Search Documents

By Nicolle Krusberski

Potential errors in XRF analysis are discussed and investigated with specific reference to the analysis of ilmenite samples. A selection of ilmenite samples was chosen and prepared using two XRF preparation techniques: pressed powder pellet and unroasted fusion bead. The merits of the two methods have been discussed in this paper for ilmenite analysis by XRF. Recommendations have been made regarding the use of pressed powder pellets especially with regard to the mineralogical effects that were evidenced during this investigation. The fusion bead technique was found to be far more accurate and able to meet short turnaround requirements provided the calibration methodology used is specific to the grade of samples analyzed.

Jan 1, 2014

By M. U. Ozbay, D. R. Lougher

An in-situ experimental programme was carried out to improve the understanding of the rockmass and pillar behaviour in moderately deep hard-rock mines. The experiments were carried out at Impala Platinum mines and consisted of precise levelling measurements in the footwall of the reef, stress measurements in pillars, convergence measurements in the stope, and petroscope observations in pillars. The results were analyzed using a computer program in an attempt to quantify the characteristic behaviour of the rockmass as well as the pillars. The measured off-reef displacement data were found to co11fonn to the trends obtained from elastic modelling and the correlation could be improved by modelling the small pillars with reduced modulus to simulate yielding' of the pillars. The stress strain curve obtained from analyzing the in situ results, showed that a 6x 3 xl m pillar yields without significant load shedding at peak stress levels of approximately 208 MPa. The closure measurements confirmed that the mechanism of yielding is mainly that of pillars punching into the foundations. Slight to moderate sidewall fracturing and slabbing might be contributing to yielding, but to a much lesser degree than the former mechanism, as the petroscope observation revealed the existence of an intact region beyond 0,6m from the pillar sides.

Jan 1, 1995

By A. Drumond, J. F. C. L. Costa, M. G. Lemos, A. L. Rodrigues, F. G. Niquini

The past decade has seen a renewed possibility of using machine learning algorithms to solve a large collection of problems in several fields. Data acquisition for mining operations has increased with the growth in sensor-based technologies, and therefore the amount of information available for mining applications has dramatically increased. Ore sorting equipment is available for separating ore from waste based on differences in physical properties detected by a real-time analyser. The separation efficiency depends on the contrast in these properties. In this study we investigate the application of machine learning models trained using data from the output of a dual-energy X-ray ore sorting apparatus at a gold mine. The particles were first hand-sorted into ore and gangue classes based on their mineralogical composition. Classification models were then used to help decide the balance between the number of true and false positives for ore in the concentrate, with a view to economic parameters, using their receiver operator characteristic (ROC) curves. The results showed AUC (area under the ROC curve) scores of up to 0.85 for the classification models and a maximum reward condition Fpr/Tpr around 0.5/0.9 for a simplified economic model.

Aug 8, 2024

For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984. New President On 29th March, 1985, Mr B.C. (Bertie) Oberholzer, Manager of East Driefontein Gold Mine, was elected President of the Association of Mine Managers of South Africa for the ensuing year. Bullion from old film A pollution-free chemical method of producing silver that is 99 per cent pure-and therefore of bullion quality-from scrap photographic film and paper has been developed by a British company.

Jan 1, 1985

By S. R. Grobler, S. Bilessuris, M. E. Greenway

Ensuring that all the head ropes on a multi-rope friction winder share the load equally has been a design and maintenance issue since they were first developed. Accurate machining of the rope grooves is necessary to meet this objective. Early analysis of the change of rope loads for ropes in grooves that are mismatched in depth treated the grooves as rigid. Groove depth tolerances deduced from this analysis are stringent and difficult to achieve in practice. Test work indicated that the inherent flexibility of groove lining materials alleviates the load-sharing problem. However, no analysis of rope load changes due to mismatched flexible grooves has been published. In this paper we develop new equations for the rope load variation for flexible grooves. By allowing flexibility to reduce to zero, the corresponding rigid rope groove equations are obtained. New criteria for tolerable groove depth variations are developed from this analysis, which depend on the flexibility of the groove lining material.

