Search Documents

The latest Active List of Permissible Explosives and Blasting Devices was published in July, 1929, as Bureau of Mines Report of Investigations 2947, 2 under the title or "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1929.' Subsequent Reports of Investigations 2253, 2958, 2962, 2972, 2988, 2992 and 3000, were issued to record the official actions taken during July, August, September, October, 1929, and January, February, and March, 1930. No changes were made during November and December, 1929, and April, 1930. The following additional changes in the list recording the actions taken during May, 1930, are now authorized. [ ]

Jan 1, 1930

By David S. Yantek, Paul Jurovcik, Eric R. Bauer

Workers in coal preparation plants, where vibrating screens are significant noise sources, are often exposed to sound levels exceeding 90 dB(A). The National Institute for Occupational Safety and Health, a major coal company, and a vibrating screen manufacturer conducted a cooperative study of vibrating screen noise. Rubber isolators reduced sound levels by 1 dB. Urethane screen panels did not reduce sound levels in this case. Drive noise was determined to be the dominant noise source on the screen. Damped side plates reduced vibration levels on the screen sides by 1 to 7 dB(A). Detailed results of the study are presented.

By C. H. Elder, M. C. Irani

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand- stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By Gerrit V. R. Goodman, Fred N. Kissell, Charles D. Taylor

In This Chapter [Methane emission peaks Exhaust line curtain or duct The spray fan system Dust scrubbers with blowing ventilation Dust scrubbers with exhaust ventilation The ventilation of abnormally gassy faces Methane detection at continuous miner faces Ventilation and methane detection at bolter faces and Reducing frictional ignitions] This chapter gives guidelines for preventing methane gas explosions at continuous miner sections in coal mines, both at continuous miners and at roof bolters. The need to control peak methane emissions is particularly stressed. Emphasis is also placed on ventilation principles, monitoring for gas, and reducing frictional ignitions. METHANE EMISSION PEAKS Methane emission from the coal at continuous miner faces varies considerably. Plotted on a chart, methane emissions consist of a series of peaks and valleys corresponding to the cutting cycle of the mining machine, with the methane concentration spiking as the machine cuts into the coal (Figure 3–1) [Kissell et al. 1974]. These methane peaks can be substantial. For this reason, efforts to safely dilute the methane must focus on the level of the [ ]

Jan 6, 2006

By Charles L. Kimbell

This study is intended to serve three roles. First, it is the second annual edition of this study in a separate volume that represents a global overview and summary to supplement and complement the five regional volumes that now constitute the U.S. Bureau of Mines international, geographically arranged studies. In this regard, it also extends previous works under this title that appeared in the inter-national volume of the Minerals Year-book from the inception of that volume (the 1963 edition) until it was subdivided into six separate volumes in 1989. Following the traditional format of past chapters under this title, the basic statistical presentations herein deal chiefly with 1990, and in a few instances with 1988 or 1989; these latter two only because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting on the world's mineral industry that have occurred between the end of 1990 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

By C. J. Thompson

In the course of the work currently conducted by the Bureau of Mines in cooperation with the American Petroleum Institute Research Project 48 on identifying sulfur compounds in petroleum, a micromethod was developed (12)5 for catalytically removing the sulfur atom from sulfur compounds. The product is the residual portion of the molecule; the structure otherwise was unaltered except for hydrogenation of any unsaturated bonds that were present in the original compound. Positive identification of sulfur compounds isolated from crude oils is a difficult problem. Direct comparison of properties of the unknown with those of reference compounds is often impossible because of the limited number of reference sulfur compounds available. However, a relatively large number of pure hydrocarbons is available, and the conversion of the sulfur compound to a hydrocarbon enhances the possibility of identification. The technique also can be used to prepare microquantities of scarce hydrocarbons by hydrogenating compounds that are readily available.

Jan 1, 1962

By Paul S. Lewis

The Bureau of Mines hydrogenated coals of different rank that had been irradiated with either x-rays or gamma rays. Lignite, high-volatile A and C bituminous, and low-volatile bituminous coals were exposed to l billion roent¬gens of gamma-ray radiation; specimens of high-volatile A and C bituminous coals from other sources received 6 million roentgens of X-ray radiation. Irradiated and unirradiated control specimens of those coals were hydrogenated in autoclave experiments at (6,000-p.s.i. final pressure and 400° C. with retention times of 15, 30, or 60 minutes depending on the coal rank and catalytic treatment. Comparison of results from irradiated specimens with those from the control experiments showed that the radiation had no beneficial effect on the coal. High-volatile C bituminous coal may have been affected by radiation more than the other coals. One billion roentgens appeared to reduce the amount of coal converted to liquids and gases by about 10 pct., and 6 million roentgens reduced it by about 6 pct. then catalyzed with tin. In all other cases, the conversion of irradiated coal was either reduced by as much as 4 pct. or was essentially the sank as that obtained with unirradiated coal. Irradiation during hydrogenation nay be effective for increasing the reactivity of coal and should be investigated; further work with coals irradiated prier to hydrogenation is not recommended.

