Search Documents

By Donald O. Capstick

In 1981, U.S. Bureau of Mines personnel conducted a survey of claims and prospects in the Wheeler Ridge RARE II area to determine if mineral resources or potential for resources exists at deposits in the area. Results of Bureau of Mines investigations indicate the area contains no identified mineral deposits. However, the geologic setting at the Round Valley Peak Prospect near the center of the study area is considered to be favorable for the discovery of tungsten resources with associated molybdenum and copper. Tungsten deposits, should they be present, would be expected to occur at depth in tactite at or near the calcareous rock-granite intrusive contact. Sand, gravel, and stone deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 16,200-acre (6,560 ha) Wheeler Ridge study area is 11 mi (18 km) northwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir Wilderness adjoins the study area's western boundary (fig. 1).

Jan 1, 1983

By Robert J. Timko

Because of leakage through and around permanent stoppings in underground mines, more air must be forced into a mine than would otherwise be required for ventilation. As power costs increase, costs resulting from air leakage add increasingly to the operating costs of mining. The Bureau of Mines evaluated four different stopping construction techniques based on the ideas that (1) airtightness could be enhanced by brushing rather than troweling on mortar sealant and that (2) modified mortars (mortars containing glass fibers and other additives for increased strength and adhesion) would improve sealing performance. Air leakage tests comparing conventional to modified stoppings were done when the stoppings were built, after 6 months, after 1 yr, and following simple maintenance. It was found that stoppings can be built and maintained better if-- The area where a stopping is to be built is properly prepared. Stoppings are constructed using the techniques devised by the Bureau. Stoppings are periodically examined for leaks. Stoppings found to be leaking, especially at the perimeters, are resealed.

Jan 1, 1983

By L. C. IlsLey

The Burrell methane indicator developed by Col. G. A. Burrell in 1915 was modified during 1918 to the " insulated type " Burrell indicator . Though this instrument has been used in mines since its first introduction , it was not formally approved as safe and efficient for use in gaseous mines until March , 1922. The indicator is built by the Mine Safety Appliances Co. , Pittsburgh , Pa . Approval No. 800 has been assigned to this company covering the device in the form approved . The principle of the Burrell indicator is fairly well known . It works on the same principle as the Haldane apparatus - measuring by means of a graduated scale , the contraction resulting from burning the methane content of an air and gas sample . A given aniount of the mine atmosphere to be tested for methane is taken into the indicator . This sample is then thoroughly shaken with the water in the indicator for one minute . The methane in the sample is now burned for two minutes by a heated platinum coil , which is energized by a small storage battery containing two Edison cells connected in series . After the glower or coil has burned for two minutes , it is disconnected from the battery , and the indicator is again shaken for The amount of contraction observed by reading the height the water rises in the U- tube of the indicator , which is calibrated to register the percentage of gas in the sample . The indicator as approved by the Bureau of Mines is equipped with an Edison M- 8 mine- lamp battery , and with a glass and scale graduated from zerɔ tɔ four per cent methane . The approval of a corbination service that is , an attachment for giving illumination from the same battery from which the platinum glower is operated has been withheld pending the development of a battery with larger capacity . - Under laboratory operating conditions , a single glower was capable of making at least 20 determinations if proper precautions were observed with respect to the use of freshly charged batteries . A battery should be allowed to stand off charge several hours before using in an indicator , as the peak voltage of a freshly charged Edison cell is abnormally high and is likely to send enough current through the glower to melt the platinum wire . Fifty-seven satisfactory operations were obtained from a completely charged battery . The point where the voltage of the cell fell below 2.3 volts with the glower attached was taken as the lower limit of successful operation . A voltage less than 2.3 does not permit the lower to burn at a temperature that will completely burn the gas in the air , thus giving a false indication .

