Search Documents

By N. Hanief

This research involves the investigation of phase transformations in the platinum-chromium coated system. Single-layer 0.1 µm platinum coatings were deposited via electron beam deposition on 99.98 percent pure chromium substrates. Specimens were subjected to systematic heat treatment in a vacuum furnace at 900°C for up to 20 hours. Phase formation and the changes in surface morphology were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM).Both CrPt and Cr3Pt phases are formed during heat treatment for different times at 900°C. Significant changes in the morphology of this coated system were detected after heat treatment at 900°C for 20 hours.

Jan 1, 2012

Measurements of the rates of penetration at various throttle air pressures are presented as a function of thrust for three different rockdrills when drilling quartzites with strengths of 45 000 lb/in2 and 39 000 lb/in2, The rate of penetration at optimum thrust is shown to agree well with the predictions of theory and curves of air consumption as a function of throttle air pressure are presented. Man-held machines are shown to be under-thrusted at throttle air pressures above 40 lb/in2g. Measurements of bit wear as a function of distance drilled are presented graphically and discussed in terms of the theory developed in Part 1.

By J. H. Zietsman, W. J. Leipoldt

"To be able to responsibly develop a multiphysics model of the steel belt sintering (SBS) process used to sinter chromite fines, it is important to have a comprehensive understanding of the process. This understanding was gained through a site visit, observation of the process in operation, and interaction with the operators. Material characterization will also reveal much about the process that is not yet fully understood. A well-defined and representative mass and energy balance will also give valuable insight into the process. The plan for the multiphysics model aims to combine a computational fluid dynamics (CFD) model with a discrete element method (DEM) model.To obtain a more accurate mass and energy balance representation of the SBS process, it was decided to develop a dynamic distributed parameter model of the mass and energy balance. This model will be used to gain better understanding of the SBS process so that a more complicated multiphysics model can be developed later. The reason for this is because the SBS process is very dynamic, with a large temperature distribution throughout the length of the process. In its current state, the mass and energy balance model is capable of handling solid and gas material packages and exchanging heat between these packages where they are mixed, and is able to model the heating of the gas by burning CO gas. The next step in the development of the model will involve enabling it to handle evaporatoin of liquid water, burning of solid carbon in the pellets, reduction of iron oxide in the pellets with the CO gas formed from carbon combustion, and then oxidation of the reduced iron in the oxygen-rich cooling zones."

Jan 1, 2014

By I. Zh. Bunin, M. V. Ryazantseva, V. A. Chanturiya

The paper proposes a new method for selective calciferous separation. The effect was achieved through the application of the combination of high-power electromagnetic pulses (HPEMP) and a specific reagent regime of the flotation. The combined application of HPEMP with the special reagent regime allowed for the improvement of the scheelite floatability: the recovery of CaWO4 rises from 41.2 % (untreated sample) to 58.5 (sample treated at 103 pulses). In contrast, the floatability of calcite decreases significantly: the recovery of calcite drops from 74.7% (untreated sample) to 41.1 % (sample treated at 103 pulses). The conditions were found for the selective separation of the minerals with very close flotation properties. Keywords: Calcite, scheelite, flotation, high-power electromagnetic pulses, DRIFT, XPS

Jan 1, 2020

By C. Yu, N. Topliffe, H. Song, W. Yu

The water separation pump is a highly effective alternative for medium pressure (1.6?6.4 MPa) slurry pumping requirements and has been widely used in industry since it was invented in the 1980s. The water separation pump is powered by a single or multi-stage clean water centrifugal pump. The water separation pump combines the advantage of high flow centrifugal pumps with the high pressure capability of reciprocating pumps. The clean water pressure is exchanged to slurry kinetic energy through the separating chamber, the principle component of the water diaphragm pump. Currently in its the third generation, the separation chamber uses a ball and flexible water seat that provides a true separation mechanism and can completely isolate the two fluids with near zero water loss.

