Search Documents

By Paul Hughes

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining has been employed successfully in mines throughout North America as a method of mitigating exposure to the operator having to work under a seismically active ?back?. This paper reviews design methodology in the placement and analysis of sill mats with reference to site observation coupled with on going numerical and analytically derived solutions.

Jan 1, 2006

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By F. K. OVITZ

In its endeavor to promote a more efficient use of coal the Bureau of Mines, in cooperation with the Illinois State geological survey and the University of Illinois, has undertaken an investigation of the coking of Illinois coals. The investigation was started by collecting from various sources the data regarding experiments already made by others; these data have been compiled and are presented herein. The present methods of using coal seem wasteful. When coal is burned in furnaces for the generation of steam, only the heat gener- ated by the fuel is utilized; possible by-products are not only lost but frequently are the source of the smoke nuisance. The volatile matter containing the tar and heavy hydrocarbon gases is difficult to burn completely in many furnaces, and its decomposition produces black smoke. When coal is coked in a by-product oven, the volatile matter is no longer a nuisance but, on the contrary, is the source of many by-products, including benzol, toluol, gas, tar, ammonia, and cyano- gen, all of which increase the value that may be obtained from coal. The coke that remains after the volatile matter has been driven off is a valuable fuel that can be used for almost all purposes for which bituminous coal can be used, and it is necessary for some metallurgical work. It has about the same heating value as anthracite coal. Because of its cleanness and its burning without smoke, it is well suited for domestic heating and the generation of steam in plants where smokelessness is demanded. The use of coke for these pur- poses would do much to eliminate smoke in cities. The best grades are regarded as essential in many metallurgical processes for reduc- ing ores to their metals. By-product coking in the United States during the past three years has increased greatly. When the ovens now in course of construction are completed, the total capacity of by-product ovens will be more than double what it was in 1913. This increase has led to a search for coals other than those now known to be available for use in by- product ovens. Tests with coals from the southern part of Illinois have indicated that coke from Illinois coal unmixed with other coals can be used for fuel purposes and that coke from mixtures of Illinois coal with low-volatile coking coal might be suitable for some metal- lurgical work. In the tests the yield of ammonia was larger than is obtained from Eastern coal. Evidently the development of methods by which good coke can be made from Illinois coals and the by-products recovered is a matter of high importance. Any investigation that will indicate how, by proper treatment, these coals can be made available to supply the market for coke and gas in the Middle West will increase efficiency in their use, and will aid in conserving the country's supply of high-grade coking coal.

Jan 1, 1917

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By Leonard Obert

This report describes an inexpensive triaxial equipment for testing 2-1 / 8- , 4- , and 5-5 / 8 - inch - diameter rock cylinders subjected to loading conditions comparable to those encountered in underground mining . Only minimal specimen preparation is required . The maximum axial load that can be applied is 250,000 lb , which corresponds to an axial stress of 70,000 psi for the 2-1 /8- inch- diameter specimen . The maximum radial pressure that can be applied is the same for each specimen diameter ; namely , 10,000 psi . The mechanical parts in this equipment are relatively easy to machine and fabricate . The cost of all parts , including the 250,000- lb hydraulic press but not including labor costs , was approximately $ 1,000 .

