Search Documents

By Ruddle R. W.

Although copper has been smelted for many years, relatively small attempt has been made in the past to examine the fundamental physical chemistry of the processes involved. Therefore, technological developments apart, slow progress has been made with the development of improved or new principles of smelting. The methods at present in use in the majority of the world’s smelters are essentially those employed at the beginning of the present century; it is significant that many of the textbooks on copper smelting, written some 50 years ago, are still regarded as standard works. The book is divided into seven chapters. In the first the fundamentals of modern smelting processes are briefly outlined for easy understanding of the subsequent sections, while the next two chapters are confined to the more theoretical aspects of the constitution of mattes and slags. Some problems of considerable practical importance are discussed in the remaining four chapters; these are (1) magnetite formation, (2) copper losses during smelting, (3) the recovery of sulphur from the smokes produced during smelting, and (4) the elimination of impurities. A collection of thermodynamic data relevant to copper pyrometallurgy is presented in an appendix, and, for the convenience of readers not well acquainted with thermodynamics, a brief explanation of the thermodynamic terms and methods employed is given in a second appendix

Jan 1, 1953

By A. H. G. Mitchell

Gold-poor and gold-rich porphyry and epithermal gold-silver deposits of Caenozoic and Cretaceous age in the western Pacific and central and eastern Europe are confined to predominantly andesitic continental margins and island arcs. The arc volcanic rocks overlie a complex non-oceanic basement of stacked nappes, the uppermost of which is often ophiolitic. The emplacement of ophiolite triggered a reversal of tectonic polarity, subduction and arc magmatism. Andesitic volcanism and the formation of a strato-volcano were followed by the ascent of magma and porphyry copper mineralisation. Regional propylitic alteration came from convecting, predominantly meteoric fluids. Magmatic degassing caused advanced argillic alteration. This is commonly unmineralised in perched water tables, but may sometimes host high sulphidation gold or enargite gold at deeper levels within the propylitic zone. The onset of extensional stress after the andesitic volcanism allowed meteoric water to circulate to depths of 5 km or more, with consequent cooling of an ascending magma body at depth and the development of low sulphidation epithermal gold mineralisation near and immediately above the sub-volcanic basement surface. All andesitic arcs are mineralised. Regional controls on their ore potential include the level of erosion and geological features in the basement that focus the ascent of fluids. Differences between the mineralisation of the European and the western Pacific arcs may reflect the presence of older, more granitic basements in many of the European arcs.

Jan 12, 1992

By T R. Marrero, J W. Wilson

This paper presents costs for a coal log pipeline that can transport coal over distances from 50 km to 1500 km. The coal log pipeline (CLP) concept is a new technology in w hich coal is compacted into water impermeable circular cylinders that can be suspended in water flowing through an underground pipe. CLP includes processes to prepare the run-of-mine coal for compaction, the injection of coal logs into a pressurised water-lilled pipeline, the conveyance of the coal through a pipe including special pumping stations, and the treatment of the coal logs and water at the pipeline outlet. An 8 inch (203 mm) pipeline can transport more than 2 Ml of coal per year. CLP components have been extensively tested in bench-scale facilities where these tests have included start up/shutdown steady state flow behaviour, end of pipeline treatment of water and coal log handling, water hammer effects, abrasion of logs and pipeline, coal log manufacture, and other engineering operations. Several sites are being considered in the United States (US) for the first commercial demonstration that will probably take place in 1998. The cost calculations are based on realistic values for all the components of a CLP. including a return on investment. For pipelines of different diameter, values for coal transportation are presented in terms of $(USVtonne as a function of distance.

Jan 10, 1996

By A. Paulin, A. W. D. Hills

The work has shown that packed-bed behaviour can be predicted from the results of single-particle experiments, total reaction times being predicted somewhat more accurately than gas and solid temperatures and gas compositions. A small laboratory packed-bed reactor was built and used to study the decomposition of beds of specially prepared CaCO3 spheres, steps being taken to minimise the effects exerted by the walls of the bed on processes occurring within the bed. Gas and solid temperatures and gas compositions were measured at various points in the bed and compared with theoretical predictions based on kinetic data determined in previous single-particle experiments. The measured solid temperatures and total reaction times agreed remarkably well with the values predicted theoretically. Gas and solid temperatures measured after the reaction had finished at any point in the bed did not agree with the theory. This was because solid temperatures in the bed rose very rapidly once the reaction was completed and the walls of the bed could not be heated at a sufficient rate for their temperatures to rise as rapidly; thus some loss of heat from the bed to the walls was inevitable, and this could not be accounted for in the theory. In addition, the theory did not allow for the conduction of heat within the bed, and this resulted in some further slight discrepancy between the measured and predicted values, particularly after the reaction was completed. Gas compositions measured in the bed were rather scattered, but, even so, they agreed moderately well with the predictions of the theory.