Sep 1, 2021

By D. F. Malan, P. J. Le Roux

Almost no work has been published on the strength of pillars in mines exploiting the LG6/LG6A chromitite bands in the Western Bushveld Complex. The strength of these pillars is unknown, and the hard rock industry still uses the Hedley and Grant formula. Numerical modelling, using inelastic constitutive models, may be of some value in estimating the pillar strength, but this approach is difficult and prone to errors as many assumptions are made. This paper explores the alternative approach of the back-analysis of actual LG6/LG6A mining layouts, using displacement discontinuity codes to simulate the average pillar stresses on a mine-wide scale. From this, and underground observations, a ‘minimum’ pillar strength (K-value in the pillar strength formula) can be estimated. The codes TEXAN and Map3D are both used in the paper to simulate the actual pillar shapes and sizes in an LG6/LG6A mine. The results are encouraging as the two codes produced similar APS values for a complex pillar geometry. An estimated K-value of 77 MPa was determined for the LG6/LG6A pillars in this particular area. This is more or less similar to earlier work done for the UG2 chromitite seam, but higher than the K-value of 39 MPa for a linear formula obtained by other workers for LG6/LG6A pillars. Caution should therefore be exercised before using this higher value for all areas. The effect of element sizes and explicitly simulating the effect of the surface for shallow pillars is illustrated in the manuscript using both codes. The need for actual pillar observations and an iterative design process, which cycles between modelling and observations, is also emphasized.

Nov 27, 2024

By P. S. Piper

In the 1960s it was suggested that the volume of stope convergence, and hence the rockburst hazard, could be reduced by the emplacement of backfill. Recent advances have facilitated the placement of large quantities of backfill underground, and a reassessment of its potential benefits as part of a regional support strategy is now timely. In this paper the principal criteria of effectiveness of backfill are taken to be its impact on face energy release rate (ERR) and average pillar stress (APS) levels, and maximization of acceptable ore extraction ratios. The possible effects of backfill on excess shear stresses (thought to modulate large seismic events) are also briefly reviewed. Analytic solutions describing backfill properties and their impact on ERR and APS in certain idealized geometries are also presented, and compared with the results of an extensive suite of computer simulations, in which parameter sensitivities are explored. Results indicate that a regional support strategy is required at depths exceeding 2 km in order to maintain acceptable levels of ERR, and backfill ribs can on their own fulfil this role at depths less than 3,3 km. At greater depths use of stabilizing pillars becomes imperative, but here too supplementary backfill ribs can reduce ERR and APS levels and permit significant increases in ore extraction ratios.

Jan 1, 1988

By T. Bruce, R. C. A. Minnitt

Mining operations are generally reluctant to install high-cost sampling systems at operations that have been functioning for many years. The principal objection to installing appropriate equipment to extract correct and representative samples in process flows is the time and costs involved. The Theory of Sampling (TOS) provides a structured framework for identifying and quantifying the errors and bias associated with any sampling event, but this may be insufficient to initiate substantial investment in correctly designed sampling equipment. Financial losses arising from substandard sampling installations are usually disregarded because the value-add from a good quality sampling solution is invisible, but the cost is quite obvious. Depending on the needs, a less-than-perfect or fit-for-purpose sampling solution may be acceptable, provided the magnitude of sampling errors is understood and the assay results are interpreted accordingly. Categorical levels of acceptable accuracy and precision can be established depending on the sampling position in the mining value chain and the nature of the decisions to be made. The objective benefits of proposed fit-for-purpose sampling solutions should be presented to relevant decision-makers in such a way that adverse subjective decisions are countered so that appropriate solutions are implemented. Practical examples of the benefits from motivating the implementation of fit for purpose sampling solutions at sampling facilities around the world are provided.

