Search Documents

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By McHenry Mosier

This paper describes come mechanical raid electrical signal systems in common use in Metal-mine shafts, together with several distinctive systems that indicate or control the origin of the signal. The latter systems remove the hazard of the movement of the cage from one level in response to signals from another. Previous publications of the Bureau of Mines have covered several meritorious installations One of the best signal systems for deep shafts is at the Homestake mine4/. A successful installation of an induction system in the Lake Superior mining region permits signaling as well as telephoning from cages at rest or in motion5/. El Potosi mine uses a variation of the three-wire electric system6/. A mine in Utah has developed a system of the double trolly-wire type, in which the cage attendant may signal from a moving cage7/. At present no system of the sine-shaft signaling employing radio is available.

Jan 1, 1939

By P. G. Clites

This study was undertaken to determine the effect of consumable-electrode vacuum arc melting on the properties of copper and to determine the applicability of the process to the production of cast shapes of copper. Ingots and castings were produced from electrolytic tough pitch copper (ASTM designation ETP), from electrolytic cathode copper (ASTM designation CATH), and from oxygen-free copper (ASTM designation OF). The products of this study were evaluated to determine the effect of the melting process on the removal of impurities from the copper and on the physical properties of the copper. The results indicate that consumable-electrode arc melting can be satisfactorily applied to the melting and casting of copper. Ingots prepared directly from electrolytic cathode copper contained slightly higher levels of impurities than are found in commercial oxygen-free copper, Excellent results were obtained with centrifugal castings of unalloyed copper, and reasonably successful static castings can be produced if proper mold and gating systems are employed.

Jan 1, 1963

By Edward D. Thimons

The Bureau of Mines conducted a state-of-the-art study of techniques currently employed to close large openings in underground mines. A large opening was considered to be any opening over 10 feet high and having a cross section of at least 200 square feet. Five salt mines and one limestone mine were visited to observe various methods of sealing large openings. Because of the variations in conditions from mine to mine, no definite conclusions could be drawn as to which is the best method. In mines where waste material is available, stoppings built by piling waste material are efficient and economical. Where waste material is not available properly constructed brattice cloth stoppings are superior to those built from wood, concrete block, or urethane foams.

Jan 1, 1975

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

By John Redington

This paper describing the milling practice at the Coniaurum Mine is one of a series of papers on milling methods, practice, and costs prepared in cooperation with an published by the United States Bureau of Mines. The 500-ton will of the Coniaurum Mines (Ltd.) is located at approximately the center of the company's property and a little more than a mile from the town of Schumacher, Ontario. The main shaft through which all the ore is heisted is adjacent to the mill so that the ore hoisted in a 3-ton skip is dumped directly into a 15-ton bin at the crusher.

Jan 1, 1931

By Forrest T. Moyer

In conjunction -with the statistical survey of the lime industr-.r in 1939, by the Bureau of Hines, producing companies reported the lime-fuel ratios attained in their plants according to type of kiln and kind of fuel. Each ratio, expressed as the number of pounds of lime burned by a unit quantity of fuel, was weighted according to the tonnage of quicklime pro- . duced at the reporting plant and grouped with similar data from other plants, so that an average ratio for each type of fuel and,kiln could be calculated. By this method the variables trat affect ratios of individual plants are more or less equalized, and the computed average lime-fuel ratios provide a fair measure of kiln and fuel efficiencies during 1939.

May 1, 1941

Heavy liquids have come into use in ore-dressing investigations, as they make possible the separation of an ore into its specific-gravity components. A paper containing a general dissertation on heavy liquids has been written by John D. Sullivan,4 and the practical application of heavy liquids is explained by Box and Crabtree5. Some heavy liquids become discolored after continued use, and the lack of transparency impairs their value. Since they are fairly expensive, reclaiming is desirable. This paper briefly discusses the preparation and care of some of the more common heavy liquids.

Jan 1, 1928

By G. W. Grove

Coal-mine officials and those who are preparing to become officials should be familiar with the instruments and devices that are employed rather commonly in and around mines and should know how to use them with safety and efficiency. Among these axe instruments and devices used in determining the pressure, velocity, volume, and certain other conditions of ventilation and in detecting the more common mine gases, such as methane, carbon monoxide, and hydrogen sulphide, or a deficiency of that very important agent, oxygen. Water gages, anemometers, barometers, psychrometers, flame safety lamps, lamp-testing boxes, and methane, carbon monoxide, and hydrogen sulphide detectors are described and their use and operation discussed in this paper.