Jan 1, 2007

By Mike Rogers

Platinum production in Southern Africa amounted to 80% of world production in 2005with a small increase from 5 117 000 ounces to 5 275 000 ounces. For the seventh consecutive year the platinum market is on course to record a moderate deficit in supply. This is reflected in the price increase from a trading range US$860 to US$880 in June 2005 to an excess of US$1 200 in September 2006. Southern Africa, with its extensive platinum reserves, will continue to be the dominant platinum producer and has a number of new mines in an advanced stage of planning. The slogan ?Platinum Surges Ahead? was selected to describe the exciting and vibrantnature of all aspects of platinum mining, beneficiation and marketing. This conference will cover these aspects from exploration and orebody delineation, through mine design, development and operation to mine closure; mineral beneficiation, marketing and compliance with the Mining Charter will also be subjects for discussion and debate. It is also anticipated that the issue of overall increases in productivity, through the introduction of technology, will demonstrate Southern Africa?s status as a premier mining district. It is my pleasure to welcome delegates from abroad and locally, on behalf of the SAIMM, to the Second International Platinum Conference ?Platinum Surges Ahead?. I trust that you will find the proceedings informative and value adding and will participate in the discussions and debate in order to obtain maximum benefit from the conference. I am sure that the post-conference tours will be interesting and of great benefit to participants. Finally, a big word of thanks to the members of the Organising Committee, the management and staff of the SAIMM, and to our willing sponsors, without all of whom this conference would not have been possible.

Jan 1, 2006

By H. M. Wells

The influence of economics on the design of mine shaft systems by H, M. WEI.LS, Pr. Eng., M.Se. (Fellow) The purpose of this paper is to review some of the more important economic criteria that must be taken into account when planning the number, type, size, and distribution of the shafts, or shaft systems, required to exploit a block of payable ore. The postulated philosophy governing the selection of design parameters is that of optimization of the financial return per rand of venture capital employed for the project as a whole. While this criterion may not necessarily satisfy the investment objective under all circumstances (as, for instance, where risk limitation is important), it does serve to place the relative economic advantages and disadvantages of specific design features, which may sometimes be in opposition, into correct perspective with respect to the overall economics of the project under the prevailing economic climate at the time of the investigation.

By C. Tokoro, T. Kato

The objective of this study is to improve the shrinking core model for particles with a particle size distribution and clarify the activation mechanism of rare earth elements dissolution by mechanochemical activation. To achieve this objective, the method, called the doubly integrated micromodel, was applied for a shrinking core model in this study. This method consists of integrating the batch leaching rate of a single particle over the distribution of both feed particle size and reactor residence time to arrive at the fraction unleached. The usefulness of the shrinking core model improved by doubly integrated micromodel was confirmed by comparing it with a shrinking core model. To apply the shrinking core model improved by doubly integrated micromodel to rare earth elements dissolution from weathered residual rare earth ores by mechanochemical activation, leaching experiments were performed for grinding samples by planetary ball milling. The reaction equation of mechanochemical reaction by planetary ball milling for weathered residual rare earth ores was investigated by x-ray absorption fine structure analysis. As a result of a kinetics study, the rate-determining process of leaching changed from reaction to diffusion reaction control by planetary ball milling. Based on these results, it was revealed that the main mechanism of activated rare earth elements dissolution from weathered residual rare earth ores was a mechanochemical reaction by planetary ball milling. Keywords: Mechanochemical reaction, particle size distribution, shrinking core model

