Search Documents

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

By J. J. Sammarco

Light emitting diodes (LEDs) are emerging as viable replacements for incandescent-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. The present paper describes the performance of LED and incandescent sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and airflow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Secondly, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and incandescent sources can be magnified toward the end of a 10­hour battery discharge cycle. Empirically, we have determined that after 8 hours at an ambient temperature of 25 °C, the average light output of an incandescent cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and airflow on the light output of an LED and incandescent cap lamp were conducted in the NIOSH Safety Research Coal Mine (SRCM). The LED cap lamp yielded a vertical average illuminance improvement of approximately 9.5% and the INC cap lamp yielded a vertical average illuminance degradation o f approximately 4%. The differences between LED and incandescent cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38 % more efficient than the incandescent cap lamp with a lead-acid battery at the end of the 10-hour driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the incandescent light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, especially given that the light output will decrease an additional 30% to 45% over the period of a 10-hour shift. The implications of the differences between LED and incandescent sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and incandescent cap lamp visual performance research.

Jan 1, 2008

By Bertrand L. Johnson

As potash is more necessary to the agricultural economy of the United States now than ever before it is gratifying to find that the virtual stoppage of imports from Germany in late 1939 caused none of the anxious foreboding that gripped American farmers in 1914. For long decades this country, in common with tie rest of the world, depended upon German potash, but today our expanded needs can be mot from domestic sources. The present armed conflict in Europe, like that of 1914, disrupted a world monopoly, but the cartel that in recent years controlled 90 percent of the world output (see fig, 1) was an international syndicate comprising French, Polish, and Spanish as well as German producers and having reported sales agreements covering production in the U. S. S. R. and Palestine. The break-up of these commercial agreements has necessitated readjustments but generates no such alarm as the closing of a single source of supply. In striking contrast to the critical shortage that developed a quarter century ago, no increase in prices has occurred or is anticipated in the domestic market.

Jan 1, 1940

By Beverly W. Dunning

The effect of vacuum melting on the elimination of gases and nonmetallic inclusions for six low-alloy steels was investigated. The purpose of these studies was the analysis and comparison of differences in gas content and inclusions in air-melted and vacuum-melted steel. Data obtained from melts of 1-1/4 to 20 pounds indicate that vacuum melting decreases the number and size of nonmetallic inclusions and at the same time increases the degree of dispersion of the remaining inclusions. These improvements are undoubtedly related to the elimination of approximately 80 percent of the nitrogen and 90 percent of the oxygen as well as most of the undesirable metallic trace impurities.

Jan 1, 1961

By P. A. Wasson

The investigation described in this publication was conducted by the Bureau of Mines to determine the effectiveness of the anionic silica flotation method on goethitic iron-bearing materials from the Cuyuna Range, Minn. Samples used in this investigation were a composite of drill core from 13 holes, and 3 samples from lean ore stockpiles. These samples are believed to be typical of the mineralization occurring in an area with a potential reserve of several million tans of submarginal iron ore. Results from batch tests showed that the iron-bearing minerals could be effectively concentrated by flotation removal of the siliceous gangue. The drill hole composite yielded laboratory flotation concentrates from locked tests containing 56.8 percent Fe and 6.1 percent silica, with an accompanying iron unit recovery of 94.2 percent. Concentrates containing 52.4 to 53.7 percent Fe also were produced from the lean ore stockpile materials; corresponging iron recoveries ranged from 71 to 79 percent in the batch tests, with the possibility remaining for additional recovery of iron from the middlings.

Jan 1, 1963

By D. H. Carlson, J. H. Johnson

"The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios.The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. Concentrations of CO and C02 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for C02• EMA measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and C02 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios."

Mar 1, 1992

By J. P. Bennett

The Bureau of Mines investigated the dimensional changes of ceramic materials exposed to acid environments to evaluate construction materials for emerging technology in chemical and metallurgical processes. Six commercial ceramic materials (two red shale, two fireclay, one silica, and one silicon carbide (SiC» were exposed to H20, 20 and 30 wt pct HCl, 40 and 60 wt pct HN03, and 10 and 50 wt pct H2S04 at temperatures from 50° to 90° C for 300 days. Linear expansions ranged from a low of -0.02 pct for the silica to a high of 0.45 pct for the red shale. A general ranking of the volume expansion of the materials tested, (from high to low), is as follows: high-porosity red shale A and fireclay B » low-porosity red shale B and fireclay A > silicon carbide and silica. A general ranking (largest to smallest) of the effect of exposure environments is HCl > H2S04, HN03 > H20. An autoclave test method was evaluated. Data obtained from 8-to 24-h exposures were compared with data obtained from the 300-day exposures. The relative expansion trends were similar, indicating that this method could be used as an accelerated test.

