Search Documents

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931

By Mark R. Pettitt

The development of fire hazard criteria for noise control products in underground coal mines are presented. Qualifying requisites of the criteria include maintaining miners' safety, allowing for maximum use of noise control products, and economic feasibility. The burning process is analyzed for its relationship to fire hazard criteria developed by NASA and the FAA, and the mine environment is analyzed in conjunction with the end-use applications of noise control products. Also, the interim fire hazard specification developed by MSHA is appraised as it applies to end-use applications of noise control products. From these analyses and a literature survey, fire hazard criteria are developed. They include an initial screening procedure that evaluates the level of flammability testing required. Fire tests that may be indicated are the Vertical Flame Test, the Ignition Temperature Test, and the 25-Foot Tunnel Test.

Jan 1, 1983

By Carl Belser

This report on tungsten in Ouray, San Juan, and San Miguel Counties, Colo., is one of a series describing results of studies on the tungsten potentialities in Region III, Bureau of Mines. The San Juan tungsten deposits occur in an area of 250 square miles, centering near the common corner of Ouray, San Juan, and San Miguel Counties (fig. 1). Field work supporting these studies was done in May 1954. Bureau of Mines reports prepared from investigations made during World War II and under the Defense Production Act of 1950 were reviewed.

Jan 1, 1956

By W. W. Adams, T. D. Lawrence

"Despite the manpower shortage and other difficulties of operation in war time, the National Safety Competition of 1943 for the promotion of safety in the mineral industries of the United States was notable for having a larger enrollment of mines and quarries than in any other year except 1941 and 1942 since the yearly safety contests were inaugurated in 1925. The competition was also notable for having a larger number of man-hours represented by the competing companies than in any previous contest except that of 1942. The ratio of accidents and days of disability resulting from accidents to the number of man-hours of work performed was more favorable than in 1942; the accident-frequency rate was lower and therefore better than in 13 of the 19 years during which the annual safety competitions have been conducted, and the accident-severity rate was better than in 16 of the 19 years.The National Safety Competition is a yearly safety contest conducted by the Bureau of Mines, United States Department of the Interior. Companies that win first place in their respective group in the contest are awarded a bronze trophy, ""The Sentinels of Safety,"" which is provided by THE EXPLOSIVES ENGINEER magazine. Competing companies are segregated into six groups: Underground bituminous-coal mines, underground anthracite mines (in Pennsylvania), underground metal mines, underground nonmetallic-mineral mines, open-cut mines (without regard to kind of mineral produced), and open quarries (without regard to kind of stone produced). The bronze trophies are retained by the six winning companies for 1 year and are then transferred to the winners of the succeeding year's contest. On the pedestal of each trophy is engraved the names of the winners of the trophy. With the award of the trophies for 1943, therefore, the pedestal of each trophy bears the names of 19 winners."

Aug 1, 1944

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1951

By Kim B. Shedd

The U.S. Bureau of Mines Particulate Mineralogy Unit examined the habits of six zeolite minerals commonly occurring in domestic zeolite deposits. Mineral habit is of interest because current theory on the potential for sarcoma production in test animals emphasizes the size and shape of mineral particles, without regard to composition or structure. A scanning electron microscopic study revealed that, of these six minerals, only mordenite and erionite crystallized in acicular to fibrous habits, The fibrous varieties of these two minerals were characterized by size and shape on the transmission electron microscope, and their dimensions were compared with those of asbestos and amphibole cleavage fragments. When comminuted, these two minerals possess "fibrosity indices" similar to those of amphibole cleavage fragments. One sample, a rare woolly erionite, has uniform widths, large aspect ratios, and a "fibrosity index" similar to those of asbestos.

Jan 1, 1982

By R. W. Hiteshue, C. O. Hawk, H. H. Ginsberg, M. D. Schlesinger

The Bureau of Mines studied single - step catalytic vapor - phase hydrogenation of oils derived from coal and oil shale . Treatment of middle oil , from hydrogenation of bituminous coal , gave good yields of gasoline with a German - made molybdenum- zinc - chromium catalyst . The Bureau also achieved good results with duplicates of this catalyst made from domestic raw materials . In one set of experiments with the German catalyst , 38 to 52 wt pct of feed was converted to gasoline . The total liquid product was 91 to 98 wt pct of the feed . Not all this gasoline can be claimed as production , however , because about 20 pct of the feed was in the gasoline range , and part of it undoubtedly survived the hydrocracking treatment . Hydrogenation of crude shale oil in the presence of cobalt molybdate catalyst produced a total liquid product of 89 wt pct of feed . The hydrogenation converted 27 wt pct of feed to gasoline and 44 wt pct of feed to diesel fuel . The remaining liquid product , 18 wt pct of feed , was residue boiling above diesel fuel . The gasoline was of poor quality , with an octane number of 39.1 . The overall product seemed a suitable feed stock for a conventional refining operation . Coker distillate hydrogenation , using a cobalt molybdate catalyst , gave a total liquid product of 97 vol pct of feed ; of this product 60 vol pct was jet fuel and 40 vol pct was diesel fuel . High nitrogen and sulfur in all three of these raw materials severely poison the usual refining catalysts . Thus , the common objective in these

