure for the matched objects. The methodology is briefly described. The new technique was tested for bubbles produced at slot-type spargers (i.e., approximately 2-D swarms) in the presence of two frother types ('strong' and 'weak'). Two observations are discussed: a) that bubble motion in a swarm describes a velocity-size relationship dictated by the dominant bubble size class; and b) that surfactant type influences bubble rise velocity for bubbles in the range 0.1 mm to 4 mm. The latter suggests surface viscosity rather than surface immobilization determines bubble rise velocity.

Jan 1, 2014

By N. Tsoni

The separation and recovery of fine and ultra-fine particles during the processing of mineral commodities by conventional separation methods is difficult and inefficient. This is due to the problems posed by the very small size of the mineral particles. The fine and ultra-fine mineral particles are either generated during size reduction processes or are necessitated by liberation size. This problem is expected to deteriorate, as deposits of even lower grade are processed. The inefficiency of the conventional separation methods with regards to the processing of very fine particles leads to the loss of considerable quantities of mineral commodities to the tailings. Novel methods and techniques as well combinations of known methods have been tested over the years. Among them, selective aggregation, along or in combination with flotation, has been given much attention. This study deals with the application of hydrophobic agglomeration as a separation method for very fine particles. The selected mineral system is magnesite/quartz, due to its sensitivity to physi-cochemical separation methods. The aim was the selective agglomeration of magnesite using sodium oleate. Tests on single minerals revealed that separation seems feasible and efficient. The parameters examined were: pH, quantity of sodium oleate, conditioning time, and, finally, settling time. Tests carried out on artificial mixtures of the two minerals, under various proportions, confirmed the results obtained from single mineral tests but they were slightly inferior. Finally, hydrophobic ag-glomeration tests were carried out on single and artificial mixtures of minerals using sodium oleate and petroleum as reagents. The results show that the addition of petroleum improves the results. In conclusion, hydrophobic agglomeration can be applied successfully even for fine particles of difficult-to-be-separated systems such as magnesite and quartz.

Jan 1, 2014

By Fu Ping-Hao, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton’s Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003

By Gaom M. W.

The Mount Isa copper concentrator started operation in 1973. Its secondary grinding circuit consisted of two 5 meters diameter ball mills in closed circuit with 505 mm cyclones. At the design throughput of 800 t/h, the 80% passing size of the circuit product (P80) was about 140 µm. The then Mount Isa Mines Limited (?MIM?) installed two autogenous grinding (?AG?) mills in 1991 to replace two stages of crushing, a rod milling stage and one primary ball milling stage. One of the AG mills was later converted to semi-autogenous grinding (?SAG?) operation by the addition of a steel grinding medium to achieve the designed plant throughput of 800 t/h. The cyclone over-flow P80of the secondary ball mill circuit was reduced to 120 µm by the increased operating power in the AG/SAG mill circuits. The two secondary balls mills had a grinding power of 5.2 MW. A mineralogical study of the milled products indicated that half of this grinding power was sufficient for adequate chalcopyrite liberation. Eliminating one of the secondary ball mills could reduce energy and operating costs by more than A$2 million dollars per year. An optimisation project team was established to achieve the predicted power saving. Grinding circuit simulations were conducted for different circuit configurations. Ball mill parameters such as ball size, ball charge and feed slurry density were optimised. Cyclone body diameter, spigot and vortex finder sizes, and cyclone types were tested. The secondary ball mill circuit was redesigned and several proposed circuits were run as trial production campaigns to determine their operability and efficiency. The plant trials confirmed that one of the secondary ball mills could be decommissioned. Significant cost savings were achieved as a result. The success of the project demonstrates optimising grinding circuits can not only deliver the plant performance, but also a much lower unit operating cost through energy and maintenance savings.

