Search Documents

By V. C. Petersen

The titanium-rich end of the titanium-germanium system was investigated by x-ray and metallographic methods and verified by resistivity and dilatometer measurements. A constitution diagram is proposed. The titanium-rich portion of the phase diagram is characterized by eutectic and peritectic reactions. The eutectic composition is 19 percent germanium, and the eutectic temperature 1,360° C. The peritectic reaction occurs at 905° C. and 4 percent germanium. Germanium is soluble in alpha titanium to a maximum of 4 percent at 905° C. and in beta titanium to a maximum of 12.5 percent at 1,360° C. Both limits of solubility decrease with decreasing temperatures. Although substantial quantities of germanium are soluble in beta titanium, beta is not retained on quenching. The beta phase probably transforms to alpha by a martensitic reaction.

Jan 1, 1957

By E. Chin

The production of crude mineral commodities in Bangladesh was limited to natural gas, a small amount of construction materials, and clay for ceramics and bricks. No metallic minerals were mined. The only mineral commodity of economic significance was natural gas. Natural gas production has 'been climbing steadily and becoming an increasingly important source of energy for the country. Proved gas reserves were over 4.5 trillion cubic feet, but the amount has been increasing as exploration discovers large new deposits. Some sources quote reserves at over 10 trillion cubic feet.

Jan 1, 1984

By James P. McGee

Preliminary calculations show an economic advantage in using nuclear energy to supply the endothermic heat required for gasifying coal. It should be noted that the various assumptions used in preparing these calculations must undergo further evaluation through additional engineering design and research. The proposed system for gasification is the indirect process cycle with helium heated in a nuclear reactor and passed through an exchanger-type gasifier for the reaction of coal and steam to form CO (carbon monoxide) and H2 (hydrogen gas).

Jan 1, 1960

By Bill M. Stewart, Philip W. Patton, Curtis C. Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines we revisited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968

By Samuel P. Harteis, Eric S. Weiss

The National Mining Association and the Mine Safety and Health Administration requested that the National Institute for Occupational Safety and Health (NIOSH) conduct full-scale evaluations of a recently developed carbon fiber-reinforced polymer (CFRP) reinforcement technique for upgrading existing mine ventilation seals to withstand an explosion pressure of 50 psi or greater. The evaluation was conducted in the NIOSH Pittsburgh Research Laboratory’s Lake Lynn Experimental Mine (LLEM) near Fairchance, PA. The purpose of the evaluation was to determine the blast resistance of the CFRP reinforcement technique, designed to increase the strength of two types of existing 20-psi-rated in situ mine ventilation seals. Two candidate ventilation seals were selected to represent the 20-psi alternative seal designs typical of those used in mines prior to July 2006. Installed within the LLEM were (1) a 4-ft-thick pumpable cementitious foam seal using material with a designed 150- to 200-psi average compressive strength at 28 days and (2) a 24-in-thick, low-density cementitious block seal with a center pilaster and keyed to the floor and ribs. The materials necessary for the CFRP reinforcement technique were then installed on the outby (active) side of each seal, and the seals were subjected to explosion overpressures. Both seals with the CFRP reinforcement retrofit successfully withstood explosion pressures of 60 psi or greater during the full-scale evaluations in the LLEM.

Jan 1, 2008

By E. V. Cilento, K. A. DiGregorlo, R. C. Lantz

A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared to experimental results obtained from single rat PAM. The O2 - was quantified by measuring the reduction of nitroblue tetrazolium (NBT) to a diformazan precipitate (NBTH2) from video-recorded images of individual cells. The kinetic model considered three reactions: (1) the production of extracellular 0 - from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, (2) the subsequent dismutation of o2- to from O2 , and (3) the reaction of o2- and NBT. NBT specificity for o2- was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) which catalyzes the dismutation of o2- to H2o2. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations since NBT is a relatively small molecule (818 MW) compared to SOD (34000 MW). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/or electrostatic effects since SOD is also negatively charged.

Jan 1, 1988

By Kenneth J. Miner

Pittsburgh bed and Lower Freeport bed coals were tested in the U.S. Bureau of Mines two-stage froth flotation pilot plant, which utilizes a new flotation process to remove pyritic sulfur. The process consists of a first-stage coal flotation step to remove coarse, free pyrite and other refuse in the tailings. The clean coal froth concentrate is then repulped and treated with a coal depressant, a pyrite collector, and a frother to selectively float the remaining pyrite in a second stage. Results in the pilot plant were excellent, comparing well with those obtained in laboratory batch tests. That is, about 70 percent of the pyrite present in the Pittsburgh bed coal and about 90 percent of the pyrite present in the Lower Freeport bed coal were removed with excellent final clean coal recoveries.

