Search Documents

By Donald Jonson

The Arlanda Link project is for the time being the most interesting project in Sweden, concerning rock and blasting technology. The total amount of rock excavated beneath Arlanda airport comprises 800 000 m³ divided in four parallel tunnels measuring a total length of 8,5 km, with a rock covering of only 5-15 m between the tunnel roof and existing terminal buildings.

Jan 1, 1997

Existing geological structures such as faults or shear zones can greatly influence the interpretations of amplitude or energy attenuations of measured blasting vibrations along both affected and unaffected orientations. Mineralisation in conjunction with large faults or shears is commonplace in the geology of steeply dipping metalliferous deposits, such as those found in the goldfields of Western Australia. Better understanding of the influence of faults or shear zones on blast-induced seismic waves can lead to more effective blast vibration monitoring programs and interpretation of the results measured along affected orientations.

Jan 1, 2011

By J. Sigler

A series of small scale tests have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite were tested. The charge configurations included detonating cord placed in five holes with water as a coupling medium or concentrated charges of equal mass, placed in the same number of holes, fully stemmed or air decked. The powder factor was varied from 0.4 to 1.2 kg/m3. Typically all charges were detonated simultaneously; however, in some experiments, detonation waves collided in the middle of each borehole and in others a small delay was used between charges. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using a standard Bond mill arrangement. The experiments generally showed increased softening of the rock with powder factor, which appeared to be the dominant factor. Charge configuration as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2008

By J. Rafael Otaíza, Francisco Mardones

This work has addressed the problem of creating a predictive model of the maximum particle velocities in the rock mass (PPV). The model designed specifically can model the subsequent vibrations of blasting based on geometric parameters, explosive loading, and the blasting process itself. Models based on artificial intelligence (AI) algorithms can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. These models have been successfully used in similar contexts (Prashanth, (2018)) and have achieved state-of-the-art results in the field (Lawal, (2021)). The main challenge is to adapt them to the context of Chilean mines, in addition to including the geometric information of the blasting and the heuristic to obtain the set of optimal parameters, it is proposed to follow the work of (Simonyan, (2013)) and obtain "saliency maps" adapting it to tabular variables. We implemented an Artificial Neural Network (ANN) with a large number of neurons in the hidden layers. Models based on neural networks can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. The literature shows that, for the problem of rock type identification, basic neural networks perform well (Simonyan, (2013)), but lack uncertainty estimates. This is a data-driven model, and in this sense, the model training was carried out using data from multiple operations in the large copper mining industry in Chile. In these databases, data consistency and the balance of the various independent variables that have the greatest impact on the model were ensured. With the above, the optimal hyperparameters of the model were determined, obtaining a predictive R-squared of 0.94.

Jan 21, 2025

By L. Muñoz, L. Steffen, W. Vilas

The emission of particulate material is one of the several parameters related to environmental control in mining operations near communities. Blasting is an event that generates and leaves a large amount of dust in suspension, which can cause discomfort to communities, generating complaints that can compromise the operational continuity of the mine. The proper management of these environmental impacts is a key factor to ensure a good relationship with the neighborhoods, making a responsible mining in harmony with the environment, giving sustainability to the mining business in the medium and long term. The main goal of this work is to present different techniques and technologies applied in a large-scale open pit mine in Brazil, with operations close to a community, to minimize the emissions of particulate material into the atmosphere. For this, different technical solutions were implemented. First, a non-conventional blasting technique was introduced that incorporates special charging and timing configurations, generating a first upper layer that serves as a blanket to contain a second, higher-energy lower layer. An optimal stemming was also defined in order to minimize ejections and maximize cratering, using the scaled depth of burial theory as well as video and fragmentation analysis. In addition, changes were made in the timing between decks (to guarantee a minimum time between layers) and between holes (changing the initiation point opposite to the free face). Finally, additional measures such as humidification of the bench, use of a wind vane to identify wind direction and the construction of a physical barrier between the mine and the community were implemented as additional mitigation measures. By applying the above techniques together, in some specific zones of the mine, it was possible to considerably reduce the ejections generated by blasting versus conventional blasting without the above measures, which was demonstrated in the field with dual blasts trials. Additionally, it was possible to achieve a vibration reduction in the community of ~30%. This work demonstrates how, by applying these technical solutions, it was possible to minimize the dust and vibrations generated by blasting allowing this operation to do sustainable mining

Jan 1, 2024

By William H. Snyer, Hank Cox

A high explosive device using Linear Shaped Charge (LSC) (to rapidly cut vent and drain openings in a rail tank car) is described. In the event of damage to a tank car loaded with a pressurized flammable fluid, it may sometimes be necessary to perform controlled on-site vent, drain and burn operations. Existing techniques required refinement to achieve the desired safety and procedural reliability for use in emergency situations.

