Search Documents

By Carlton E. Brown

This report contains information on the cells or containers used to hold a known small depth (usually 1 mm. or less) of the dust-containing liquid from impinger, 5/6/ filter-paper,7/ and other samples collected from the air while the particles revealed by a microscope (equipped with a 16-mm., 0.25- or 0.50-N. A. objective and ordinarily used with axial light-field illumination) are counted in order to obtain an index of the concentration of dust in the sampled air. Information is given on such subjects as the kinds of cells available, kinds used, actual depths of cells, and construction of simple, inexpensive cells. ACKNOWLEDGMENTS The interest, encouragement, and assistance received from H. H. Schrenk, chief chemist of the Health Division, in the preparation of this report are gratefully acknowledged, as 'is all other assistance received.

Jan 1, 1945

By Mah Alla D.

Previously existing heat-of-formation values for the oxides of vanadium were rudimentary. They were subject to uncertainties of 1 to 5 kilocalories per gram-atom of contained oxygen. This fact has been the only adverse influence on the accuracy of thermodynamic calculations involving these substances, as the requisite entropy and high-temperature heat-content data are known with reasonable accuracy. This report presents new heat-of-formation data for four oxides of vanadium (VO, V203, V02, and V205), obtained by combustion calorimetry. It is believed that the uncertainties have been reduced to 0.1 to 0.3 kilocalorie per gram-atom of contained oxygen. The new heat-of-formation data were combined with existing entropy and high-temperature heat-content values to obtain free energies of formation of the four oxides at temperatures up to 2,000° K.

Jan 1, 1961

By Kenneth G. Broadhead

Four applications of radiotracer techniques in metallurgical research are described: (1) In electrowinning tungsten from scheelite, molybdenum 99 was used to detemine the molybdenum concentration of the fused alkali-phosphate bath and the electrowon tungsten; (2) an attempt to detemine the solubility of tagged ceric oxide in molten CeF3-BaF2-LiF was unsuccessful, but a high rate of cerium ion exchange was observed; (3) iron 59 was added to cerium during casting and used to follow the migration of iron during solid state electrolysis; (4) radiotracers were used in developing special analytical techniques applicable to high-purity rare-earth metals produced by molten salt electrolysis.

Jan 1, 1963

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By J. R. Hauger, P. A. Romans, W. J. Niebuhr

With suitable instrumentation and techniques it is possible to determine the presence of tantalum in columbium to 20 ppm . This paper discusses the selection of X- ray spectrographic instrumentation and describes a technique for accomplishing the low level determination of tantalum . An ion- exchange method of separating tantalum from columbium is also described .

Jan 1, 1964

By B. J. Scheiner

Electrooxidation of cinnabar mercury ores (HgS) was investigated as a means of providing an effective and economical hydrometallurgical technique for extraction of mercury from its ores, particularly those too low in grade to allow economical metal recovery by retorting or furnacing techniques. Oxidation was accomplished by electrolysis of ere slurried with brine. Cinnabar was dissolved by oxidation of the insoluble sulfide to soluble mercuric salts. The mercury ion in a brine solution forms a stable tetrachloro complex. Typical laboratory experiments required I to 7 hours of electrolysis at 35-percent pulp density in a brine solution that contained 4 to 20 weight-percent sodium chloride (NaCl). Power consumption ranged from 10 to 50 kwhr/ton of dry ore. Mercury extraction values between 90 and 99 percent were obtained with all of the ores investigated. Subsequent mercury recovery from leach solutions was readily accomplished by precipitation on zinc. Pilot mill experiments in a 100- to 200-lb/hr extraction plant are in progress to quantify power and reagent requirements, and extraction and recovery data obtained to date closely parallel those obtained in the laboratory.

Jan 1, 1970

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics of positive corona are presented for air in a 2 - in - diam electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig . Results show that current - voltage relationships depend solely on air density . Comparison of data on positive corona with previously published data on negative corona demonstrates a higher sparkover voltage and a wider range of operability for positive corona at temperatures above 375 ° F. The possibility of achieving higher voltages with positive polarity as indicated by these experiments implies several advantages for the use of positive corona in precipitators to allow better removal of suspended material from hot gases . Based on the physics of an ion in an electrical field , a theoretical equation is derived to define current - voltage characteristics of positive corona in terms of air density . Constants for the equation are evaluated from Calculated current - voltage values at different air densities agree reasonably well with experimental data .

Jan 1, 1964

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By R. K. Koch

The Bureau of Mines produced several series of titanium castings in order to investigate the feasibility of producing commercial-grade titanium castings in bentonite-bonded olivine or zircon sand molds. The use of these molds for titanium casting was investigated as a possible alternative to the industrially used rammed graphite process. Parameters investigated were mold mixtures, mulling, gating, venting, drying, and mold washing. The investigators found that castings with superior ductility and fatigue life, compared with rammed graphite castings, could be made by fume-free pro-cesses in molds bonded by western bentonite, using either olivine or zircon sand. Zircon molds were satisfactory for both light-and heavy-sectioned castings. However, olivine molds were suitable only for light-sectioned castings because the mold-metal reaction became excessive during the pouring of heavy-sectioned castings.

