Search Documents

By Martin J. Gavin

During the recent study of lubricating oils carried on in the San Francisco laboratory of the United States Bureau of Mines, it became desirable to distill the oils used in the experimental work at pressures as low as 10 millimeters (mercury column) absolute. In the effort to Overcome difficulties and eliminate sources of error, certain changes were made in the apparatus for vacuum distillation used by the Bureau of Mines for crude petroleum.4 These changes were described in R.I. 2819, issued in July, 1927. Subsequent to the publication of R.I. 2819 several other changes have been made, and the present form of the apparatus for vacuum distillation of lubricating oils is described in this revision of R.I. 2819. These changes were found to give more accurate checks on duplicate distillations. The major part of the credit for the laboratory work which developed the changes in the apparatus and method revised herein is due to Boyd Guthrie, assistant petroleum chemist, and R. V. Higgins, junior chemist, o the San Francisco laboratory, United States Bureau of Mines. DESCRIPTION OF APPARATUS The distilling flask employed is essentially the Hempel flask as used by the United States Bureau of Mines for the analytical distillation of petroleum.5 he complete apparatus is shown in Figure 1. The fractionating column and exposed portion of the flask is wrapped with 4 inch asbestos rope and then surrounded by a cylindrical hood of 1/8 inch pliable asbestos sheet with a narrow air space between the wrapping and the cylindrical hood. This was found necessary to prevent any radiation or convection heat losses from the column, and resulted in obtaining a more even and constant fractionation by eliminating any dephlegmating action caused by temperature changes around the column.

Jan 1, 1930

By Thomas H. Dubaniewicz

Thirteen miners died as a result of 2 explosions in the Jim Walter Resources No. 5 mine near Brookwood AL in September 2001. Both explosions were ignited in intake air entries, and both were probably ignited by electrical equipment. With few exceptions, permissible equipment is not required in intake air entries of US underground coal mines Researchers with the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. studied the electrical equipment ignition sources for the Brookwood and other w disasters to develop recommendations for preventing similar disasters Adherence to National Electrical code® requirements for flexible cords installed in hazardous (classified) locations may have prevented the second massive Brookwood explosion. The 30 CFR Part 7 requirements for battery assemblies should be reevaluated, taking into consideration United Mine Workers of America recommendations and the Zone 1"increased safety" standard requirements for battery assemblies, Class 1 Division 2 or Zone 2 explosion protection techniques are recommended for intake air equipment so that they do not present a methane air ignition source under normal operation before mine power is shut down during emergencies Battery powered circuits intake air that are likely to remain energized during emergencies should be protected by more stringent protection techniques, to protect rescue/recovery personnel. Index Terms -Class 1 hazardous location, mine explosion, flexible cord, battery assembly, permissible equipment

By G. W. Birge

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. The selection of coal beds in Westmoreland County for coking tests was based, in part, on estimates of the coal reserves by Dowd,3/ who estimated the recoverable reserves in beds 28 inches or more thick, in thousands of tons, as follows: [ ]

Jan 1, 1957

1. In 2003, a total of 7,070 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA). The largest percentage of all mining sectors was sand and gravel mines (49.1%). • Sand and gravel mines are found throughout all 50 states.

Feb 1, 2005

By R. R. Wells, W. W. Agey

"INTRODUCTION Oxide manganese ore from the Sheep Mountain property was of intermediate grade (23.0 percent manganese) and contained silica as the major impurity. The deposit from which the ore was taken is known as the Sheep Mountain manganese property and is 8 miles west of Durkee, Oreg. Test work was done in the metallurgical laboratories of the Bureau of Mines at Salt Lake City, Utah, on representative samples cut from a 290-pound shipment of crushed ore submitted by the Oregon State Department of Geology and Mineral Industries and reported to be typical of the Sheep Mountain deposit.ACKNOWLEDGMENTSThe authors wish to acknowledge the assistance of R. S. Doan, former assistant director of the Bureau of Mines, under whose supervision the manganese program was initiated in 1940, and, the valuable suggestions made to them by S. R. Zimmerley, now chief, Salt Lake City Division, Metallurgical Branch. Acknowledgment also is made to H. G. Poole and C. H. Schack for their suggestions and contributions to the organization and prosecution of the work of the Ore Dressing Section. Microscopic work on the ores and many ore-dressing products was done by L. G. Evans -and the late. B. E. Head. Our appreciation is extended also to H. E. Peterson, chief chemist, and members of the analytical staff for the many analyses made of the ores and ore-dressing products."

