Search Documents

By R. D. Leitch

"INTRODUCTION The character of mine drainage from areas of low pyritic coal3 and from average pyritic coal4 has been investigated, and to complete the study it seemed desirable to select a number of mines situated in high pyritic are as to determine whether or not this variation determines the relative acidity of drainage from mines operating in these characteristic coal fields. Advantage has been taken of some worked on in 1918 by Henry Leighton 5, then Professor of Economic Geology, University of Pittsburgh. He visited and has reported certain areas of high pyritic coal which we also visited during this study. Many of the mines were found to be idle in 1930 and a few were caved shut, apparently for several years. However, samples of the outflow from all mines visited were collected if possible and analyzed, and some general information was gathered for each mine. The map (fig. 1) shows the location of these areas as given by Leighton.ACKNOWLEDGMENTSThe information and assistance obtained from officials and others at the mines visited during this study are gratefully acknowledged, as well as the original suggestion from Dr. Glenn V. Brown of the State Sanitary Water Board who called attention to the desirability of such a study.Thanks are also especially due the coal laboratory of the United States Bureau of Mines, under the direction of H. M. Cooper, for the analyses and determination of sulphur forms in the large number of solid samples necessary to the work reported,This study has been carried on under the direction of R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station, of the U. S. Bureau of Mines."

Jan 1, 1932

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.

By J. Bennetts

As part of its mission to develop technology that will help increase the supply of critical and strategic minerals from domestic resources, the Bureau of Mines has investigated methods for beneficiating platinum-group metal ores from the Stillwater complex, Montana. This report presents the result of a bench-scale study employing froth flotation to recover a sulfide concentrate containing platinum-palladium values from a mineralized gabbro. Best results were obtained with a flotation scheme utilizing a mercaptobenzothiazone collector and sulfuric acid. Rougher concentrates containing approximately 11 oz Pt-Pd/ton and 90 pct of the metal values in the ore were obtained. Subsequently, cleaner concentrates containing approximately 26 oz Pt-Pd/ton and between 80 to 85 pct of the Pt-Pd values in the ore were prepared.

Jan 1, 1980

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By Heithecker R. E.

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce,, published a report of the gas reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, may be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By R. E. Heithecker

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce, published a report of the gas at reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, nay be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By C. Fang, D. B. Kittleson, K. L. Rubow

"Under contract to the U.S. Bureau of Mines, a study was conducted to investigate the feasibility of using the microorifice. uniform deposit impactor (MOUOI) to measure the size distribution of aerosols containing various mixtures of coal dust and diesel exhaust particles. The project objective was to determine if the mass concentration of diesel exhaust particles, in an airborne mixture of coal dust and diesel exhaust particles, could be determined on the basis of the size distribution of the two aerosols. In general, the mass of diesel exhaust particles is in the submicrometer size range while that of the coal particles lie in the larger size ranges.The MOUDI is a cascade impactor with small diameter nozzles to obtain small cut sizes and rotating impaction plates to avoid particle overloading of the deposit. For this study, a 7 stage version was used. At the sample flow rate of 30 L/min, the cut sizes were 0.10, 0.23, 0.70, 1.0, 2.6, 4.9 and 10 pm.Size distributions of aerosols generated in the laboratory and in several underground coal mines were measured. The primary emphasize of the laboratory tests was to ascertain if the diesel exhaust particles could be separated from the coal dust, regardless of mass fraction of the diesel exhaust particles in the total aerosol mixture. Diesel exhaust, from a Caterpillar Type 3304 NA diesel engine, was mixed with coal dust generated with a· TSI Model 3400 fluidized bed dust generator. Experiments showed the size distributions of the mixed aerosols exhibited two definite modes with the minimum between the two modes in the 0.7 to 1.0 um size range. Distinct modal separation was obtained as the mixture fraction of the diesel exhaust aerosols was varied from 3% to 98%.The field study was conducted in three underground coal mines, two utilizing diesel-powered equipment and the third exclusively using electric equipment. Sampling sites were selected to obtain a wide variety in the diesel exhaust and dust aerosol concentrations. Size distribution data showed these aerosols are bimodal. The mass median aerodynamic diameters of the diesel particulate mode and the coal dust mode were approximately 0.15 µm and 3 to 10 un, respectively. The results, in all cases, clearly show a separation between the two modes in the 0.7 to 1.0 µm size range with the minimum in the vicinity of 0.8 pm. The separation was found to be independent of mass fraction of the diesel exhaust particles, total particle concentration and sampling site."