Dec 1, 1971

By T. Sharma, T. C. Rao

Laboratory studies have been carried out on acid leaching as a possible route for the extraction of potassium from glauconitic sandstone. Leaching efficiencies with sulphuric, hydrochloric and nitric acids were investigated. The effects on potassium dissolution of temperature, concentration and type of acid, stirring speed and leaching time were also studied. The results show that it is possible to recover 87.5, 93 and 85% potassium with 5 M H2SO4, HCl and HNO3, respectively. During the initial stages of the sulphuric acid leaching process the chemical reaction at the mineral surface is the rate determining step, whereas during the later stages diffusion through the product layer is rate-controlling. Overall, the process follows a mixed-control model that includes both chemical reaction and diffusion. The activation energy for the dissolution of K was found to be in the range 25.79-106 kJ/mol.

Jan 12, 1992

By C. J. Kirkland

25th Julius Wernher memorial lecture given at Tunnelling '91, sixth international tunnelling symposium held in London, 14-18 April 1991. The title gives the lecturer a chance to share some of the lessons he has learnt in a lifetime of tunnelling and particularly in the last six years of his involvement with the Channel Tunnel and the International Tunnelling Association. These included: the difficulties of split contracts but the problems arising with Eurotunnel over the need to create a single owner to whom the banks could lend; the peripatetic nature of tunnellers who built London's underground in the 1960s and returned to build the Channel Tunnel from Egypt, Singapore, Hong Kong and Australia; the increasing requirement for strategic planning resulting in tunnels between European countries and the need for engineers to deal with decision-makers; EU work on harmonising regulations so that there need no longer be, for example, arguments over which regulations should be followed for temporary electrical equipment in the section of the UK tunnel that is technically in France; the huge improvements in safety standards and attitudes; the enormous increase in the scale of undertakings and individual contracts, with an accompanying change in attitudes to logistics; technological advances to cater for the high performance now required of equipment; and the rising importance of environmental issues. The lecturer also briefly touches on the work of the International Tunnelling Association

Jun 13, 1905

By J A. Hacked

This paper explores the potential to exploit controls over the outputs of the primary blasting operation, arising from the performance consistency benefits gained in using modern bulk emulsion explosives technology. The former, allied with the latest powerful blast predictive software and measuring tools, offers the user the opportunity to apply control over both cost and performance, which has not been possible in the past.

Jan 12, 1997

By P. Beauvais

Philip Beauvais, from the Met Office's International Mining and Agriculture Department, explains the need to understand the impact of the weather and climate when developing future mine sites.

Mar 1, 2015

By International geochemical

During the production of the Geochemical Atlas of Finland till samples were collected throughout Finland at a density of one sample per 300 km2. The material studied was the fine fraction of till (less than 0.06 mm). The geochemical mapping has shown that elements that are locally enriched in bedrock in the form of ore mineralisation are also enriched in a wide area of the surrounding till. These anomalous enrichments of ore elements take the form of rectangular or curvilinear zones that are some tens of kilometres wide and hundreds of kilometres long. The mineralised zones host ore deposits of different genetic types and can be termed "ore provinces". They stand out prominently on the geochemical maps and can be divided into sub-units of different chemical composition.

