Search Documents

By William C. Cooley

This volume contains copies of the 5 x 8 in. accession card file for all items collected which were judged to be relevant to underground hydraulic coal mining. In many cases, abstracts are included. Abstracts were taken from the source, from other reviews, or from the preliminary screening of Russian documents performed by Dr. A. L. Brichant. No attempt was made to write abstracts for every accession item.

Jan 1, 1975

By P. Nicholls

[This paper sets forth the burning characteristics of coke used as a domestic fuel as shown by work of the U. S. Bureau of Mines and others. Coke is a truly smokeless solid fuel and is held in high regard for this quality. Ways are being found for making commercial coke from a wider range of cools than heretofore, and tale use of coke for domestic heating is increasing. ACKNOWLEDGMENTS The experimental work reported in this paper was conducted at the Pittsburgh Experiment Station of the U. S. Bureau of Mines cinder the authority of O. P. Hood, chief mechanical engineer; M. L. Orr, assistant feels engineer, and W. M. Brewer, junior fuels engineer, assisted by Charles Schramm cooperated in making the tests.]

Jan 1, 1929

By F. L. Wideman

This report describes the sinking of No. 3 shaft at the Westvaco mine. It is one of a series of publications of the Bureau of Mines on mining methods and practices in the United States. The Westvaco mine is in Sweetwater County, Wyo., approximately 23 miles northwest of the town of Green River (fig. I), There are no permanent habitations in the vicinity of the mine, and employees live in Green River or Rock Springs, Wyo., 14 miles us t of Green River. The mine plant is on a windswept, treeless plain, from which low buttes and flat-topped ridges rise. The altitude at the collar of No. 3 shaft is 6,351 feet. The climate is arid, with temperatures as low as 40° below zero in the winter. Blacks Fork, a tributary of the Green River and a perennial stream, flows near the mine.

Jan 1, 1959

By Thomas M. Barczak

The success of longwall mining can largely be traced to the development of powered roof support systems. The most significant improvement in powered support design has been the shield support, which improved kinematic stability and promoted the application of longwall mining in difficult-to- control caving conditions where chock and frame supports were inadequate. The most obvious trend in shield design has been an increase in shield size and capacity. This U.S. Bureau of Mines report examines shield design and operation practices and their consequences for the utilization of high-capacity shield support systems. An optimization goal is to minimize support loading by selecting an active shield setting force that is compatible with strata behavior and shield loading characteristics. Shield stiffness is an important design parameter that is often overlooked. A consequence of increasing shield capacity by incorporating larger diameter leg cylinders is a proportional increase in shield stiffness. Setting forces have also increased in direct proportion to the increase in shield capacity. The increased stiffness and higher setting force cause the available capacity to be consumed more quickly, severely limiting the ability of high-capacity supports to last longer and provide reserve capacity for difficult mining conditions.

Jan 1, 1992

By S. J. Gasior

Pilot plant studies showed the technical feasibility of fluidized-bed operation for producing hydrogen and synthesis gas by the steam-iron process. A mixture of iron and iron oxide from 20-to 100-mesh was partially reduced with a simulated producer gas and then oxidized with steam and/or carbon dioxide. Results of tests show the effects of pressure, temperature, bed height, gas-to-solids ratio, type of iron oxide, and composition of gas on the gas and solids conversions during reduction and oxidation. A baffled free-fall solids system was also found operable. The short residence time of about 5 seconds limited conversion of the solids.