Jan 1, 1973

By Frank E. Federspiel

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 47,000-acre Electric Peak study area (part of the formerly-designated RARE II Non-wilderness Recommended Area no. 1609) to evaluate its' identified mineral resources. The study area is in Powell and Jefferson Counties, YT, about 30 mi southwest of Helena and 30 mi north of Butte. Three lode localities within the study area contain an estimated 159,000 tons of identified subeconomic resources containing gold, silver, and accessory lead, copper, and zinc. Resources at those localities range from 10,000 to 134,000 tons with grades ranging from 0.04 to 0.32 oz/ton gold, 0.92 to 16.42 oz/ton silver, 0.14 to 79.65 percent lead, and as much as 0.41 percent copper and 0.68 percent zinc. One property also contains 0.15 percent antimony. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that further exploration may identify resources on seven additional study area localities.

Jan 1, 1988

By Paul R. Coyle, Anthony T. Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and LaurelHill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super-pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereo net, and rose diagram projections so that the Loyalhanna’s structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts, pillar sizes, etc., that lessen miner exposure to these hazards.

By T. A. Kubala

Electric discharge ignition has been reinvestigated in a modified Hartmann apparatus for lycopodium powder with air. Minimum stored energy to ignite air dispersions of lycopodium was 25 to 30 mj; ignition occurred with 1 gram of lycopodium dispersed into the 2.7-liter vessel. Ignition energy was measured as a function of the weight of powder used, although some reservations are expressed concerning the uniformity of the lycopodium-air mixtures. In particular, wall layers of lycopodium, remaining after dispersal of 1 gram of lycopodium, were as easily ignitable as the most easily ignited air dispersion. Thus, an unanswered question has arisen concerning the role of surface coatings in the flammability of all marginally ignitable mixtures.

Jan 1, 1981

By D. A. Doughty

The Bureau of Mines developed two methods for determining iron II and iron III in 2- to 5-mg samples of coal using electron paramagnetic resonance (EPR) spectrometry. One method used solid coal samples; the other method used aqueous solutions. The method using solid samples was more simple, technically, but required the use of X-ray fluorescent analysis, or another independent method, for determining total iron in the samples, and the results were subject to some uncertainty. The method using aqueous solutions appeared capable of greater certainty and did not require additional methods of total iron analysis but was more involved procedurally. The coals analyzed were found to contain much more iron II than iron III.

Jan 1, 1973

By I. N. Beall

The present survey indicates 'that the average volatility of motor gasoline now being marketed throughout the country falls well within the limits of Federal Specifications. As would be expected, there is a slight decrease in volatility as compared with the gasoline marketed last wine:., but on the average the gasoline sold today is about the same as that sold last summer. During the past five years the Bureau of Mines has made semi-annual surveys of the gasoline marketed in the United States. To obtain a sample of each gasoline sold is obviously impracticable, but the cities in which samples have been collected have been so chosen as to be representative of the more important marketing territories. It is believed, therefore, that the samples obtained are indicative of the quality of gasoline marketed throughout the country.

Jan 1, 1925

To provide coal operators with an easy-to-use stress control design procedure to minimize coal mine bumps during room-and-pillar retreat mining conducted with available continuous mining machine technology. Approach The goal of this U.S. Bureau of Mines (USBM) re¬search was to facilitate safe and efficient room-and-pillar retreat mining of bump-prone coalbeds by limiting coalbed stress adjacent to expanding gob areas through variation of section layouts. The first step was design of total-extraction pillars and their associated pillar-extraction plans. The second step was development of a coalbed strength model. The third step was development of stress limit design criteria. The fourth and final step was development of a methodology to estimate the magnitude and distribution of development and abutment loads apllied to the pillar line. The linear geometry of unlimited-width sections allowed for the accomplishment of step four with the tributary-area and linear shear-angle concepts. Increasing overburden depths required limited-width sections separated by barrier pillars to control stress within total-extraction panels. The accomplishment of step four with limited-width section designs required prediction of abutment load distributions for rectangular gobs and apportionment of these loads over mixed pillar sizes. A parametric study of the complicated interaction of various combinations of overburden depths, total-extraction panel widths, and abutment pillar widths was conducted with the USBM-developed boundary-element program MULSIM/NL.