Jan 1, 1938

By Lowell B. Moon

Regardless of how a mineral deposit in first discovered or by whom, any mining enterprise based upon it must pass through a preliminary stage of exploration. The common understanding of ?exploration? among mining engineers is well-expressed by Jackson and Knaebel:3/ Exploration work ranges from that performed by the individual prospector employing only the simplest tool, and equipment to elaborate campaigns involving the expenditure of largo stuns of money end the use of churn- car diamond-drilling equipment, large test-pitting crews, or sometimes a regular mining organization. In any event, the object is to determine as accurately as possible, with the funds available, the size, shape, and other characteristics of the ore bodies and their average value or grade.

Jan 1, 1945

By L. C. IlsLey

"According to accident statistics, issued from time to time by the Department of the Interior, Bureau of Mines covering fatalities in coal mines, between the years 1870 and 1921 there were 4,897 deaths caused by explosives. The legislatures and safety commissions of the various mining States have Elected and formulated many excellent regulations in regard to the handling and use of explosives in an endeavor to keep this class of accidents as low as possible. An analysis or comparison of the explosive, regulations issued by over thirty States would make a very long paper, however, by subdividing according to phases and issuing several papers it is believed that the material will be more readily available. The first phase was treated in Serial No. 2405 of the Bureau of Mines (""State and Federal Electrical Shot-Firing Regulations,"" issued in October 1922) which gave a compilation of such regulations as apply strictly to electric shot-firing. The second phase under consideration is ""Who may set off blasts in coal mines.""In some States, the person who does the firing must be an ""authorized shotfirer,"" while in other States he must have proved his ability to do this work, and again in other States he is ""any person."" The present paper covers rules and regulations relating to this phase of shotfiring, and those States having similar regulations have been grouped as follows."

Jun 1, 1923

By Walter T. Ackley

[The geophone has occupied a prominent position as a mine signalling device since its first introduction. The Bureau has carried out tests at different times with a view to improving the early geophones. The following paper describes briefly the adaption of the vacuum-tube audio frequency Amplifier to a new form of geophone. It is not intended to convey the idea that the results described are sufficient to warrant the drawing of definite conclusions as to the practicability of the electrical geophone, but the data and tests liven herein are made public because of their possible use to the industry and as a result of inquiries received as to the feasibility of such adaptions and modifications of the early geophones. Because of the limited time available to the authors, only one geophone with its auxiliary amplifier was constructed. As is well known, two geophones are necessary in order to determine the direction of a sound. Although the principles upon which the electrical geophone operates appear to be fundamentally correct, it is not possible to state whether two such devices 'rill function as efficiently, (as regards determining direction of sound) as the present geophone. In order to operate efficiently as a direction finder, the amplifiers of the electrical geophone must each amplify with exactly the same degree of magnitude. By proper design and adjustment this can probably be accomplished without greatly complicating the design. inasmuch as audio frequency amplification is used, no tuning; is necessary as is the case with tuned radio-frequency circuits. The same filament and plate batteries can be used to operate the amplifiers and by the use of dry cell tubes, requiring shall filament and plate currents, it if believed that a compact, portable and practical instrument can be evolved. Further investigations of the electrical geophone should be conducted to determine the points outlined in this preliminary report.]

Jan 1, 1924

By E. D. Gardner

"Introduction Ore from stopes in metal mines is generally dumped or drawn into chutes or raises through which it passes by gravity to the haulage levels. Occasionally, and under some conditions quite frequently, the ore in a chute will wedge or hang and refuse to run. This hanging of the ore may be due to the packing of damp or clayey material, to boulders forming an arch, or to loose lagging or other timber becoming lodged in the chute.In drawing material from a loading chute it is drawn out a car at a time, and the intermittent flow of the material .increases its tendency to hang. When the obstruction in the chute is near or at the loading gate, the chute pullers start the ore by punching it with iron bars inserted through openings in the chute gate. When the obstruction is beyond reach of the bars, other means of starting the ore must be used.In some systems of mining, chutes or ore raises are built with timber as the stope extends upward. Generally, a manway is left alongside of the chutes, and when the ore hangs in a chute usually it can be started by a miner from the manway ladder by pounding on the timbers of the chute or by punching the ore with a bar inserted through small holes in the chute lining. Special methods of starting clogged ore, such as shaking a chain left hanging in the chute, are used at some places.In other systems of mining, ore passes or chutes are run through solid rock and when the ore hangs in one of these passes, either it must be blasted or else started from the top. Sometimes the ore can be started by running water into the top of the chute, but if the water does not start the ore moving, it must be blasted from underneath. This is done by detonating a bundle of cartridges under the obstruction in the chute or raise."