Jan 1, 1963

By G. E. McElroy, A. S. Richardson

"The Bureau of Mines, in cooperation with the Anaconda Copper Mining Co., has conducted a series of experiments an air measurement in fan-pipe installa¬tions in a Butte mine during the fall and winter of 1922-3. The chief purpose was to determine the friction factors for different types and sizes 3f fan piping, but much attention was devoted to methods of air measurement, not only with respect to the methods used for friction factor tests, but also to com¬parison with other methods.The air flow was measured simultaneously at two points 380.6 feet apart in six different fan-pipe installations, each over 500 feet in overall length, in a rock cross cut adjacent to an air shaft,The air pressure was regulated by two sinoco multivane fans, driven by 7 ½ h.p. motors, the fans being connected in tandem so that one discharged into the intake of the other through a short connector and the latter discharged into the line through a straight connection equipped with a honeycomb of 4-inch squares or S radial vanes to prevent spiral flow of air, At each point where it was desired to measure the air flow, measuring sections equipped with piezometer rings pierced for easy insertion of pitot tubes, thermometers, etc. Piezometer static pressures were used in all the tests as standard, and dynamic or total pressures only were obtained with the pitot tubes, except for purposes of comparison.The tubes had special guide blocks, designed especially for underground work. To insure greater accuracy two tubes were used simultaneously, in order to obtain the velocity pressure at the center of the section simultaneously with that nearer the circumference, so that the mean velocity would be determined as accurately as possible. The tubes were held in proper place by means of flat guide boards. Velocity pressures were measured in manometers."

Sep 1, 1923

By R. L. King, J. Cervik, A. A. Campoli

The Bureau of Mines performed laboratory experiments to evaluate the triboelectric effect of particulate-laden gas streams on polyethylene pipe at various velocity, humidity, dust-size, and dust-load conditions. Charges in excess of 10 kV were produced on the outside and inside surfaces of laboratory pipe samples, when exposed to 40 pct relative humidity (RH) gas stream containing coal dust. However, no charges were produced in laboratory tests that duplicated the over 75 pct RH and dust-free gas streams found in working underground pipelines. Bare cop- per wire, which is wound around the polyethylene pipe in a 1-ft (31-cm) spacing and grounded, eliminated the charge on the outside surface of the pipe, but not on the inside of the pipe surface,

Jan 1, 1986

By Peter J. Clarke

Afghanistan's mineral industry continued to be dominated by the production and export of natural gas, although several mining and related industrial projects, all under the supervision of Soviet technicians, were in the planning stage in 1982. Afghanistan produced minor quantities of barite, cement, coal, fertilizer materials, iron, and lapis lazuli, all for domestic consumption.2 Large-scale projects being investigated were a copper mine and concentrating plant at Ainak, extensive mining of the Hajigak iron ore deposit near Kabul, construction of an oil refinery at Angot, increasing production and processing of natural gas, and implementing an intensive geologic prospecting and exploration program for areas of mineral potential. Afghanistan's gross domestic product (GDP) was estimated at $2.76 billion3 and has remained stagnant for the past several years. Total exports in 1982 were estimated at $700 million, only a marginal increase from the 1981 figure of $694 million. Exports of natural gas to the U.S.S.R. earned $385 million in 1982, representing just over one-half of Afghanistan's total exports. Natural gas revenues were down approximately 11% from the 1981 level, owing primarily to increased antigovernment activity in the northern part of the country.4 About 90% of the country's natural gas production was exported to the U.S.S.R.5 About 38% of Afghanistan's development budget had been earmarked for mining and industrial projects in 1982.6

