Search Documents

By X. B. Starnes

"INTRODUCTION The Eva Tanguay property is in Crittenden County, Kentucky, about 1 mile south or the village of Mexico, and can be reached from Marion, the County seat, by travellng south on State Highway 91 for 6.8 miles and then turning southwest on State Highway 70 and traveling 2 miles farther.Although the property lies between the Huffaw and Pigmy properties, which together have produced 200,000 tons of fluorspar ore, production from the Eva Tanguay has been estimed at only 1,000 tons. Geological factors on the property indicated the likelihood of an ore occurrence, and the author examined the property in April 1944. Shortly thereafter, the U.S. Geological Survey wrote a report on the property, which was not published. A drilling program was initiated by the Bureau of Mines November 1, 1944, and continued until eight holes totaling 3,137.5 feet were drilled.The holes showed that the Tubb fault system on the Eva Tanguay property is composed of three members, all of which contained commercial ore. The line dividing the Haffaw and Tanguay properties crosses the vein outcrops, causing a part of the ore indicated to be on each property.The mineral rights, which are leased by Robert Frazer of Marion, are owned by Mrs. O. S. Denny and W. C. Bohn, both of Marion."

May 1, 1947

By R. D. Leitch

[The accepted theory of acid formation in coal mines with the subsequent appearance of the acid in coal-mine drainage, is oxidation of iron pyrite and subsequent solution and hydrolysis of the iron sulphate formed. It has also been found that 5 gobbed sections and worked-out areas, where there is usually an abundance of iron pyrite-bearing, materials in contact with air, are the sections that make the most important contribution to the quantity of acid drainage. It would thus seem obvious that if oxygen can be kept out of contact with tae acid-forming materials in tie- sections mentioned the amount of acid in coal-mine drainage could be reduced markedly and corrosion problems with mine pumping equipment and general stream pollution mitigated thereby. Although the efficiency of the suggested remedy as been borne out by laboratory experiments6, it has appeared desirable to substantiate the laboratory work by field observations in so far as pertinent data are available. It has been difficult to learn of mines or sections of mines about to be sealed, whereby an actual comparison of the drainage before and after sealing can be made. In view of that difficulty it has been necessary to devote attention to a comparison of the character of the water from areas already sealed with that from open but otherwise comparable sections of the sane mine. Previous cork has shown that the acidity of drainage in different parts of the same mine may vary, but if it can be shown also that the water from sealed areas is with but fen exceptions less acid than the otherwise similar open sections of tae same mine, the laboratory finding will be supported in a practical gray. This report presents some of the evidence that has been obtained.]

Jan 1, 1930

By Charles L. Kimbell

The concept of data availability must be addressed, because there are perceptible changes from year to year, and the availability of accurately reported, precisely defined statistics and nonstatistical information provides the only sound basis for analytical studies required for government policy planning or industry market analysis. As the countries of Eastern Europe and the former U.S.S.R. undergo the transition from centrally planned economies to market economies, there has been a perceptible increase in information availability for rather obvious reasons. Any industrial operation seeking economic assistance from Government and/or private sources outside the country in which the facility is sited must provide some appraisal of its operations at the time it seeks assistance, as well as some information on previous performance to serve as tools in evaluating its potential under the proposed development scheme for which it seeks financial assistance. Additionally, there was growing governmental recognition that concealment of much of the national mineral production, trade, and consumption data for purposes of national military and/or economic security probably never was very successful, never was really necessary for most commodities, and certainly proved unnecessary with the end of the so-called cold war. Indeed, the long-term unwillingness to publish uniform statistical series of reliable,

Jan 1, 1993

By Arthur M. Hartstein

The Bureau of Mines, through contract with Ultrasystems, Inc., obtained data on the oxidative degradative behavior of a number of materials used in coal mines. Tests were performed using a stagnation burner arrangement. Materials examined included those used in typical coal mining operations such as (1) polyvinyl chloride-containing materials. (2) neoprene compositions, (3) rigid foams (urethanes/isocyanates), (4) miscellaneous materials (including jute, fiber glass, and polyethylene), (5) coal, (6) fluids (phosphate esters, organic esters, oil-water emulsions), and (7) composites. The composite comprised a mixture of a phosphate ester fluid with (1) coal, (2) a representative polyvinyl chloride sample, or (3) a neoprene-type composition. A number of decomposition products are identified that could represent a potential health hazard to miners including HC1, CO, SO2 and H2S, if they were generated to exceed toxic levels.