Jan 1, 1962

By M. A. Schellhardt

"INTRODUCTION The augmented demands for natural gas in many parts of the United States as a result of war have increased the need for information regarding the producing characteristics of natural-gas and gas-condensate-type wells capable of delivering large volumes of gas, as such information is important to the formulation of conservative and efficient operative and recovery practices.,For many years, the capacity of natural-gas wells to produce gas has received studied consideration by Bureau of Mines' engineers, and three reports 3/ on gaging gas-well capacities have been published. In Report of Investigations 2929, Pierce and Rawlins point out that for accurate gaging, the actual pressures at the face of the sand in the well and the relationship between such pressures and the rates of flow of gas through the sand must be determined. Their report describes a method of attacking the problem of determining the actual pressures at the sand by means of observations of pressures and volumes at the wellhead.In Report of Investigations 2930, Pierce and Rawlins explain how the fundamental relation"

Aug 1, 1944

By S. J. Pearce

"INTRODUCTION AND SUMMARYComplaints have been made regarding dust respirators that may be used in coal-mining operations. Some of these complaints may be due to improper use of the respirator, inadequate knowledge of its purpose and mode of functioning, poor choice, poor fitting, or inadequate maintenance. It is hoped that this circular will answer these complaints by discussing the various factors relating to the proper use of dust respirators in general and in coal mines in particular.It is pointed out that dust respirators are not to be used as a substitute for dust-control measures. The construction, functioning, choice, fitting, and maintenance of dust respirators are discussed.FIELD OF USEThe function of the dust respirator is to prevent the wearer from inhaling harmful quantities of dust by removing dust from the air he inhales.A dust respirator is not to be used as a permanent substitute for dust-control measures. It is to be used as a temporary substitute until dust-control measures can be instituted or as a protective means where dust-control measures are impracticable, as in applying rock dust in bituminous-coal mines.The following sections of the ""Federal Mine Safety Code for Bituminous-Coal and Lignite Mines in the United States"" 2/ emphasize the fact that every effort should be made to keep the amount of dust in the air of the working places as small as possible:"

Mar 1, 1950

By George S. Koch

A statistical analysis of silver assay data from rotary-drill-hole cut-tings and diamond-drill-hole cores from the Round Mountain prospect, Custer County, Colo., demonstrates several useful methods for estimating grades and tonnages of ore from the drilling of wide-spaced holes in disseminated deposits of precious metals. A new method of are appraisal is introduced which estimates grade and tonnage of are by calculating convex hulls (smallest convex polygons) for sample points with assay values above specified cutoff grades. Analyses of variance compare the consistency of data from rotary-and diamond-drill holes, from rotary-drill holes sampled at 2-and 4-foot intervals, from two methods of sample preparation, and from atomic-absorption and fire assaying. Evidently, data from the two types of drill holes, from holes sampled at the two intervals, and from different methods of preparation are in agreement. Atomic-absorption silver values are consistently lower than fire-assay silver values.

Jan 1, 1971

By Vijia K. Karra, John J. Sammarco, Robert Paddock, Edward F. Fries

Workers in hazardous environments such as mining are constantly exposed to the health and safety hazards of dynamic and unpredictable conditions. One approach to enable them to manage these hazards is to provide them with situational awareness: real-time data (environ-mental, physiological, and physical location data) obtained from wireless, wearable, smart sensor technologies deployed at the work area. The scope of this approach is limited to managing the hazards of the immediate work area for prevention purposes; it does not include technologies needed after a disaster. Three critical technologies emerge and converge to support this technical approach: smart-wearable sensors, wireless sensor networks, and low-power embedded computing. The major focus of this report is on smart sensors and wireless sensor networks. Wireless networks form the infrastructure to support the realization of situational awareness; therefore, there is a significant focus on wireless networks. Lastly, the “Future Research” section pulls together the three critical technologies by proposing applications that are relevant to mining. The applications are injured miner (person-down) detection; a wireless, wearable remote viewer; and an ultrawide band smart environment that enables localization and tracking of humans and resources. The smart environment could provide location data, physiological data, and communications (video, photos, graphical images, audio, and text messages).