Jan 1, 1984

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a 'cascading pillar failure' (CPF), occurs when one pillar in a mine layout fails, transferring its load to neighbouring pillars, which causes them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S.A. are documented. Mining engineers can limit the danger presented by these failures through improved mine design practices. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines-the containment approach, the prevention approach and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining at shallow depth. Cascading pillar failure {CPF) in room-and-pillar mines can go by many other names, such as `progressive pillar failure', `massive pillar collapse', 'domino-type failure' or 'pillar run'. In this kind of failure when one pillar collapses the load that it carried transfers rapidly to its neighbours, causing them to fail, and so forth. This failure mechanism can lead to the rapid collapse of very large mine areas. In mild cases only a few tens of pillars might fail; in extreme cases, however, hundreds, even thousands, of pillars can fail. CPF can have catastrophic effects on a mine, and sometimes these effects pose a greater risk to health and safety than the underlying ground-control problem. Usually, the CPF induces a devastating air blast as a consequence of the displacement of air from the collapse area. An air blast can disrupt the ventilation system totally by destroying ventilation stoppings, seals and fan housings. Flying debris can seriously injure or kill mining personnel. The CPF might also fracture a large volume of rock in the pillars and immediate roof and floor. In coal mines and certain other mines this can lead to the sudden release of large quantities of methane gas into the mine atmosphere; a methane explosion might result from the CPF. CPF is at the far end of the spectrum of unstable pillar failure. At the other end are slow `squeezes' that develop over days to weeks and, because of their slow progress, do not pose an immediate danger to mining personnel. There is ample warning time for men and machinery to get out of the way of the failure. In a CPF, however, the failure progresses so rapidly that men and equipment cannot be evacuated in time. Significant seismic energy is released as a consequence of the rapid failure and collapse. CPF should not be confused, however, with coal-mine bumps and rockbursts. In some cases the damage can appear similar, but the underlying mechanics are completely different. As will he shown later, the mechanics of CPF depend on the applied vertical stress and the post-failure, i.e. strain-softening, behaviour of the pillars. In a CPF pillars shed their applied load rapidly and have very little residual strength after failure. The collapse itself may release significant seismic energy, but otherwise the mine is seismically quiet. Alter a CPF the openings in the affected mine workings have usually closed completely. In contrast, coal-mine bumps and rockbursts occur in seismically active mines. Research has shown that coal-mine bumps and rockbursts are seismic events induced by mining that damage underground mine workings. Bumps and bursts are thus a subset of a much larger set of mining-induced seismic events.[ Only some of these seismic events damage mine workings; fortunately, most do not. The mechanisms by which a mining-induced seismic event can lead to a damaging coal-mine bump or rockburst is still a significant research area.2 After a bump or rockhursr the affected mine workings may or may not be completely closed. For example, in the coal-mine bump described by Soler and co-workers2 the mine workings remained open even though the pillars were destroyed during the bump event. Because CPF differs from a coal-mine bump or rockburst, the design approaches to control their occurrence also differ. The design recommendations developed here apply to CPF and not to bump- or burst-prone mines. Cascading pillar failure examples Unfortunately, CPF has occurred in room-and-pillar coal, metal and non-metal mines. The most infamous example is the Coalbrooke colliery in South Africa, where 437 miners perished where [si >1 3at1ttsumsus7car kky vArtMixiL7i nesafr tramwsamn ures] on 21 January, 1960.1 Table I summarizes the mining dimensions of 13 examples of rapid pillar collapse in U.S. coal mines. All occurred during the 1980s and 1990s, and all happened suddenly or without significant warning. Most resulted in air blasts and damage to the ventilation system. Table 2 gives the mining dimensions of six room-and-pillar metal and non-metal mines in the U.S.A. where failure occurred in all probability by the CPF mechanism. The collapse areas can be huge. Fortunately, some of these failures gave advance warning. At the lead-zinc mine slabbing from pillars and roof falls began four weeks prior to the main collapse.3 At the copper mine considerable rock noise and smaller failures preceded the main collapse by five days.5 At the copper-silver mine it is not known if nature provided a warning.6 Evidently, the trona mine collapsed without warning.7,8 Rock noise and other failure warnings preceded the silica mine collapse by three weeks. v The presence or absence of warnings at the salt mint is not known. to Most of these collapses induced a substantial air blast; damage to the ventilation systems was limited, however, to bent airdoors and a few downed stoppings, except at the trona mine where extensive damage to the ventilation system resulted.

By F. E. Armstrong

The Bureau of Mines has conducted a research program to systematize the art of locating uncharted and lost oil and gas wells that penetrate coal seams; this publication presents a preliminary summary of its findings. Although no method or combination of methods will guarantee finding all uncharted and abandoned wells in a particular area, at least 75 percent of such wells can be located by compiling and applying all available information and using modern metal detectors.