Jan 12, 1992

By D. J. Wall, T. D. Johnson, M. T. Parry, G. R. Heath

In coal-fired power stations coal is ground to a fine powder and then transported pneumatically at 25-30 m/s velocity to remote burners. Wear of the conveying pipework is a well recognised problem and traditional lining materials are Nihard and basalt. In many cases these are being replaced by alumina tiles in order to improve life and reduce the frequency of replacement. A programme of laboratory testing of candidate aluminas with AIO, contents between 85% and 99-5% has been undertaken and the results compared with field experience. This gives confidence in the erosion tests, which were designed to replicate most of the field conditions. However, it has not proved possible to draw correlations between the laboratory erosion rates and any of the materials’ bulk properties. SEM, TEM and microanalysis studies have therefore been made in order to look for microstructural aspects that could be influencing erosion rates and it has been shown that intercrystalline cohesion, the matrix phase and porosity appear to have most influence on wear performance. It is necessary to quantify these microstructural parameters if reliable erosion performance is to be obtained. This paper was read at the Institute of Ceramics Annual Convention at the University of Durham, April 1988.

Jun 12, 1905

By V. Distler, E. F. Stumpfl

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. The massif contains large chromite bodies of "Alpine-type", ophiolitic affinity. Orebodies reach thicknesses of 150 m and sizes of more than 150 000 000 t chromite ore with average grades of 55-60 wt% Cr2O3. Chromites in the Main ore field are low-Al, high-Cr spinels which exhibit some variation in their Mg-Fe distribution. This differs markedly from high-Al spinels in peridotite host rocks and in narrow chromite pods which occur in the western and northern parts of the massif. Chromites carry silicate inclusions, often hydrous silicates such as amphibole. Chromites in massive chromitites contain micron size inclusions of platinum group minerals (PGM). Composite grains containing two PGM and, occasionally, a hydrous silicate are common. Os-Ir alloys rimmed by PGM sulpharsenides occur in narrow serpentine veinlets that cut chromite and are evidence for the reconcentration of PGE concomitant with introduction of As, probably during serpentinisation. Whole-rock PGE contents are highest in massive chromitites of Diamond Pearl mine (totals of 500 ppb). Chondrite-normalised PGE patterns of chromitites show negative slopes which are typical for ophiolitic, podiform chromitites in mantle sequences. The PGE patterns of host rocks are flat and rather depleted compared with those of chondrites and chromitites. Petrological data from unaltered host peridotites suggest a high temperature overprint leading to sub-solidus re-equilibration of olivine and spinel and to the growth of pargasitic and edenitic amphiboles

Jun 16, 1905

By C. C. Harris

The use of Alyavdin's equation Y(x,t) = 1-e(-bt) for describing the effect of grinding time on size distribution is discussed. The equation transforms into linear form by expressing it as log-log reciprocal (1 - Y) versus log t. For plotting, specially divided grids are available; Rosin-Rammler or Weibull charts may be used. The data of Herbst and Fuerstenau are especially useful for illustrating the Alyavdin-Weibull chart in two applications: (1) presenting data (which are relatively unaffected by experimental scatter) and comparing them with theoretical predictions, and (2) as a test for the zero-order kinetics production hypothesis. The chart based on the Alyavdin-Weibull equation is suggested as a useful aid in the analysis of kinetic data (/ versus f), though not as a procedure in its own right. Proposed applications are (1) displaying data with excellent clarity, since it avoids the kind of congestion inherent in some other plotting methods, and (2) as a test for assumed kinetic relationships. Sometimes, equation 1 describes the data quite closely, and in these cases the parameter values appear to be related to certain operating conditions.

Dec 1, 1971

By E. A. Brocchi, P. K. Jena

Complete extraction of copper from Salobo chalcopyrite concentrate can be achieved in less than 10 minutes by chlorination of the dry concentrate with Cl2 at 450 degrees C and in 5 minutes by chlorination of an aqueous slurry containing 5 wt% concentrate at 30 degrees C. In general, slurry chlorination appears to be faster than dry chlorination. The kinetics of dry chlorination of copper sulphide are controlled by an adsorption mechanism with an activation energy of 6.1 kcal/mole. The rate is independent of chlorine partial pressure when pCl2 exceeds 0.4 atm. In slurry chlorination the dissolution of copper sulphide follows a topochemical reaction model and the rate of chlorination decreases with increase in pulp density and also temperature. Dissolved chlorine appears to take part in the reaction in atomic or ionic form.