Jan 1, 1988

By David C. Oyler

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbed at a vertical depth of 999 feet. The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a "bird foot" pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to 130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By A. C. Rice

Investigation of a variety of mines to determine efficiency for rare- earth extraction has resulted in a solvent extraction technique wherein Primene 81-R,4 N-benzylheptadeeylamine (BHDA), and Primene JM-T give favorable extraction from sulfate solutions. Extraction from chloride, nitrate, and perchlorate solutions is negligible. Distribution coefficients for 10 rare-earth elements with Primene 81-R establish an extraction sequence beginning with lanthanum and proceeding through lutetium according to atomic number. Yttrium and ytterbium are exceptions in the extract ion sequence.

Jan 1, 1962

By Steven J. Page

Accurate measurement of workplace respirable dust concentration is an essential step in eliminating lung disease in any occupational setting. In the United States (U.S.) coal mining industry, this measurement process has relied upon a personal sampler that includes a 10 mm Dorr-Oliver (DO) nylon cyclone operated at a flow rate of 2.0 L min-1 to collect a respirable dust sample. Dust concentrations measured with this sampler are multiplied by 1.38, which was empirically derived, to convert them to measurements approximating the United Kingdom British Medical Research Council (BMRC) definition of respirable dust upon which the health effects of coal mine dust are based. The International Organization for Standardization (ISO) subsequently refined the respirable dust definition and the U.S. National Institute for Occupational Safety and Health (NIOSH) 1995 Criteria for a Recommended Standard presented a conversion multiplier of 0.857 to apply to the 2.0 L min-' DO (in addition to thel.38 multiplier) to obtain equivalent ISO concentrations, as approximated by the 1.7 L min-1 DO. However, the conversion multiplier 0.857 was derived indirectly from a limited size distribution data set rather than a direct comparison of the DO samplers. The present analysis focuses on providing a more accurate conversion multiplier derived from direct comparisons of the 2.0 L min-1 (with 1.38 BMRC equivalency multiplier) and 1.7 L min-1 DO cyclones. A weighted linear regression analysis of this database suggests that a more accurate estimate of the conversion multiplier is 0.815.

Jan 1, 2009

By Mark R. Pettitt

The results of an extensive research and development program to reduce the noise generated during coal cutting are presented. The characteristics and magnitude of continuous miner coal cutting noise sources are defined. This work consisted of development of a simulated coal ,cam to facilitate above-ground coal cutting tests, noise measurements in a reverberant acoustic chamber during simulated mining operations of a continuous miner (cutting the simulated coal scam), and noise measurements in an underground coal mine during continuous miner operation. In-mine and laboratory test results were in excellent agreement for both A-weighted overall levels as well as A-weighted one-third octave band spectra. Methods to reduce coal cutting noise are presented. These methods take full advantage of the dynamic characteristics of the forces generated during coal cutting. Dynamic cutting force isolation was shown to be a very effective technique. Finally, a continuous miner was equipped with a cutter head that incorporated (among other design factors) cutting force isolation. Successful, lung term, in-mine use of the cutter head demonstrated coal cutting noise at the operator's station of less than 90 dBA and 50% coal, 50% rock cutting of less than 93 dBA.

Jan 1, 1985

By C. W. Schultz

The vapor pressure of manganese in equilibrium with a series of liquid iron-manganese alloys was determined by the carrier gas method over a broad range of alloy composition. From these data the activities of manganese in the iron-manganese system were calculated. The system appears to be ideal.

Jan 1, 1966

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By R. C. Hickman

"INTRODUCTION The largest known deposits of ilmenite and rutile in Virginia are in Amherst and Nelson Counties. Other deposits occur in the State, but their extent is not known. One of the most promising of the latter is the deposit in Roanoke County on the T. M. Bush and the H. L. Hutchins property near Roanoke. A geophysical survey was made of the deposit, followed by core drilling. In April and May 1946, four holes were drilled, totaling 822 linear feet.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch,. Bureau of Mines."

Aug 1, 1947

By Walter W. Fowkes

Leonardite is a coallike substance, similar in structure and composition to lignitic coal and believed to be derived from lignitic coal by the process of natural oxidation. Leonardite is little known outside lignite-producing areas and has been developed commercially only to a minor extent. The higher oxygen content and less compact structure of leonardite, compared with lignite, make it undesirable as a fuel but indicate that it has potential as a source of chemicals and for other nonfuel uses. It is a convenient source of humic acids. The United States has a large natural reserve of leonardite; furthermore, it can be produced in the laboratory under controlled conditions. The significant elemental difference between leonardite and lignite is the oxygen content (leonardite, 28-29 percent; lignite, 19-20 percent). The higher oxygen content of leonardite is due entirely to a Larger number of carboxylic acid groups. This fact explains the 17-Cold increase in alkali solubility of leonardite. Spectral studies indicate that the material is mixed salts of humic acids.