Jan 1, 1973

By Wilbert T. Malenka

In its search for a highly productive mining system for anthracite beds pitching from 100 to 200, where conventional mobile equipment cannot be used) the Bureau initiated a longwall project by introducing a shearer drum cutter loader of European origin. Because of the undulating nature of the roof and floor and changing bed thicknesses, the machine proved inflexible and extra work was required in lifting bottom coal and blasting top coal.

Jan 1, 1966

By Edward E. Tate

This is a report on the design, development, and manufacture of a prototype roof bolting machine for high rise applications. The machine is designed to traverse a 32 inch entry and rebolt a roof fall area to a height of 28 feet 10 inches. Covered in the report is a chronology of the project, an explanation of the design problems, and a description of their solutions. The report concludes that the equipment as designed is suitable for the purpose intended and further testing is recommended.

Jan 1, 1981

By D. G. Kuehn

Positive ion sampling studies have been conducted on do discharges containing 0.33 percent sulfur dioxide in helium. Measurements were made for normalized gas pressures from 0.45 to 6.8 torr and discharge currents from 5 to 40 ma. Ion species observed included SO+, S+, SO2+, SO3+; O+, and 0+, 02+. Studies were conducted on the functional dependence of the various ion species with respect to axial distance, pressure, current, and gas flow rate. Interpretation of these results is consistent with the assumption of SO2 dissociation. Deposition of sulfur compounds was observed in the plasma container during these studies. The present results are compared with previous studies which have been conducted in SO2.

Jan 1, 1971

By Henry Kreisinger, F. K. Ovrız

Some of the investigations conducted by the Bureau of Mines have for their object the collecting and disseminating of information regard- ing methods by which the fuels of the country may be most effi- ciently used. As the analysis of flue gases tends to develop better methods of firing, which in turn reduces waste of fuel, the Bureau of Mines in this bulletin presents for the benefit of those in charge of boiler plants and all other persons interested detailed information on methods of sampling and analyzing flue gases, and on the utilization of the analyses in promoting boiler-room economy. This bulletin is intended to be a companion to Technical Paper 80," and is written in plain and nontechnical language, as far as pos- sible, so that it may be readily understood by persons who have not had the advantage of a technical education. Whenever possible, illustrations of apparatus and methods of handling have been used rather than elaborate descriptions. The material presented in this report is arranged in two parts. The first part contains the description of the apparatus and the methods used in sampling and analyzing flue gases. The second part gives experimental results obtained with the different methods of sampling and collecting flue gas that are recommended in the first part of the report. Only simple apparatus and methods are considered, as they are accurate enough to show the large heat losses due to the use of too much air, and are also accurate enough to indicate any incomplete combustion losses of economic importance. Without doubt the loss due to large excess of air is the greatest one in the boiler room, and can usually be greatly reduced by making proper use of gas analysis. Before engineers in the isolated industrial plants can be induced to analyze for small traces of combustible gases, they must be first taught how to analyze for carbon dioxide (CO), and they must learn to appre- ciate the great possibilities of reducing loss from large excess of air. Furthermore, in the face of the great difficulty of obtaining a fair

Jan 1, 1915

By A. T. Iannacchione, D. G. Puglio

The Bureau of Mines established geologic factors affecting the mining of the Lower Kittanning coalbed to aid in coalbed minability studies and examined the occurrence of "wants" (places where coal is missing) and types of unstable roof rock strata. Trends established from mapping, including prediction of areas of high methane emissions, were extrapolated to unmined areas. "Wants" in the coalbed are of two types: Erosional and depositional. Erosional features occur where north-south-trending sand-filled channels cut into the coalbed. Variations in depositional environments have caused the coalbed to "split" into several thinner units. Slickensides, commonly indicative of unstable roof, are adjacent to and on the underside of sandstone channels; they were caused by differential compaction and by soft sediment sliding along the contact between the sandstone and adjacent shale. The frequency of unstable roof also increases where the interval between the Middle and Lower Kittanning coalbed is less than 30 feet. The zones of weakness at the contacts above and below the Middle Kittanning coalbed are the controlling factors for unstable roof in these strata. Methane emissions from the coalbed are controlled primarily by depth, fracture permeability, and rank of coal. Local geologic factors are coalbed thickness, associated rock strata, structure, and proximity to outcrop.

