Search Documents

By T. H. Dubaniewicz

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 2010

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963

By R. K. Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed which allow the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

By D. Bienstock

As part of the development of the hot-carbonate scrubbing process by the Bureau of Mines, the corrosion rates of steel in boiling solutions of potassium carbonate saturated with carbon dioxide and hydrogen sulfide were determined, and the effectiveness of various inhibitors was evaluated by Bureau researchers. The highly corrosive solution of carbonate saturated with carbon dioxide can be inhibited with a 0.2-percent concentration of either potassium chromate or sodium metavanadate. Solutions of carbonate saturated with carbon dioxide and hydrogen sulfide are mildly corrosive, 0.01 inch per year. Complete absence of corrosion is obtained with 0.2 percent sodium metavanadate or 0.15 percent vanadium pentoxide. Oxidizing inhibitors such as potassium chromate are destroyed in the alkaline sulfide mixture, N-alkyl trimethylene diamines, at a concentration of 0.1 percent, lower the corrosion rate to about 0.005. Sodium metasilicate, at a concentration of 0.6 percent, completely inhibits the corrosion but may deposit free silica in the system. Commercial cladding materials such as the epoxy coatings also prevent corrosion.

Jan 1, 1962

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau's long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth's crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962

By E. L. McHugh, J. M. Girard

This paper discusses the results of two recent case studies in which high-tech prototype instruments were used. The first case study describes the results of a ground-based hyperspectral imaging tool used to map the geology of an open-pit mine highwall. The second case study outlines the use of interferometric synthetic aperture radar and how this type of radar can be used in a variety of geotechnical situations. These case studies are part of an on-going research project at the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory. The project objective is to implement engineering controls and design methods in order to reduce the number of injuries and fatalities associated with slope failures at mining operations. Project personnel are hopeful that these new developments in technology will lead to better geotechnical monitoring and design in slope stability and other important areas of rock mechanics.

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

By W. H. Tavenner

The Bureau of Mines gathered test data on the use of a continuous borer in mining an anthracite bed, which was 30 feet thick on a pitch of 15° to 45°. Gangways were driven with the continuous borer, ventilation openings between gangways were driven with a large-diameter auger, and the blocks of coal between completed gangways were mined by the long-hole method, Conveyors were used to transport the mined coal. The continuous borer operated on a coal floor that was frequently soft because of heaving. The continuous borer could not bore openings on a grade exceeding 27 percent (15° pitch). Because 150 was also the lower limit of the pitch, of the bed, the continuous borer was used only to drive gangways. The continuous borer virtually filled the workplace, leaving insufficient space to place heavy-duty timber and cushioning material between the timber and coal back to allow for normal expansion of the uncut coal. The light? weight yieldable steel arch against the coal back gave inadequate support to control convergence, which in a disturbed area sometimes occurred with explosive violence. This exposed the machine operator to a hazardous condition, since a satisfactory solution could not be found, the company discontinued the use of the continuous borer.

Jan 1, 1966

By O. C. Blade

"An important function of the Bureau of Mines is promoting the conservation and more efficient utilization of a natural resource. Petroleum is such a resource, and its utilization depends to a considerable degree upon its characteristics. For this reason the Bureau of Mines, over a period of years, has analyzed many samples of crude petroleum by the Bureau of Mines Hempel method 3/ and published complications of crude-oil analyses. Among such publi¬cations are several reports presenting analyses of crude oils from fields in Oklahoma. The most recent of these relates to samples from southern Oklahoma. 4/ The present paper provides additional analyses of Oklahoma crude oils, largely from areas and formations not heretofore represented in published reports. The analyses of 248 samples from 153 fields are presented individually and collectively in the tables of this report.Crude oil has been produced in Oklahoma in commercial quantities since 1891, and peak production was reached in 1947. The State's cumulative production to January 1, 1944, is, according to the American institute of Mining and Metallurgical Engineers, 5,186,466,000 barrels. 5/ The annual production of crude petroleum in Oklahoma for each year from 1891 to 1943, inclusive, is given in table 1."