Jan 1, 2020

By J. D. Stone, I. D. Brumby, J. D. Inch, C. J. Beukes

A. Continuous miners, and their operation at Bosjesspruit Colliery J. D. INCH*, B.Sc. (Min.), M. I. Min. E. (Visitor) A brief description is given of the main types of continuous miner and their incidence of application in South Africa. Definitions and descriptions of the design parameters and components of the main cutting head are given. together with an outline of the modifications carried out to improve machine cutting performance. An account is given of experience with the application of water infusion to suppress airborne dust during continuous-miner operations. B. The selection and performance of continuous miners at Matla Coal by J. D. STONE, B.Sc. Eng. (Min.,) M.B.L. (Graduate) The reasons for the choice of continuous miners for the development of accesses and the winning of coal in a modern underground coal mine are discussed. It is shown that, at relatively low depths, the extraction rate as well as the costs are more favourable than those of proved total extraction methods. The selection of a continuous miner is largely dictated by factors such as production rate, capital and running costs, imported content and the extent to which local content and manufacturing are to be increased, manpower requirements, seam thickness, expected floor and roof conditions, and maximum cutting height. The present inherent shortcomings of continuous miners, such as inefficient continuous transportation of coal away from the miner and the lack of an infinitely variable traction to match the sumping speed with the feasible penetration speed, are pointed out. Specific problems encountered and the methods of solving them, as well as a planned trial with a heavy-duty continuous miner, are discussed. C. Continuous mining within the Tavistock Group of collieries I. D. BRUMBY.Dip. Min. (Visitor) The Tavistock Group of collieries is situated some 25 km south of Witbank. The three collieries comprising the Group are Tavistock Colliery, Phoenix Colliery, and South Witbank Coal Mines. Continuous mining is practised to some degree at all three collieries. This system of mining was introduced at Phoenix during 1976, South Witbank during 1978, and Tavistock during 1979. For the twelve months ended June 1979, continuous mining accounted for 1,7 Mt of the 4,5 Mt hauled from underground. All the continuous miners introduced to date have been of the rotary-drum type. D. Pillar extraction at Usutu Collieries using continuous miners by c. J. BEUKES(Visitor) In 1969 Usutu Collieries began pillar extraction with conventional mechanized equipment. This was very successful, but certain disadvantages could be eliminated if continuous miners were used instead. In 1976 the first continuous miner was introduced for this purpose; this proved so successful that a second unit was introduced in 1977, and pillar extraction by conventional equipment was discontinued. By the end of 1978, 1,3 Mt had been mined from pillar extraction by continuous miners. This paper describes the method in some detail, and indicates that the operational costs are lower than for conventional bord-and-pillar mining. Defect solid state A one-day multidisciplinary symposium entitled 'The Defect Solid State '80' will be held under the auspices of the Solid State Physics and Materials Science Subcommittee of the South African Institute of Physics at the University of the Witwatersrand on Monday, 14th July, 1980, following the Twenty-fifth Annual Conference of the South African Institute of Physics.

Jan 1, 1980

By J. W. Neale

Mintek was a leading participant in the BioMinE project between 2004 and 2008. This project, which was funded in part by the European Commission, was aimed at the development of biotechnology for the minerals industry in Europe. Mintek?s research programme focused mainly on the development of integrated bioleach-based processes for the recovery of base metals from complex, low-grade sulphide concentrates. Specific European mineral resources were targeted and used in integrated piloting campaigns involving bioleaching, solution purification, and metals recovery. This paper describes the use of thermophilic bioleaching for the recovery of nickel and copper from a low-grade nickel-copper concentrate produced at the Aguablanca Mine in southern Spain. Currently, the Aguablanca Mine produces a bulk nickel-copper concentrate for sale to a smelter, and the proposition is to increase the profitability of the operation by the on-site production of metal or metal intermediate. Initially, bench-scale bioleach tests were conducted to determine the bioleach operating conditions. These tests included an evaluation of mesophilic, moderately thermophilic and thermophilic microorganisms. In order to achieve sufficiently high levels of both copper and nickel extraction, a thermophilic process was selected?this was necessary for leaching of the refractory chalcopyrite that occurs in this concentrate. Additional bench-scale test work was carried out to derive a conceptual process flowsheet for the solution purification and metals recovery circuit. The results of the bench-scale tests were used to design, construct and commission an integrated pilot plant, which was subsequently operated at Mintek for over seven months. During this time, the solution purification and metals recovery processes were optimized, and all recycle loops were closed. The final process flowsheet included the following unit operations: concentrate regrinding, thermophilic bioleaching at 70°C, primary iron removal using limestone, copper solvent extraction and electrowinning, secondary iron removal, nickel hydroxide precipitation using magnesia, and final solution purification using lime. Where applicable, process solutions were recycled to preserve water. The process design data derived from this pilot-plant campaign formed the basis for a conceptual engineering study for the developed process. In the study, mass and energy balances were derived, and a process flowsheet was developed and used as the basis for estimating the capital and operating costs of the process. This enabled a preliminary economic analysis of the process to be undertaken. The findings of this study are discussed.