Jan 1, 1989

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

By Edward Kline

A review and synthesis of literature pertaining to biological consequences of submarine mine-tailings disposal (STD) was conducted. STD can result in massive sea floor sediment deposition. STD may also increase suspended sediment, trace metals, and residual milling reagents in receiving waters. These perturbations, which are highly site dependent, invariably smother benthic organisms, and could potentially affect or alter fish, plankton, and benthos through acute and chronic toxicity, bioaccumulation, behavioral changes, smothering, derived secondary effects, and habitat alteration. Much of the available information concerning STD is unpublished and limited to a restricted number of sites. From this information and related research, it appears that benthic smothering is the only major consequence of a properly designed STD system. There have been cases of metal bioaccumulation due to inadequate preliminary evaluation, Also, shallow water habitat alteration has resulted from STD. Reductions in biological production are likely due to benthic smothering. The rate of ecological recovery after termination of an STD operation varies and is difficult to assess, The consequences of STD are site specific. Additional research is needed concerning possible consequences of milling reagents and the broad implications of benthic smothering. Also, methodologies are needed to allow better prediction of benthic recolonization and ecological implications of metal bioaccumulation.

Jan 1, 1994

By M. H. Salsbury

This report describes the tunneling at the Leadville drainage tunnel, which was resumed in September 1950 with funds made available in the 1950 appropriation of the Department of the Interior. It brings up to date the account of the first project, carried on from December 1943 to August 1945, published by the Bureau of Mines which supervised both the first and second projects. In this report Leadville mining history, particularly related to drainage efforts, and the possibilities for future mine drainage are discussed briefly. An account of the second project, including a description of the operating cycle, exploratory drilling done as a safety measure, surveying procedures, geology, cost data, and other pertinent information, completes the report.

Jan 1, 1956

By R. G. Knickerbocker, T. E. Evans, J. L. Morning, D. R. Torgeson, F. W. Wessel

"INTRODUCTION Pilot-plant studies on processes for converting low-grade domestic manganese ore to high-grade oxide or sulfide products by pyrometailurgical process was initiated at the Boulder City, Nev., Experiment Station in 1942. These investigations were given impetus by the possibility of a national shortage of ferro-grade manganese oxide for war needs.The manganese ore employed-in most of the pilot-plant smelting tests was from the manganosiderite-nodule deposits at Chamberlain, S. Dak. This deposit although low-grade, is extensive and represents, the largest reserve of manganese in continental United States. 6/ The Bureau of Mines has recently developed a Carryall mining-conical rolls treatment method that shows promise of making possible economic removal and subsequent beneficiation of the nodule-bearing shales. 7/ Smelting tests were made also on Artillery Peak, Ariz., mill concentrates in the productions of unrefined manganese matte for the steel The pilot-plant smelting program was based upon the fundamental fact that manganese, like copper, will sulfidize and become miscible with FeS. The matte this formed represents the initial smelting step in the pyrometallurgical treatment of the beneficiated ore. The concentrated nodules containing about. 18 percent manganese were smelted with varying amounts of pyrites and appropriate fluxes to produce Mns-FeS mattes containing 16 to 50 percent manganese. When the manganese and iron was completely sulfidized, the mattes contained 16 to 23 percent manganese. Reducing the pyrite resulted, of course, in the selective sulfidization of manganese and the production of a matte containing a correspondingly higher ratio of MnS to FeS. Complete sulfidization smelting produced slags of lower manganese content and hence resulted in higher manganese recoveries in the matte."

Sep 1, 1946

By Avis W. Effinger

In conjunction with pilot steamflood tests in the Venango sands of Warren and Venango Counties, Pa., the Marx and Langenheim (4)3 calculations were adapted and programed for digital computer solution to predict test performance. The Monte Carlo technique was incorporated in the calculations to provide values of several variables which could not be adequately defined from available information. The computation methods are explained and the FORTRAN IV program listing is presented. Data and results of the prediction calculations for Venango oil sands are also shown.