Jan 4, 1992

By W. J. Whiten, D. W. Grinsberg

Most cluster analysis techniques are not well suited to the analysis of engineering data as they have been designed for more qualitative data that tend to produce compact clusters. A clustering technique is described which develops and uses local cluster shapes to build clusters that are suitable for use in engineering applications. The technique is finding application in the analysis of many types of data, particularly where multiple trends and outlying points occur in multiple dimensions. Applications of particular interest are the calibration of on-stream analytical equipment and the analysis of data on plant performance. In both cases the multidimensional nature of the data renders manual analysis very difficult

Dec 1, 1991

By M. D. Pritzker

Shrinking-core models are used to describe the physico-chemical processes that are associated with many metallurgical gas-solid and liquid-solid reactions. The models can be used to evaluate rate constants and effective diffusion coefficients from experimental data. This work generalises the model for diffusion through a product layer to cases where the transport of more than one species is rate-controlling

Jul 1, 1991

By Winmill T. F.

Paper presented at the at the Institution of Mining Engineers' general meeting held in London on 8th June 1916: In a previous paper it has been shown that the rate of absorption of oxygen by coal is neither directly proportional to the surface area of the coal exposed nor to the percentage of oxygen in the air. Further experiments are now described supporting this conclusion

Dec 1, 1916

By R. Scheepers, J. E. Misiewicz, A. C. Fitzgerald

Discussion by A.C. Fitzgerald of the paper, published in Trans. IMM A, vol.104, 1995, p.B121-B135, is presented together with the authors' response. Fitzgerald points out a number of problems with the idea of mineralising fluids leaving no trace in the large volumes of rock traversed before depositing all minerals of value in a particular horizon or rock type with which the required isobaric or isothermic surface also coincides. He suggested that in the case of the Rooiberg tin deposits, the Lebowa Granites may be batholiths that reached the surface and were capped by sheets of their own volcanics. The authors agree that they had considered a possible syngenetic origin for the stratabound deposits, explain that no conclusive evidence for this could be found, discuss the relative ages of the sediments and volcanics of the Rooiberg Fragment and explain the role of its low-intensity deformation and flat dip in the coincidence of an isobaric-isothermic surface with the lithological stratification

Jun 18, 1905

By M. A. Bussell, G. S. Camm

The study included lode zones at Wheal Pendarves, South Crofty and Rosevale tin mines. Fluid inclusion-containing microfractures are a common feature of the granites and typically show a preferred orientation over quite a large area. The close proximity of a dominant vein or fault controls their density and orientation. They are important pathways for fluids and provide a marker for palaeo-fluid flow. Overprinting provides a reliable representation of the evolution of the hydrothermal fluids in a vein system from early magmatic fluids to late-stage meteoric and basinal brine input. Measurement of microfracture orientation allows estimation of the regional stress regime during a specific hydrothermal event. Since micro- and macro-structures can generally be reliably correlated, these studies assist in modelling the detailed development of complex vein systems. Microfracture density is a good measure of palaeo-permeability, with implications for control of wallrock alteration. The determination of the location and density of microfractures can assist the mine geologist in identifying the location of potentially economic vein structures where macroscopic markers are absent

Aug 1, 1996

By A. G. Royle

Sampling formulae for in-situ material, hard rock sampling and alluvial sampling are briefly discussed

May 1, 1991

By R. R. Tatiya

The following procedure was used to determine cut-off grades: define the orebody profile; plan the stope layout and quantify the work involved; formulate equipment-performance norms; calculate unit costs; input process recoveries and metal prices; and calculate the cut-off grade. Use of the method is illustrated using data from a copper mining complex in India. Results from the study led to the following conclusions for underground mines in general. Cut-off dependent costs vary significantly with the stoping method employed, orebody thickness, the degree of mechanisation and the working efficiencies of the workforce and equipment. This applies even within the same deposit. Sub-level stoping and its variants can be operated at a lower cut-off grade than cut-and-fill and its variants. Thinner orebodies affect cut-off grades adversely, but with thinner orebodies very little further reduction in cut-off grade can be achieved once a certain minimum width has been exceeded. For the same stoping method and in the same mine the cut-off grade varies with the degree of mechanisation. Labour-intensive methods require higher cut-off grades. An allowance for working efficiency should be made when calculating cut-off grades. Higher process recoveries allow a significant lowering of cut-off grades

Jul 1, 1996