Jan 1, 1927

By Oliver A. Dibble

This paper it one of a series being prepared for and published by the United States Bureau of Mines, describing mining methods and costs at clay pits throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The open-pit recovery of clay for cement plants is a comparatively simple operation in comparison with underground mining of clays; nevertheless, it represents an appreciable factor in the cost of cement manufacture. The following report deals specifically with the methods employed by the Aetna Portland Cement Co., which operates cement mills at Fenton and Bay City, Mich., in recovering clay from their pit at Corunna, Mich., on the Grand Trunk Western Railway.

Jan 1, 1932

By Jr. Herty

Ferromanganese continues to be an indispensable requirement in steel manufacture. Approximately 470,000 of the 80 per cent ferro-alloy was consumed in 1929 and increasing amounts will be required annually by the steel industry unless some satisfactory substitute is found. An average of 14 pounds of metallic manganese is used for each ton of steel produced, The principal use of manganese is for de-oxidation of the metal in the steel refining processes, although a considerable amount is also used for the production of special manganese steels. Unfortunately, domestic production of manganese ore is inadequate to meet normal peace-time requirements, not to mention increased abnormal war-time demands. The rather large quantities of low-grade manganiferous iron ores which occur in the Coruna Range in Minnesota have for a number of years greatly appealed to those interested in the development of a domestic source of the supply. The North Central Experiment station of the Bureau of Mines has made an elaborate study of the possibilities of the pyrometallurgical treatment of ores from these deposits and much of the valuable information secured by them has already been published.

Jan 1, 1930

By W. R. Wrzensinski

This report presents the findings from a l-yr Bureau of Mines program in which sulfur concrete reinforcing materials were tested and evaluated to determine their resistance to corrosion. It also summarizes the permeation characteristics of sulfur concrete and the exemplary performance of precast, reinforced sulfur concrete structures in various industrial environments. The Bureau is furthering the development of sulfur concrete technology as part of a larger effort to find uses for the Nation's plentiful sulfur resources in construction materials. Sulfur concrete is a corrosion-resistant material that can be used in acid and salt environ-ments where conventional materials fail. Penetration of corrosion-inducing agents is minimized because of the low permeation characteristics of sulfur concrete.

Jan 1, 1988

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

CALCULATION OF MINE HEAD LOSSES FROM ALTIMETER SURVEY DATA USBM PENNSYLVANIA STATE UNIVERSITY - MINERAL ENGINEERING DEPARTMENT USBM USBM USBM THIS PROGRAM CALCULATES PRESSURE LOSSES USING THE USBM METHOD GIVEN USBM IN USBH IC 7809 BY MCELROY AND KINGERY.1957. THE MAJOR DIFFERENCE USBM BETWEEN THIS PROGRAM AND THE CITED REFERENCE IS THE TREATMENT OF AIR USBM

Jan 1, 1977

By Kenneth M. Earl

In its program of investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the Tapley deposit in an endeavor to find an additional source of copper. There are accounts that many years ago the property had some production; there are several old, inaccessible shafts apparently sunk on a vein in rhyolite or diabase. The waste dumps of these shafts contain considerable sulfides, chiefly pyrite and chalcopyrite. To cut the vein below the old mine workings, the Bureau of Mines? diamond-drilled five holes aggregating 1,204 feet. No significant copper mineralization was found.

Jan 1, 1950

By J. B. Littlefield

This study is one of at number conducted to determine the concentration of dust in the air during the complete cycle of operation in wet drilling; information as to various factors connected with, drilling in mining operations is considered to be of definite value in the control and prevention of air dustiness, and it in particularly desirable to ascertain whet features of present-day wet-drilling operations in mine work contribute to dust disease and to remedy deficiencies when they are found.

Jan 1, 1938

By H. C. Loesche

The problem of signaling to the hoisting engineer from the cage in a shaft mine has been given considerable thought and attention by engineers and mine operators seeking to Increase the safety and efficiency of hoisting. HISTORY R. L. Rutherford,3/ an employee of the Magma Copper Co., Superior Ariz., realizing the need for a simple and practical moving-cage signaling system, began a serious of experiments early in 1937, Available electrical moving-cage signal in operation at this date required that signal wires be installed in the shaft to make a simple, positive signal without wires, the first experiments used the pipe lines in the shaft for carrying the signal current, but these experiments were not successful.

Jan 1, 1945