Jan 1, 2014

By A. Erdem

In this study, approximately 3 tons of coal sample taken from thickener entrance was prepared by mineral processing techniques and cleaned by gravity methods. The samples were classified to 5 size fractions by wet screening. The size fractions of +1mm and -1 +0.500 mm were chosen for direct consumption or cleaning by spirals. The studies by Multi Gravity Separator (MGS) were carried out with the -0.500 +0.280 mm and -0.280 +0.020 mm size fractions where the -0.020 mm fraction does not used in the experiments. The clean coal fractions of +1 mm and -1 +0.500 mm obtained by classification were subjected to lower calorific value (LCV), ash and total sulphur analyses. The results were 4168-4946 kcal/kg (on dry basis), 31.01-38.54 % ash and 4-4.27 % total sulphur content respectively. The results of the clean coal concentrated by MGS experiments in -0.500 +0.280 mm fraction was found 5918 kcal/kg LCV, 19.82 % ash content and 80.47 % combustible recovery. The results for the -0.280 +0.020mm fraction were 6004 kcal/kg LCV, 19.19 % ash content, 80.47 % combustible recovery respectively. With reference to the above experimental results, pre-economic evaluation studies were completed and decided to construct an additional unit to the plant. Capacity of the constructed unit is 75.000 t/y which corresponds $ 2.600.000 income in a year. General Directorate of Turkish Coal Enterprises concluded to apply this project to the other coal washing plants in the country due to the successful results of this study and laboratory studies has been going on by MTA currently. Keywords: coal tailings, mgs, recovery, washery, pre-economic evaluation

Sep 1, 2012

By Boris Albijanic, Hongjuan Chen, Bogale Tadesse

"During mechanical flotation of fine liberation sized complex rare earth ores, a large fraction of ultrafine valuable mineral particles are lost to tailings. Fine gangue mineral particles can be entrapped within the froth phase and be floated together with target mineral particles. Another common challenge in ultrafine rare earth mineral flotation is the formation of a sticky froth (excessively stable froth). Thus, the improvement of the flotation of fine and ultrafine rare earth bearing minerals through appropriate cell design and reagent selection is highly desirable. The aim of this study is to investigate the performance of a pico-bubble cavitation flotation column in improving selective recovery of ultrafine rare-earth elements (REEs) bearing minerals from complex and low-grade ores. In pico-bubble cavitation column, very small bubbles are generated which are capable of attaching to ultrafine particles and consequently modifying their surface properties. The overall effect of these processes should lead to improved flotation selectivity and recovery of ultrafine RE mineral particles. In this paper, the effects of a number of flotation operating variables on recovery and grade of REE minerals was investigated using a continuous pilot scale pico-bubble column flotation. At the flotation conditions used in this study, subtle monazite upgrade was observed while gangue Fe oxide was preferentially floated even in the presence of depressants. INTRODUCTION Rare earth elements (REEs) have unique properties such as superconductivity and catalytic activity, and are in high demand for a large number of cutting-edge technologies in the modern world including the production of mobile phones, fuel cells, displays, permanent magnets for wind power generation, high-capacity batteries, green energy devices, etc (Naumov, 2008). REEs tend to be intimately associated within many minerals, and are rarely found in high concentrations in deposits for economic extraction. Up to now, among over 250 minerals containing REEs, bastnasite (Ce), monazite (Ce, Th and La) and xenotime (Y) are the three main minerals that contain sufficient grade of REEs for commercial exploitation (Zhang and Edwards, 2012). The deposits that contain bastnäsite, monazite and xenotime usually have complicated mineral compositions, with various valuable minerals of fine embedded grain sizes in association with complex gangue minerals. In order to ensure liberation of the REEs minerals, fine grinding to less than 30 µm is necessary. This fine grinding leads to difficulty in recovering a large proportion of fine and ultrafine particles in separation processes such as flotation (Trahar and Warren, 1976). Consequently, highly liberated and ultrafine fine valuable REEs particles are lost into tailings during traditional mechanical flotation. Besides, the formation of extremely sticky and stable froth inhibits the drainage of hydrophobic particles. Thus, improving flotation of rare earth bearing minerals, particularly the ultrafine size range, is highly desirable."