Jan 1, 2009

By E. Dadzie

This paper will review some methods used to manage geotechnical risk at Damang Pit Cutback. The pit depth is designed up to 250m with push back on the eastern and western walls of the existed and depleted Railway Cutback (RCB) pit. The geotechnical design was presented by SRK Perth, focussing on the optimisation of the bench face angle which finally evolved with ?steep slope strategy?; 24m at 800 and 24m at 750 on the eastern and western walls respectively. The east wall was designed strategically to optimise the proximity of the tailings dam to the final pit crest of the push back. The pit has experienced failure in the weathered profile transgressing through the transitional material into the fresh rock at different location of the east wall since development in July 2005. To ensure stability and to minimise ore loss, the east wall has been redesigned using 700 batter angles and reduced berm width of 4m compared to 800 and 8.5 berm width of 24m bench height. The paper will also discuss how slope failures to the east wall had been sustained, managed and monitored to enhance production. Emphasis is placed on slope management at Damang which includes the principles of wall control blast, visual inspection, slope depressurisation and the state-of-the art of slope monitoring using Autoslope automated prism monitoring. Future slope monitoring is considering the use of 3D Laser and Radar to provide early warning so that evacuation could be effected. The intension is to provide mine personnel the means to identify risk areas during mining activities.

Jan 1, 2008

By Maggi Loubser

"In a technologically advanced era, where process control is accurately maintained within the smallest error margins, and accuracy and precision are continuously improved, sampling is still left to the lowest paid employee in the company without training him or her properly to understand the relevance and importance of the task. In this paper the objectives of sampling in a process control environment is discussed and an attempt is made to link it to the theory of sampling. Some of the practical problems associated with implementing theoretical sampling principles in an industrial environment will be elucidated and some examples given on how compromises are made. Different methods of sampling will be discussed with real life examples from different manufacturing industries."

Jan 1, 2014

By D. Fourie

A brief history of channel sampling in South African gold mines is followed by a chronicle of different sampling events and sampling methods that used the traditional ?hammer and chisel? approach as well as diamond core extraction of the sample. The problems associated with each method of sample collection are documented and the use of a laser scanner to measure the exact volumes of sample material extracted from a correctly delimited sample site are considered. Areas where increment delimitation errors (IDEs), increment extraction errors (IEEs), increment weighting errors (IWEs), and increment preparation errors (IPEs) occur were investigated. A ?simulated chip sample model? is introduced and provides the basis for comparing the percentages of error introduced as a result of improper sampling. The heterogeneity experiment showed that reefs that are more homogenous tend have lower extraction errors than the more complex carbon-rich reefs, which may contribute to understanding the poor mine call factor on mines exploiting the latter types of reef. Keywords channel sampling, chip sampling, error, bias, modelling.

