Search Documents

By P. D. Kovscek

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted mechanical cutting system to determine the effect of the high-pressure sprays on machine performance, airborne dust levels generated, and size of particles formed. Testing was conducted on a simu-lated coal block (coalcrete) while cutting at a water pressure of 190 psi and at water-jet-assisted pressures ranging from 1,000 to 6,000 psi. The shearer motor energy used by the shearer while cutting coalcrete was determined for each cutting condition. Results indicate that the motor energy required by the shearer for each ton of material cut did not vary significantly as the water pressure was increased. Results of dust measurements recorded near the cutting drum indicate that at water pressures above 3,000 psi, dust reductions up to 85 pct were achieved com-pared with cutting with conventional sprays. Analysis of the particle size distribution during cutting showed that increasing the water pres-sure resulted in increased median particle size. In light of these results, various mechanisms for water-jet-assisted cutting are discussed.

Jan 1, 1986

By M. J. Beus

Researchers at the U.S. Bureau of Mines have developed personal-computer-based data acquisition, instrumentation, and mine visualization and modeling techniques to evaluate a mine accessway in a deep hard-rock mine in northern Idaho. These techniques were applied to a mine shaft in a large silver mine that has been in operation for many years. A very deep, rectangular, timber-supported shaft extending to depths exceeding 2.3 km (7,500 ft) had been deforming continuously as a result of nearby mining, resulting in operational problems. Preliminary visual observations and rock and support monitoring confirmed that severe diagonal distortion was occurring. Extensive field measurements and data analysis confirmed initial observations, provided insights into the cause of deformation, and defined a general approach to structural modeling. Computer analysis of the problem was initiated by developing a three-dimensional model of the terrain. This represented a volume of rock approximately 80 km3 (40 x 1010 ft3) and an area on the surface surrounding the mine 9 km2 (3 square miles). Based on this model, a three-dimensional, finite- element analysis was conducted to establish boundary conditions for sequentially more detailed two- and three-dimensional submodels of the shaft area. Results from the computer study are being used to develop new approaches to mine design and to provide design guidelines for deep mine accessways subject to severe rock-mass loading conditions.

Jan 1, 2010

By G. R. Strimbeck

Experimental work is report on the gasification of 90-percent through 200-mesh, strongly coking Sewickley-bed coal with oxygen and with steam in three temperature ranges, namely, 2,700° to 3,400° F., 1,600° to 2,000° F., and 230° to 250° F. Thirty-one runs have been made, during which 56,000 pounds of coal have been charged to the generator at feed rates of 200 to 450 pounds of coal per hour. The average results, not the optimum results, are given in the following tabulation:

Jan 1, 1950

By O. H. Metzger

This is one of a series of capers being published by the Bureau of Mines on gold mining A the Western States. It describes the production of gold in the principal mining districts of New Mexico. The material was gathered red on a trip through tale State in the summer of 1936. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of mine operators in all parts of the State, who willingly contributed all information requested. Geological reports of the Geological Survey and the New. Mexico Bureau of Mince were drawn upon freely for information; credit to individual paper, is given in the text.

Jan 1, 1938

By R. W. Van Dolah

An attempt has been made in this investigation to define the conditions under which ammonium nitrate (AN) might detonate as a result of involvement in fire. The initiation of detonation by shocks derived from explosives or from projectile impact was investigated as a function of temperature and charge diameter. A new technique was devised to investigate the burning of raw and contaminated AN under pressure. No transition, to detonation in AN was obtained in the burning experiments. The critical diameter for detonation of fertilizer-grade AN was found to be quite small when the AN was at temperatures just below melting point; this indicates that initiation of detonation may be less difficult at elevated temperatures but such initiation by gas-phase detonation was shown to be unlikely. Transition from burning to detonation was obtained with AN intimately mixed with fuels that included polyethyl-ene, paper, and fuel oil when these were contained in vessels with restricted vents. However, the experimental results supported by an analytical study indicate that the initiation of detonation in AN from fire exposure in normal storage and from transportation incidents is quite improbable. The detonation of AN in recent incidents more likely may have resulted from the effects of adjacent explosions.