Jan 1, 1974

By P. D. Bergman

To assess the efficacy and economics of producing power from coal, four open-cycle magnetohydrodynamic (MHD) processing schemes were selected for study. Each involved a different mode of coal combustion and level of gas cleanliness. The options considered were: (1) coal burned in a slagging combustor; (2) suspension gasification with slag removal prior to combustion; (3) parallel cyclone combustors, one operating fuel rich and the other operating with excess air; and (4) suspension gasification by the hot exhaust gases from the MHO duct with ash removed prior to combustion. Option 1 has the highest ash content in the combustion plasma and as a result would have the greatest operational difficulties associated with it. Options 2 and 4 have the cleanest MHD combustion plasma. For coal priced at $4/ton, the power generating cost of option 4,11.78 mills/Kw-hr, is the highest, with Option 1, at 9.04 mills/kW-hr the lowest. These costs may be compared with a conventional power cost of 9.92 mills/kW-hr for the late seventies. Capital costs of three of the four options were competitive with those of conventional thermal power plants employing stack gas S02 cleanup systems. Option 2 has the most favorable combination of operating characteristics and power cost. It was concluded that a clean, high-temperature working fluid can probably be produced from coal without leading to depressed system efficiencies and exorbitant capital costs.

Jan 1, 1973

By William W. Elmer

This paper, describing the mining method at the Black Butte quicksilver mine, is one of a series of papers being prepared by the U. S. Bureau of Mines on mining practices, methods, and costs in the various districts of the United States. It is presented to show the mining practice and costs in the successful treatment of low-grade quicksilver deposits. The operation discussed is an excellent example of w1-pat can be done in working a limited tonnage of low-grade ore under sound management. The Black Butte mine is situated at Black Butte, Lane County, in the southern part of the State of Oregon, 17-1/2 miles from Cottage Grove -- a station on the Siskiyou branch of the Southern Pacific Co. The Black Butte mining district lies in the foothills of the Calapooia Mountain Range, which connects with the Cascade Range on the east and with the Coast Range on the west. The elevation at '.lie reduction plant is 1,000 feet above sea level. The apex of Black Butte Mountain, or which the mine is situated, has an elevation of 2,700 feet. The district possesses exceptional natural facilities infrequently met with elsewhere for the mining and reduction of cinnabar ores. Several factors which contribute to the unusually low mining costs are:

Jan 1, 1930

By A. M. Cummings

During August 1943, the Bureau of Mines undertook sampling and measuring of the Kennedy zinc tailing pile near Hazel Green, Lafayette County, south-western Wisconsin, as part of a general investigation of this lead-and zinc-producing area at a time when it was extremely important to increase the production of metals for the Nation's War program. The tailing pile was the residue from old jigging plants that treated ore from the Kennedy mine, one of the oldest and. largest mines in the district. Because retreatment of tailing by modern milling methods was proving economically successful at other sites in the southwestern Wisconsin field, the Bureau?s investigation was designed to assist the potential operators in evaluating the feasibility of a retreatment operation at this site. The study involved measurement of the tailing pile and sampling by means of auger to determine the average metal content within the narrowest possible limits. A total of 46 auger holes ranging in depths up to 40 feet and aggregating 886.5 feet of bore were drilled in the tailing pile, and weighted samples from each hole were analyzed and averaged to determine the zinc and iron content of the tailing.

Jan 1, 1949

By Ruth A. Holmes

A Bureau of Mines method for recovering nickel, cobalt, and copper from low-grade domestic laterites is described, which includes the unit operations of solvent extraction and electrowinning. Previous Bureau work indicated that addition of Na2S04 (sodium sulfate) to the nickel electrolyte improved current efficiency in nickel electrowinning. The present study determines the compatibility of Na2S04 with nickel strip-ping in the solvent extraction operation of the Bureau method. The effect of adding 100 g/l Na2S04 on nickel stripping, phase disengagement, and pH was determined in comparative laboratory-scale tests. In continuous-circuit testing, Na2S04 reduced stripping efficiency to the extent that five, instead of four, strip stages were required for complete stripping of nickel from the loaded solvent. In tests made in a phase-disengagement cell that had a variable settler area, the addition of Na2S04 did not significantly affect phase separation characteristics. The pH of the nickel electrolyte in the temperature range of 20° to 65° C was also unaffected by the addition of Na2S04. An economic evaluation showed that the energy saved by adding Na2S04 to the electrolyte would more than offset the cost of adding another stripping stage.