Jul 2, 2022

By W. D. Grimsley, R. P. King, J. B. See

Samples (15 to 20 g) of pre-calcined Mamatwan manganese ore or pure Mn 304 smaller than 48 mesh were reacted at temperatures in the range 1000 to 1300°C with samples of spectrographically pure graphite smaller than 325 mesh. Samples (1 g) of ore or pure Mn02 smaller than 48 mesh were reacted at temperatures of 1000 and 1200°C with pure graphite fines in argon, with graphite in carbon, .'1onoxide, and with carbon monoxide alone. In each case, the loss of mass as a function of time was recorded with a hermobalance. The rate and degree of reduction were found to increase with additions of carbon and with increasing temperature up to 1300oC, when they reached their maximum. The shape of the reduction curves, together with the results obtained from examination of the products of reaction by microscopy and X-ray diffraction, were used as the basis for a postulated reduction mechanism. Some details are given of an initial kinetic model that was used to verify the proposed mechanism. It was found that the reduction of Mamatwan ore by graphite at temperatures in the range 1000 to 1300°C occurs in two stages: (i) an initial stage during which the higher oxides of manganese are rapidly reduced to MnO with concurrent formation of CaMn2O4 and (ii) a longer stage during which CaMn2O4 and MnO are reduced to carbides by carbon dissolved in the ferromanganese phase.

Jan 1, 1978

By C. Fiore

The annual general meeting of the branch was held in the Witbank Golf Club on Thursday, 28th August, 1969 at 5:00 p.m.

Nov 1, 1969

By T. Steyn, M. Fofana

"One of the most important performance indicators of a dense medium cyclone (DMC) circuit is the Tromp curve, and by extension the separation density and Ecart Probable (Ep) values. The densimetric profiles of DMC product streams have been traditionally acquired using heavy liquid sinkfloat analysis, which has certain disadvantages, such as the associated safety and health risks. More recently, non-toxic media such as lithium hetero-polytungstates (LST) have been used, with the desired densities being achieved by maintaining the solutions at specific temperatures. However, the high costs of these liquids can be prohibitive. The long turnaround time of the sink-float analysis is a further disadvantage for timeous interventions to the operating set-points of the DMC process.The RhoVol technology can generate the density distribution of a batch of particles in a rapid, accurate, repeatable, and safe manner. Additional data of interest, such as particle size and shape, are also measured and reported on a per-particle basis. Furthermore, samples can be sorted into discrete sorting bins based on any of the measured parameters of the particle, making further analyses of the material possible.This technology has applications across all commodities that use the DMC, particularly in the size fractions –25 +8 mm and –8 +3 mm. To date, laboratory results have proved very encouraging – separation densities are within 5% of traditional sink-float results, and the technology is being introduced to diamond DMC plants. IntroductionDense medium separation is a commonly applied beneficiation technique for the density separation of valuable products from crushed ores. The industrial applications of dense medium separation have been summarized and reviewed by various authors (Scott and Napier-Munn, 2000; Bosman, 2014; Napier- Munn, 2018). Dense medium cyclones (DMCs) are widely used in the coal and diamond industries to produce clean coal or to preconcentrate kimberlitic ores, respectively. Cyclone performance (separation density monitoring) techniques are varied. In the mineral industry. Density tracer tests (Napier- Munn, 1985, 2014; Davis, Wood, and Lyman, 1985) without mineral material, are widely used, although their accuracy in predicting operating cut-points becomes limited once mineral material is introduced. More recently, radio frequency tracers have been also used for the determination of cyclone efficiency (Partition Enterprises, 2017)."

Feb 1, 2019

By M. Yavuz

Determining the most convenient plant location is one of the most commonly encountered problems in engineering applications. This paper presents a fuzzy multiple attribute decision making (FMADM) model which is developed for the selection of the optimum plant location for natural stone factories in the mining industry. The criteria affecting the decision making process in natural stone industry were determined to solve the plant location problem in the FMADM model. To determine the optimum plant location for a new natural stone factory, which is planned to be established by a mining firm located in the Eskisehir region of Turkey, an analysis was carried out by incorporating the method and the analytic hierarchy process (AHP) method. The analysis shows that the Yager?s method can easily be applied to the selection of plant location in the natural stone and mining industry when the difficulties encountered in the application process of the AHP method is taken into account. Keywords: Natural stone, plant location, decision making, Yager?s method, analytic hierarchy process (AHP).

Jan 1, 2008

By C. R. Speers

The induced elastic stresses in the sidewalls of gold-mining tunnels at a depth of 4000 m in the Witwatersrand exceed the peak compressive strength of even the best-quality quartzite rocks. Laboratory tests measuring post-yield stress versus strain response show that brittle fracture occurs, followed by a loss in strength associated with strain-softening behaviour. Numerical modeling based on an assumed Mohr-Coulomb criterion fitted to the test results shows that large ongoing deformations of the sidewall occur, leading to total tunnel failure without adequate support. A methodology is presented to enable a quick assessment to be made of support requirements in terms of ground characteristic curves for numerically derived pressure versus displacement. From these curves, estimates can be made of the force levels for cable bolting and of the thickness and strength requirements for shotcrete linings. As an example of its application, the methodology is used in a comparison of the relative stability efficiencies of a square-shaped tunnel and a horizontal ellipse-shaped tunnel.

