Search Documents

By Henry M. Harris

The roll forming of oxide powders was studied in a Bureau of Mines investigation to find the conditions and parameters required to make satisfactory ceramic strip. High-quality porous or dense alumina, zirconia, and porcelain shapes were made by sintering strip roll-formed at room temperature from powders containing minor amounts of binder and water. Strips with thicknesses of 0.04 to 0.08 inch and bulk densities from 40 to 90 percent of theoretical densities were made. The parameters most important to formability were particle size, condition of the powders, and roll gap. Other factors affecting quality were speed and surface condition of the rolls, amount and type of binder, water content, and sintering conditions. Ceramic strip was formed at rates up to 78 feet/minute, which is 13 to 23 times faster than reported by previous investigators, and forming was done in a simple and inexpensive roll unit. Reshaping the strip was possible by cutting, grinding, shearing, and stamping. The following innovations were developed that allow roll processing not normally possible with ceramic powders: (1) Fine-sized powders were made into strip by preparing these as partially sintered granules; (2) thick strip was formed by pressure feeding powders into the rolls; (3) flexible strip was made using a rubber-base bonding agent; (4) corrugated strip was formed on shaped rolls; and (5) porcelain strip was densified and reduced in thickness by rerolling while hot.

Jan 1, 1970

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By Steven W. Schmauch

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines Studied 25,340 acres of the 28,960-acre Twelve Mile Creek Wilderness Study Area (OR-003-162) in order to evaluate its identified mineral resources. The study area is located in Malheur County, OR, about 30 miles northwest of McDermitt, NV. The area is underlain by thick sequences of rhyolite to with lesser amounts of andesite and basalt flows. Bureau of Mines personnel reviewed pertinent literature, mining records, and examined the study area for possible mineral resources in geologically favorable sites. There are no organized mining districts and no record of past or current mining activity. Based on sample results, published literature and field observations, there are no identified mineral resources.

Jan 1, 1987

By Vance G. Leak

A technique for recovering copper and steel from metallic scrap has been developed by the Bureau of Mines based on preferential melting in molten salt baths at 1,150° to 1,250° C, The molten salt, preferably barium chloride or calcium chloride, both minimizes oxidation of the metals and promotes heat transfer. Cleanest separations (0.01 percent copper remaining in iron) have been achieved by pretreatment (dipping or spraying) with sodium sulphate or sodium silicate, which alters and coats the surface of the iron to inhibit the alloying or brazing with copper. An economic evaluation of the process was carried out on six combinations of sweating media and inhibiting reagents. On the basis of the postulated model, a cost of about $0.20 per pound of copper recovered has been determined for the sweating treatment operation.

Jan 1, 1973

Two coal seams were selected and the conceptual designs were based on the geological and physical conditions typical of these seams. As a result of the screening process presented below, the two coal seams selected were the Lower Kittanning Seam in central Cambria County, Pennsylvania and the Pittsburgh Seam in northwestern West Virginia and southwestern Pennsylvania. SELECTION PROCESS FIRST SCREENING OF LONGWALL OPERATIONS The list of longwall operations prepared in Phase I and included in the Phase I report, was used as the basis for a first screening. From this list it was determined which longwall operations were not in the Appalachian coal fields and not in a coal seam of the thickness range of 42 to 72 inches. The first screening eliminated 30 of the listed operations, leaving 48.

Jan 1, 1976

By Mohan K. Wali

This report, the first in a series of 13 reports, provides a summary of 11 major topics on which individual reports have been prepared. These major topics are: (a) Nature of coal mine spoils, topsoils, and unmined soils; (b) influence of macro- and microclimate on (c) plant production on spoils and topsoils; (d) prediction of aboveground biomass from plant cover; (c) mineral composition of plants; (f) controlled environment studies on plant growth response; (g) microbial communities (h) water chemistry and organism diversity of catchbasins; (i) vegetation and soil development on abandoned, and (j) topsoiled sites; and (k) viability and diversity of seed bank. Based on these investigations, general conclusions and some recommendations are presented.

Jan 1, 1982

To provide a flexible, low-maintenance, low-cost continuous mine air monitoring system as an alternative to conventional fixed-point, electronic monitoring systems. Background Continuous monitoring of mine air is highly desirable (and often required) not only to improve miner safety, but also to increase mine productivity. Continuous air monitoring systems can provide earl" warning of developing fires, excessive methane accumulation, reduced oxygen levels, and other developing problems in remote, inaccessible or sealed areas, and in active workings. Fixed-point, electronic systems require one Sensor for every gas to be measured at every defined monitoring location. As the number of monitoring locations increases, so does the cost, along with increases in the time required for routine maintenance and calibration of the sensor System cost also increases when monitoring locations are identified for mine areas requiring permissible electrical equipment.