Jun 1, 1922

By Charles L. Kimbell

In 1990, the aggregate value of world international export trade in mineral commodities was estimated at more than $64 billion in current (1990) dollars, about 8.4% higher than that in 1989, but still 8.7% below the record high set in 1980. Table 8 provides a data series for the estimated value of world export trade in all mineral commodities from 1979 through 1990, as well as a breakdown of this total into fuel and nonfuel commodities. It is noteworthy that for this 1990 edition, trade data for the year of review were available in time for inclusion, whereas in previous editions, the latest available global trade data were for the year prior to the year of review. Hence, as regards trade, this edition of Minerals in the World Economy updates the 1989 edition by 2 years rather than by only 1. For this reason, it is appropriate to note that the 1989 global total value for inter-national export trade in mineral commodities was almost $596 billion, 11.1 % above the revised 1988 level of more than $536 billion, both figures expressed in current dollars for the appropriate year. Despite the considerable increase in the dollar value of mineral commodity exports, their share of total export merchandise trade declined to 19.1 % in 1990 from 19.7% in 1989. At 19.1%, this share was very near the recent year record low of 19.0% reached in 1988. The year 1990 was the fourth in a row in which the total value of world mineral commodity export trade increased.

Jan 1, 1993

"Introduction.The Bureau of Mines has taken up the problem of determining a method or methods whereby underground compensation insurance rates for metal-mining companies can be equalized in proportion to the underground hazards involved. This study has been started by the writer with the assistance of Mr. I. M. Wolfin* as consultant.The present paper briefly reviews the origin of accident compensation, gives a digest of State compensation laws, and describes types of insurance carriers. This will be followed by study of the basis of premium rate, risk differentials, and cost of compensation insurance to mine operators. These data will be supplemented by an analysis of the accident hazards in different mining methods and practices, and the severity and frequency of accidents classified by time lost and period of exposure to hazard, for different States, mining methods, occupations and nationalities. Attention will be given to standardized preventives for underground accidents in metal mines, and, finally, the classification of underground metal-mining hazard for workmen's compensation insurance premium rating."

Mar 1, 1924

By Oliver W. Keener

This paper describing the methods and costs of mining at the Hartley-Grantham mine of the Century Zinc Co. in the Tri-State Lead and Zinc district is one of a series being prepared by the United States Bureau of Mines can mining practices, methods, and costs in the various mining districts of the United States. LOCATION, HISTORY, AND GEOLOGY The Hartley-Grantham Mine is located just outside the city limits of Baxter Springs, Kans., as shown in Figure 1. A plan of the mine is given in Figure 2, and Figure is a cross section through A - A of Figure 2.

Jan 1, 1930

By John J. Henn

Two lime sinter processes for recovering alumina from clay, the double-leach process and the single-leach process, are evaluated in this Bureau of Mines report. In both processes, clay and limestone are mixed and sintered to form calcium aluminate from which alumina is extracted as sodium aluminate by leaching with a dilute solution of sodium carbonate. The pregnant liquor is desilicated, then carbonated to precipitate alumina trihydrate which is recovered and calcined to a,-alumina. The fixed capital costs for plants producing 1,000 tons per day of alumina are $85 million for the double-leach process and $86 million for the single-leach process based on a Marshall and Stevens chemical equipment index of 240.0. Because plant locations are variable with respect to the proximity of clay and limestone deposits, a nomograph is included to determine operating costs at various delivered costs of clay and limestone. For plants at which the delivered cost of clay containing 30 percent A1203 is $2 per ton and the delivered cost of limestone is $1 per ton, the operating costs are $81.04 and $89.87 per ton of alumina for the double-leach process and single-leach pro-cess, respectively.

