Search Documents

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By Jeffrey P. Schubert

The study site in northeastern Illinois underwent surface mining for coal in 1943 and was reclaimed by the state of Illinois in 1972-1973. Additional soil amendments and seed were applied to the spoil surface in 1975-1980. Previous studies in 1975-1978 had shown that the surface spoil materials and five final-cut lakes at the site were quite acidic and the lakes contained high concentrations of sulfate and dissolved metals. Surface runoff water from monitoring plots in 1976 were only moderately acidic and the mean concentrations of most dissolved metals and sulfate in the runoff waters were less than 25% of the concentrations found in Lake B. By 1980, vegetation had become well established over most of the mined area. However, the five final-cut lakes (Lakes A-E) remained acidic. The purpose of the study reported here was to determine the physical and geochemical subsurface conditions of the spoil materials, the hydrologic flow system within the spoils, and the magnitude of acidic spoil leachate migration into the lakes and into the wetland prairie north of the mine site. Lakes A, B, C, and E were still very acidic in 1980-1981 (pH range: 2.9-3.4; aridity range: 110-860 mg/L as CaCO3). Lake B had the worst water quality, with mean concentrations of dissolved aluminum, iron, manganese, and sulfate of 75, 25, 37, and 3340 mg/L, respectively. Shallow groundwaters in spoil materials around Lake B had a lower pH and about two to four times greater concentrations of aridity, aluminum, manganese, zinc, and other metals and nearly 20 times greater dissolved iron than the water in Lake B. The shallow groundwaters in undisturbed soils and bedrock 10-30 m north of the mine site spoils generally were alkaline, but did contain occasional moderately high sulfate and metal concentrations. Pumping tests and recovery tests conducted in piezometers showed hydraulic conductivities of spoil materials ranging from less than 10- to 10-5 m/s; hydraulic conductivities of natural soils and bedrock were measured between 10-10 to 10-7 m/s. Water levels in spoil materials increased rapidly in response to rainstorm events and the recession curves were relatively quick to decline, lasting only two or three days. Quick infiltration of rainfall into the spoil surface and percolation down to the water table caused a rise in groundwater levels and movement of spoil groundwater into the lakes. This groundwater component in the lake water budgets could account for most of the water quality problems occurring in the acid lakes.

Jan 1, 1984

By Gerald W. Elger

This report compares the quality of zirconium metal prepared by batch reduction of zirconium tetrachloride by (1) sodium, (2) magnesium, and (3) mixtures of sodium and magnesium. Criteria for quality are based on chemical analyses and hardness testing of zirconium arc-melted from sponge. The best quality zirconium with respect to low oxygen content and hardness numbers was prepared by reaction of zirconium tetrachloride with a mixture of sodium and magnesium. It was found that this reaction could be successfully carried out by two methods: (1) addition of sodium and magnesium before the initial reaction and (2) periodic injection of sodium during reaction of zirconium tetrachloride with magnesium. The largest quantity of metal was found to be recovered from experiments in which a mixture of sodium and magnesium was used. Magnesium appeared to be a better reductant than sodium because magnesium-reduced zirconium contained less oxygen and exhibited lower hardness numbers than sodium-reduced metal.

Jan 1, 1962

By Anthony Edey

This report describes work performed and results obtained for the technical and economic feasibility study of oil production by mining methods. The characteristics of oil fields which would make them amenable to mining techniques were identified. An inventory of known U.S. oil fields that offer this potential was collated. This was further divided into fields having potential for underground and surface mining systems development. Several candidate fields that fit particular underground and surface mining system types were then selected. Conceptual mining systems were designed for the selected fields. Five underground and four surface methods were chosen. Costs of oil production were estimated for these selections. The impact of oil mining an the environment was also considered.