Jan 1, 1966

By R. A. Isberg, D. A. Parrish, H. Kramer

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75% coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 3, 1981

By John H. Weitz

Dolomite, heretofore regarded merely as a variety of commonplace limestone, has suddenly attained headline prominence, partly because of the increase in demand for dolomite refractories to line metallurgical furnaces now working at an unprecedented rate of activity, but chiefly because it has become an ore of the light-weight metal, magnesium, needed in vast quantities for the manufacture of war machines. A multitude of inquiries, chiefly from war agencies and prespective operators, for data not only on locations of dolomite deposits but on their size and quality, has made it necessary for the Bureau of Mines to assemble all information available on this important subject. From the Bureau's own records, published information, and correspondence, date on locutions, extent, thickness, accessibility, workability, and chemical composition of high-grade dolomite deposits throughout the United states were accumulated for presentation herein. The report includes about 1,000 tabulations of analyses and a map showing locations of the deposits. The uses of dolomite are discussed in Bureau of Mines Information Circular 7192, "Occurrences and Uses of Dolomite in the United-States," published in 1941. The cordial corporation of many State ecological surveys and various individuals who have contributed information is gratefully acknowledged.

Jan 1, 1942

By Thomas G. Murdock

ALTHOUGH the contribution of Algeria, including the Sahara, to the local economy and to world mineral supply was small for many years, the spectacular development of an important petroleum and natural-gas industry has changed the position of the country. In 1963 there were decreases in output of most mineral commodities, however oil and gas production forged ahead and established new records. The impact of adverse market conditions and especially the competition from lower cost producing areas was felt by both the metals and nonmetals industries. This and the general economic conditions related to the recovery of the country following the years of strife attending its emergence as an independent state combined to hold back production and development commensurate with resources. The principal events of the year were in the petroleum sector and included the first commercial production from several new fields, some new discoveries, the virtual completion of the first petroleum refinery in the country, and installation of additional pipelines. Progress was made toward the further utilization of the vast resources of natural gas and the provision of additional transportation and refining facilities. In the mining domain the government took over two iron-mining operations, and progress was made towards expanding production of phosphate rock and determining methods of upgrading the Tindouf Iron ores. Completion of the iron and steel plant near Bone was further delayed. The only coal mine reportedly closed down in late 1963.

Jan 1, 1964

By M. J. Beus

The Bureau of Mines, under a cooperative agreement with Hecla Mining Co., is conducting a rock mechanics study of the 6,200-ft-deep circu-lar, concrete-lined Silver Shaft in northern Idaho. The objective of the project was to instrument and evaluate lining behavior and rock de-formation when a deep shaft is constructed in a high in situ stress field and anisotropic rock mass. Rock mass displacements were moni-tored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. Field data from the 5,955-ft test level show that rock displacement is controlled by rock mass anisotropy. Liner stress and strain levels reflect the high in situ stress field as well as nearby station and raise construction. Maximum stresses measured in the lining, as a result of shaft excavation, are about one-third of its compressive strength. Subsequent loading pocket excavation resulted in signifi-cantly increased stress and strain levels in the liner. Continued monitoring and preliminary analysis of the data indicate that concrete-lined, circular shafts are stable for the high, unequal horizontal stress fields and rock anisotropy encountered in deep-level mining. Adjacent development work can be expected to significantly alter the initial stress and displacement conditions.