Jan 1, 1969

By D. K. Deardorff

The purpose of this work was to investigate the hafnium-carbon phase diagram. Alloys used to study this system were prepared from high-purity components by both consumable-and nonconsumable-electrode arc melting. Data for the diagram were obtained on the alloys by metallography, optical pyrometry, thermal analysis, heat treatment, and X-ray diffraction. The data indicate that a carbide compound occurs over considerable range of composition, and that one of each of the following types of reactions occurs in the hafnium-carbon system: Peritectoid, peritectic, and eutectic. The maximum melting temperature of hafnium carbide is 3,840° C at 49 to 50 atomic percent carbon, and the composition range of hafnium carbide at temperatures of 2,150° to 2,380° C is from 37.0 to 48.5 atomic percent carbon. The hafnium a-S transformation temperature is raised on alloying with carbon from 1,750° to 1,890° C, where a peritectoid reaction isotherm occurs. Alloying hafnium with carbon increases the hafnium melting temperature from 2,190° to 2,250° C, at which temperature a peritectic reaction occurs. Hafnium carbide and carbon react at 3,055° C to form a eutectic of 68.3 atomic percent carbon.

Jan 1, 1967

By Ronald P. Hollenbeck

Shales in the Appalachian Region of Kentucky and Tennessee were sampled and tested to determine their use as raw materials for the manufacture of lightweight aggregate by the rotary-kiln method. Nine samples were obtained from eastern Kentucky and 143 samples were obtained from eastern Tennessee. As a result of preliminary testing of these samples, two sources in eastern Kentucky and 11 sources in eastern Tennessee were resampled for rotary-kiln tests. The rotary-kiln tests showed the two sources in Kentucky and seven sources in Tennessee contained shale that would produce satisfactory aggregate. Lightweight aggregate processed from these nine sources was tested in concrete shapes and was found to be suitable for use in structural concrete.

Jan 1, 1968

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965

By Frank Chase, M. Terry Hoch, George Karabin, Joseph C. Zelanko, Christopher Mark

Pillar recovery continues to be a significant ground control hazard. During the past decade, 10 miners were killed during pillar extraction operations in southern West Virginia. Studies conducted during the past decade have identified a number of “risk factors” that can be used to evaluate pillar extraction plans: •Cut sequence •Final stump •Timber or Mobile Roof Supports •Roof bolting •Intersection span •Depth of cover •Roof quality •Age of workings For each of these factors, rock mechanics science suggests which alternative would be expected to be more risky. For example, numerical models were used to evaluate different cut sequences, and indicated that less roof convergence occurred with the outside lift method than with the Christmas tree in the particular environment simulated. For many of the risk factors, accident statistics confirm the science. One finding was that currently almost 70% of the retreat coal in southern WV is being mined with MRS. In contrast, timber supports were used in 70% of the past decade’s pillaring fatalities. This paper discusses each of the risk factors in turn, presents the relevant accident statistics, and shows how the risk factors can be combined to estimate the overall hazard. It also addresses the use of pillar design to minimize the risk of global stability hazards including squeezes, massive collapses, and bumps.

By G. R. Hopkins

"Refiners are generally considered solely as fuel producers, but actually they also comprise a group one of the largest consumers of fuel. For example, during the year 1929 the refineries-burned 51,544,000 barrels of oil as fuel, or the equivalent of over 5 per cent of the crude oil processed in that year. In addition enough other fuels - coal, natural gas, refinery or still gas, and petroleum coke - were utilized to raise the total fuel consumption based on B. t. u. equivalent to more than 10 per cent of the heat value in the total crude oil run to stills. Refineries utilize fuel chiefly as the heat-forming element distillation, but also under-boilers in the formation of steam used in refining, for the heating of buildings, and in the generation of electricity.In the early days of refining, the problem of fuel utilization and fuel economy was of scant importance to the refiners. Margins of profit were comparatively high and the major portion of the operatros1 attention was directed toward increasing their throughput. However, the keen competition that has prevailed in the refining industry over the past five years or more has taught the refiners that their expenses, one of the largest items of which is the cost of fuel, must be curtailed. Thus in 1925 the refiners used an average of 829,000 B. t. u. to refine a barrel of crude oil, wheras by 1929 this average had been reduced to 639,000 B. t. u., a decline of 23 per cent (see fig. 1)Since 1925 oil has ranked first as a refinery fuel (see fig. 2). The use of natural gas increased during 1926 and 1927 but declined in 1928 and 1929. On the other hand, the use of refinery gas has grown rapidly in importance. Coal has shown a steady decline in use at refineries since 1925. Petroleum coke has never supplied more than a very small fraction of the total fuel requirements, although there has been a steady increase in its use."