Jan 1, 1988

By J. Dean Warner

Alaska contains many critical and strategic minerals that are scarce in the conterminous United States. Among these are tin, tantalum, and columbium. This Bureau of Mines report summarizes available data on the production, reserves, and occurrences of these minerals in Alaska. Alaska produces about 200,000 lb of tin per year, with historical production since 1901 estimated to have totaled 5,830,600 lb. Measured, indicated, and inferred tin reserves total over 140,000,000 Ib. Much of the tin production has been from the placer mines of the western Seward Peninsula; however, most of the reserves are in that area's lode deposits. Alaskan tin occurrences are part of a belt of tin mineralization that extends along the western coast of North and South America. The Alaskan portion of this "tin belt" comprises placer occurrences and lode occurrences of five major types: greisen, vein, skarn, pegmatite, and volcanogenic massive sulfide. Greisen and vein occurrences are the most abundant, but skarn deposits have historically been the most economically important. Columbium and tantalum have not been produced in Alaska; however, they may be recoverable as byproducts of tin, tungsten, gold, or uranium mining. Approximately 135,000 Ib of columbium oxide (Cb205) are inferred within the Tofty placer deposits in the Manley Hot Springs district.

Jan 1, 1985

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

By Sean Gallagher, John R. Bartels, Dean H. Ambrose

Remote operation of continuous miners has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred when using remote controls. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory examined the workplace relationships between continuous miner operators and various tramming modes of the equipment using motion captured data, predicted operator response times, and field- of- view data to determine causes of operator-machine struck-by events in a virtual mine environment. Factors studied included machine speed, direction of escape, operator facing orientation relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck. It is hoped that this data will provide an improved rationale for operator positioning for remotely operated continuous miners.

By Harry A. Schrecengost

The Bureau of Mines has found considerable lack of uniformity in style and content of record books used for reporting the results of examinations made by coal-mine officials. These books range from elaborate forms designed for specific examining and operating procedures at certain large mines to simple composition books, tablets, and pocket-style notebooks at other mines. Examination of thousands of these record books discloses that the reports of many examinations are so brief and so poorly worded that they cannot be understood readily. The contents, in some instances, appear to be deliberately ambiguous. The value of keeping accurate accounts of safety inspections in coal mines is often underestimated. Well-kept records reflect managerial attitude and indicate well-governed operations as well as training of official personnel to conform to considered policy and regulations and if necessary, may serve as documentary evidence to protect the mine officials and the operators.

Jan 1, 1962

Three complete connector assemblies and six separate contacts were submitted to a series of tests to establish the connectors permissibility and compliance with U. S. Bureau of Mines research Contract #H 0110423 D.C. portion. Test Procedure TPC-0118 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the direct current connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1974

By H. L. Burmeister

This is one of a series of publications by the Bureau of Mines dealing with mining methods and costs at representative operations in the United States. The report describes all phases of the mining methods for the open-pit operation and milling practices employed at the Vermont Asbestos Mines in Lamoille and Orleans counties, Vermont. A brief history of discovery and development of these asbestos deposits is given, and the ore deposits are described. Methods employed in exploration, sampling, and estimation of tonnage and grade are outlined. A breakdown of available cost figures is summarized in the last section. All asbestos ore produced in this area has been won by the use of surface-mining methods. Two quarries, the Lowell and the "C" Area, are in operation. The quarries combined are producing and the mill is processing approximately 3,500 tons of ore per 3-shift day The average 40,000 tons of crysotile asbestos fiber produced at this plant annually accounted for 96 to 98 percent of the total fiber produced in the United States in 1958. The mine is located (fig. 1) approximately 4 miles north of Eden Mills village on the southeastern flank of Belvidere Mountain (fig. 2).

Jan 1, 1962

By W. R. Hardwick

This information circular describes open-pit mining methods and practices of the Bagdad Copper Corp., Yavapai County, Ariz. It is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A brief history of the Eureka district and of early developments at the [gdad] mine is given, and the are deposit is described with particular emphasis on those characteristics (physical, economic, or engineering) that affected the choice of mining methods. Prospecting, exploration, and sampling and estimating the tonnage and grade are outlined. Development of the open-pit mine is shown. Mining methods, including breaking ground, primary drilling and blasting, secondary drilling and blasting, loading, transportation, engineering, and operating control, are described. A brief summary of mining equipment is given. Percentage of extraction, production rate, mine drainage and water supply, wage, contract, and bonus systems, safety and fire prevention, and the processing plant also are described. The last section gives a breakdown of such costs as are available for publication.