Jan 1, 2018

By Pejman Oghazi

During the last decade the output of mining companies has increased rapidly. The key driver is the increase in demand for raw materials in the developing world, and thus this demand has driven up ore prices. From the time when the Raw material group (year 2000) started to introduced their index, it was set to 100 points. Today, year 2011, the index is over 400, which means that ore prices have quadrupled since then. Mine companies have to go deeper in the mines to access the ore bodies to increase the mine capacity and to be able to respond to the market. By going deeper in the mine, there will be new challenges that have to be considered. One of these challenges is how to handle the mine water that is produced in the mine. The water has to be moved to the surface in order to keep the mine from flooding, and this causes more challenges. One solution is to pump the mine water up to the surface without treatment; however, this causes considerable pump wear and the water will still require treatment on the mine?s surface. Another solution is to treat this water in the mine before pumping it to the surface. Metso Minerals has a system solution to treat the mine water, by separating the solids from the mine water. This system reduces the erosion in the pumps and will save many maintenance hours in the long term. One other option is to use the treated water in a closed circuit and reuse it in the process. This system can be divided into three steps: Firstly, a spiral dewaterer to remove the coarse solid particles. For the next step, lamella thickener is used to remove most of the solids, and lastly tube press to handle the sludge from the underflow lamella thickeners. Keywords: mine water, mineral processing, dewatering, separating

Sep 1, 2012

By Ari Kokko

Metso has a long history supplying boilers for high ash coal firing. These boilers are based on circulating fluidized bed (CFB) technology. CFB?s biggest benefit is fuel flexibility ? it can burn fuels from high moisture content to high ash content. Metso has delivered tens of CFB boilers burning waste or high ash coal starting on 80?s. Some of the boilers have been in operation twenty years meaning that there is a long term experience from these plants available. This feedback includes boiler performance and maintenance issues of the boiler. Metso is also delivering coal washing plants to improve coal quality, i.e. reducing ash content of the coal. The idea to combine coal washing plant and CFB boiler was made up two years ago in Metso. Up-coming legislation of coal washing and restrictions for washery reject land-filling in India are good drivers for this kind of concept. Pre-study of this kind of concept led to the conclusion that coal washing process can be fine-tuned so that reject?s calorific value is only 1100 kcal/kg and that was set as a target for boiler design. Metso shipped 200 tons of washery reject to its own research center located in Tampere Finland. First a wide range of fuel characterization tests were done in lab-scale and after that one week test run in 4 MW CFB pilot boiler was done. Test run proved that 1100 kcal/kg can be fired without any support fuel with special boiler design. Test run results gave a good set of data regarding combustion efficiency, emission performance and boiler dynamic behaviour when burning this kind of fuel. These results are introduced in this paper. This paper introduces also the CFB boiler concept for washery reject firing including boiler plant, fuel and ash handling systems and flue gas cleaning system. Power plant can be integrated with coal washing plant so that boiler size matches with washing plants c