Nov 1, 1947

Develop a simple and economical technique for determining the absolute stresses and the change of stress on the surface of roofs, floors, or walls in miners. Approach Use a commercially-available, permissible, Whittemore-type gage to determine the stress at the surface of a mine opening and to monitor any stress changes that might take place. How It Works The following equipment is used: ? One steel templet (for laying out a 60° rosette on the: rock surface). See first photograph. ? One 3/8-inch rock drill bit for drilling holes for the rosette pins. ? Six stainless-steel rosette pins. ? One Whittemore-type mechanical strain gage. ? One drill (not shown). ? Epoxy for cementing the rosette pins. ? Tape to hold the pins while the epoxy sets. The following procedure is used to determine the absolute stress on the rock surface. 1) Spot the location of the rosette pins with the templet. 2) Drill the pin holes and set the pins with epoxy cement. 3) Measure and record the distance between the pins across three diameters of the rosette with a 10-inch Whittemore-type gage. See diagram. 4) Drill a 1 1/2-inch diameter hole in the center of the

Jan 1, 1981

By Harry R. Nicholls

As part of the pre- and post - shot mine examination at Project GNOME , acceleration data were recorded underground from a series of chemical explosive shots . The cube root of the charge weight was used to scale acceleration and distance because charge weight was not constant . Regression analysis of particle acceleration - distance data gave the following propagation equation : A W1 /3 = 5.10 x 105 ( R / W¹ / 3 ) −2 .43 The quantity A W1 /3 is scaled particle acceleration expressed in g's - lbs¹ / 3 , and R/W1 /3 is scaled distance expressed in ft / lbs¹ /3 Data obtained from the nuclear explosion were scaled and fall within one standard deviation of the calculated propagation law for the smaller shots . Cube root scaling laws were adequate to group acceleration data from explosive charges varying by a factor of more than 1 x 10 in charge weight and over shot - to - gage distances varying from 100 to 46,000 feet . Data obtained from a series of small tests provided sufficient data from which reliable predictions of acceleration could be made for the large nuclear explosion .

Jan 1, 1964

By R. K. Koch

The vapor pressures of liquid molybdenum and liquid zirconium were determined by the Langmuir free-evaporation method. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. The vapor-pressure data led to the following equations: [log p (atm) = 5.429 - 28,380 T for liquid molybdenum in the range 2,890° to 2,990° K, and log p (atm) = 6.521 - 30,940 T for liquid zirconium in the range 2,229° to 2,795° K.] Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 157.6 ± 1.8 kcal/mole and 148.4 ± 2.4 kcal/mole for molybdenum and zirconium, respectively, where the uncertainties are two standard devia¬tions. Second-law standard heats of sublimation determined from sigma plots and tabulated enthalpies were 143.5 ± 2.7 kcal/mole and 149.2 ± 3.8 kcal/mole for molybdenum and zirconium, respectively. The better agreement in heats of sublimation for zirconium is attributed to the 566° K temperature range studied which permitted a more accurate definition of the vapor pressure curve than could be obtained from the 100° K span for molybdenum. This supposition was verified by making a sigma-prime plot which utilized solid vapor pressure data for molybdenum to extend the evaluation range by 800° K. This gave a standard heat of sublimation of 155.2 ± 1.6 kcal/mole which is in good agree¬ment with the third-law value. The plot also gave a standard entropy of sublimation (298.15° K) of 35.73 ± 0.48 eu.