Jan 1, 1960

By G. S. Scott, L. D. Schmidt, J. A. KELLEY, E. L. FISH

One of the war problems with which the Bureau of Mines is concerned is to increase production of iron and steel , in which coke is one of the major factors . The output of byproduct coke for use in iron blast furnaces is insufficient and is being supplemented by coke from beehive ovens (figs . 1 , 2 , and 3) . Some difficulties that cause a reduction in iron output have been reported in the use of some of the beehive coke.6/ About 20 years have elapsed since beehive coke was made on a large scale , and many of the skilled operators of those days are no longer available . Furthermore , in many instances the quality of the coal supplied to the ovens has not been as good as formerly. The ash and sulfur contents are often abnormally high; and in other instances they vary greatly in amount, so that a nonuniform coke is produced . To assist operators to improve quality and yield of beehive coke , the Bureau of Mines equipped a truck as a field laboratory ( fig . 4 ) and sent the authors with it into the Pennsylvania beehive district . The truck contains necessary equipment for sampling and analyzing coke oven gases , measuring temperatures , screen - sizing coal, and float -and - sink testing coal . Coal specimens may be sent to the Pittsburgh laboratory for analysis . Beehive plants producing good coke were visited first to observe details of operation and to collect data on the operating process . These covered temperatures , analyses of the exit ( or trunnel) gases , and coal quality, and were to be utilized in searching for faults in plants not producing good - quality coke and to assist in improving such plants or their operation .

Dec 1, 1943

By William H. King

The Mercur Dome mine is in the Camp Floyd mining district, Tooele County, Utah (fig. 1). The property lies between 6,000 and 8,000 feet altitude on the southwesterly slope of the Oquirrh Mountains, a short distance west of Mercur, the district settlement. Mining began in the Mercur area in 1870. Operations at the Mercur Dame mine were started in 1937 after several claims had been consolidated into one group. Preliminary examination of the ground by F. H. Gunnell, a Bureau of Mines engineer, disclosed the presence of vanadium in a carbonaceous shale horizon. Rocks near the Mercur Lame property are chiefly sediments of Carboniferous age, including the Madison and Deseret limestones. The main shaft penetrates the Deseret formation to a point a few feet above the 1,000-foot level where it enters the Madison limestone. The flat-lying vanadiferous shale horizon is exposed on the 1,000-foot level near the top of the Madison limestone. The Bureau of Mines development program, consisting of diamond drilling, auger hole drilling, and sampling, was planned to determine the extent and assay value of the vanadiferous bed. Seven diamond-drill holes totaling 300 feet were drilled from the 1,000-foot level of the mine. Eight hand auger holes were drilled in the back of the drift on this level (fig. 2). Assay determinations were made on 74 samples from the drill holes and supplemental channel samples and are tabulated in this report. The concluding section embodies results of metallurgical tests.

Jan 1, 1949

By E. P. Youngman

The mining law of Chosen, which was made effective April 1, 1916, was promulgated as ordinance 8, December 24, 1915, in accordance with the provisions of articles 1 and 2 of law No. 30 of 1911. The new le repealed the mining law, Fo. 3 of 1906, and the placer mining law, No. of 1906, and in effect annulled all prior mining legislation. An amendment to the mining law of 1916 (by virtue of law No. 30 of 1911) vas. passed December 16, 1918, as ordinence o. 17. The detailed regulations, which were to supplement the law proper, and rich in all probability follow closely the regulations in force in the Empire, were not available. Unless otherwise indicated, references in this paper are to the mining law of 1916.

Mar 1, 1933

By W. L. Falke

Research was conducted to develop methods on a laboratory scale for recovering manganese from manganiferous slimes and limestones . The procedure is a low- temperature modification of the carbamate process , in which manganese is dissolved and the valence reduced by treating slimes and limestones with controlled amounts of sulfurous acid . Manganese ( II) hydroxide is precipitated and leached with ammonium carbamate solution , and manganese carbonate is separated by warming the leach solution . A major portion of the reagents is regenerated and recirculated . About 75 percent of the total manganese in manganiferous slimes , and from 50 to 75 percent of the total manganese in manganiferous limestones , are recovered as manganese carbonate containing 45 percent manganese .

Jan 1, 1964

By Robert W. Metcalf

Since the spread of the European war virtually cut off imports from Denmark, Belgium, and France, the Bureau of Mines has had numerous inquiries as to domestic sources of grinding pebbles and silex or other types of ball mill liners. USES Flint pebbles and tube-rill liners are used by grinders of certain ceramic materials to prevent contamination of the finished product by iron abraded from steal baler and liners. The feldspar industry is one of the largest users of flint grinding mediums; they are employed also by curtain grinders of talc and soapstone, ground sand and sandstone, quartz, and chalk. Some paint materials, such as lithopone, have been ground in pebble Flint pebbles have been used more or less in the past, especially by cement manufacturers, and, for fine grinding of gold, copper, or other ores in which iron contamination is not especially deleterious.

Jan 1, 1940