Jan 1, 1978

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By Richard I. Barnhisel

At the Sinclair Study Site it was found that the deeper the soil the greater the yield of corn, soybeans, wheat, alfalfa, and timothy. Yields at this location were generally lower than those at the Alston Surface Mine. At Alston the non-prime land treatments generally produced greater yields for all crops than did the prime farmland treatments, however, the intermediate soil thickness, 20 cm topsoil over 40 cm of subsoil, gave the best yields, provided it's subsoil had been limed. From a chemical point of view, acidic spoils do not need to be buried by 120 cm or 4 feet of soil, provided adequate lime is applied to these spoils as a barrier prior to placement of good quality topsoil and only forage crops are to be grown. The burial depth must be increased to as much as 75 cm when grain crops such as corn or soybeans are to be grown. This response to burial depth appears to be related to water storage needed by the crop and not due to toxic effects of the spoils. A conventional farm tractor-mounted subsoiler increased yields of soybeans and corn the first one or two years, but the effect was diminished with time. Subsoiling did not produce significant increases for alfalfa or wheat. However, ripping with a bulldozer produced significant yield responses, especially for corn and soybeans, that have lasted for at least three years. The ripping effectively reduced the bulk density at least within the zones through which the ripper had passed. Liming the upper 20 cm of subsoil significantly increased yields of alfalfa, corn, and soybeans. There also appeared to be an interaction between this lime treatment and soil depth. Yields of some grain and forage crops may be high enough to meet target levels for bond release for prime farmland. Based on the present study, one should not expect corn yields to be high enough to meet bond release. This statement should not be considered final since the experiment is not complete.

Jan 1, 1983

By R. V. Ramani

In this report, the application and limitation of the various equipment available for surface coal mining are discussed. The correction factors for adjusting equipment performance arising from machine design, material characteristics, and modes of operation are presented. Engineering design, pit layout and equipment selection are discussed with mathematical derivations. Two computer programs (SMCALC and SMRES) have been written to aid in pit design and equipment selection. The Strip Mine Calculation Program (SMCALC) can be used to select the bucket size and reach of shovels and draglines for various pit widths. It will also calculate the number of drills, loading shovels, trucks and bulldozers needed to achieve a production target. The Surface Mine Reclamation Equipment Selector (SMRES) can be used to select the number of bulldozers, scrapers and front-end loaders needed to achieve the desired production.

Jan 1, 1976

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

By M. M. Fine

A process for simultaneously reducing and indurating iron are pellets was developed by Bureau of Mines laboratory research and confirmed on a continuous pilot plant basis. Moist iron are concentrate was balled, mixed with solid reductant, and heated at about 1,100° to 1,150° C. On a small scale, a variety of concentrates and fuels were utilized successfully. The pilot rotary kiln tests were limited to natural magnetite, synthetic magnetite, lignite, and anthracite. In both cases, partially reduced pellets with excellent physical properties were regularly produced with average analyses of at least 80 percent total iron and 60 percent or more metallic iron. These and other prereduced pellets were smelted in the Bureau's experimental blast furnace facility, Bruceton, Pa. With prereduced spheres comprising 85 percent of the burden, the coke rate was approximately half that with standard oxide pellets and production of hot metal was increased by 75 percent. Economic appraisal of the cost of making hot metal indicates that reduced pellets could be more profitable than any other iron raw material in both investment capital and daily cost of operation.

Jan 1, 1970

By Lloyd A. Morley

This Bureau of Mines publication presents a comprehensive review of mine electrical power-system theory and practice. It discusses fundamental theory and the vital aspects to be considered in planning and designing mine electrical power systems. The report is divided into three major sections. The first presents the history of electricity in mining and the fundamentals of electrical phenomena and components. The second focuses on power-system components: motors, grounding systems, cables, and protective equipment and devices. The final section includes mine power-center equipment, switchhouses and substations, batteries, and mine maintenance.