Jan 1, 1968

By J. E. Tiffany, Z. C. Gaugler

This supplement has been prepared to furnish information on amendments to the regulations that were approved by acting secretary of the Interior on June 24, 1946, while this report was in the press. Page 14, item 2, and page 20, item 4, have been amended by the addition of the following footnote: "Pending the development of a satisfactory multiple-shot permissible blasting unit, a blasting unit of Type II, Class A, covered by Federal Specification WB 411, December 31, 1941 (with or without Amendment 2, June 16, 1945), may be used until Decem- ber 31, 1947. Should a satisfactory multiple-shot permissible unit be made available prior to that date, this interim approval may be terminated." Page 14, footnote / has been amended to read as follows: "The use of charges over 1-1/2 pounds and not exceeding 3 pounds is approved pending further investigation. The approval, which may be withdrawn at any time, expires December 31, 1947, unless renewed. For charges over 1-1/2 pounds, the following additional requirements must be observed: (1) Shot holes must be 6 feet or greater in length. (2) Explosives must be charged in a continuous train with no cartridges deliberately deformed or crushed, with all car- tridges in contact with each other, and with the end cartridges touching the rear of the hole and the stemming, respectively. (3) The permissible explosive must be one showing toxic gas omission that will place it in either Class A or Class B."

Jan 1, 1947

By D. E. Stone

Solid and liquid impurities must be removed almost completely from synthesis gas for the production of synthetic liquid fuels because of their effect on the synthesis catalyst and turbocompressors. The maximum permissible concentration of dust has been set at 0.05 grain per 100 cubic feet.5/ This is one part per million by weight, or about the same concentration as in average city air. The cost of synthesis gas is estimated to constitute 60 to 70 percent of the total cost of the synthetic liquid fuel. For this reason this station is developing processes using coal instead of the more valuable coke as raw material, which promises reduction in cost of the synthesis gas. This, however, increases the difficulty of attaining the above dust value. As failure of the dust-removing equipment to produce high-purity gas may ruin valuable equipment within a few minutes, it is imperative that a reliable and continuous method be obtained for determining such extremely low concentrations .of dust in the purified gas. A suitable device must also instantly sound an alarm and, if necessary, automatically actuate the proper valves to prevent damage. The Ess Instrument Co. designed and built an instrument which they believed might fulfill these specifications. It' continually compared, by means of photoelectric cells, the intensity of a light beam passing through the gas and a similar beam passing through clean air. For maximum sensitivity, the photocells were connected back to back, i.e., anode to cathode and cathode to anode. The difference in voltage produced by the two cells was amplified and operated an indicator.

Jan 1, 1951

By Chas. G. Maier

The bright annealing of copper is an industrial practice of considerable importance. In connection with this process, equilibrium concentrations of carbon monoxide and dioxide, which may exist in contact with copper and cuprous oxide at elevated temperatures, are of interest. Data obtained at the Pacific Experiment Station of the U. S. Bureau of Mines enable estimates of these equilibrium concentrations to be made in two independent ways. Although the publication of final data on one method can not take place until certain further experimental work is accomplished, repeated requests which the Bureau of Minus has had for data relative to the annealing and deoxidation of copper justify the present preliminary report. This paper deals with the calculation of gas concentrations in the reduction of cuprous oxide, using more scientific data which will be published later, and refers especially to those conditions of temperature and concentration of practical implication, and from which critical limits ensue.