Jan 1, 1964

By G. F. Kuncir

The analysis summarized herein evaluates the Bureau of Mines Program for Advancing Mining Technology Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings, environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

By Donald W. Ross

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk—type sagger sponge iron, has an excellent reputation as a superior furnace feed wherever high—grade steels are made. The general procedure for making brickyard sponge iron was described frequently in Swedish technical journals prior to 1932 and at that time consisted in filling clay refractory containers, called saggers, with a super-concentrate of Gellivare magnetite plus the necessary amount of solid reducing agent and desulfurizer and then firing in a Hoffmann ring furnace, as used in the ceramic industry.The early Swedish publications describe two types of brickyard sponge iron: (1) An inferior high-sulfur product obtained by mixing the ore and reducing agent, and (2) a high-grade low-sulfur product in the form of coherent disks 7 to 9 inches in diameter and 1 to 1-1/2 inches thick made by the saggers with alternate layers of solid-fuel reducr and of uniaxed ore."

Sep 1, 1945

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

The Florida phosphate industry, which supplies about three-quarters of the domestic phosphate fertilizer, produces tremendous volumes of phosphatic clay wastes (slimes). These clays retain a high percentage of water for extended periods of time. The clays also pose an environmental hazard because the disposal technique involves aboveground storage behind earthen dams. Although much research has been undertaken by numerous organizations to dewater slime, no completely satisfactory solution has been developed. In June 1972, a cooperative effort by the Federal Bureau of Mines and the Florida phosphate mining industry was initiated to develop a solution for dewatering the Florida phosphatic slimes. This report discusses various aspects of the slimes problem, reviews past research, makes recommendations for future research, and includes a bibliography of references and patents dealing with the subject.

Jan 1, 1975

By A. U. Miller

For many years Illinois has been one of the leading coal producers in the United States and as such its safety record has compared very well with the other large coal producing States , both in tons produced and millions of man -hours of exposure per fatal accident . ( See Table 25 in Bureau of Mines Bulletin 293. ) During the 10-year period from 1917 to 1926 , inclusive , the average production in the United States per fatal accident was 278 , 109 tons . The aver age for the State of Illinois for the same period was 409,249 tons . Illinois produced 450,464 tons per fatal accident, and in 1928 produced 390,630, tons , or an average of 419,721 tons for the 12- year period from 1917 to 1928 , inclusive . In 1927 During the year 1929 , the shipping mines of the State made a decided improvement in their record over any previous year . Table 1 shows the monthly production and the tons produced per fatal accident . During 1928 and 1929 safety work was actively carried on in Illinois . Safety meetings were held with mine officials , representatives of the State. De partment of Mines , and the United States Bureau of Mines . At these meetings mine hazards and accidents were discussed and remedies suggested for : their elimination in the future . It is believed that first - aid training was to a considerable extent instrumental in reducing accidents and in making the good safety records in Illinois during 1928 and 1929. During these years ( as well as in 1926 and 1927 to a somewhat less extont ) en intensive rirst-aid training campaign was con ducted in Illinois by the officials and members of the United Mine Workers of America , coal companies, State Department of Mines and Minerals , and the U. S. Bureau of Mines , Every first -aid class was made a safety meeting ; where accidents and general safety were discussed freely while teaching first aid. During this time , anproximately 25,000 persons were trained in first aid, and 17 coal companies were issued certificates for having 100 per cent of their employees. trained in first aid. Since January 1 , 1926 , more than 40,000 have received first -aid training in and around Illinois mines , and including those who received training previous to this date , it is believed that at least 90 per cent of the miners in Illinois have received first -aid training . This state ment is based on the fact that the labor turnover in Illinois is not large .

Apr 1, 1931

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By Virgil J. Stachura

The Bureau of Mines has investigated techniques and instrumentation that measure accurately the airblast overpressures from surface mine blasting. The results include equivalencies between broadband research instrumentation and commercially available impulse precision sound levels meters measuring: root-mean-square, peak, fast, slow, impulse, A and C weighting, C-weighted sound exposure level (CSEL), and "linear" (flat) response. These values were obtained from field measurements and broadband FM tape recordings of production blasts at area and contour coal mines, limestones quarries, and iron mines. Frequency response was determined for 14 commercial systems.