Jan 1, 1994

By Joseph A. Meyers

Explosives techniques and technology are constantly evolving and improving, yet basic communication and business skills are not being used regularly. Many potential blasting projects never occur due to simplistic, basic factors, such as a lack of communication. Articulate communication is the key component in the blast approval process, which has changed remarkably from how business was conducted fifty years ago. Imperative to the approval process is communication outlining the safety and benefits of the blasting project.

Feb 1, 2020

By Z X. Zhang

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By R. Ticona, J. Alarcon

In the continuous search to provide comprehensive solutions and identify opportunities to improve ore traceability, from the blastholes to mill feed, different ore traceability systems have been developed, which allow tracking the ore and associating its geometallurgical characterization of different sectors of interest from blasting to the processing plant, facilitating decision making and operational actions when detected during each stage of the plant. With the objective of improving the ore tracking from the mine to the processing plant in a Peruvian copper mine operation, the impact on the processing plant was evaluated in relation to blasting optimizations through a tracker system, relating the processes performance of the whole production chain with the geotechnical and geometallurgical properties ores in real time in the process plant: detecting when it was feed waste, high grade ore, low grade ore and ore with arsenic, among others. Unit and integral tests were carried out over a period of three months, with an implementation of tracker detection portals in the processing plant, which allowed to verify the proper communication of data and the web platform. The tests were focused on several blasts where the ore was in contact with waste and it were directly sent to the plant, with a classification by type of grade (high, medium, and low grade), type of material (ore-waste contour), this stage allowed to make operational adjustments in the field and in the mining operation. Finally, in the economic results, the special tests had 1000 trackers, obtaining for this project a sensitization of a cost benefit for the test stage, for the reduction of 50% of the waste material feed has crushed, with an estimated benefit of 1,987,646 USD.

Jan 1, 2024

By Steven Putt

The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

Feb 1, 2020

By P A. Lang

Canada is constructing an Underground Research Laboratory as part of a comprehensive program to evaluate the concept of nuclear fuel waste disposal deep in stable rock formations. Careful blasting methods have been designed and quality control procedures have been used for the excavation of the access headings in the underground facilities. This paper describes the work done between 1984 December and 1986 December at the second level, 240 metres below surface.

Jan 1, 1987

By Cary Moffat, John Kita, Rick Walker

The Lac des Iles Mine, in an isolated area of NorthwesternOntario is a relatively new open pit platinum and palladium mine. They were encountering problems with the equipment and production scheduling when ramping down to begin production on the subsequent benches. A co-operative effort between Lac des Iles Mine operation people, ICI Explosives, and the mines drilling and blasting contractor - Consbec Inc., resulted in a decision being made to use full depth sinking cuts to provide access to the next bench.

Jan 1, 1996

By Stuart Brashear, Steven Bell, Donald Smith

This Limestone site required the removal of a bench containing high quality rock located in close proximity to sump and pit pump. The sump and associated electrical box were below the bench that needed to be blasted and located only 70 feet (21.33 meters) away. It was proposed to blast material needed without moving or disturbing the pump or electrical junction box. The area to be blasted was flown with a drone and stitched into a 3D orthographic model. Proprietary blast design software was used to create a blast design solution that would allow for a series of blasts that would provide required fragmentation and muckpile development and not disturb the sump or electrical box. A drill patten was created for each blast using the burden heat map and 3D face profiles created from the 3D orthographic model. Timing contour lines and muckpile displacement predictions were used to create timing sequences for proper face movement away from the sump and electrical box. The shot designs were laid out with a GPS system to insure hole location accuracy. All holes were remeasured for proper face burdens using the 3D model and Boretrak®® data collected after drilling operations were completed to insure hole locations were within face burden tolerances as derived by the burden heat map. After each drill log was reviewed, a charge loading scenario was created for each hole. The timing design created, for each shot and was reviewed and adjusted as needed with regard to desired muckpile displacement away from the sump and electrical box. Blasting results were satisfactory, with fragmentation and muckpile development consistent with the calculated throw from the blast model, with no rock hitting the pump or box and no rocks striking the sump water and disturbing the pump motor.