Jan 1, 1981

By R. D. Leitch

Beside many other damaging effects of acid mine drainage, corrosion of pipe lines and pumps frequently adds much to mine operating, costs. Not only is it often necessary to install special and relatively costly acid-resistant materials, but even these may require frequent replacements. It is not unusual for ordinary steel pipe to last only a few days in some highly acid waters, while other common materials, though more resistant, frequently cast only a few weeks. In the spring of 1935, local PWA authorities offered to assign a number of persons to various problems under the direction of regular employees of the Bureau of Mines. It was believed that at least some simple tests on as many different kinds of acid-resistant pipes as could readily be obtained might produce interesting; and valuable information for the mining industry. This paper describes the tests and some results that have since been noted.

Jan 1, 1938

By P. R. Bremmer

As part of a program to devise alternative technologies for producing alumina from domestic resources, the Bureau of Mines investigated the leaching of calcined kaolinitic clay to form basic aluminum chloride solutions. Bench-scale experiments were conducted for single-stage batch leaching with AICl3 solution and three-stage countercurrent leaching with substoichiometric HCI. Variable conditions of clay calcination and leaching were studied to determine their effects on aluminum extraction and pregnant liquor composition,

Jan 1, 1984

By Jeffrey M. Listak

The Bureau of Mines has conducted a rock mechanics study to monitor deformation of near-seam strata above a longwall panel in the Pittsburgh Coalbed. The primary goal was to determine the height of caving immediately behind advancing longwall face supports. This study, although site specific, provides information on the caving mechanism associated with longwall extractions so that strata behavior and its interaction with longwall face supports can be better understood. Two holes were drilled, approximately 550 ft apart along the center line of a longwall panel, from the surface to the coalbed approximately 650 ft below. Various downhole geotechnical instruments were used to monitor strata deformation. In addition, surface elevation surveys were conducted to differentiate between surface and subsurface activity. This report discusses the caving characteristics of the strata as the longwall panel approached and passed beneath the boreholes. Physical property data are also presented to demonstrate the relationship between caving behavior and local geology. Data show that immediate caving of strata above the longwall face occurred at a height less than 23.5 ft and that strata behavior above longwall extractions is highly dependent upon lithology, with major disturbances occurring at weak lithologic zones.

Jan 1, 1986

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the New Galena Deposit in an endeavor to find an additional source of supply of lead. In Bucks County, lead and zinc minerals have been found in shales over a largo area west and northwest of Doylestown. Considerable mining has been done in the vicinity of New Galena on the North Branch of Noshaminy Creek, 3 miles northwest of Doylestown. It has not been possible to obtain a satisfactory history of the New Galena mine, as there is much disagreement in statements. Most of the mining was done in open pits. Two shafts were sunk to shallow depth; one of these became part of the main pit' which is 256 foot long, 50 to 75 feet wide, and 20 to 44 feet deep. Small pits 8 to 10 foot square wore sunk on the ore zone, which extends some 1450 feet to the southwest. The rock containing the minerals is either black or gray shale. The gray material closely resembles limestone. The following minerals have been reported from the mine: quartz, ankerite, calcite, galena, sphalerite, pyrite, chalcopyrite, and bornite. Some of the galena has yielded 10 to 15 ounces of silver and 10 cents in gold per ton. The average grade of the ore as mined is not known. To investigate the downward extension of the ore shoot, the Bureau drilled two holes aggregating 373.9 feet, No additional ore was developed by this work.

Jan 1, 1950

By R. V. Ramani, R. Bhaskar

"While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mi ne environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use.As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined.The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.INTRODUCTIONThe sampling of airborne dust in mines can be done for several purposes. Traditionally, dust sampling has been restricted to the gravimetric measurement of airborne respirable dust to comply with the regulations governing the mining industry. Instruments such as the MRE gravimetric sampler, and personal gravimetric samplers that have collection characteristics similar to the human respiratory system have been in use for the last two decades. Presently available instrumentation for the purpose of regulation have been considered adequate by the Committee on the Measurement and Control of Respirable Dust in Mines (National Academy of Sciences, 1980),"

Jan 1, 1989

By R. V. Ramani, V. T. Burgos, J. A. McClay

Model testing is a two part operation; first, to assure the valid¬ity of the mathematical statements and second, to evaluate the accuracy of the computer model for predictive purposes. Verification of both the conceptual and computational aspects can be achieved through the use of input data for which output results are available for comparison. In this dissertation, two test problems were selected for model testing from the Economic Evaluation Reports of the U.S. Bureau of Mines, Process Evaluation Group. Verification Data Set I Input data for this test was selected from an economic analysis of a hypothetical 1,056,000-ton-per-year mine in a 48-inch bituminous coal seam (Process Evaluation Group-Report No. 72-27, 1972). The mine was scheduled to operate five days per week, three shifts per day, 220 days per year with an estimated life of 20 years. Coal reserves covered an area of 6.4 square miles with an expected recovery rate of 70%. Production was achieved through 4 continuous miner sections with an average production rate of 400 tons per shift. The cost summary in the report included a breakdown of equipment and labor requirements. A depreciation schedule listed the expected capital expense per year of operation, assuming capital replacement with identical units and no change in the unit cost. Supply and oper¬ating costs were listed in both gross annual figures and cost per ton of production. The operating and investment costs were projected over the 20 year mine life and a discounted cash flow analysis performed to determine