Jan 1, 1959

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li2O-A1203-4Si02) a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Rills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade e deposits it s in North Carolina. The theoretical lithia (Li20) content of spodumene is 8.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By C. R. Sponsler, O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Research (CFR) Committee of the Coordinating Research Coouncil (CRC) 4/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36. 5/ Further reports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941. 5/ reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed. 5/The present report presents analytical data for samples, representing the products of approximately 100 companies. Most of the samples represented in this report were obtained during December 1)55 and January 194o. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gasoline are not considered adequate to represent this type of motor fuel, data for the analyses have not been averaged, but the individual items are tabulated. The number of samples, items, and brands comprising each group is as follows:Regular-price, 1,958 samples, 317 items, and 96 brands; premium-price, 1, samples, 292 items, and 85 brands; third-grade, 58 samples, 22 items, and 14 brands. The meanings of these terms as used in the surveys are as follows;"

Jul 1, 1946

By L. Cheng

This report presents the results of a Bureau of Mines laboratory investigation of the effect of water sprays in reducing respirable dust that escaped the face area of a full-scale wooden model of a mine en-try containing a wooden model of a ripper-type continuous mining machine and exhaust brattice. Areas examined were (a) the general effectiveness of a low-pressure water spray system mounted on top of the mining machine boom, a high-pressure spray system mounted under the boom, and the combined top-and bottom-spray systems, and (b) the effect of these three spray systems on the capture of coal dust particles of different sizes. Dust was injected into a sump cavity at the face. Airborne respirable dust concentration was mea-sured behind the brattice with a personal sampler and cyclone, and particle size distribution was mea-sured with a cascade impactor. When used alone, the top-spray system captured about 55 pct of the respirable dust in the face area and the bottom-spray system captured 60 pct; the capture efficiency of each system is decreased when they are used simultaneously. From a mass-concentration viewpoint, each spray system preferentially captures larger dust particles.

Jan 1, 1988

By H. A. Wright

This report assesses the economic, legal, institutional and technical factors that affect the current and future status of implementation of mine monitoring systems in the United States. It begins with a description of a poll of the Mining Production Research Committee and the Mine Monitoring and Communications Committee of Bituminous Coal Research that was conducted to establish industry monitoring needs and constraints. Existing systems in the United States and foreign countries are then reviewed and compared with the requirements set forth by the industry committees. At the same time, state and federal mining laws are reviewed, and equipment currently available from suppliers of mine monitoring systems and components is discussed. A framework for cost/benefit analysis is established and a series of case examples for various monitoring functions are presented. The total values of the market for mine monitoring systems in 1980 and 1990 are estimated on the basis of industry statistics and system cost estimates.

Jan 1, 1982

By B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Bankhead mine of the Cane Creek Coal Mining Co. is in the central part of Walker County, Ala., 4 miles south of Jasper. The Mary Lee bed in this part of the State yields a practically free-burning coal which is marketed as a. steam-raising and domestic fuel. As mined, the coal ordinarily contains ash-forming impurities to an extent that makes it necessary to treat the coal by some washing process before it is marketed. At present the Bank-head coal coarser than 3-1/2 inch is hand-picked and the coal finer than 3-1/2 inch is washed in two single-compartment jigsThis paper contains the result of screen-sizing and float-and-sink tests on a representative sample of the run-of-mine coal and the results of tests made to show the amount of coal liberated from impurities by crushing the coarser sizes. .This report is one of a series on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the coal producers of Alabama.SAMPLING AT THE MINE'The Mary Lee bed at Bankhead consists of two benches separated by a rock parting which varies in thickness from place to place in the mine. The top bench has a very uniform thick-nest; throughout the workings and yields about 65.0 per cent of the output. The bottom bench varies greatly in thickness and in nary places becomes too thin to work at a. profit. The sample for the washability study was taken underground at a place which was typical of the mine as a whole. In taking the sample the working face was squared up and a representative section out from each bench. Care was taken to secure a, quantity of coal from each bench proportional to the quantity contributed to the mine output. The rock parting as gobbed in accordance with the usual mining practice. The total sample taken weighed 3 tons."

May 1, 1933

By Richard H. Bares

This report describes the purpose and application of seventeen statistical and mathematical procedures used in a series of studies made in the project ?A Systems Approach to the Reclamation of Strip-Mined Areas in North Dakota". The objective is to help readers better understand the utility of these procedures.

Jan 1, 1982