Search Documents

By P. A. Laxen, P. J. van Staden

Alternative procedures for the recovery of gold from old sand dumps are discussed, with emphasis on the use of heap leaching. The modification of material to improve its permeability prior to heap leaching is not currently receiving much attention in South Africa. The channeling of solutions through heaps and the high consumption of reagents sometimes ascribed to heap leaching can, as shown by the results described in this paper, be lessened by desliming of the sand prior to heap leaching and the treatment of the resulting slimes fraction by agitation leaching and carbon-in-pulp. This combined procedure results in a higher overal recovery of gold. Alternatively, the sand can be heap-leached as it is after agglomeration with lime and cement, which improves the mixing and neutralization of the material, as well as lessening the probability of channeling.

Jan 1, 1988

By M. C. Harris

Float-sink analysis has wide application in the coal laboratory. This paper evaluates the established methods used for the float-sink analysis of fine coal, and then describes a new method and apparatus that can be used for material down to a few micrometres in size. The method is rapid and accurate, and requires only a small amount of sample. The results presented show close agreement with the float-sink analyses obtained by the more classical technique using separating columns. The new centrifugal method reduces the time required for the analysis by a factor of ten.

Jan 1, 1986

By G. J. de Korte

South Africa is reliant on coal for the generation of almost all the electricity used in the country, and several large industrial concerns such as Sasol are also coal based. Research relating to the mining, beneficiation and utilization of coal is important in order to ensure the optimal exploitation and use of coal within the country. The Fuel Research Institute (FRI) of South Africa was established in 1930 to investigate all aspects of coal beneficiation and utilization in South Africa. The FRI went on to conduct world-class research and in 1957 a pilot coal preparation plant was constructed in Pretoria to enable large-scale practical experimentation. The pilot plant played a pivotal role in the establishment of South Africa?s low ash coal export project. Political and economic factors contributed to the eventual closure of the FRI and South Africa experienced a period of about 10 years between 1990 and 1999 during which very little public coal preparation research was done. This changed for the better towards the end of 1999 when Coaltech 2020, a collaborative research program was established. Participants included the CSIR, universities, the government and the major coal producers. Coal preparation research conducted under Coaltech thus far include dewatering and drying of fine coal, size classification of ultra-fine coal and dense-medium fine coal beneficiation. Currently, the Coaltech focus is on the beneficiation of low-grade coal reserves and is investigating existing as well as new techniques that can be utilized to provide cost-effective beneficiation of low-grade raw coals and reject coals.

Jan 1, 2010

A description is given of a simple, cheap device that enables the intact shear strength of rock to be determined quickly and inexpensively. Thin rock plates, prepared with a diamond saw, are tested in double shear by a linear punching action. By varying the direction of the diamond-saw cut in a number of specimens, the change in shear strength can be measured for different orientations relative to the rock fabric.

Jan 1, 1980

"Chairman: Professor E. P. PFLEIDER Rapporteur: Mr P. R. JANISCHPapers:Optimum design of an open pit by D. A. PhillipsAn open pit design system for stratiform ore bodies by L. A. J. Pronk van Hoogeveen, J. R. Cutland and M. WeirAn open pit design model by R. H. Robinson and N. B. PrennThe Chairman in opening the session highlighted the current situation in the United States of America where some 85 to 90 per cent of all mining (except for coal) is done by open pit methods, and where some 40 per cent of the coal is mined by open pit. The South African industry is, of course, dominated by the deeper level underground gold mines; however, with the aid of an extensive open-pit technology developed in other countries, South African companies arc continuing to explore possibilities of open-pit exploitation of base mineral, coal and diamond deposits. Several successful ventures are already in operation at Phalabora, Optimum Colliery, Kimberley and elsewhere, and South Africa is undoubtedly benefitting in this regard by drawing on the experience of others.The papers of this session were therefore particularly pertinent, particularly when viewed in conjunction with those presented at an earlier South African conference devoted specifically to open pit mining.Two themes dominated the discussion which followed presentation of the three papers at this session. The first related to the practicability of using the reported techniques as a tool for management, and their acceptability as such to mine management. This was, of course, not peculiar to this particular session, but rather the major point of debate over the entire conference.The second theme concerned the reliability of the initial drill hole data on which any open-pit design must necessarily be based. This gave added emphasis to the problem of practicability, for no management is likely to accept an elaborate pit design unless confidence can be placed in the ore reserve assessment.In noting these two features of the discussion, it should be remembered that all the three papers dealt largely with design and pre-planning; there was an unfortunate lack of papers or discussion on the subject of controlling the day-to-day mining of open pits, and this is an area where the potential impact which can be made by the computer is even greater.In introducing his paper, Mr D. A. Phillips pointed out that it was concerned only with optimization, and that it therefore assumed, firstly, an adequate subdivision of the orebody into ore blocks characterized by grade, rock type, structure, etc., and, secondly, an acceptable forecast of costs and mineral prices in order to generate a suitable profit matrix. However, programs dealing with these problems for both massive, disseminated and stratiform ore bodies are available to Roan Consolidated Mines. The method of optimization which he had described had been used on a region split into 28 000 blocks, for which the program used three hours of C.P.U. time on an IBM 360/40 computer. The computer design had provided a three per cent improve¬ment on a normal design of the same area."