Jan 1, 1984

By Laxman S. Sundae

The Bureau of Mines designed, fabricated, and is using an in-seam tester (1ST) for in situ determination of coal cutting forces. This re-port describes the results of field tests conducted in the Pocahontas No. 3 and Upper Freeport seams to obtain peak and mean cutting forces during coal cutting with several bit geometries, including radial and point attack bits currently used on drum-type machines. Comparisons were also made between new and worn bits, and using data obtained from a Bureau-modified chisel bit. The test results show that longwall plough cutting (horizontal cuts) in bony coal bands (shale) requires >3 times the cutting force for the same cuts in a vertical direction. When no bony coal is present, the cutting forces required to make horizontal and vertical cuts are equal. Worn bits require 4 to 5 times more cutting and normal force than new or undamaged bits. Normal force increased drastically for the worn chisel bit. Peak force encountered in making independent cuts was found to be ~3 times higher than that required to make interactive cuts using a spacing-to-depth-of-cut ratio of 2. Both rake and clearance angles were found to have a significant effect on normal and cutting force.

Jan 1, 1986

By L. L. Oden

The Bureau of Mines analyzed vapor-aluminum-diffused stainless steels prior to conducting corrosion measurements in severely sulfidizing environments. These studies were conducted in response to the national need to better control the environmental and economic costs of corrosion. Specimens of a ferritic alloy and austenitic alloys types 316 and 310 were treated by a proprietary vapor-aluminum diffusion process and a dual vapor-aluminum diffusion process. Weights and dimensions were recorded before and after treatment, and comprehensive metallographic, X-ray, and electron micro-probe analyses were conducted for both single-and dual-vapor-aluminum-diffused specimens. Surface aluminum concentrations ranged from 26 to 34 wt-pct for all alloys. Dual treatment increased the quantity of aluminum per unit area by a factor of 2 and increased the depth of penetration by a factor of 3. The aluminum-diffused region of the ferritic alloy was single-phase aFe solid solution that was ordered on the surface, whereas two distinct diffusion layers were ob-served on the austenitic alloys. The outer layer comprised aFe solid solution that was ordered on the surface, and the inner layer was a two-phase mixture of aFe solid solution and the interrnetallic compound AINi.

Jan 1, 1982

By Homer J. Ballinger

During the fall of 1943 and spring of 1944, the Bureau of Mines investigated nine secondary limonite iron-ore deposits in the Williamsville district of Wayne, Butler, and Ripley counties, Mo., by rotary-bucket and power-auger drilling test pitting, and trenching. Studies on beneficiating the ores were made at Bureau laboratories. Iron ore has been mined in Missouri since 1825, and iron mining reached its greatest development between 1870 and 1890. During this period, production averaged about 250,000 tons annually.

Jan 1, 1948

By Gary E. Sherman

The Bureau of Mines estimated the remaining lode gold endowment of eight mining districts in Alaska using historic production data. A log-arithmic model of cumulative tonnage of ore processed versus cumulative grade was applied to the following districts: Chichagof, Fairbanks, Homer, Hope-Seward, Juneau, Ketchikan, Prince William Sound, and Willow Creek. To assess the remaining endowment, a computerized production data base was compiled from Bureau records. These data were aggregated in 5-yr intervals for each district. Data were sorted in order of declining grade, and log cumulative grade was plotted against log cumulative tonnage. Linear regression was performed on the data for each district. The linear equation for each curve was used to predict remaining endowment at a limiting mining grade. Based on conservative extrapolation of the grade-tonnage curves, a substantial total endowment of 8,415,100 tr oz of gold remains in the eight districts. The districts with the greatest remaining endowment are the Juneau, Chichagof, Fairbanks, and Willow Creek Districts.

Jan 1, 1987

The Bureau of Mines conducted a field study to assess the performance of various chain pillar configurations in terms of gate road entry sta-bility. Vibrating wire stressmeters (VWS's) were installed in four consecutive gate road chain pillars. Field data collected during panel retreat were analyzed to gain a better understanding of the mechanics of vertical load redistribution in gate road chain pillars as it relates to ground control problems. Several different pillar configurations were investigated including abutment-yield and yield-abutment-yield designs. VWS data indicate that average pillar loads were lower and appeared abutment-yield pillar arrangement was utilized. port the occurrence of severe roof and pillar to stabilize when an Data analyses also supdeterioration that was visually observed in the tailgate entries during panel extraction.