Jan 1, 1996

By E. Córdova, A. Anani, W. Nyaaba

Optimization of panels, haulage fleet, and waiting area involves deterministic and low-fidelity methods and experiential knowledge. The process is challenging because coal recovery and operational capabilities must be considered in the solution. The approach in this manuscript comprises the development of an integrated stochastic simulation model of a coal room-and-pillar system that addresses these challenges. The decision variables evaluated are panel width, number of shuttle cars, and change-out time (COT). The results show that the mine should implement the shortest possible COT, decreasing the cycle time and thereby increasing productivity and continuous miner (CM) utilization. The highest productivity and CM utilization for a fleet size of three shuttle cars is found in the 15-entry panel width. For the evaluated fleet sizes, the 19-entry panel width is optimal for the four and five shuttle cars. Among the three variables studied, panel width and fleet size had the most significant effects (5% increase) on the CM productivity, cycle time, and utilization.

Apr 2, 2022

By M. Royle, A. Bloem, R. Uken

Rock mass damage induced by mining increases the fracture frequency and joint aperture width in the pit walls and rock mass behind open pit mine slopes. The depth and intensity of this mechanical damage relative to the pre-mining state is not well understood and yet is a major factor in the development of slope stability models and operational guidelines. The induced damage can be partitioned into domains or zones. The blast damage zone is essentially a ‘free flow’ rock mass volume, which transitions quite rapidly into the excavation damage zone, which extends beyond that. In both zones, transient high in situ water pressures are often linked to unstable slope conditions. Whereas rock damage can enhance passive depressurisation in the rock mass, high infiltration rates on the other hand, as one could expect during rainstorm events, will decrease slope stability within the dilated pit rock mass, especially in the blast damage zone-excavation damage zone, by increasing pore pressures for short periods of time. Ice jacking and freshet are additional factors to consider in (sub) arctic environments and can be exacerbated by unfavorable rock fabric orientation. On a local scale, brittle deformation damage zones, in the form of faults, can contribute to slope instability, or enhanced stability because of slope depressurisation, depending on their location and orientation relative to the pit shape and the water sources. In this study, the shapes of the damage zones and their anticipated impact on infiltration and/or passive depressurisation are considered for different pit morphologies, rock mass conditions, in situ stress, and hydrogeological settings. Some unusual hydrological situations, like mining towards rivers and lakes and the potential effects on pore pressures, are also considered. This investigation has resulted in the development of a method to adjust initial hydraulic conductivity values used to estimate transient pore pressure conditions found in rock masses exposed in different pit morphologies and stress regimes as well as discontinuities’ orientation relative to open faces within the open pit mine. The changes in K values and pore pressures can then be used to determine hydrogeological influence more accurately on future pit slope stability.

Sep 1, 2025

By T. Ono, B. Altansukh, S. Kawamura, K. Haga, A. Shibayama, Y. Takasaki

In recent years, the grade of silica in zinc concentrate has increased due to the degradation of zinc content and the increase in impurity content in natural ores. It implies that the development of silica removal technology from zinc concentrate is necessary to solve problems in the smelting process caused by the high content of silica in zinc concentrate. In this paper, the authors investigated the silica removal processes from silica-rich zinc concentrate by mineral processing approaches such as re-grinding and flotation. This study focused on the pulverisation process as a pretreatment for the investigation of individual minerals' liberation from the silica-rich zinc concentrates using different kinds of pulverisers. Flotation experiments were performed to separate silica and zinc concentrate from the pulverizsd feed sample using a pH regulator (NaOH), activator (CuSO4), collecting agent (PAX), and foaming agent (DOW froth 250). Results showed that the liberation rate of silica (SiO2) was reached 75% from 13% by pulverisation in an attritor with a 2 mm ball in diameter, while silica accumulated in a fraction over 20 mm in size. Flotation experiments indicated that silica removal efficiency was achieved by 44% from + 20 mm fraction obtained from pulverisation whereas the grade of silica in froth reached 1.85 mass% from 4.5 mass%. Results indicate that silica could selectively separate from silica-rich zinc concentrate, and 99.8 % zinc recovery is achieved under the studied conditions. Keywords: Zinc concentrate, silica, pulverisation, liberation, sieving, flotation