Jan 1, 1969

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992

By O. C. Baptist

The gravitational pressure gradient (GPG) in porous sandstone containing free gas was determined to define the proper GPG to use when calculating the rate of downdip flow of oil in the Sub-Scalez No, 1 sand, Elk Hills field, Naval Petroleum Reserve 1. The GPG was determined at several gas saturations using long, artificially consolidated sandstone models that were mounted vertically in some tests and horizontally, with rotation, in others. Also determined by laboratory and field tests were relative permeabilities, capillary pressure relations; critical gas saturation, water sensitivity, and depletion drive performance. The critical gas saturation in the models having an absolute permeability of 1 to 2 darcys was about 2 percent of pore volume. The GPG with the critcal gas saturation was that due to the weight of the gas-saturated oil. The GPG in the upper part of the models was reduced as gas saturation increased to a value considerably larger than the critical. The exact gas saturation at which the GPG became less than that due to the weight of the oil could not be determined but was estimated to be of the order of 10 percent of pore volume. Tests indicate that the rate of oil production is not permanently reduced by exposure of the sand to fresh water but that the rate of injection of fresh water will be considerably less than that to brine, Methods for determining the factors mentioned above are discussed.

Jan 1, 1967

By L. W. Higley

Particulates generated in electric furnace (EF) steelmaking constitute approximately 1 to 2 pct of the charge. This flue dust is a rich source of zinc (values are substantially higher than in ore), but although there are several processes for recovering the metal, none are considered economic in the United States. This report reviews extraction technology and presents results of Bureau of Mines reduction-volatilization tests on pelletized EF dusts which achieved high recoveries of zinc. The data are sufficiently encouraging to warrant consideration of EF dusts as raw material for primary zinc smelters.

Jan 1, 1977

By Richard L. Rains

The 15,770-acre Worm Creek Roadless Study Area is in southeastern Idaho about 8 miles (mi) west of the northern portion of Bear Lake. U.S. Bureau of Mines personnel examined the roadless, area during the summer of 1984. No mineral resources were identified within the study area. There were no mines or mining claims in the study area in 1984. However, the study area is blanketed with oil and gas leases, but no known productive horizons have been identified within nor nearby. The roadless area is in the Cordilleran fold-thrust belt and is underlain by Paleozoic and Mesozoic marine strata more than 50,000 feet thick. The trace of the Paris thrust fault is 2 to 3 mi east of the study area and has an eastward displacement of about 4 to 7 mi.

Jan 1, 1985

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

8. Refuge Chambers 8.1 Refuge Chambers - Technical Discussion 8.1.1 Introduction As a part of the overall escape system, refuge chambers can provide a last resort when existing escapeways are blocked. These chambers are intended to provide both protection from toxic gases and a life supporting environment for a period of time before external rescue or further escape efforts can be carried out Escapeways may be blocked physically (due to cave-ins, etc), by fire, or by the presence of a toxic or oxygen deficient atmosphere. In the first two cases, the trapped miners would most likely await external rescue efforts, and hence the design of the chamber will have to consider the time durations that such efforts may take, It is also possible, in the second case, for fire fighting and fire protective equipment to be stored in the chamber so that miners may attempt their own escape. In the third case, it should be recognized that a compact, beltmounted 1-hour self-contained breathing apparatus has been developed(9), and that other, less compact equipment is available for up to 4 hours of self-contained breathing supply. If such equipment were stored in the chambers, then miners could escape by travelling from chamber to chamber, taking temporary refuge in each before proceeding to the next. 8.1.2 Background The concept of "barricading" has long been recommended for those emergencies where miners are trapped inby a fire. Barricading, which is the construction of a makeshift shelter in a crosscut or deadend, protects the entrapped miners from toxic gases and enables them to conserve a supply of air. In this manner, they can survive two or three days--hopefully enough time for them to be reached by rescue teams. In the past, many lives have been saved with this technique.