Jan 1, 1995

By Charlie Wyche

The principal minerals produced in the Dominion of Fiji in 1982 were unrefined gold, silver, and tellurium. The combined value of these commodities was about $16 million,2 representing over 85% of the total value of mineral output. Cement, sand and gravel, and quarry products were the other minerals produced in Fiji. Despite the small part played by minerals in Fiji's economy, exploration on land and in the coastal areas was carried out by several international mining companies representing Australian, British, Canadian, West German, and U.S. interests. At the end of 1982, 30 prospecting licenses covering 2,300 square kilometers were issued. Most licenses were for copper, zinc, gold, and silver. Total expenditure on mineral exploration was $3.5 million.

Jan 1, 1984

By Thomas H. Dubaniewicz

Fiber optic systems are being deployed in locations where explosive gas atmospheres are normally present or are present under fault conditions. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (NIOSH, PRL) conducted a study of laser safety in potentially flammable environments. Researchers conducted experiments to estimate the mean and standard deviation of laser powers needed to ignite 6% methane-air atmospheres using single mode optical fiber tips covered by two types of iron oxide (Fe304 and (FeMn)203) mixed with a ceramic adhesive. The iron oxides, heated by a 1064 nm continuous wave laser, ignited the methane-air mixtures ,at similar powers. The minimum igniting power and maximum non-igniting power (10 tests) were 407 and 350 mW, respectively, using a 62.5 pm fiber. Laser beams guided by 125 and 80 pm diameter cladding single mode fibers produced similar methane-air igniting powers. Ignition was not observed using coal particles at powers that produced ignition with the iron oxides. Threshold ignition delays using the single mode fiber were approxinlately proportional to the inverse square of the igniting power. Ignition delays were significantly longer than the reported activation time for a comnlercial fiber optic power limiter. Comparisons are made with the results of other researchers. Published by Elsevier Ltd.

By K. Robert Dorman

This Bureau of Mines report describes laboratory and field experimentation in building mine ventilation stoppings, air-door frames, and fan bulkheads with a civil construction technique. Shotcrete is applied to a free-standing, three-dimensional wire-truss panel, which is easily cut and rapidly erected. In mines where shotcrete equipment is available, this technique should be faster and cheaper than conventional block-and-mortar or monolithic concrete construction.

Jan 1, 1980

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter is practically the same 'as that sold a year ago. In fact, there has been little char sin this commodity during the year, as the gasoline sold last summer was almost as volatile as that marketed last winter. Boring the past eight years, the Bureau of Mine's has made semi-annual surveys of the gasoline marketed in the United States, the survey just completed being the fifteenth in the series. The cities in which samples have been collected have been chosen as representative of the more important marketing territories as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1927

By Roy H. Grau, John C. LaScola

"This Bureau of Mines report contains a tabulation of methane emissions during 1980 for all coal mines located in the United States with emissions greater than 0.1 MMcfd. Listed for each mine are methane emission quantity, location, and coalbed. The report also compares records of 1975 and 1980 and describes relationships between emissions in 1980 and the Bureau's coalbed gas content data on 11 mines.INTRODUCTIONMethane gas is a threat to safety in underground coal mines. Research by Government and industry has led to great gains in reducing methane gas ignitions and explosions. The development of advanced methane control techniques is necessary for the safe operation of more gassy mines and the implementation of rapid mining techniques.As part of this research, the Bureau of Mines has surveyed total methane emission data from underground bituminous coal mines in the United States and tabulated emissions from mines producing over 0.1 MMcfd of methane. This report is an update of similar studies previously described in Information Circulars 8733, 8659, and 8558 (2-4).3The data from 1980 were compiled from Mine Safety and Health Administration (MSHA) records of air quality-quantity inspections made quarterly at each mine. The inspections involve measuring airflow and collecting air samples in the main returns. From these data, an average methane emission is calculated and used to represent the daily mine emission for each quarter. The methane emissions given in this report are the averages of the four 1980 quarters and do not include mine emissions from other sources such as degasification projects. Since a previous Bureau study showed that emissions from mines emitting less than 0.1 MMcfd represented only 2 pct of all emissions, 0.1 MMcfd was chosen as a lower limit for data collection (4)."

Jan 1, 1982