Jan 21, 2025

By David Porter, Nathan Rouse

The implementation of presplit blasting has been widely utilized in open pit and underground tunneling. This case study works through the iterative process of developing a heading drill and blast design to control overbreak and limit backbreak in cut and fill headings. The initial design was based on rule of thumb parameters, and the design was then modified for the field conditions based on results. Throughout the design process the drill profile, explosive charge, and timing were modified to yield the best profile compared to design. Data collection during the design process was extensive to best understand the effect of modifying parameters, and gauge performance of design changes. Input from the miners as well as engineers was considered to allow for the best possible adaptation of the design change from existing practices. During the process resistance to change was realized and accounted for to understand the issues that the miners were facing and how to best address them while ensuring high quality blasting. Workforce buy- in was addressed by illustrating the long term benefits of higher quality blasting and the tradeoff of with a slightly more in depth drill and loading cycle.

Feb 6, 2023

By Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Mehmet Aksoy, Deniz Adiguzel

The environmental problems arising from ground vibration has been faced and discussed frequently in various industries such as quarry, mining, civil works, shaft, tunneling, pipe line and dam construction etc. where the blasting operations are unavoidable. In bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. The prediction of ground vibration components plays an important role in the minimization of the environmental complaints. This paper presents the results of ground vibration measurements carried out in the quarries located on the different sides of Çatalca district in Turkey. In order to predict peak particle velocity level for this district, ground vibration components were measured for shots during bench blasting at these quarries. In blasting operations; ANFO is commonly used as blasting agent at the quarries. The type of priming and firing differed from quarry to quarry. The parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events by using different type vibration monitors. The absolute distances between shot points and monitor stations were determined by using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. In order to predict, and compare the influence grades to the neighboring buildings, and structures at the Çatalca district, the particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms due to the lack of a national standard in Turkey. Then, the data pairs belonging to these quarries were gathered together to represent the district and were analyzed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance

Jan 1, 2007

By G. Walsh, M. T. Wild

In this paper the performance effects of linear shaped charges will be discussed. Different sized charges were tested and reviewed based on their performance used with a typical detonation method vs. detonation with a line wave generator. The goal of the project was to determine if the linear shaped charge had better performance with an ideally linear wave moving through it, verses a swept wave that is currently used. A line wave generator is a flexible sheet explosive formed into a triangular shape with holes placed in strategic places to cause a detonation wave to become linear across the width of the triangle. A standard linear shape charge with a detonator in the side of the charge was be detonated against a witness plate to get a standard depth of penetration. A second standard linear shape charge with a detonator connected to the top of a line wave generator, the line wave generator placed on top of the linear shape charge, was be detonated against a witness plate to get a comparison depth of penetration. All charges had a standoff 1.5 times the width of the cavity, allowing the data to be compared to the control charge. Computer modeling was intended to be used to predict the results from testing these designs in the field. The actual results were compared among themselves.

Jan 1, 2011

By Travis A. Davidsavor, Charles Dowding, David A. Provost, Yonggang Gou

This paper compares measured blast induced strains on operating, full scale, buried pipelines with three similar past studies. The recently performed study represents realistic and modern pipeline blasting techniques combined with modern data acquisition. The evaluation compares measured PPV and strain, as well as calculated stress, at equivalent scaled distances.

Feb 1, 2020

By Jacqueline Berendzen

Summer internships are a great way for students to explore different career paths in the industry and get first hand experiences with potential employers. As a junior in mining and explosive engineering, my 2009 summer internship gave me a behind the scenes view of the actual workings of an explosive company and the role they play in the mining industry.

Jan 1, 2010

By S. S. Bud Jenkins

I went to an underground limestone mine recently to demonstrate the use of borehole liners. The liners were for horizontal holes in a normal “V” cut tunnel round. I hadn’t been in this mine for about 40 years. What a change. Way back they used cap and fuse and lit each fuse individually with a blowtorch. The face was about 40 feet wide and 14 to 16 feet high. They used ladders to get to the upper holes. The rounds were mostly slab rounds. I never saw this happen but had heard several times that the first holes were going off before the last holes were lit. I guess if this was true the use of slab rounds was a plus for safety. As far as I know they never had an accident but it was a scary procedure. There were a lot of scary procedures in the past and thankfully things have changed.

Jan 1, 2010

By Eric C. Gerst

"In this current era of soft commodity and coal prices the mining industry is turning towards optimizingall levels of production to reduce operating costs. Part of this trend includes the automation of miningmachines. As the first tier of the mining process blast hole drill automation offers benefits through the entire value stream from drill bench to material processing."

Jan 1, 2017