Jan 1, 2014

By P. S. Turner

After a brief account of the differences between the control of underground fires and those on the surface, the paper describes the analogue detection system used on the mines of the Anglo American Corporation of South Africa Limited. The system comprises Spanair gas analysers, Becon combustion-particle detectors, a telemetering system, a surface signal-recording and-processing system, and an alarm system. The use of the system is described and illustrated.

Jan 1, 1982

By G. T. C. Emere, E. C. Hunter

The use of cylindro-conical settlers for the clarification of underground water by E. C. HUNTER- (Associate) G. T. C. EMERE-, B.A. (Hons.) (Keele) (Visitor) This paper analyses the performance of conical settlers on Harmony Gold Mine from 1959 to the present time, and describes the investigation that was undertaken to substantiate and improve the use of conical settlers for a new pump chamber in another part of the mine.

Jan 5, 1977

By C. van der Merwe, R. Lumbule, J. Kgomo

"The mining industry in the Democratic Republic of Congo has seen a significant expansion in copper and cobalt production in recent years. The greater proportion of this expansion has arisen through processing of oxide ores. The design of metallurgical processes for these oxide ores is based on the conventional equipment and layout for processing of sulphide ores, and comprises milling followed by leaching, solvent extraction, and electrowinning. The physical characteristics of the oxide ores, however, provide the process design engineer with an opportunity to examine critically the principles on which equipment selection is based and to design processes better suited to these ores. In 2015, ERG Africa began a project to expand the leaching capacity of the Luita hydrometallurgical facility. A number of innovative changes to the conventional process design were included in the modified flow sheet, which were validated when the project reached design throughput in November 2017. Of these changes, the most novel presented an alternative approach to mitigate the impact of colloidal silica on the operation of the solvent extraction plant. Introduction ERG Africa operates the Luita hydrometallurgical facility located at Kakanda in the Democratic Republic of Congo (DRC), treating malachite and heterogenite minerals to recover copper as electrowon cathode and cobalt as a hydroxide precipitate. The process was originally conceived as a heap leach operation followed by direct electrowinning of copper, with solvent extraction (SX) and electrowinning (EW) of cobalt. In preparing the sized ore for the heap leach operations, the undersized ore fraction at a P80 of 625 µm was discharged to a fines storage facility for later processing. This fraction carried with it approximately 30% of the copper contained in the run-of-mine (ROM) ore feed, and an equivalent proportion of cobalt.In a subsequent development, the cobalt SX section was converted to a copper SX facility, the leached cobalt being recovered from a bleed stream from the copper heap leach circuit. The operating cost for the process as then installed placed this facility well in the fourth quartile of the industry cost curve. The initial Luita operation was established in 2010 at a time when metal prices were above long-term averages (copper above US$3.00 per pound; cobalt above US$20.00 per pound), and the drop in prices in 2015/2016 presented a major challenge. The London Metal Exchange (LME) copper price dropped below US$2.00 per pound, with cobalt dropping below US$10.00 per pound in Q1 2016. This set in motion a range of improvement initiatives for the Luita operation. Central to this was the installation of a tank leach circuit to process the discarded fines and a modified SX circuit to manage colloidal silica. The revised Luita circuit reached design capacity in November 2017 and has proven to be well suited to processing of the oxide ore feed. This process design challenges the boundaries of conventional thinking in the areas of leaching, solid/liquid separation, solution management, impurity management, and metal recovery, and is the subject of this paper."