Sep 1, 1930

By S. Atallah

A survey was conducted relating to the current practices for the classification of hazardous locations in coal preparation plants. Several plants processing bituminous, anthracite and lignite coal in Pennsylvania, West Virginia, North Dakota, Colorado, Montana and Wyoming were visited. Coal preparation plant operations and designers as well as MESA inspectors were interviewed. The National Electrical Code was discussed with selected members of the NFPA committee and electrical equipment manufacturers. Data provided by MESA on fire and explosion accidents in coal preparation plants were examined. The requirements of the pertinent Federal Regulations, National Electrical Code, National Electrical Manufacturers Association and Underwriters' Laboratories were compared and evaluated. This report consists of two parts. Part I: "Analysis and Review" provides a summary of the findings. Part II: "Recommended Guidelines" consists of recommended uniform guidelines that may be used for interpreting the National Electrical Code as it applies to the classification of hazardous areas in coal preparation plants.

Jan 1, 1977

By S. J. Gerdemann

In support of its objective to improve mine safety, the Bureau of Mines has searched for better materials and systems to anchor roof bolts. TIlis report describes a study on the effects of mine waters upon accelerated gypsum, one of the materials under consideration. The accelerated gypsuw dissolved at an appreciable rate relative to an assumed 10-yr life span of a roof bolt. Surface orientation, initial ion concentration of a dissolving solution, and flow rate of the solu-tion had substantial effects on the dissolution rate. Factors such as water-cement ratio, accelerator content, wax capsule additions to the gypsum in cartridge-installed bolts, surface area, temperature, and curing duration had little effect. In an actual roof-bolt environment, dissolution will occur in static solutions to the solubility limit of gypsum (~2 giL) and cease, result-ing in minimal damage; but in flows of unsaturated solution as slow as 1 L per month, a loss of up to 10 pct will occur in 2 yr. Since miners cannot readily measure the flow or ion concentration of static-appearing water at every roof-bolt site, all such water must be assumed to be pure and flowing. It is recommended that gypsum-bonded roof bolts be confined to dry roofs only.

Jan 1, 1983

By Joseph S. Coffman

To determine the availability of manganese for metallurgical purposes from selected world resources, the Bureau of Mines evaluated the potential production of contained manganese in concentrates based on the demonstrated resources of 23 foreign and 8 domestic mines and deposits in 9 market economy countries. All but 2 of the 23 foreign deposits are operating mines; none of the domestic deposits are in operation. The demonstrated resources of the mines and deposits used in this study represent an in situ ore resource of approximately 2.2 billion tons," containing 780 million tons of manganese with a total recoverable production potential of 514 million tons of contained manganese in concentrates. The analyses of mines and deposits in this study indicate that about 213 million tons of the contained manganese (41 pct) is potentially available at a January 1981 constant dollar long-run total cost of up to $1.50 per long ton unit (22.4 lb, or 10.15 kg contained Mn), approximately 428 million tons (83 pet) is potentially available at a cost of about $1.75 or less, and 491 million tons (95 pet) is available at less than $3.30. The remaining 23 million tons, which is potentially available at much higher costs (about $8 to $35 per unit), represents the U.S. deposits. On an annual basis, with a cost range of up to $1.75 per long ton unit, the availability from currently operating mines would last at least 80 years based on 1980 world production data. Total manganese production costs are estimated to comprise mining-8 pet, beneficiation-3 pet, transportation-26 pet, and smelting-63 pet.

Jan 1, 1984