Jan 1, 2014

By G-L. Wu, X-B. Liu, C-Y. Zhou

"The static recrystallization behaviour of Ti-Nb microalloyed high-strength steel during hot deformation was studied by conducting double-hit hot compression experiments using a Gleeble-3500 thermomechanical simulator. The effects of deformation temperature, strain rate, strain, and initial austenite grain size on the static recrystallization fraction are discussed. The static recrystallization kinetics were modelled, and the results show that the static recrystallization fraction increased with deformation temperature, strain rate, and strain and interpass time. The static recrystallization activation energy Qs was 326.05 kJ mol-1. Comparison of the experimental results and predicted results indicates that the effects of deformation parameters on the static recrystallization in multistage hot deformation are significant. The predicted results are in good agreement with the experimental results. IntroductionIn hot-forming processes, complex microstructures are often induced by multiple hot deformation mechanisms (Zhang et al., 2014; Liang et al., 2015). The softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by the corresponding microstructural evolution (Wu et al., 2010). It is well known that dynamic recrystallization (DRX); metadynamic recrystallization (MDRX), which occurs by the growth of DRX nuclei during intervals of deformation; and static recrystallization (SRX), which occurs by nucleation and growth during the intervals of deformation, can significantly alter the austenite grain size (Chen et al., 2015. Chen, Sui, and Cui, 2014; Mao et al., 2014). The long interpass times allow complete SRX to take place if the steel is being rolled above the interpass recrystallization stop temperature (Tnr), i.e. in the absence of carbonitride precipitation (Siciliano, 2000). In recent research, microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient in achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Bandyopadhyay et al., 2011). The alloying elements Nb, V, Ti are widely used in high-strength low-alloy (HSLA) steel to achieve the desired strength and toughness properties with solid-solution strengthening, precipitation hardening, grain refinement, and dislocation strengthening (Opiela, 2014; Chen and Yu, 2012). The wide applicability of alloying elements in HSLA steel is due to the fact that heat treatments are not required after forming of the parts, which results in time and cost savings."

Jan 1, 2017

By A. Ndibalema

Blasting is one of the primary functions in any mining operation. Despite the fact that it generally constitutes between 30% to 40% of the mining cost, blasting also affects the cost-effectiveness of down steam activities such as load and haul, safety, tyre life for haul trucks, crushing and milling. Over the past three decades, significant progress has been made in the development of new technology in an attempt to reduce costs and increase efficiencies and productivities of blasting activities. Mine to mill project concepts have paved the way for such developments. Other advancements have included sophisticated computer modelling technologies for blast design and performance analysis. There are many factors that affect the cost of blasting. These can be divided into two categories; controllable and uncontrollable. The latter includes costs related to depreciation, exchange rates and government legislation with the former category including contractor versus owner blasting costs, efficiency and productivity issues and product quality. Controllable factors have one common denominator which can determine their outcome; direct site management influence. Excavator digging rates and final floor conditions give a good measure of blasting performance, and alternatively cost effectiveness. This paper is aimed at benchmarking against a blast optimisation database, understanding the relationship between costs and identifying opportunities for improvement. Understanding the cost drivers allowed a typical cost model to be developed for the current mining operation at Geita and this was used to drive continuous improvement with emphasis on closing the information loop.

Jan 1, 2008

By H. Karabulut, S. Gündüz, K. Karacif, M. A. Erden

The corrosion properties of iron-based composite materials containing graphite and silicon carbide (SiC) reinforcement were investigated. The effects of silicon carbide reinforcement were investigated by adding 0.5% graphite and 1%, 2%, and 4% SiC. A powder metallurgy method was used to produce the composite samples. Iron, graphite, and silicon carbide powders were blended for one hour with a threeaxis mixer and then unidirectionally pressed under a pressure of 750 MPa. After pressing, the composite materials were sintered at 1100°C for one hour. The corrosion properties and microstructure, density, and hardness properties of the composite materials that can affect the corrosion properties were also investigated. It was determined that the pore ratio and hardness of the composite material increased, and corrosion resistance decreased, with increasing silicon carbide content.