Jan 1, 1961

By Raymond W. Hiteshue, Sam Friedman, Paul Dobransky, Robert Madden

A hvab coal was carbonized in a closed system at 600 ° C and 40 to 1 , 200 psig to produce a high- Btu gas and char . By retaining the volatiles within the system, it was possible to virtually eliminate production of tars and oils . Depending on pressure and residence time , yields of combustible gases (72 to 92 percent methane ) amounted to 4,000 to 6,000 cubic feet per ton of maf coal and gross heating values of these gases varied from 830 to 960 Btu per cubic foot . Yields of char (maf ) were about 1,600 pounds per ton of maf coal . Increased residence time favored production of gases but reduced their heating values , whereas increase in pressure resulted in somewhat higher heating values and lower production . Similar effects were observed from the carbonization of a low- temperature tar . If these results could be translated to an economical carbonization process for producing high- Btu gas from coal , the demand for coal could be expanded by 40 to 50 million tons per year . Because of large yields of char , a process of this type would obviously have to be integrated with coal - fired power plants . Fortunately , operations could be conducted at essentially atmospheric pressure as product gas under this condition can be obtained in satisfactory yields and with good quality .

Jan 1, 1964

By James L. Eirls

The objective of this project was to improve a driver's field of view for large trucks used in the mining industry. Rearward viewing was enhanced by improving the rear-view mirror designs. Rear vision was accomplished using a closed circuit television system. Views ahead,, to the right, and downward were obtained with a blind area viewer (BAV). The BAV is a unique combination of fresnel lenses housed in a shielded, environmentally protected enclosure that produces an image of the area in front of and downward 70° and to either side of the BAV 300. The improved visibility devices were evaluated by long-term, in-mine testing. The right Bide mirror (RSM) and BAV provide the greatest improvements for the least cost and are commercially available. Application of the RSM and BAV should achieve a reduction in accident potential and greater vehicle productivity by enlarging and improving the equipment operator's visibility and making priviously blind areas and hazardous situations detectable.

Jan 1, 1982

By Manuel Gomez

The Bureau of Mines used data from 31 core samples to develop prediction equations for evaluating chemical and carbonization properties of six seam units in a lignite deposit approximately 2 miles wide and 8 miles long in the Wilcox Formation of central Texas. Statistical response surfaces, based on core analyses, were computed for 14 parameters indicative of lignite quality. These computed surfaces, and their mathematical equations, can be used to predict values of the selected properties of the lignite seams at any desired surface coordinate position between core hole locations. The wide range of application shown by this study indicates that the methods of statistical regression analysis may be useful to evaluate large deposits of lignite or higher rank coal.

Jan 1, 1969

By Launa Mallett, Charles Vaught, Michael Brnich, ROBERT PETERS

Interviews of 48 miners who escaped underground coal mine fires revealed that none of them had ever, before that incident, worn their self-contained self-rescuer (SCSR) either in training or in a real emergency. Consequently, they were ill-prepared to use this emergency breathing apparatus. One persistent problem stemmed from the fact that miners had no notion of breathing resistance, nor of the fact that it would get more difficult to breathe the longer they wore their device. As a result, many of those who were interviewed had simply removed their mouthpieces and breathed ambient air. This is obviously behavior that should be trained out of the workforce. Unfortunately, because of high costs and difficult logistics, miner training is unlikely to ever include donning and wearing an apparatus on a regular basis. In order to give workers a better idea of what to expect from their devices, therefore, the National Institute for Occupational Safety and Health researchers developed a tabletop (paper and pencil) simulation based upon actual predicaments evacuees had reported encountering. The simulation is designed to emphasize important points related to donning and wearing a self-contained self-rescuer in a mine fire escape, and, by doing so, to bring miners' expectations more in line with what their actual experiences would be. The simulation was field tested in six training classes at three different mining operations. In all, 99 individuals were involved in completing the exercise and rating its properties. In their ratings 88% of the respondents indicated they thought the scenario could definitely happen in real life, and over 80% agreed they had learned something new. From the field test data it was concluded that the simulation had authenticity and potential value as a teaching tool. The simulation was therefore used in a pre-test/post-test control group experiment to determine whether it led to improvements in miners' scores on a true-false test of their SCSR's functional capabilities and proper usage. Eighty-three miners were included in this part of the study. As expected, miners who had participated in the training exercise scored significantly higher on their post-test than miners who had not.