Jan 1, 1981

By Roger J. Morrell

Bureau of Mines laboratory experiments with reduced scale cutter and cutter forces were performed to (1) define the fundamental relationships governing disk cutter performance and (2) to develop a method of predicting disk cutter performance in soft, medium, and hard rocks. The rock cutting experiments were performed in four igneous and metamorphic rocks that ranged in compressive strength from 38,000 to 67,000 psi. A special testing machine called a linear cutter apparatus (LCA) was used to load and traverse a free rolling disk cutter across a smooth rock surface. Each pass of the disk produced a single crater, and runs were spaced to avoid breakage between craters. During each run the normal and tangential cutter forces were measured and recorded. The soft and medium rock data were obtained from previous Bureau experiments with disk cutters. Crater depth, tangential cutter force, crater volume, specific energy versus normal cutter force, and crater width versus depth are defined within this study. With the use of standard physical properties, performance prediction equations were developed using stepwise linear regression analysis techniques. A method of using these prediction equations to calculate the boring rate, the cutter spacing, and the torque and energy requirements of a full-scale boring machine was also developed.

Jan 1, 1974

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982

By P. G. Guest

"INTRODUCTION Need for More information on Spark IgnitionMany questions have yet to be answered more completely concerning the ignition of flammable gases and vapors by electric sparks. Among these one might mention the following: How do the mixture limits for ignition by sparks and by other means compare? Are the most explosive mixtures of the gases the most easily ignited? How ""hot"" must the spark be or what is the minimum energy required for ignition? Does the electric spark act merely as a source of thermal energy or do aggregations of ions, electrons, and metastable atoms formed during and just before the spark play an important part in promoting chemical reactions that ultimately lead to ignition? It is possible for ignition to occur as a result of a silent or brush discharge? How do the ignition energies with single and rapidly recurring sparks differ? What is the relative effectiveness of long, tenuous sparks in ignition as compared with intense, short-gap sparks of equal energy? What is the influence of the material, size, and shape of the spark electrodes? Does the energy for ignition change noticeably with moderate changes in pressure and temperature of an enclosed gas mixture? What order of lag exists between the occurrence of an incendiary spark and the first evidence of flame propagation? What part of a spark in space and time is most effective in producing ignition? Answers to these questions bear directly on the general problem of flame initiation and propagation and, if sufficiently comprehensive, should contribute much to an understanding of the actual mechanism of combustion."

May 1, 1944

By G. W. Jones

In a previous report&apos;/ results were given and a method outlined whereby from a knowledge of the composition of the natural gas and of the inflammability limits of the individual constituents composing the natural gas, the limits of inflammability of natural gas and air mixtures could be closely calculated. This method is based on the application of Le Chatelier&apos;s law as modified by Coward, Carpenter and Payman,5/ to apply to a mixture of any number of combustible gases. This law must not be used indiscriminately, because many exceptions have been found. For example, when ethylene, acetylene, hydrogen sulphide, or chlorinated hydrocarbons are present the law may not hold. For a discussion of the many exceptions which have been found, reference should be made to a report by Coward and Jones.6/

Jan 1, 1933

By J. F. Barkley

"The fly-ash problem of the smoke-abatement engineer - who now might well be titled, ""Smoke and Fly-Ash Abatement Engineer"" - starts with the necessity for him to know what fly ash really is, what plants really create it, and how much is being created. Fly ash in this connection may be defined as all solid particles emitted to the atmosphere as a result of the combustion of fuel.COMPOSITION OF FLY ASHMuch can be learned about fly ash by studying samples with a strong magnifying glass or, preferably, a high-power microscope. As an example, figure 1 is a photomicrograph of an underfeed-stoker fly ash weighing 23.7 pounds per cubic foot, which passed a baffle-type cinder catcher and was caught by a Cottrell precipitator. Figure 2 shows a similar fly ash made at a higher stoker rating and weighing 36.2 pounds per cubic foot. The lighter ash contains more light, unconsolidated ash than the heavier. In both instances some of the ash has been fused to a glass, as is indicated by the spherical particles resembling marbles; however, the heavier dust contains more and larger spheres. With the faster burning and higher air pressures occurring at the higher burning rates, more of the larger fused spheres reached the precipitator.Such studies of fly ash frequently make possible correct determination of its source. For example, the Supreme Court Building, one of the finest of the Federal buildings in Washington, was having considerable difficulty with fly ash from some outside plant. It was thought to come from a nearby apartment house. A fly-ash trap was installed there, and care was taken in the operation of their underfeed stokers. The fly-ash nuisance continued. Microscopic examination of the fly ash found about the building compared with samples taken from the stack of the apartment house showed to the surprise of the accusing building superintendent that the present source was elsewhere. By the same means, the source was found to be a plant about ore-half mile away."

Sep 1, 1939