Jan 1, 1979

By Philip W. Holland

The U.S. Bureau of Mines has developed an improved method for determining dissolved helium in water in the concentration range of 4.0 x 10-8 to 270 X 10-8 cm3 He (STP)/cm3 H2O. The method is a modification of a previously reported method that was developed for analrzing surface and subsurface waters in geochemical survey work. Water samples are collected in SOD-cm stainless steel cylinders, and the dissolved gases in a sample are extracted into an evacuated cylinder of equal volume. After addition of 30 psig of nitrogen containing less than 2 ppb helium to the extracted gases, the resulting mixture is analyzed for helium using a helium-tuned mass spectrometer. The helium content of the water sample is determined from an empirical calibration that is established by analyzing standard solutions of helium in water. The accuracy of the method is ±7 pct for helium-in-water concentrations above 10 x 10-8 cm3 He (STP)/cm3 H2O.

Jan 1, 1989

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

By J. Weinberg

This Bureau of Mines report presents data on the changes in the use of steel in motor vehicles over the past 35 yr. Sources of supply of steel for the automotive sector have shifted from almost all domestic in the 1950's to about 50% domestic and 50% foreign in the 1980's. Downsizing, design changes, and substitution of lighter weight materials to achieve energy efficiency also contributed to the market loss of the domestic steel industry. Although plastics and aluminum have displaced some steel in motor vehicles over the years, heavy low-carbon steel is now being replaced most rapidly by lightweight high-strength steel. If the percent of domestic steel used in motor vehicles had not declined since 1950, domestic industry would have supplied 9.3 million more short tons of steel than it supplied in 1985. Downsizing and design changes accounted for 43% of the loss; steel imports, 32%; and substitution of plastics and aluminum, 25%. In 1985, the total value of market share lost by U.S. steel producers was $5.1 billion, of which $1.6 billion was lost to foreign steel producers and automobile manufacturers. Through aggressive marketing and increased efficiency, however, the domestic steel industry may be able to recapture some lost markets, as applications for high-strength steels expand, and as foreign-owned automotive plants in the United States provide fresh sales opportunities.

Jan 1, 1988

By James R. Welty

Heat content values were experimentally determined for yttrium metal between temperatures of 400° and 1,300° K and for iron pentacarbonyl between 301° and 380° K. The drop technique was used; that is, a sample of material sealed in a protective capsule was heated to 3 desired temperature in a furnace and then dropped into an ice calorimeter. A revised technique for determining heat content values from calorimetric data is described. Heat content and corresponding entropy-increment data above a reference temperature of 298.15° K are presented in tabular form. Equations for heat content and heat capacity as functions of temperature were derived for each substance. These equations are [Y (c): HT-H298.15 = 1.2041T 1 3.393 x 10-3T2- 0.4176 x 10' T"1 + 739.9 cal/mole Cp = 1.2041 + 6.786 x 10-3T + 0.4176 x 106-T-2 cal/deg mole Fe (CO) E, (1) : HT - H298.15 = 55.636T - 16,588 cal/mole Cp = 55.636 cal/deg mole]

Jan 1, 1963

By K. O. Bennington

Enthalpies of formation of three sodium titanates were determined by hydrofluoric acid solution calorimetry, The values obtained for formation from the elements at 298.15° K are -370.9±0.5 kcal/mole for Na2TiO3, -832.1±0.9 kcal/mole for Na2Ti307, and -1,510.9±1.7 kcal/mole for Na2Ti6013. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and from the component oxides for Na2Ti03 and Na2Ti307.

Jan 1, 1973