May 1, 1945

By L. Stein

A simplified radiochemical method has been developed for quantitatively analyzing; radon gas in underground uranium mines. In this method, a measured volume of air is drawn by a pump through a drying tube and a cartridge containing dioxygenyl hexafluoroantimonate reagent. Radon is captured as n nonvolatile product. After radioactive equilibrium has been established between radon and its short-lived daughters (approximately 4 hours), the gamma-emission of the cartridge is measured with a scintillation counter. The amount of radon is then calculated from the gamma-emission rate. The effect of cartridge geometry, reagent load, and air flow rate upon collection efficiency and counting efficiency is reported.

Jan 1, 1977

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of nee' water and reused 3.8 billion gallons for a total usage of 12.4 billion gal¬lons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain this high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ore near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand for new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements ill the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By John C. Machisak

DATA ON INJURY experience at quarries and related plants of the United States are presented in this publication under the following general sections: A) General injury experience: Tables 1-4: Contain current data on number of injuries, injury-frequency rates, work location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 5-6: Current data on number of injuries, injury-frequency rates, work location, accident agency, degree of injury, and related employment data. (C) Injury experience by States: Tables 7-19: Current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data. (D) Selected injury data: Tables 20-30: Current data on various selected factors of operating conditions at different kinds of quarries, including employment size-groups, length of shifts, comparative severity of injuries, and injury data and related employment experience at dimension-stone and crushed and broken stone quarries, and underground quarries. (E) Mining methods and historical injury experience: Tables 31-32; Employment data and injury experience in the quarrying industries of the United States, by mining method and work location, 1953-58; and historical injury experience and employment data in the quarrying industry, 1911-58.

Jan 1, 1962

By James J. Dowd

During and immediately following World War II, the heavy demands for steel required the mining of unusually large quantities of coal for the manufacture of metallurgical coke. The largest demand for metallurgical coke is in the Appalachian region, which comprises central and western Pennsylvania, Maryland, West Virginia, Virginia, eastern Kentucky, Tennessee, and Alabama. This demand is satisfied by coke made from coals within the region; consequently, the reserves of coking coal in this region are being depleted more rapidly than reserves in other coal-producing regions. The supply A' high-quality coking coal during the war was inadequate, and some coke were forced to use inferior coals. The coke produced from these inferior coals adversely affected the rate of production. Another national emergency probably would produce a similar condition, and in the interest of -national security, the Munitions Board of the National Military Establishment requested the Bureau of Mines to evaluate the reserves of coals suitable for the manufacture of metallurgical coke. All bituminous coals in the Appalachian region are coking, and as the coal that produces the better metallurgical coke become depleted, other coal previously considered inferior will be used. The general trend is toward the use of lower-quality coals for metallurgical purposes.

Jan 1, 1950

By Richard A. Watson

A frequency-shift keying (FSK) modulator-demodulator (modem) network has been devised for the Bureau of Mines mine-monitoring systems. This network permits an unlimited number of remote stations to communicate with one central station over the same pair of wires. The network operates at a speed of 4,800 Bd at distances up to 5 miles. This report describes the development and operation of the modems. The theory of operation, schematic diagrams, and printed circuit board layouts are provided. Although the modems were built for a specific application, a more general use is discussed whereby the network would operate with a typical serial channel format.

Jan 1, 1985

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By S. Harteis, D. Dolinar

Many mining operations rely on bulkheads to provide a barrier between impounded water or slurry and active mine workings. However, bulkhead failures could cause and have caused catastrophic flooding that puts the underground workforce at risk. The National Institute for Occupational Safety and Health1 (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) is conducting research to evaluate the adequacy of existing design practices for water and slurry bulkheads. A key component of this research effort is documentation of the performance history and design parameters for bulkheads installed in underground coal mines during the last 20+ years. This research is part of a larger effort to develop general design guidelines and procedures for constructing and maintaining bulkheads that will help to ensure their long-term structural integrity, while significantly reducing the inundation risk for miners. This paper presents the results of NIOSH’s research to identify state-of-the-art bulkhead designs, including design criteria, leakage monitoring systems, and emergency warning systems. Underground observations and evaluations of existing bulkheads suggest that the most important design factors influencing their performance are the interface of the bulkhead with the surrounding strata and the potential magnitude of the hydraulic pressure to which they may be subjected. When a bulkhead has failed, leakage has generally been through the surrounding strata or along the bulkhead/strata interface, with the failure potential along the interface increasing with hydraulic head. It was also determined that development of a monitoring program to ensure the long term structural integrity of bulkheads is an important safety consideration. Current monitoring procedures range from weekly visual inspections to constant monitoring via pressure transducers and fluid level indicators. Where possible, these devices are used in conjunction with a computer based mine monitoring system to alert mine personnel when an emergency condition exists at the bulkhead installation.