Jan 1, 2003

By Martin H. Stanczyk

The direct dissolution of a typical zinc sulfide flotation concentrate by elevated temperature and pressure leaching was investigated. The concentrate assayed about 55 percent Zn, 32 percent S, 6 percent Fe, and 1 percent Pb and contained minor quantities of copper and precious metals. The influence of various factors on the dissolution of the zinc in acidic and ammoniacal pulps when using oxygen as the oxidant was determined. The tests revealed that the sphalerite was difficult to oxidize. Complete dissolution of the mineral required vigorous and intimate nixing of the gaseous, liquid, and sold phases. The addition of pyrite or sulfuric acid to water slurries of the concentrate was required to obtain a high zinc extraction when leaching under acidic conditions. The quantity of pyrite and acid used was about 0.125 and 0.25 pound, respectively, per pound of zinc sulfide contained in the leach charge. In tests with acid, about 96 percent of the zinc was extracted from the concentrate in 1 hour at 200° C. when the oxygen partial pressure was 75 pounds per square inch gage or higher. Leaching with a continuous flow of air as the oxidant gave results that were almost as good as those obtained when oxygen was used, In tests with air fed through the autoclave at 320 liters per hour, 95 percent of the zinc was dissolved in 1 hour, Acid leach solutions assaying approximately 58 grams Zn per liter and containing Fe, Ni, Cr, and Cu impurities were produced in the better tests. The leached residue consisted essentially of red iron oxide together with substantially all of the lead and precious metals.

Jan 1, 1961

By Arthur Matzick

The oil shale from the Mahogany zone of the Green River formation in northwestern Colorado has the greatest potential in the United States for early utilization. A large reserve of adequately rich shale is available to support a sizable industry, and crushing of tremendous tonnages will be required if conventional processing methods are used. This report presents Bureau of Mines data on crushing experiments, physical properties, and related information for Colorado oil shale. Among the properties important to crushing are slab-forming tendency, resilience, slippery character of the richer grades, and heterogeneous nature of an average charge of Colorado oil shale.

Jan 1, 1960

By J. H. Field

Synthesis of hydrocarbons by the Fischer-Tropsch reaction in a hot-gas- recycle system was demonstrated to be technically feasible. This project was undertaken, by the Bureau of Mines, to determine if the system was operable and to ascertain the optimum conditions for the production of gasoline. Carbon steel turnings packed with a void volume from 88 to 90 pct. were satisfactory catalysts, but steel catalysts with greater void volume, either turnings or steel wool, were not as active. Good temperature control with a pressure drop of less than 0.5 pounds per square inch (p.s,i,) per foot of catalyst bed of turnings was obtained by operating with a recycle to fresh feed ratio of 20 and by splitting the total gas flaw and injecting portions into the reactor at different entry ports.

Jan 1, 1961

By D. R. Wilburn

The Bureau of Mines investigated the potential availability of magnesium from 45 properties in market economy countries (MEC's). The 38 significant deposits evaluated have demonstrated resources of approximately 29 billion short tons (st) magnesium-bearing material containing 416 million short tons (MMst) magnesium oxide (MgO). Using data it gathered, the Bureau determined the magnesium production potential for each property including a 15-pct rate of return on invested capital. Total and annual availability assessments for the next 30 yr were completed for magnesium (Mg) metal, deadburned MgO, and caustic calcined MgO. At a January 1984 market price of $1.34/Ib Mg metal, the properties evaluated could economically produce an estimated 13 MMst Mg metal. At a market price of $400/st nonmetal magnesium product, these properties could economically produce 109 MMst deadburned MgO and 43 MMst caustic MgO. These properties could produce approximately 301,000 st Mg metal, 3.0 MMst deadburned MgO, and 430,000 st caustic MgO annually at current full production levels and 1984 market prices until at least the year 2000. Total 1984 MEC production assessed in this study was 153,000 st Mg metal and 4.3 MMst nonmetallic MgO products.

Jan 1, 1986

By J. H. Welsh

This Bureau of Mines report presents guidelines to be considered in the design, installation, and operation of environmental mine monitoring systems in underground coal mines so as to enhance safety in the U.S. mining industry. A review of the current status of mine monitoring in the United States is also provided.

Jan 1, 1987

By C. V. Jude

This U. S. Bureau of Mines (USBM) report presents results of stress analyses and field observations to investigate the effects of elevated trench drifts on the structural stability of rock mass zones surrounding a production draw drift in a mine utilizing a mechanized load-haul-dump (LHD) trench undercut panel caving system. A two-dimensional boundary-element mine stress model was developed to predict the locations and extent of damaged rock mass zones surrounding draw drifts where adjacent, parallel trench drifts are either elevated or not elevated above the LHD production draw drift level. A Mohr-Coulomb shear-failure criterion was obtained directly from in situ borehole shear test data. Hock-Brown shear-failure parameter values were computed from borehole-shear and triaxial test data. A procedure is described to estimate these parameters when a rock mass rating (RMR) value and triaxial data on intact samples exist, and no borehole shear test data exist Results indicate that trench drifts, elevated to the level equal to the height of the LHD production draw drift, would not minimize material damage nor significantly enhance the stability of rib and crown pillar zones surrounding production draw drifts in the mechanized LHD trench undercut caving panel investigated at this mine.