Jan 1, 1983

By John B. Shutack

In an effort to improve the performance of the explosive-anchored rock bolt, the Bureau of Mines studied the effect of the detonation velocity of the explosive and type of charge (linear or nonlinear) on the fracturing tendency of the anchor tube. Also, different types of tubing were compared to determine the one most suitable for use as an anchor tube. The Bruceton up-and-down method was applied in tests in which steel shooting blocks having boreholes ranging from 1-3/8 to 2-1/8 inches in diameter were used. Of the four types of tubing evaluated, a welded A-178 tubing that was drawn over a mandrel and renormalized gave the most promising results. The A-179 seamless tubing that is normally used with the explosive bolt was the most inferior. Both types, however, gave significantly better anchorage than the conventional shell when tested in both laboratory and underground experiments. Within the range of velocities studied (5,000 to 7,000 m/sec), the type of explosive showed no significant effect on anchor-tube performance. In general; linear explosive charges provided better anchorage than nonlinear charges.

Jan 1, 1968

By Launa G. Mallett, Charles Vaught, Michael J. Brnich

Beginning in 1991, scientists at the Pittsburgh Research Laboratory recorded interviews with individuals who are recognized as experts in mine emergency response. These 30 veterans related stories and observations from events experienced during as many as 47 years of response activities. Overall, the response veterans averaged 29 years of mine emergency response experience and 35 years of mining experience. Interviewees included representatives from mining companies, the United Mine Workers of America, and State and Federal agencies. Most of their comments dealt not so much with technical aspects of particular mine emergency responses, but rather the human side of more general topics, including preparedness, experience, people on-site, mine rescue teams, and decision-making. An analysis of their interviews provides an overview of lessons learned on-site at some of the largest mine disasters since the mid-1940s. This knowledge was gathered so that it could be provided to today's miners and to tomorrow's emergency response personnel. It is expected that the collective wisdom obtained can be used to help train new responders and guide those decisions that will have to be made on the scenes of future events.

Jan 4, 2004

By R. Karl Zipf

MULSIM/NL (multiple seams, nonlinear) is a new U.S. Bureau of Mines boundary-element-method (BEM) program for calculating stresses and displacements (is., convergence) in coal mines or thin, tabular rnetalliferous veins. This manual gives detailed operating instructions for MULSIM/NL and illustrates its use with several practical examples. While this manual concentrates on the practical aspects of actually running and using MULSIM/NL, another companion report titled "MULSIM/NL- Theoretical and Programmer's Manual" provides mathematical and programming details to those engineers and programmers who need to fully understand the FORTRAN program or desire to alter and enhance it. MULSIMINL analyzes one to four parallel seams that have any orientation with respect to the Earth's surface. Three main features distinguish MULSIM/NL from its predecessors: (1) nonlinear material models, (2) multiple mining steps, and (3) comprehensive energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material including (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. The multiple mining step capability enables the user to simulate a changing mine geometry. Finally, MULSIM/NL performs comprehensive energy release rate calculations.

Jan 1, 1992

By Charles L. Kimbell

Following the pattern established in the 1989 edition of this study, the concept of data availability must be addressed, because there are perceptible changes from year to year, and the availability of accurately reported, precisely defined statistics and nonstatistical information provides the only sound basis for analytical studies of any type. As the countries of eastern Europe, including the numerous states that formerly comprised the U.S.S.R., undergo the transition from centrally planned economies' to market economies, there has been a perceptible increase in information availability for rather obvious reasons. Any industrial operation seeing economic assistance from government and/or private sources outside the country in which the facility is sited must provide some appraisal of its operations at the time it seeks assistance, as well as some information on previous performance to serve as tools in evaluating its potential under the proposed development scheme for which it seeks financial assistance. This situation, coupled with governmental recognition that concealment of much of the national mineral production, trade, and consumption data for purposes of national security probably never was really necessary and certainly proved unnecessary with the end of the so-called cold war, has led to the publication of increasing amounts of both statistical and nonstatistical information in the countries undergoing economic transition.

Jan 1, 1993

By C. F. McCarroll

[Laboratory research and, control in the u?odnction an; utilization of petroleum and its product s have eqLmde& greatly during the past decade, rind much of the routine control and experimental equipment noirr requires the con-stant daily use of liquid nercury. In spite of this greater use, very little consideration has becn given to the hazard that might be occasioned by the toxic vapors of mercury unavoicl.a~l.p spilled or otherwise exposed to the atmosphere during the normcl 2rgced1u.e of ln30r~tor;~r operations. A sfmple visual exami~stion gf' sone of the laborztories reveals the prescnce of a considerable quantity of mercury in the craclcs of floors, on work tebles, ad on and mo7md eql~ipmeilt st.ads. Usually this yercurj ie contaminated with oily and dirt BO th~t it remint; in R finely divided state and a srnarl amount presents a relativell- lag? surface for evaporation. Since mercury shows meas~rable vo!-atility st a tempero.turc as lor^ 2s 8.5O F., mercury vapor will bo present in the atnosphere of anjr laboratory wbr.e mercury is exposed. promiscuously]