Jan 4, 2007

By W. P. Yant, R. R. Sayers, G. W. Jones

In the treatment of any illness the early diagnosis is of very great importance . This is especially true in cases of carbon monoxide poisoning , whether acute or sub-acute in character. A diagnosis of CO poisoning is usually made from a correlation of the history , the possible place of exposure , and the symptoms produced . This , however, is not positive evidence because CO often is present in unsuspected places and can be absent in suspected places . Also , the symptoms of this type of poisoning are common to other causes . In many such cases the correct diagnosis may be very difficult , if not impossible by this method and as a result little or no treatment is given . Sub- acute cases , those in which the subject is exposed to concentration sufficient to cause only headaches , malaise , feeling of weakness and dizziness , may be incorrectly diagnosed and as a result , improperly treated . Probably the best method of diagnosis is by examination of the subject's blood . Many methods for the detection of CO in the blood have been developed , but owing to their various individual disadvantages have never come into common usage . Some of the quantitative methods are satisfactory with regard to accuracy but require elaborate and expensive apparatus , special technique and training, or are too delicate and cumbersome for field use . It is of vital importance in all industrial and domestic accidents occuring at places where CO might be suspected or where the symptoms are typical of CO poisoning that a qualitative and preferably a quantitative determination be made the extent of poisoning being of importance in deciding whether CO was the direct or contributary cause) to show the presence or absence of 0. This is indeed essential from a medical standpoint as it aids in prescribing treatment and from a legal standpoint to insure justice in the claims that are often unjustly decided for want of positive evidence.

Jun 1, 1923

By D. S. Kingery

The control of coal dust on coal tipples and cleaning plants has not been given the consideration that is afforded underground dust hazards. This apparent oversight is undoubtedly due to the general opinion that coal-dust accumulation in tipples or cleaning plants does not present the same type of hazard that it does underground. That this opinion is at least in part a fallacy has been proved many times, and the Bureau of Mines has on record many examples of explosions in tipples and cleaning plants.3/ In addition to this explosion hazard, coal dust is considered by sonic authorities to be injurious to the health of individuals exposed to it.4/ Obviously, it reduces visibility and contributes materially to accident hazards and the discomfort of the employees. Several companies have recognized this dust hazard and the advantages derived from controlling it; consequently, they have installed equipment to allay and control the dust on, their cleaning plants and tipples. The object of this paper is to. Summarize briefly some of the methods new in effect.

Jan 1, 1943

By Mark S. Sanders

The purpose of this work was to develop and field test improved knee protection for underground coal miners working in low seam mines. In a previous phase of this contract (Sanders, 1982), experimental knee pads were developed and field tested. The field test revealed several design deficiencies with the knee pads, and suggestions for improving the design were made. The work summarized in this report, therefore, consists of modifying the design and method of fabrication of the knee pads originally describes by Sanders (1982), and of field testing the improved design. The new prototype was shorter and wider than the original design, and used a neoprene pass-through strap design rather than a cloth strap molded into the pad itself. The new prototype was constructed by slush molding a hollow bladder that was then filled with foam. Initial reactions to the pads in the field test were very positive. However, after two months, the opinions about the new prototype became less positive. They were judged, generally, to be no better or worse than the pads usually worn by the field-test participants. Problems were encountered in the field with respect to durability. Water seeped into the inner cavity of many of the pads and caused the foam to deteriorate. It was concluded that it would not be cost-effective or feasible to significantly improve upon current commercially available knee pad designs.

Jan 1, 1986

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

Background. There is currently little information regarding factors associated with specific modes of motion segment failure using a fatigue failure model. Methods. Thirty-six human lumbar motion segments were fatigue tested using spinal compressive and shear loads that simulated lifting a 9 kg weight in three torso flexion angles (0, 22.5, and 45). Twenty-five segments failed via fatigue prior to the 10,000 cycle maximum. These specimens were visually inspected and dissected so that the mode(s) of failure could be determined.Failure modes included endplate fractures (classified into nine varieties), vertebral body fractures, and/or zygapophysial joint disruption. Logistic regression analyses were performed to determine whether certain morphometric variables, amount of motion segment flexion, disk degeneration scores, and/or loading characteristics were associated with the occurrence of specific failure modes. Findings. Results indicated that stellate endplate fractures were associated with increased posterior shear forces (P < 0.05) and less degenerated discs (P < 0.01). Fractures running laterally across the endplate were associated with motion segments having larger volumes (P < 0.01). Endplate depression was more common in smaller specimens (P < 0.01), as well as those experiencing increased posterior shear force (P < 0.05). Zygapophysial joint damage was more likely to occur in a neutral posture (P < 0.01).Interpretation. These results suggest that prediction of failure modes (e.g., specific endplate fracture patterns) may be possible (atleast for older specimens)