Longwall minim; is a highly mechanized, high productivity mining method that is finding increasing applications in coal. Although the method would be highly advantageous in certain hard rock mining applications it cannot be applied in hard rock because no suitable cutterhead exists for such materials. The wedge longwall cutterhead is a, roller cutter device that is wedge-shaped, with cutters arranged to eliminate the very large normal force ordinarily required to cause such cutters to penetrate hard rock. However, the wedge geometry cannot be extended to a point: special nose cutters are needed to open a narrow slot for the wedge. This report describes the design, fabrication, and successful field testing of these critical nose cutters.

Jan 1, 1974

The NIOSH suite of coal mine ground control software addresses nearly every aspect of coal mine ground control planning, including geologic characterization, mine layout, pillar design, and support selection. Mine planners who use the soft-ware have access to the knowledge gained during years of NIOSH research—packaged in a simple, easy-to-use format. Several of these software packages have recently been updated and improved. Analysis of Roof Bolt Systems (ARBS) (Figure 1) helps select the proper roof bolt system design from the immense variety of available bolt types and patterns. It was developed from statistical analysis of extensive bolt performance and roof fall data. New features in Version 2 include— • The capability to analyze roof bolt systems that use two types of bolts; and • A roof support cost module that estimates the total in-stalled cost of different patterns, considering the costs of consumables, labor, maintenance, and other factors. The Support Technology Optimization Program (STOP) (Figure 2) can be used to make judgments regarding which secondary support system will be the most effective in a particular mine condition and to evaluate the advantages or dis-advantages of alternative support systems. Version 3.0 includes additional improvements: • Supports with large load-shedding following yielding can be designed based on the peak loading capability as well as the residual loading capability; • Seven new support systems have been added to the program; and • Easier access to photo gallery has been provided. The Coal Mine Roof Rating (CMRR) replaces com-plicated geologic information with a simple numerical rating that mine planners can use in many ground control applications. The CMRR can be readily integrated into a geologic exploration program, and the software package is capable of generating an AutoCAD CMRR "layer." Version 1.2 contains— • The complete CMRR database with more than 250 ratings obtained from 70 different U.S. coal seams; and • An all-new "Help" file that clearly explains all aspects of the program. Analysis of Horizontal Stress in Mining (AHSM) can help find the optimum mine layouts for control of horizontal stress. It can be used to analyze both development and longwall retreat designs, and it shows how the stress condition varies as the entry, crosscut, and panel orientations are changed. Version 2 features— • Improved graphics that enable the user to observe the effect of design changes without adjusting the display on the computer screen; and • Resource files containing information on stress map-ping, advance-and-relieve mining, stress measurements in U.S. coal mines, and other topics. [ ]

Jan 4, 2006

By Paul J. Guay

This report presents the results of evaluating a longwall mining system specifically designed to extract a very deep web (60 inches or deeper) from a longwall panel. The report includes a productivity and cost analysis comparing the new mining sys-tem with a high capacity conventional longwall operation taking a 30-inch wide web. The analysis shows the new system will increase annual production 44 percent and decrease cost per ton off the face 21 percent. The report also includes conceptual drawings and specifications for a high capacity four-drum shearer and a unique shield type of roof support specifically designed for very wide web operation. The advantages and problems associated with wide web mining are discussed in general and as they relate specifically to the equipment selected for the new mining system. The study concludes by recommending that surface coal loading tests be conducted as the follow-on work.

Jan 1, 1978