Jan 1, 1975

By R. J. SHAW

Oil shale has been defined as, "a compact, laminated rock of sedimentary origin yielding over 35 percent of ash and containing organic matter that yields oil when distilled but not appreciably when extracted with the ordinary solvents for petroleum." The oil-yielding organic matter in oil shale, commonly called kerogen, decomposes upon application of heat to form bituminous materials that are soluble in organic solvents and may be extracted from the inorganic residue. However, separation usually is accomplished by continuing the heating and thereby cracking the primary bitumens to gas and oil, which distill, leaving a carbonaceous material on the mineral residue. It has been suggested that this conversion takes place only at relatively high temperatures - 750°F or higher. On the other hand, other workers have found that transformation may take place to some extent at temperatures as low as 400°F. In either a solvent extraction or a destructive distillation process for separating organic material from the inorganic portion of oil shale, the quantity of heat required to raise the temperature of the oil shale sufficiently to induce a satisfactory rate of conversion of kerogen to oil is important in determining the design of an economical process. Likewise, the quantity of heat recoverable from a spent shale is important in determining the overall heat balance of the process. Published data on the specific heat of American oil shales are meager. Gavin and Sharp present data for two samples of Colorado oil shale, one from near DeBeque and one from Parachute Creek, and for a sample of spent shale over a temperature range of 68°F to 1940°F. McKee and Lydor present data on the specific heat of two samples of oil shale from near DeBeque, Colorado. Additional thermal data on various grades of oil shale over a wider range of temperature are needed in order to apply sound engineering practices to the design of equipment for processing oil shale.

Nov 1, 1947

By G. W. Jones, I. Spolan

"INTRODUCTION The operation of internal-combustion engines at high altitudes and the general aspects of combustion processes in rarefied atmospheres have created considerable interest in the problem of ignition and flame propagation at low pressures. Nuckolls, Matson, and Dufour 4/ have published results on the effect of low pressures on the propagation of flame in gasoline vapor-air mixtures in vessels of large capacity. The volumes of their test equipment varied in capacity from 0.425 to 125 cubic feet. Various sources of ignition were employed. These authors found that the explosive range of gasoline vapor in air decreases with decreasing pressure at pressures considerably below atmospheric, until a limiting absolute pressure of about 33 mm. mercury at ordinary temperature is reached, at which point no appreciable flame is propagated.Experiments carried out at the Bureau with natural gas-air mixtures at reduced pressures have shown 5/ that the limits of inflammability are but little affected at reduced pressures down to 175 mm. mercury. As the pressures of natural gas-air mixtures are reduced below atmospheric, the mixtures become more difficult to ignite; however, if a suitable source of ignition is employed, the limits of inflammability are as wide at 175 mm. mercury absolute pressure as they are at atmospheric pressure. In view of these observations with natural gas-air mixtures, it appears important to investigate gasoline vapor-air mixtures for possible similar behavior. For this reason the tests herein described were carried-out."

Oct 1, 1946

By Kenneth R. Farley

The Bureau of Mines developed a rapid and accurate flame photometric procedure for determining cesium and rubidium in ores and in products associated with the extractive metallurgy of these elements. The effect of associated ions is neutralized by addition of buffer solution; alkali metal effects are neutralized by parallel analyses made on standard solutions similar in composition to the sample being studied. The overall accuracy of the method is within 2.5 pct of the amount of cesium or rubidium present; the range from 1 to 25 pct is the most accurate.

Jan 1, 1966

By H. E. Powell

Magnetic susceptibilities were determined by the Bureau of Mines fur 19 cobalt- and nickel-bearing minerals and for a suite for synthetic cobalt-nickel diarsenides analogous to the rammelsbergite and safflorite series. Relations between susceptibility and composition were found to be nonlinear for both impure natural minerals and pure synthetics.

Jan 1, 1967

By Earl R. Maize

This is the first of a series of reports dealing with development of a method of strengthening bituminous-coal-mine roof. Later reports will describe the progress made with injecting high cohesive and adhesive bonding agents into bedding planes and mine tests of roof strata strengthened by the bonds formed. The concept of strengthening roof strata in coal mines by inserting steel rods in the form of bolts has been widely accepted by the coal industry. The benefits of increased production and safety derived from this type of roof support has more than justified the increased cost of roof bolting. However, not all coal-mine roof structure is amenable to this type of support, and failures occur owing to the heterogeneity and variable character of mine-roof strata.3/

Jan 1, 1957