By James R. Wait

It is the purpose of this paper to review theoretical model concepts in through- the -earth transmission of electromagnetic waves. While the subject is very broad in its defined scope, we will be conscious of the specific applications to mine rescue and emergency telecommunications in coal mine environments. The plan of the paper is to outline previous theoretical efforts without attempting to attach names or organizations to the specific developments. However, we include a guide to the literature as an appendix. Without pretending to be entirely impartial we include a critique of the limitations of the available analytical models. As I see it the central problem is to calculate the steady state mutual impedance of a four-terminal network that is the black box characterizing the through-the-earth path. Problems of secondary importance include the determination of the input impedances of the two pairs of terminals and the associated transient responses. [ ]

Jan 1, 1973

By Gerald T. Homce, Michael R. Yenchek, H. Kenneth Sacks, James C. Cawley

Abstract—Overhead electric power lines present a serious electrocution hazard to personnel in a variety of industries. Overhead lines, typically uninsulated conductors supported on towers or poles, are the most common means of electric power transmission and distribution, and are exposed to contact by mobile equipment such as cranes and trucks. Equipment contacting energized overhead lines becomes elevated to a high voltage, and simultaneous contact by personnel of the “hot” frame and ground can cause serious electrical shock and burns. Industries where risk of these accidents is greatest include construction, mining, agriculture, and communications/public utilities. An estimated 2300 accidental overhead line contacts occur each year in the U.S. This paper describes a practical low-cost concept to detect actual contact of mobile equipment with a high-voltage line and provide a warning. Accident statistics indicate that more than half of the fatalities could be prevented by such a device. Index Terms—Crane, electrical shock prevention, engineering control, mining, mobile equipment, power line.

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

By A. B. Hooker, L. C. IlsLey

Several ignitions or mine pa, which might have led to explosions, and at least ona mine fire attributed to heated leg wires of electric detonators, have occm.rred. at rn1::.es in which outside shot firing is practiced. Photographs taken at one mine ind.la.ted. that the wires became red hot during firing. These results having been --i·-led. to the .Lttention of the electrical section of the Bureau of the Mines, ignitions the tests and to reportd aid in herein preventing were made future to trouble determine of if this possible kind, the cause of The investigation, which 1• considered preliminary, included tests to determine the conditions tha.t cause gas ignitions from heated. leg wires of electric and. of detonators, copper leg possible wires, remedies The tor samples such of heating, wire used. and in the the relative test were behavior the of reg\llar ironDa. Pont iron and copper leg wires (No, 22 A,W,G.) C\1t from Du. Pont electric detonators.

Aug 1, 1922

By Jan M. Mutmansky, Christopher J. Rise

"One of the most serious long term health problems associated with underground,mining is Coal Workers Pneumoconiosis (CWI'), more commonly known as Black Lung Disease. It occurs in some coal workers, normally after 15 or more years of exposure to coal mine dust, and leads to a variety of respiratory problems. Two types of pneumoconiosis are recognized simple CWP, which has been estimated to affect 6.9 percent of miners and is a condition that does not impair the miner's ability to work nor reduce life expectancy; and a more severe form of black lung (called progressive massive fibrosis) that occurs in about one percent of the cases and results in severe lung damage.Although the relationship between coal dust and CWP has long been recognized, detailed knowledge of the relationship is insufficient for setting up authoritative guidelines to reduce the health risks for those employed in dusty,underground environments. CWP is not only a health problem for workers that causes considerable distress, it is also a very expensive problem the total annual costs associated with CWP approach two billion dollars.As part of its efforts to combat CWP, the U.S. Bureau of Mines in 1983 established a Generic Mineral Technology Center to carry out basic research into all aspects of respirable coal dust:— control of dust generation — the behavior of dust in the mine — characterization of dust particles interaction of dust and lung— the relationships among dust generation and mobility and the mine environment, geology, and seam characteristics,Penn State, West Virginia University, the University of Minnesota, and the Massachusetts Institute of Technology are involved in this research, which is administered from the Department of Mineral Engineering at Penn State.Our work is one of the seven projects to be conducted at Penn Slate. We are concerned particularly with the characterization of dust and its relationships with the mine environment, and our main goal is to establish standard procedures for describing and measuring these variables.Coal DustCoal dust is a very complex material that varies greatly in chemical and mineralogical properties. Moreover, it is not the only constituent of respirable dust in the mine. When a coal seam is mined, it is inevitable that rock particles other than coal are included in the material. This rock comes from the mine roof, the floor, and the partings and inclusions within the coal scams. Since the roof and floor strata, the partings and inclusions are often stronger than the coal, mining them frequently causes more dust than mining the coal itself. One of the objectives of our research is to find the relationships between a specific coal's characteristics before it is mined and the respirable dust characteristics after it is mined. We are particularly interested in the size distribution of particles, the chemical properties, and the mineralogical properties."

Jun 1, 1988