Jun 2, 2022

By M. E. C. Snyman, N. Naudé

"Coal fines produced during processing are difficult to dewater and result in a lower quality product and consequent lower value. A South African coal mine experiences severe difficulties with belt filter dewatering operations due to the presence of fines reporting from the thickener underflows. Plant 2 currently handles super-fine particles of size -34 µm and has low belt filter efficiency: excessive moisture retention lowers the product quality and strains downstream processing. It was necessary to determine an alternative method for dewatering these fines. Blending of fine material with coarser material was proposed as a solution. The effect of coal particle size and layering during ultrafines belt filter dewatering was evaluated using various blends of the fine Plant 2 material with coarser Plant 1 material. The best layering arrangement of the two materials and its optimum blend required to achieve reduced filter cake moisture content was determined in practise using a vacuum filter to simulate belt filtration. A blend of the two materials gave improved dewatering efficiency for the belt filters compared with that of the Plant 2 material alone. The best layering configuration was with Plant 2 material at the bottom and Plant 1 material on top. The optimum blend for industrial applications comprised 48% fines from Plant 2. IntroductionFines are produced during the processing of coal. It is estimated that 2 to 3% of run-ofmine coal reports to the ultrafine portion (-100 µm) (le Roux, 2005). The particle size of coal is inversely proportional to the amount of water adsorption, so smaller particles adsorb more moisture. Moisture removal requires either mechanical processes or thermal drying: mechanical processes are less expensive, but the fines still have high moisture retention. Discarding of fines leads to economic losses, so it is essential that they be dewatered so that they can then be sold as a product: fines need to be treated for both resource management and conservation reasons (Kenney, 1994). Removal of free surface moisture from ultrafine coal particles using a belt filter therefore remains a process that needs to be continuously improved. Ultrafine coal originating from a thickener underflow is known to be difficult to dewater owing to factors such as filter cloth blockage and moisture retention due to clogging. Mixing of finer and coarser materials has been proposed to deliver better dewatering efficiency and improved the quality of the recycled water (Kenney, 1994)."

Mar 1, 2019

By H. M. Wells

The investment decision under uncertainty by H. M. WELLS, Pr. Eng., M.Se. (Fellow) The future outcome of a proposed investment is uncertain at the time the decision must be made to accept it or reject it. This uncertainty can be expressed in the form of a probability distribution. An attempt is made to rationalize the investment decision under these circumstances, especially when the range of possible outcomes extends into both the acceptable and unacceptable domains. A rigorous definition of risk is proposed, and a criterion of risk aversion is developed that forms the boundary between acceptable risk and unacceptable risk (called the loss limitation line). It is shown that this decision criterion can also serve as a quantitative yardstick in the evaluation of various possibilities for 'tailoring' the proposal to mlke it more compatible with the particular financial circumstances of the company concerned.