Jan 1, 1929

By Joseph P. Flick, Kathleen M. Kowalski, Lynn L. Rethi, Roberta A. Calhoun

Many miners are involved in tasks at the mine site that are similar to those sub-tasks performed in general construction, maintenance and repair (CMR) type work activities. As a result, many of the injuries in the mining industry today can be traced to employees performing these CMR type work activities. Indeed, a recent analysis of a major aggregate company revealed that 65% of all injuries documented originated from performing such CMR activities. It is hypothesized that the number of injuries to miners performing construction, maintenance and repair (CMR) work activities on mine property may be reduced through improved training that focuses on better hazard recognition using the numerous visual and other cues that are available for evaluating workplace health and safety hazards. To this end, researchers at NIOSH’s Pittsburgh Research Laboratory have merged two proven methods of training miners to recognize hazards, stereoscopic (3-D) slides and the concept of degraded images, into this training program. Stereoscopic (3-D) slides have been shown in earlier NIOSH and U.S. Bureau of Mines research to be an effective training aid for improving the ability of miners to recognize various geologic and mining-induced irregularities that can cause groundfalls.3 They realistically portray the natural mine environment, and thus are an excellent training aid for teaching miners to recognize such visual cues. The degraded image concept, originally developed by the military and used for target detection training, describes scenes where the target is partially hidden by cloud cover, dust, rain, natural barriers, buildings, or other obstructions that can camouflage or confuse the target. Research had shown that flight observers who were trained with less than ideal (or degraded) pictures were more successful in subsequent identification of targets than those trained using ideal (or highlighted) pictures of targets. In order to investigate this concept for training miners to recognize hazards, NIOSH researchers developed a prototype hazard recognition training program using such mining scenes. A control program based on traditional highlighted mining scenes was also developed. Both programs were applied to subjects in a field experiment. Results indicated that miners trained with the degraded images did significantly better on a follow-up test of hazard recognition.4 This hazard recognition program teaches trainees to look for hazards in a more realistic manner than that of the control program. This specific training program for CMR activities involves using the degraded image concept and 3-D slides. The module is designed to educate workers on hazard identification techniques and safe work practices. It focuses on teaching miners techniques for recognizing visual (sight) cues, and then uses these cues to evaluate mining conditions. It should be stressed that other senses, such as sound can also play an important role in hazard detection.

Jan 1, 1999

By Joseph W. Martin

The Bureau of Mines investigated the backscattering of low-energy gamma rays as a method for rapidly determining the incombustible content of coal mine dust. In this method, 60-kev gamma rays from americium-24l penetrate the dust and are reflected by elements in the dust to a thin crystal scintillation detector. The number of backscattered gamma rays is proportional to the incombustible content. Tests of 40 dry, mine-dust samples containing 50 to 100 percent inert material show an average error of 2 percent. Calibration of the apparatus is necessary for each rock dust to account for variable composition. Results for samples containing more than 6 percent moisture are subject to error, but the values are lower than values obtained by chemical analysis, and thus fall on the safe side. Development of a small portable meter based on the backscatter principle appears feasible. Such a meter would find application within coal mines to check the effectiveness of rock dusting procedures.

Jan 1, 1968

By R. E. Hall

When the criterion for control of scale prevention on the evaporating surfaces is made the conditions in the concentrated boiler water, then this control becomes an exact operation amenable to an accuracy commensurate with all other operations in the boiler room. The responsibility in boiler water conditioning, however, includes more than clean surfaces. Corrosion in feed lines, economizers and the boiler is a function of the condition of the later, and must be controlled. Steam line and turbine blading deposits must be obviated by the system of conditioning. By the chemical treatment employed, the amount and character of noncondensable uses in the steam must be controlled in accordance with the intended use of the steam. All. in all, the responsibility in boiler crater conditioning ends not with the entrance of the water into the boiler but with the passage from the boiler nozzle of steam, the dryness and rarity of which are defined by the uses to be made thereof. A clearer conception of the scope of boiler water conditioning can be obtained by reference to a diagram of the surfaces (Figure 1) at which it functions. Consideration of this diagram leads to the following outline for the problems of boiler water conditioning: (a) Prevention of scale formation on surfaces (1) In contact with water but at which no evaporation occurs. (2) At which evaporation is occurring.