Jan 1, 2020

By B. P. Watson

The discussion written by Dr de Frey suggests that mine design should be based on closely spaced stability pillars. However, this concept leads to low extraction ratios at depth. The concept of `crush' pillars in conjunction with more widely, appropriately spaced stability pillars allows for significantly larger extraction ratios, particularly at depth. It should be noted that the rock conditions in many areas of South African platinum and gold mines are good, allowing significant spans to be mined safely between stability pillars. `Crush' pillars are cut small enough to fail stably near the face under stiff loading conditions, and their residual strength is intended to support about 10 m rock height between stability pillars. While this support resistance cannot be achieved by conventional support, crush pillars have been proven to have the required capacity for this purpose. The concept of leaving smaller crush pillars with appropriately positioned stability pillars has been used successfully for more than 30 years in areas of South African platinum and gold mines.

Jan 1, 2011

By B. Litt, D. L. Van Coller

Job evaluation and the changing wage pattern by D. L. VAN COLLER, B.A.(Cape Town), M.A., B.Litt.{Oxon.) (Visitor) This paper sets out to show how changing forces are affecting the techniques that have been used in the evaluation of Black jobs on gold mines in the Anglo American Group since the introduction of job evaluation in 1961. Initially, job evaluation was essentially a management tool designed to differentiate jobs in a limited skill spectrum and thereby permit the establishment of a 'many stepped' job ladder for Black employees to climb. With the changing wage pattern, job evaluation is becoming an industrialrelations tool aimed at recognizing the skill and effort contributed by the worker so that the pay relationships between jobs are seen to be equitable by the employees.

Jan 8, 1974

By C. J. Lenz

The results of prospecting operations involving geological data and a large number of geochemical determinations of the metal content of soil samples are plotted and evaluated by computer. Anomalous areas are identified in each type of environment by selecting probability or population boundary values from frequency distributions. The anomalies are plotted to permit correlation with geographical or geological features. Ranking of prospecting targets is made using geographic pattern, geology, absolute value and metal ratios. Three short case histories are presented.

Jan 1, 2014

By R. T. Tshikhudo

Nanotechnology can provide solutions to many of the world?s socio-economic challenges. The application of nanomaterials for water treatment and analysis, point-of-care diagnostics and targeted drug delivery systems or devices could improve the quality of life for people in developing countries. Gold colloids have a long history (dating back to the 4th century AD) and are particularly well known for their aesthetic appeal and their therapeutic properties. Since Faraday published a report on the synthesis and properties of colloidal gold in 1857, a reasonable insight into the nature of gold sols (nucleation, growth and kinetics of coagulation) has been developed. Considerable attention has been drawn during the past few decades to the development and optimization of methods for the preparation of gold nanoparticles. In nanoscience and nanotechnology today, gold nanomaterials appear to be the most widely used material by both academics and industrialists. This is due to the extraordinary properties of gold nanoparticles (e.g. optical, catalytic, and magnetic?they are also known to act as strong Raman enhancers and may also amplify fluorescence under certain circumstances). Mintek, through Project AuTEK and the DST/Mintek Nanotechnology Innovation Centre (NIC), has been at the forefront of the development of new industrial uses for gold. Mintek?s gold nanotechnology programme focuses on the development of gold-based nanostructured materials and their applications in health, water and other related areas. While few projects use gold nanoparticles for water treatment and analysis, Mintek?s gold nanoparticles are widely used in the health sector. For example, gold nanoparticles are engineered and produced in large quantities as systems for targeted drug delivery. They are also used as tools for advanced rapid diagnostic tests. Both optical and electrochemical rapid diagnostic methods are developed for the human and animal health sectors for point-of-care testing. This paper gives a brief introduction and overview of gold nanotechnology, and desrcibes the development of some of Mintek?s gold nanoparticle targeted drug delivery systems and lateral flow point of care prototype devices.

Jan 1, 2009