Jan 1, 1976

By Ann G. Kim

Gas samples containing 02, N2, H2, He, CO2, CO, CH4, and trace amounts of C 2 to C6 hydrocarbons are analyzed by a gas chromatographic method that utilizes both thermal conductivity and flame ionization detectors. A porous polymer support and molecular sieve columns are used with argon as the carrier gas. A column selector valve makes it possible to perform a complete analysis either on one 1-ml sample in 40 minutes or on two samples in 20 minutes, one sample for each detector. Samples are introduced either by on-column injection or through a gas sampling valve. By varying operational parameters, the speed, sensitivity, and accuracy of analysis may be modified to suit a particular situation.

Jan 1, 1974

By C. H. Elder, Maurice Deul

Coal degasification boreholes drilled from the surface have been success - fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

By W. J. Fullerton

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States, end deals directly with methods and costs at the quarry and mill of the North American Cement Corporation at Catskill, N. Y. The process of manufacturing cement is described only as far as the final grinding of the raw materials. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual producers, as well as to the industry as a Whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding; of the scone of the cost tabulations may ensue.

Jan 1, 1931

By G. R. Friggens

A nuclear method for continuously monitoring the coalbed and ash levels and void formation in commercial-scale, fixed-bed, pressurized gas producers is proposed. Measurement of gamma ray transmission through the coalbed is the basis of the method. The coalbed level is monitored by detecting the trans-mission of gamma rays from a 1 to 2 Ci Co-60 source positioned on the outside wall of the vessel. Coal bridging or, alternatively, ash level is monitored by a 10 Ci Co-60 source at the center of the coalbed. Source activities and geometries are calculated for a 12-foot-ID producer designed to operate at 350 psi. Source capsule and detector specifications and operational safety are also discussed.

Jan 1, 1973

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines lid some development drilling at the Milan deposit in an endeavor to find an additional source of supply of copper. The deposit, which is in Coos County, northern New Hampshire, is about 8 miles northwest of Berlin. It was discovered in the seventies and was worked steadily until 1886, yielding a monthly production of 2,600 tons of ore. Lessees opened the mine again in 1695 and mined 1,500 tons. The Milan Mining & Milling Co. acquired the property in 1907 and made regular shipments of ore and concentrates until 1910. From 1911 until 1938, the tract was held by a local resident for timber land, Ventures, Limited, a mining concern with headquarters at 25 King Street, West, Toronto, Canada, acquired the property in 1938. No production has been recorded since 1910. To cut the vein below the old mine workings and to search for extensions to the northeast and southwest, the Bureau of Mines diamond-drilled eight holes for an aggregate of 3,596.2 feet.

Jan 1, 1950

Four actual coal mine waters were used in various phases of the research program. All were from the Sewickley Creek area In Westmoreland County, Pennsylvania. The BCR designations, site locations, and nature of the mine water samples are described briefly in the following paragraphs.

Jan 1, 1971

By W. M. Weigel

Langley is about nine miles north of Augusta, Georgia., on the Sou them :l;.ilv1ay. According to the South Carolina. Geological Survey, tr.e district is known a.s tr. Horse Creek and Town Creek sub-areas of the Aileen or Savannah River Area f the South Ciil.Z'olina Coastal Plains. The geology and origin of the clays 3l"e Jscribea in a bulletin of the South Carolina Geological Survey (Series 4, Bull, l; "A Preliminary Report on Cl.:.ws of South Carolina.-), According to this report, i.he clays are sedimentary kaolins, in the Mid.dendor! and Hamburg series of the Cretaceous Age.

Aug 1, 1922

By W. L. Staker

Alternatives were developed to the conventional ammoniacal carbonate leaching-steam stripping procedure for recovering copper as an oxide from contaminated scrap metal. By entraining air bubbles in the leach solution, the copper dissolution rate was increased to 1.5 g/in2 of copper surface per hour, compared to 0.5 g/in2/hr produced by conventional agitation in stirred tanks. Using entrained nitrogen gas bubbles for agitation in conjunction with powdered sulfur not only resulted in rapid dissolution but also simultaneous precipitation of the copper from solution as a high-grade cuprous sulfide.

Jan 1, 1971