Jan 1, 1939

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of Al-Ni alloys con¬taining 0.54 to 30.04 atomic percent nickel with the aid of the high-temperature galvanic cell Al(1) // Al+3 (AlCl3 in NaCI.KC1) // Al-Ni alloy (1 or s). Activities of aluminum and nickel (compared with pure liquid metals as the standard state) show pronounced negative deviation from Raoult's law at 1,273 K. The properties [?G, ?Gxs, ?G ideal, ?GA1, AGxs1, ?Gni , and ?GNixs] have been derived from the experimental data and are summarized in tables and illustrations. At 1,127 K, the thermodynamic stability for the invariant three-phase equilibrium consisting of a saturated liquid, A13Ni, and A13Ni2 has been uniquely defined by an activity for aluminum of 0.751. A free energy of formation at 1,127 K of -7,940 cal/g-atom was derived for the compound A13Ni.

Jan 1, 1975

By Verne S. Mutton, William A. Slivensky, Eric S. Weiss, Kenneth L. Cashdollar, Deepak R. Kohli

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, cooperated with Tecrete Industries Pty. Ltd. and BHP Australia Coal in a research program to evaluate the strength characteristics and air leakage of four seal and two stopping designs for use in underground coal mines. A fundamental safety research area for NIOSH is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach to achieve this goal is to develop new and innovative seal designs that provide increased explosion isolation protection for the mining personnel against ignitions that originate from within the gob or. other worked-out areas of the mine Full-scale seals and stoppings were constructed in the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. They were ail--leakage tested, then subjected to a series of explosions with average pressure pulses ranging from 25 to 500 kPa (3.5 to 72 psi). Instrumentation measured seal displacement and acceleration as a function of time, providing data to assist in the development of numerical models 1'01- future seal design. All three seals designed with Meshblock wire forlnwo~-k ant1 a lnonolithic shotcrete core withstood the first explosion test, which generated an avcr-age rnaximu~n pressure of - 140 kPa (-20 psi) while maintaining acceptable air leakage rates. These seals I-anged from 175 to 325 mm thick. They included a 2.7-m-high by 325-mm-thick seal that was tesled 27 hr after completion against this - 140-kPa explosion pressure, a special requirement of the test program. This seal survived explosions with pressure pulses up to 300 kPa (43 psi). The 2.3-m-high by 325-mm-thick Meshblock seal survived three explosion tests with overpressures up to 455 kPa (66 psi) and satisfied the air leakage criteria. A I ,200-mm-thick plug seal was constructed of two Gunmesh formwork walls in-filled with shotcrete and a 3,450-kPa (500-psi) strength Aquablend core. This plug seal survived three explosions with pressure pulses ranging 11-om 150 lo 430 kPa (-22 to 62.5 psi) with no measurable postexplosion air leakage. Two Gunmesh stoppings with thicknesses 01' 40 and 75 inln withstood explosion overpressures of 23 and 115 kPa, respectively. Anchoring all seal and stopping designs into the roof, ribs, and floor with steel "rootbolts" provided very effective boundary constraint that is critical to the performanceofstructures subject to explosion overpressures.

Jan 8, 1999

By Linda L. Chasko, Larry D. Stowinsky, Ronald S. Conti

Mine operators often rely on mine rescue teams to save lives during an underground emergency such as an underground fire, explosion or roof fall. It is extremely important that team members are provided with adequate exploration equipment and that training simulations are conducted in a realistic manner. A series of mine rescue training exercises was developed, conducted and evaluated by the National Institute for Occupational Safety and Health (NIOSH) in cooperation with the Pennsylvania Department of Environmental Protection, Bureau of Deep Mine Safety. The exercises were conducted at NIOSH’s Lake Lynn Laboratory during 1995 to 1998 and resulted in improved technology and training for mine rescue teams. For example, existing technologies were identified to help rescue teams during exploration. These included chemical light sticks to identify team members and mark crosscuts and mine materials, strobe lights for mapping out escape ways, and a helmet mounted thermal imaging system to see through smoke. A hands-free communication system showed potential for enhanced communications between team members and the fresh air base. A new high-visibility team lifeline that allows for flexibility of movement between team members was developed. A positive-pressure inflatable escape device (IED) was used to isolate the “hazardous” environment from fresh air and allow rescue team members to traverse through. An inflatable feed-tube partition that can rapidly block large openings such as underground passageways and simultaneously provide a feed-tube for high-expansion foam generators was also deployed for several simulations. During the simulations, mine rescue team members donned self-contained breathing apparatuses (SCBA) and traversed more than 305-m of mine passageways filled with nontoxic smoke. Visibility ranged from 0.3 to 0.9-m. In one area of the mine, a kerosene heater was used to simulate a fire and reduce the oxygen concentration. In another area, a 1.5 pct methane zone was established. The team members searched for "victims,” mapped the passageways, built temporary stoppings and ventilated the smoke-filled entries. The teams indicated that the simulations were challenging and very informative.