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By Rustu S. Kalyoncu

Nonoxide ceramics with improved high-temperature properties could substitute for high-temperature alloys and reduce toe Nation's dependence on imports of Cr, Co, Ni, and Mn. To meet this objective, the Bureau of Mines conducted research to synthesize u1trafine reactive boron nitride (BN) powders BN powders were prepared at temperatures ranging from -75? to 750? C. Low-temperature reactions (-75? to 200? C) between boron halides and N compounds led to formation of e1emento-organic compounds that were thermally decomposed to u1trafine (approximately 100-to 150-A particle size) reactive BN powders. BN powders were also prepared through the reaction of a 10w-me1tinginorganic B compound (boric acid, borax) with an organic N compound (carbimide and thiocarbimide) in N2 and/or ammonia (NH3) atmospheres at temperatures between 500? and 750? C.

Jan 1, 1986

By W. M. Myers

"The continued expansion of modern industry broadens the markets for minerals and their product. With these increasing demands new uses are being found for minerals that heretofore were considered as possessing no commercial possibilities. This tendency is reflected in the nonmetallic field in a constantly increasing demand for minerals formerly considered to be of scientific interest only, Furthermore, nonmetallic minerals of established commercial importance are used in new ways in various products, and this tends to expand the markets for these minerals. Some recent outstanding developments in applications of minerals are given in the following pages.The Andalusite GroupAmong the minerals that until recently were considered of scientific interest only, may be listed those of the andalusite group. This group is composed of the three minerals, andalusite, cyanite (or kyunite), and sillmanite, which are all forms of the compound Al2SiO5 (A1203, S1O2), and are therefore identical in chemical composition, but differ in physical properties,"

Mar 1, 1924

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By David Burgess

Natural gas is a general term applied to the gas obtained from oil or gas wells. It is the most widely used of all gaseous fuels. The principal disadvantage in the use of this and other gaseous fuels is the difficulty encountered in the storage and transportation of large quantities in the gas state. Handling in the liquid state is possible, but reduced temperatures are required since methane (table 1) is the principal component of most natural gases that are used as fuels. Actually, liquid storage has been utilized both here and abroad;3 however, the Cleveland disaster4 has pointed out the need for a critical evaluation of the hazards involved in the storage of this cryogenic fuel. Accordingly, a program was undertaken to obtain basic data that could be used to assess these hazards. In this report, the factors to be considered in an evaluation of the fire and explosion hazards associated with any fuel are each discussed briefly. These factors are then used to assist in the design of experiments for the evaluation of the hazards associated with liquefied natural gas (LNG) relative to those associated with other common fuels. Experiments have been conducted on the vaporization of LNG, the mixing of LNG vapors with air, the effect of temperature and nitrogen dilution on the limits of flammability of methane in air, the burning rates of LNG and other fuels, flame radiation, and extinguishment of fires above liquid pools. Based on the results of these experiments, LNG can be stored safely in suitably designed above-ground tanks surrounded by earthen dikes in much the same manner as gasoline.

Jan 1, 1962

By David W. Houseknecht

Probabilities of encountering coalbed discontinuities during vertical or horizontal drilling in a specific coalbed can be estimated based on analysis of mined-out areas of the coalbed where the size, shape, orientation, and distribution of discontinuities are known. The result- ant probability estimates can be applied to cost-risk evaluations of drilling programs proposed for exploratory, developmental, or methane drainage purposes in undeveloped areas of that coalbed. Data compiled from mine maps of the Beckley Coalbed in southern West Virginia were used to estimate the probabilities that discontinuities would be encountered in two illustrative hypothetical drilling programs--one for drilling vertical boreholes and the other for drilling horizontal boreholes. Analysis based on a mined-out area of the Beckley Coalbed indicated that vertical methane drainage boreholes spaced 1,000 feet apart in a square grid pattern would each have a 29 percent probability of encountering a discontinuity in a geologically unexplored area of the coalbed. It was also determined that exploratory vertical drilling could locate most of the discontinuities if a borehole spacing of 2,500 feet were used. For horizontal drainage boreholes in the Beck- ley Coalbed, the analysis indicated a linear relationship between hole length and the probability of encountering a discontinuity.