Jan 4, 1976

By I. Beukes, H. Kotze, B. Krause, R. P. Hattingh

Hillendale Mine is operated by Exxaro KZN Sands, and is situated on the north coast of KwaZulu-Natal in South Africa near the towns of Empangeni and Richards Bay, some 200 km north of Durban. During the mining operation the heavy minerals rutile, ilmenite, zircon and leucoxene are extracted for further beneficiation at a processing complex near the town of Empangeni. The deposit contains approximately 25% slimes (defined as the sub-45 micron fraction), and is mined using hydraulic monitoring. Run of mine is gravity fed down launders to pump stations, which deliver the material to a primary wet plant. Slimes is separated from the run of mine prior to the heavy minerals being separated from the sand. Sand tails containing approximately 2-5% slimes is pumped to the mining void. The slimes is thickened to a density of approximately 1.2, and most of the resultant material is pumped to a sub-aerial deposition site (residue dam). The area is characterized by an annual rainfall of approximately 1300 mm, which is relatively high by South African standards. From an agricultural perspective the soils are deep and well weathered. Dryland agriculture has been practised on an extensive scale in the area for the past 70 years. Sugar cane in particular is cultivated on and around the mine area. In terms of environmental approvals, the post-mining land use and objectives are defined as economically viable and sustainable sugar cane cultivation in the mined areas. During mining the soil profile is destroyed. In this paper the establishment of a reconstituted soil profile is discussed, with specific reference to the methodology that is being followed to achieve the homogeneous blending of sand and slimes. Defining the rehabilitation strategy and soil specification Strategically Exxaro KZN Sands divided rehabilitation into four aspects, comprising physical rehabilitation (restoration of soil structure), vegetative rehabilitation (restoration of vegetative cover), ecological rehabilitation (restoration of sustainable ecological communities), and sustainability (sustainable man/environment interface) (Hattingh and Viljoen, 2006). It is believed that the key to successful rehabilitation lies in achieving a substrate (soil) suitable for the establishment of the target vegetation. During the development of the rehabilitation strategy the key factor in the establishment of a suitable soil profile was shown to be the soil water retention of this material. Since dryland agriculture is practised, this aspect becomes critically important in ensuring that the post-mining land use is sustainable (Hattingh et al., in prep.). From a financial perspective, a closure certificate being issued implies that the state takes over financial liability for the rehabilitated land. This has significant implications for the state-the default position will be that all possible latent and residual impacts must be identified and known prior to a closure certificate being issued. From the mine's perspective this precautionary approach by the state implies that post-operational costs cannot be quantified exactly, and our approach is therefore to mitigate the risk of a long post-closure care and maintenance phase by means of addressing all potential latent defects during the operational rehabilitation phase. The financial viability of the soil reconstitution process itself is therefore not measured against other rehabilitation methods, but against the risk of not achieving closure. During a series of technical workshops comprising experts in the various disciplines in the rehabilitation of the soil profile were identified. These aspects include the re-establishment of a functional soil profile, soil physical characteristics, soil chemistry, soil biota, salinization potential, erodibility and soil weathering. The natural soils in the Hillendale area have been classified in terms of the South African soil classification system (MacVicar and co-workers, 1991) and consist of Hutton (orthic topsoils on red apedal subsoils) and Clovelly (orthic top soils on yellow apedal subsoils) soil forms. The topsoils consistently comprise medium to fine grained sand overlying heavier textured sandy clay loam to clayey subsoils. The topsoil structure consists of a single grain structure, whereas subsoils are apedal. These soils are typically deeply weathered and do not show secondary structures. During the mining process a layer of topsoil (300 mm) is stripped off, and the balance of the material down to the footwall is processed. Sand with 2-5% slimes (defined as the sub-45 micron fraction) is returned as backfill in order to re-establish the dune to approximate the previous landform. From an agricultural perspective this material is not suitable for the dryland cultivation of sugar cane. A capping of more suitable material therefore has to be provided. The most significant difference between the premining soil form and the backfill material is the percentage slimes, consequently a mixture of the sand and slimes is required as a capping over the backfilled sand. The required thickness of the cap is a function of specifically plant growth requirements, erodibility, weathering and runoff (Hattingh, et al.; in prep.). The percentage slimes required in the cap is a function of mainly soil water requirements (Hattingh and Viljoen, 2006). The conservative indications to date show that the reconstituted soil profile should consist of a homogeneously blended mixture of 70%-80% sand and 30%-20% slimes up to a maximum of 2 metres thick. This will be sufficient to ensure growth during dry periods.

Jan 1, 2007

By M. R. MacIver, M. Pawlik, H. Alizadeh

Treatment of tailings is an integral component of mineral processing. Tailings with a high clay content are a challenge for the mineral processing industry; e.g. the clay slimes produced from production of phosphate in the mid-western United States and the fine tailings produced from oil sands production in western Canada. Dispersants are a commonly used process aid, but their impact on the structure and settling properties of high clay content tailings is not well understood. The paper describes the changes in composition and bitumen release that occur when mature fine tailings (MFT) are treated with a polymeric dispersant (lignosulfonate.) Synchrotron-source computed tomography (CT) was used to obtain high-resolution 3D images of samples prepared at varying dosages of dispersant. The CT method permits a powerful visualisation of the internal structure and composition of the samples. These insights will enhance our understanding of the structural characteristics of mineral tailings relevant to solid-liquid separation by flocculation and thickening. Keywords: Dewatering, dispersion, dispersants, chemical treatment, computed tomography

Jan 1, 2020