Jan 1, 2010

By B. W. Madsen

Research by the Bureau of Mines has shown that treatment of open pit waste by crushing and sizing followed by flotation of the fines and leaching the coarse fraction results in greater metal recoveries than obtained by leaching only. Tests with a chalcocite-bearing quartz monzonite mine waste sample that had been crushed to minus 6 inches and screened on 1/2 inch yielded copper and silver recoveries of 71 and 22 percent, respectively, by the combined flotation-leaching process, compared with 48 percent of the copper and no silver recovered leaching the run-of-mine material. Copper was more readily leached from the coarse material with the minus 1/2-inch fines removed than from material with the fines included. The improved leaching was attributed to improved permeability and the associated improved circulation of air to the interior of the ore column. Cost estimates showed that the proposed intensive treatment of mine waste will require a greater capital investment and higher annual operating costs than conventional milling and dump leaching process. However, the income from the additional metal production offsets the increase in capital investment and operating costs, resulting in additional profit.

Jan 1, 1975

By Joseph M. Pugliese

This work was done by the Bureau of Mines to provide quarry operators with an uncomplicated, first-approximation method for designing blast patterns, considering geologic structure, and to show the valid use of the technique by comparing drill and blast pattern dimensions used in the quarry with those determined by the presented method. The author visited 12 limestone and dolomite quarries in Ohio (Adam, Crawford, and Highland Counties), Wisconsin (Milwaukee, Racine, and Waukesha Counties), and Minnesota (Fillmore, Olmsted, and Wabasha Counties); observed the blasting practices; studied the major geologic features; and after discussion with the quarry managers, foremen, and blasters, compared the quarry blasting patterns with those as calculated by the empirical formulas (after R. L. Ash), with geologic structural considerations. When geologic structure such as bedding, jointing, folding, and caves, as well as explosive properties and field performance characteristics are accounted for in a manner suggested by the research, the presented empirical formulas may be used as a good first approximation. The included steps in planning a blast design and generalized blast patterns should be of help to the quarry operator. Design changes are recommended for those quarries where problems are occurring.

Jan 1, 1972

By Robert B. McElwaine

"The demand for barite has increased greatly in the last 10 years, especially during World War II. Depletion of oil reserves and subsequent increase in deep drilling created a heavy demand by the oil industry for barite to be used as drilling mud. The great increase in demand for barite gave impetus to the development of a, deposit of impure barite near, Magnet Cove in Hot Spring County, Ark.The critical condition of the national barite supply early in 1944 led the War Production Board to recommend that the Bureau of Mines attempt to prove the existence of a large reserve tonnage of barite in the Magnet Cove area and arch for new deposits. To carry out this program, the Bureau explored on newly reported. Barite deposits in southern Montgomery County, Ark. The Gap Mountain, Fancy Hill, and Sulphur Mountain barite deposits were investigated. Eight diamond core-drill holes and 1,336 linear feet of surface trenching were completed, and barite samples obtained were analyzed, A study of the Montgomery County barnse district indicates that the lenticular bodies of barite replace a favorable host rock near the base of the Stanley shale formation. Barite is exposed along the side of anticlinal mountains where erosion has truncated the beds on the limbs of the associated synclines. An appreciable amount of barite suitable for commercial use has been indicated by trenching and core drilling. The Gap Mountain and Fancy Hill deposits are controlled by the Magnet Cove Barium Corp. and Baroid Sales Division of National Load Co., respectively. The ore is similar to that of the Magnet Cove area and is amenable to concentration by a flotation process. Mining of these deposits had not been begun by the time the Bureau completed its exploration project."

Nov 1, 1946