By Michael J. Pazuchanics, Thomas J. Fisher, John J. Sammarco, Jeffrey H. Welsh

This report (An Introduction to Safety) is the first in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment's life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 and other recognized standards. The scope is "surface and underground safety mining systems employing embedded, networked, and non-networked programmable electronics." System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system's safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a "proof of safety" that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. [ ]

Jan 4, 2001

"While control of dust-related diseases, the objective of the Generic Mineral Technology Center for Respirable Dust, is of prime importance from the human standpoint it is also essential to the economic well-being of the mining industry (FIGURE 23). Although significant progress has been made, the problem continues to be a major concern to the mining community. An increasing global demand for coal and other minerals means that production and the number of miners employed is on the rise. Therefore, the importance of this research to the mining industry cannot be overemphasized.The five areas of dust research are 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. Some experimental projects where the research is conducted almost exclusively in the laboratory may still rely on industry for imput. No industrial resources are necessary to the research of the non-experimental projects, for example computer modeling .The remaining research is classified as experimental and these projects do require interaction with industry in varying degrees. Periodic trips to mining sites in Western Pennsylvania, Southern Ohio, and West Virginia are necessary to record measurements or collect samples. Or companies may provide needed samples or equipment to the university for use in the laboratory. On several projects interaction is limited to advice or information supplied to the researcher by industry personnel."

Aug 31, 1989

By H. H. Schrenk

[A colorimetric method5/ for the determination of benzene in amounts as low as 0.001 mg has been developed recently at the U.S. Bureau of Mines Pittsburgh Experiment Station by the authors, with the assistance of chemical personnel fro a the Allegheny County (Pa.) Relief Works Division. The method is based on the direct nitration of either liquid - or gas - phase benzene, followed by neutralization, extraction with butanone, and final treatment with sodium hydroxide which produces a violet color. The color is matched with color standards of known values. Although the method is adaptable to many conditions the primary objective was a procedure that would be suitable for hygienic investigations. The development worth included a study of possible interference by chemicals that be present in those situations in which the method. would be employed. In this study it was found that a specimen of hexane prepared by the Gulf Research Laboratory, Pittsburgh, by fractionation of West Virginia natural gas gave positive result for benzene, whereas a specimen of pentane prepared in the same manner showed only a trace, and specimens of n -heptane and octane (2,2,4 trimethylpentane) supplied by Eastman Kodak Co. save a negative result. According to information obtained from the Eastman Kodak Co. the latter two compounds were highly purified, the n-heptene being prepared from line and the octane synthesized in the laboratory. On nitration of a larger amount of tae natural hexane a visible quantity, of needlelike crystals which resembled those of m-dinitrobenzene was obtained. The hexane from this nitration was recovered by distillation and again nitrated, but no crystals or colorimetric indication of benzene was obtained. This imitated that the specimen of natural hexane contained a substance which at least had the chemical behavior of benzene.]

Jan 1, 1935

By Martin H. Stanczyk, I. L. Feld

Continuous open - circuit attrition grinding of a coarse commercial kaolin to produce paper - coating clay , which must have a particle size analysis of 70 percent or more minus 2 - micron equivalent spherical diameter ( esd ) , was studied by the Bureau . The coarse clay , containing about 11 percent minus 2 -micron esd material , was ground in a 10 - inch- diameter attrition grinder using continuous single- and multiple - stage grinding circuits . The clay feed rates varied from 10 to 480 pounds per hour . In some tests , the influence of varying loads of sand grinding media on particle size reduction was studied . Batch grinding tests also were made for comparative purposes . Multiple- stage grinding gave better results than single - stage treatment when equivalent raw clay feed rates were used . In the best test made , a product containing about 80 percent minus 2 - micron esd material was obtained when grinding 60 pounds of raw clay per hour using a three - stage grinding circuit . Power consumption in the test was about 318 kilowatt -hours per ton of clay treated or 475 kilowatt - hours per ton of minus 2 - micron esd material produced .

Jan 1, 1963