Sep 1, 2012

By I. Dymov

"The extractive metallurgy of precious metal ores involves gravity concentration, flotation and cyanide leaching. Pre-oxidation, such as roasting, autoclaving, bacterial oxidation and other techniques, is required for processing refractory ores. Selection of the process is mainly driven by the grade, reserve and mineralogy of the target elements. The concentrations of precious metals in the crust are extremely low and highly variable, resulting in ore variability in many gold, silver and PGE deposits. More importantly, precious metals in an ore may occur in two or three forms (i.e. microscopic, submicroscopic and surface-bound), making ore processing of precious metals extremely challenging. The objective of geometallurgy and process mineralogy is to reduce and minimize the technical risk in project evaluation, process selection, mine planning and production forecasting through geometallurgical modelling, representative sampling and subsequent systematic mineralogical characterization and metallurgical testwork. Geometallurgy is a technique to document variability within an orebody and quantify and evaluate the impact of many factors including geology and mineralogy on grinding, flotation, leaching and metal recovery processes, while mineralogy is one of the major predictive and trouble-shooting tools for many new mineral projects and operating mines. This paper presents an overview of fundamentals, methodologies and techniques applied in geometallurgy and process mineralogy and highlights the importance of both disciplines in process selection and plant optimization with applicable case studies. INTRODUCTION Precious metals, including gold, silver and platinum group elements (PGE) occur in various geological settings and ore types. The concentrations of these metals in the crust are extremely low and highly variable, resulting in ore variability in many gold, silver and PGE deposits. More importantly, precious metals in an ore may occur in two or three forms (i.e. microscopic, submicroscopic and surface-bound), making ore processing of precious metals extremely challenging. Process selection is most important in any precious metals project and is mainly driven by the grade, reserve and mineralogy of the target elements. Free-milling ores, such as Kupol in Russia, Hemlo in Canada, Grasburg in Indonesia, UG-2 in South Africa, Lac des Iles in Canada, and Noril’sk in Russia, can be processed using flotation or cyanidation with or without gravity. B2Gold Corp, a Canadian gold company, just started a number of new and under construction free-milling gold operations such as Fekola mill in Mali, Mastbati mine in Philippins and Otjikoto mine in Nambia. However, refractory ores (particularly gold ores), such as the Carlin and Goldstrike mines in the USA, Giant in Canada, Pueblo Viejo in Dominican Republic, Porgera and Lihire in PNG, Kittilla in Finland, Fairview in South Africa and Shuiyindong in China, must be processed using pre-oxidation prior to cyanide leaching. In some mildly refractory gold ores, such as Kumtor mine in Kyrgyzstan and KCGM in Australia, ultrafine grinding is required to liberate fine-grained gold particles. For some gold ores containing both free-milling and refractory components (such as Cripple Creek mine in Colorado, USA), two or more recovery processes may be required. The variability of grade, metal deportment, ore hardness and other parameters is one of the risks that encountered in development and operation of many precious metals projects. To minimize and reduce the technical risk caused by ore variability, geometallurgy and process mineralogy have been used by mining companies in the last two decades to measure and quantify the spatial variability of the deposits that are being developed. This paper presents an overview of fundamentals, methodologies and techniques applied in geometallurgy and process mineralogy, it highlights the importance of both disciplines in process selection and plant optimizat"

Jan 1, 2018

By Baidyanath Mandal

Technology in the solid-liquid separation industry has evolved rapidly during the last fifty years and from the beginning, DIEMME Filtration has played a very important role in this evolutionary process by developing innovative solutions, which are used for a diverse range of industrial applications. Since the last decade, we find more and more examples of filter presses employed in the mining & mineral processing field, where high performances in terms of productivity, dewatering capacity and mechanical strength even in extreme working conditions are required. Mainly the requirement of such high quality equipment comes from the Process, however in few cases the reason could be linked with the environment. For stringent process applications like Mineral Concentrates dewatering & leached Slurry Filtration, it requires a high quality & extremely reliable equipment. In these applications, since many years industries are achieving the desired result by using Diemme Filter Presses. Also, recently, due to stringent environment practices are been applied globally, industries needs equipments which could dewater a high amount of residues / tailings with minimal moisture content in the filtered cake. In comparison to all the conventional dewatering equipments, Diemme Filter Presses are most efficient for these kind of product & applications. Diemme Filtration is a highly professional & technological company with several decades of experience in designing equipment for mineral processing. We take up each project as separate & design and manufacture equipment based on individual process or project requirement. This presentation will be focused on the Solid-Liquid separation technologies & equipment Diemme Filtration offers to the mineral processing Industries. It consists of Diemme?s History, Global Network, Technologies & Expertise, R & D Capabilities, Manufacturing Range, Some Applications & results on different mineral processing. Keywords: solid-liquid separation, filtration, dewatering, filter press