Nov 1, 2018

By W. A. Te Riele

The National Institute for Metallurgy was the venue for a one-day colloquium on 'The Chemistry of Processes for the Recovery of Gold on Activated Carbon'. Organized by the South African Chemical Institute (Southern Transvaal Section) in collaboration with the National Institute for Metallurgy (NIM) and the South African Institute of Mining and Metallurgy, the colloquium attracted tremendous interest from the mining industry. Some 300 metallurgists, engineers, and chemists were brought up to date on advances in this technology made by scientists of NIM and the Anglo American Research Laboratories (AARL).

Jan 1, 1980

By A. Koursaris, J. B. See

The influence of Iscor coke and Delmas coal on the reduction of Mamatwan manganese ore to ferromanganese was examined by use of a variation of the 'stationary charge in controlled environment' (SCICE) technique. The charges of Mamatwan ore and the appropriate reducing agent were heated to temperatures between 1300 and I600 °C and either allowed to cool immediately the required temperature had been reached or held at that particular temperature for periods of up to ... hours. The heating rate was 350°C per hour, the particle size of the ore was between 2,83 and 12,7 mm, and the particle size of the reducing agent was between 2,83 and 6,35 mm. After being allowed to cool in air, the reacted charges were examined by optical microscopy, X-ray-diffraction analysis, scanning electron microscopy, and electron-microprobe analysis. No significant difference was found between the changes observed during the reduction of Mamatwan manganese ore by Iscor coke and by Delmas coal. A hypothesis is advanced to explain the mechanism of formation of the Fe-Mn-C alloy.

Jan 1, 1979

By J. E. Robinson, W. Pilkington, J. L. Taylor, B. J. Bluhm, E. B. Viljoen, P. Le Grange

The Chemwes uranium plant was designed and constructed within fifteen months; commissioning started during. June 1979, and the plant was producing at design capacity four months later. This account highlights the procedures and methods adopted to bring the plant Into production. The description of the various phases includes some details of the early evaluation, and the feasibility and optimization studies; of the financing, project management, design, construction, and commissioning of the plant; and of the training of personnel. Some of the mistakes made and the factors that contributed to the success are also listed.

Jan 1, 1981

Contribution by G. Narsimhan It was with much pleasure that I went through D.F. Malan's excellent paper. The following explanatory and critical note has been the result of my deep study of the paper. Although by qualifications and experience I have been a chemical engineer, involved over four decades with problems in the modeling and simulation of transport-limited (heat and mass) chemical reactions in multi-phase systems, I have of and on interested myself in challenging problems in extractive metallurgy. This is the first time I have veered of to continuum mechanics, at the age of 71! Author's reply. I thank Professor Narsimhan for his extensive contribution to the paper. It provided me with the stimulus to derive an extended model. However, there are some inaccuracies in his arguments that need further discussion. Professor Narsimhan's main concern is that there is not a good enough fit between the derived viscoelastic Kelvin model and the experimental data supplied by Güler1 (see Figure l1 on page 218 of my paper). I will therefore explain the choice of a viscoelastic model in more detail and also make specific comments on the arguments given in his contribution.

Jan 1, 1996

By F. Lanaro, K. Röshoff, R. Christiansson, L. Jing

This paper presents the results of a project for developing a methodology for empirically determining some of the mechanical properties of the rock mass at the Äspö Hard Rock Laboratory, Southern Sweden. Using the equations available in the literature, the deformation modulus, friction angle, cohesion and unconfined compressive strength of the rock mass were estimated. A comparison of the results using different classification methods (Q, RMR, GSI, RMi, Ramamurthy’s) was made to estimate the range of variations in the mechanical properties with the considerations of: i) the quality/quantity of the geological data; ii) the technique for partitioning of the rock mass into homogeneous domains; iii) the sensitivity and subjectivity of the empirical methods; and iv) the need for validating the empirical methods against a test case. Cet article présente les résultats d’un projet visant à établir une méthodologie, pour déterminer, de façon empirique, les propriétés mécaniques de la masse rocheuse. En utilisant les corrélations disponibles dans la littérature, quelques-unes des propriétés de la masse rocheuse ont pu être déterminées (module de déformation, angle de friction, cohésion, force de compression illimitée). Une comparaison des résultats obtenus par différentes méthodes (Q, RMR, GSI, RMi, de Ramamurthy) a permis d’établir une échelle de variations des propriétés mécaniques et de formuler une série de recommandations concernant : i) la qualité/quantité des données géologiques ; ii) la technique de partition de la masse rocheuse dans des domaines homogènes ; iii) la sensibilité et la subjectivité des méthodes empiriques ; iv) la nécessité de valider les méthodes empiriques à l’aide de nouvelles études de cas. Dieses Paper präsentiert die Ergebnisse eines Projekts mit dem Ziel, eine Methodik für die empirische Festhellung von mechanischen Eigenschaften im Gesteinmassiv zu etablieren. Durch Verwendung der in der Literatur zugänglichen Korrelationen, wurden einige Eigenschaften des Gesteinmassivs festgestellt (Entstellungsmodul, Reibungswinkel, Kohäsion, unbeschränkte Kompressionsstärke). Ein Vergleich der Ergebnisse unterschiedlicher Methoden (Q, RMR, GSI, RMi, Ramamurthy’s) wurde durchgeführt und dies erlaubte die Feststellung der Variationsskala von den mechanischen Eigenschaften, sowie eine Reihe Empfehlungen für: i) Qualität/Quantität der geologischen Dateien; ii) die Technik für Teilung des Gesteinmassivs in homogene Domäne; iii)die Empfindlichkeit und Subjektivität der empirischen Methoden; iv) das Bedarf die empirische Methoden gegen neue Fallgeschichten zu validieren.