Jan 1, 1988

By W. H. Hamilton

The Kokomo (Tenmile) mining district has had an output valued between $20 and $30 million, mostly from production of silver, lead, and zinc, since 1878. For many years before World War II, there was little production, as the complex nature of the ores made them unattractive at existing metal prices. Under the stimulus of the war, the Geological Survey and the Bureau of Mines studied they district, and in October 1944 the Bureau of Mines began an exploration project, which included dia¬mond drilling, bulldozer trenching, and geophysical surveying. Project work was continued until March 1949, except for short recesses during 1945, 1947, and 1948. Forty-five diamond-drill holes, totaling about 13,000 feet, were drilled from underground and surface stations on the various properties in the district. Eleven bulldozer trenches, abut 2,400 linear feet, were excavated in an attempt to uncover the outcrop of the middle Quail limestone. These trenches ranged from 100 to 485 feet in length and reached a maximum depth of 15 feet. A limited geophysical investigation was made during the summer of 1946. The length of the traverses were: Magnetic, 990 feet; resistivity, 6,250 feet; and self-potential, 69,780 feet.

Jan 1, 1955

By E. Morrice

The metallurgical laboratory data developed in this study indicate an improved electrowinning process for producing higher purity cerium ingot. A typical sample of the Reno electrocerium contains 99.9 weight-percent cerium and the following impurities: Total other rare-earth elements, less than 0.04 percent; iron not detected; silicon and aluminum, less than 0.02 percent each; calcium plus magnesium, less than 0.01 percent; carbon, 0.01 percent; oxygen, 0.002 percent; hydrogen, 0.0003 percent; and nitrogen, 0.0015 percent.

Jan 1, 1960

By Frank A. Peters

The Bayer process treating Jamaican bauxite was evaluated from an economic standpoint, using standard estimating methods and published data, to present a reference point for cost estimates for nonbauxite alumina processes. The estimated operating cost for a plant producing 1,000 tons of alumina a day is $47.96 per ton of alumina when charging $8 per ton for bauxite and $2.30 per hour for direct labor. The estimated fixed capital cost is $46 million.

Jan 1, 1966

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By Larry A. Haas

A major problem encountered in dump leaching operations is the plugging of both the dump and the piping by precipitated iron compounds. Bureau of Mines research to obtain basic data on agitation leaching and dump leaching methods has shown that the addition of organic chelating reagents can significantly enhance the lixiviant permeability through the ore and the concentration of the metal values in the liquor. For example, the addition of 5 giL citric acid (CA) to a conventional sulfuric acid lixiviant almost doubled the fluid flow rate through 5-cm-diameter laboratory columns containing copper ore. After 185 h of per-colation leaching, the metal concentrations with (and without, in parentheses) CA were 1.7 (1.5) giL Cu, 200 (70) ppm Mn, 160 (40) ppm AI, and 6 (3) ppm Co. The enhancement of metal concentrations with chelating reagents such as CA was confirmed by determining the solubil-ity of several metal ions as functions of pH and chelating reagent con-centration. When ferric ions became insoluble at pH values above 3, the concentrations of other ions also decreased. The addition of che-lating reagents kept iron, as well as the other dissolved metals, in solution even at pH values as high as 5. Citric acid was a more effective chelating reagent than gluconic acid, oxalic acid, or sodium lignin sulfonate.

Jan 1, 1985

By Philip C. Tully

This bibliography contains 2,072 citations to technical and scientific literature about helium and alpha-particles abstracted by 12 abstract service publications during 1962. Citations are listed by 16 major subject classifications with several subclassifications to minimize areas of literature search. Automatic data processing was used to reduce the time and labor required to compile the bibliography.

Jan 1, 1969