Sep 1, 2012

By Z. C. Zhen

Basing on character of fine ores, and employing all the advantage of dissolved-air flotation, the study within the dissertation put forth the methods of superfine metal mineral flotation with dissolved-air flotation equipment, and constructed a full set of laboratory flotation system. Experiments both in water and in slurry were respectively carried out by means of this flotation equipment. Further study was also fulfilled on mechanism of air-dissolved released devices, and the key components of system including ejector, releaser and saturator were designed. Optimizing devices parameters were chosen by taking ideal performance of the devices into consideration, according to orthogonal experiments and tests on bubbles factors, those performance factors were called air release rate, air release efficiency. The results with some minerals are better than JJF flotation machine with 30 litres bulk. The Dissolved-air Flotation(DAF) machine shows great potentiality in treating super-fine metal mineral concentration. The research indicates the Dissolved-air Flotation(DAF) system has superiority over mechanical flotation machine in fine flotation. Air-dissolved released bubbles appear on the surface of hydrophobic minerals in priority, solving collision probability less in the tradition fine mineral separation, such that the metallurgy technology of fine metallic minerals are improved. The exploratory research is a foundation for industrial pilot, commercial test and equipment maturity in the future.

Jan 1, 2014

By Avishan Atrafi

Frothing behavior of surfactants originate from their preferential adsorption at the gas-solution interface. Different surfactants may demonstrate different adsorption behaviors depending on their molecular structure and surface activity. The quantity and rate of adsorption of surfactants at the gas- solution interface in flotation systems will certainly affect kinetics of reaction and fractionation of surfactant between bulk and foam phase and subsequently their frothing characteristics. In this paper, the frothing characteristics of sodium oleate which is the main constituent of fatty acids used in flotation systems is explained. The adsorption behavior of sodium oleate is then compared to a typical non-ionic frother (Methyl Isobutyl Carbinol, MIBC) in terms of different adsorption behavior at the gas-solution interface. Since long chain fatty acids are weak electrolytes, their behavior is a strong function of pH. Also semi soluble salts including apatite contain considerable amounts of ions like calcium in their lattice, so the effect of presence of ions on the frothing behavior of fatty acids requires an investigation. A mass balance on the surfactant transferred to the foam was solved to estimate the bubble surface area flux in foam, which explained how the adsorbed surfactant at gas-solution interface controls the bubble surface area flux at foam. Since sodium oleate adsorption at foam takes place gradually, frother concentration as a function of time was monitored by the total organic carbon measurement (TOC) to compare the surfactant uptake rate at different concentrations, pH and ionic strength. The surfactant concentration adsorbed within foam together with the value of adsorption density from the Gibbs adsorption, leads to the calculation of the surface area flux and prediction of average bubble size in the foam at a specific time frame. This value was compared at different concentrations of sodium oleate. Dynamic surface tension measurements were accompanied to explain the adsorption behavior, though finally equilibrium surface tension turns out to better explain the foamability characteristics. Keywords: flotation collectors, flotation froths, foams, fatty acids, adsorption behavior

Sep 1, 2012

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes are diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favors a different flotation environment. An improvement in the kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferential recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rpm, rotor size/type) at the beginning of the row, where flotation is typically froth phase limited and operational, and set-up parameters have a limited influence on the recovery. ? Higher-powered flotation machines (high rpm, high power rotor size/type) at the end of the row to improve fine particle recovery. ? Lower-powered flotation machines (low rpm, low power rotor size/type) to enhance coarse particle recovery. In evaluating the effect of turbulent kinetic energy on flotation performance, the spatial distribution and its effect on size denominated recovery needs to be evaluated. The mean energy dissipation rate is a measure of the bulk energy input, but CFD-based models offer a more introspective view of flotation sub-processes. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced air and naturally aspirated machines. Keywords: CFD-based model, attachment, detachment, energy dissipation, hybrid energy flotation?, forced air, naturally aspirated

Sep 1, 2012