Jan 1, 1926

By J. B. Stephenson

The Bureau of Mines, under an interagency agreement with the Department of Energy (DOE), investigated the feasibility of hardfacing the critical surfaces of valves and similar devices by chemical vapor deposition. The purpose of this research was to increase the wear resistance of these components for use in the abrasive and erosive environment of coal gasification units. Tungsten and molybdenum coatings were produced on nickel-plated carbon steels and stain-less steels by hydrogen reduction of the metal hexafluoride at 325° to 600° C. Titanium nitride coatings were produced on low-carbon steels by the reaction of titanium tetrachloride, hydrogen, and nitrogen at 1,000° C. Titanium carbonitride coatings were produced on low-carbon steels by the reaction of nitrogen, hydrogen, and methane at 900° C. Tungsten, molybdenum and titanium nitride coatings were formed on 6-, 10-, and l2-inch (0.15-, 0.25-, and 0.30-meter) ball valve seats for evaluation in the low-Btu coal gasification pilot plant at the Morgantown Energy Research Center, Morgantown, W. Va.

Jan 1, 1979

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite having length to diameter ratios of 3:1, 2:1, 1:1, and 0.5:1 were broken in axial compression to determine whether lateral end constraint affected the breaking strength. Steel rings bonded to the ends of the model pillars with epoxy provided, during the loading cycle, a lateral end constraint of about 17 to 30 percent of the average axial stress. The effect of this constraint was to increase the breaking strength of the rock as compared to cylindrical pillars without constraint. The percentage increase in breaking strength varied with rock type and increased as the length to diameter ratio decreased. The maximum increase in breaking strength was 35 percent for marble pillars having a length to diameter ratio of 0.5:1. A theory was developed which relates the expected constraint to the physical properties of the ring and rock.

Jan 1, 1968

By E. L. Rawlins

A previous report4 has explained that pipe lines for the transmission of natural gas should be buried to minimize temperature fluctuations because when excessive the latter decrease accuracy in measuring gas volume and increase leakage of gas due to expansion and contraction in the pipe joints. These effects are governed by the rapidity of the temperature fluctuations and by the total variation over a period of time. The temperature of gas flowing through a pipe line depends to a large extent, upon the temperature of the ground adjacent to the pipe; hence, fluctuation of the ground temperatures at various depths determines the economic depth at which pipe lines should be buried. Scope and Purpose of Report This report covers a record of the daily atmospheric temperature fluctuations at Bartlesville, Okla., for 12 months and a-similar concurrent record of the temperature variation 1, 2, 3, and 4 feet below the surface of the ground.

Jan 1, 1928

By H. A. Johansen

Recent advances in the metallurgy of chromium have enabled this metal to begin to take its place among the refractory metals. Considerable work is being done on the development of high-temperature alloys containing high percentages of chromium.1/2/ In spite of the relatively large amount of work done on these alloys, little is known of the properties of the pure metal. Information in the literature concerning the tensile properties of pure chromium metal is quite scant. This deficiency maybe explained by the great difficulty of preparing test specimens from such a brittle material, resulting in many losses in each phase of the specimen preparation and testing procedure.

Jan 1, 1954

By Lars Osen

The Bureau of Mines investigated (1) the effect of torsion on yield and ultimate strengths of bolts when the torsion is applied first and tensile load is applied independently of torsion and (2) various methods of increasing the tension-torque ratio and/or narrowing the data spread of the tension-torque relationship. A special torsional attachment was fabricated to attach to a universal testing machine to independently subject rock bolts to combined tensile and torsional loads. It was found that initially installed torsion is nullified during tensile loading and the tensile yield and ultimate strengths are not significantly reduced. Lubricating various components of a bolt assembly or using hardened washers will improve the tension-torque relationship during conventional installation; however, the torsional load is not nullified during this type of loading. Hence, a bolt is subjected to a combined stress throughout the loading cycle; the yield point will thus be lowered compared with the pure tensile yield if care is not taken during installation to stay below the torsional yield.

Jan 1, 1966

By W. E. Dennis

"INTRODUCTION The strategic importance of zinc warranted investigation of the Silver Eagle zinc prospect, which was first examined by an engineer 3/ of the Bureau of Mines in January 1943.From October 12, 1943, to March 16, 1944, the Bureau explored the deposit by trenching, core drilling, and sampling to establish the amount and grade of ore and to test for the presence of sulfide-ore minerals at depth.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Oct 1, 1946