Jan 1, 1982

By Paul S. Schopf

The results of an experimental investigation into the possible use of medium energy acoustic fields (130 to 140 dB) to precipitate 1 to 10 micron particles is presented. The aerosol was produced with a LeMer generator using oleic acid and nitrogen. The sound field was a sinusoidal standing wave field in an acrylic tube, with light transmission data used for concentration determination. The results showed collection efficiencies of up to 80% on 2 micron particles with a residence time of 11.8 seconds at a sound pressure level of 139 dB re 2x10-5 N/m2. A discussion of the possible turbulent mechanism is made, as well as review and comparison with others? work.

Jan 1, 1972

By A. B. Hooker, L. C. IlsLey

"The last previous Bureau of Mines publication relative to details of permissible electric mine lamps is Bulletin 332, which describes 16 lamps approved prior to May 1930. Some of the lamps have become obsolete through the development of improved models which, with several new types, make it desirable to supplement the Bureau's published data relative to permissible electric mine lamps.In the following descriptions, lamps approved since May 1930 and prior to July 1, 1935, are placed in the three following groups: (1) Electric cap lamps, (2) electric hand lamps, and (3) lamps for miscellaneous applications,ELECTRIC CAP LAMPS APPROVED UNDER SCHEDULE 6B1. Edison model J lamp, approval no. 24. - The features that distinguish this lamp from earlier models of Edison electric cap lamps are:(a) The battery consists of two F-2 cells of square cross section and about 1-1/4 inches higher than M-14 cells in the model H lamp, making the battery narrower and higher than any of the earlier models of Edison cap lamps.(b) The cells are insulated from each other and the Monel-metal casing by enclosure in vulcanized-rubber baglike enclosures. Both cell terminals are insulated from the cell jar.(c) The battery is equipped with rubber-tube Bunsen-valve-type gas vents.(d) The battery casing is secured by a new-type magnetic lock.(e.) The battery and cover terminal clips have been redesigned to give a wiping contact."

Jun 1, 1936

By Eugene T. Sheridan

The United States has extensive reserves of peat. Peat and muck lands are estimated at approximately 79 million acres, with reserves of 13.8 billion net tons. Within the past decade domestic production of peat has increased 2-1/2 times, and apparent consumption has tripled. During the same period imports have increased greatly, and in 1955 they almost equaled domestic production. The substantial increase in the demand for peat in the United States was due chiefly to expanding markets in agriculture and horticulture, for the reason that in this country peat is used primarily as a source of organic matter to improve the physical condition of mineral soils and as a mulch for shrubbery. A valuable constituent of any soil is its organic matter, and its depletion will injure cultivated soils and subject them to greater erosion.

Jan 1, 1957

By Allan J. Clark

This paper, describing the milling practice of the Homestake Mining Co., is one of a series being prepared by the Bureau of Mines. The author acknowledges the assistance of T. G. Chapman, one of the consulting engineers of the Bureau of Mines, in arranging this paper for publication.

Jan 1, 1931

By Paul Biggs

This report presents information on 77 waterflood projects in 31 Montana oilfields. The study shows the locations of the projects, the sources and amounts of injection water, and the results in oil produced. Waterflooding, a secondary recovery technique, began in Montana about 40 years after the initial oil discovery in 1920. Often, the difference between water disposal by injection and pressure maintenance operations is not clear. Water injected at the projects in 1973 was 157.7 million barrels. In 1973, the 31 fields having waterflood projects produced 28.3 million barrels of oil valued at $88.4 million. Both in volume and value, this represents over 80 percent of the State's 1973 oil output. The projects are making possible the recovery of additional oil, thus contributing to the conservation of oil and lessening the impact of the current oil shortage.

Jan 1, 1976