Jan 1, 2003

By E. L. Atkinson, G. W. Leach

The paper discusses the reasons for the introduction of load-haul-dump (LHD) units into Greenside Colliery, and the circumstances leading to the replacement of conventional mechanized equipment on a trial basis in the mining operations on No. 2, 4, and 5 seams. An outline is given of the factors governing the selection and introduction of these units into coal mining, and the associated mining and engineering aspects involved in the optimization of their use. Operating statistics comparing the performance of conventional and LHD equipment are included.

Jan 1, 1979

By P. J. Petit

Financial evaluation is necessary to investigate the viability of implementing and/or utilising new technology in mining projects. It establishes a techno-economic base for decision-making and justifies capital expenditure. This paper aims to present a monetary appraisal of the electric rock drilling system in a typical feasibility project, whose purpose is to increase the production rate. The in situ environment is a platinum orebody, and the stoping operations occur in UG2 reef. The results are a function of production requirements, technical parameters and financial outlay of the drills. The costs involved in implementing and operating electric rock drills are assessed to the current method of drilling, namely the compressed air operation. A comparison of the electric and pneumatic rock drills in terms of financial outlays for drilling and service requirements, peripheral equipping and training is discussed. Other factors that affect the business case are technical advantages, safety and risk management and the environmental objective of the company.

Jan 1, 2006

By Jean-Claude Paye

In February 1996 the OECD's Environment Policy Committee will commemorate its 25th anniversary with a fifth meeting at Ministerial level. Environment ministers will be taking stock of the progress made by OECD countries in protecting and managing the environment in that quarter-century, and sharing views on likely challenges and co-operative responses. Ministers can point to many important accomplishments. Scientific understanding and technological tools for establishing and monitoring risks to human health and the environment have improved dramatically since the early 1970s. All OECD countries now have in place comprehensive environmental legislation, supported by specialized institutions for policy design, implementation and enforcement. The results of these efforts are increasingly evident in the form of cleaner air and water, and improved protection of natural areas, notwithstanding the many complex problems that remain.

Jan 1, 1996

By F. Bourgouin

Thirty-one years ago, African leaders met in Lagos for the drafting of the Lagos Plan of Action for the Economic Development of Africa, 1980?2000. The main objective of the plan was to increase Africa?s self-sufficiency and in this regard, the plan had a section pertaining specifically to redressing the ills of an unproductive mining and minerals industry and harnessing its potential for socio-economic development. However, if we look at the nature of this sector on the continent today, its characteristics resemble the diagnosis of the sector given in the plan back in 1980: lack of information on endowments of minerals; lack of value added in the sector; low development and use of those endowments that are not of interest to transnational corporations (TNCs); and most importantly, low contribution to socio-economic development. The primary consequence of the lack of visible benefits to African states, despite growth and development of the sector in terms of increased mining activity led by Foreign Direct Investment is that countries with mining industries are characterized by dysfunctional internal processes. Improvements in governance, monitored with indices such as those set out in the Extractive Industries Transparency Initiative, the Millennium Development Goals, and other such ?good governance? agendas, are being asserted. However, before we prescribe the introduction of initiatives or guidelines based upon highly subjective norms which we believe to fit this diagnosis, it is necessary to review how it is that we got to this situation that we are in today. How is it that, 31 years after the Lagos Plan of Action, we have not seen any major changes in the role the industry can play in socio-economic development, despite the vast increase in mining activity on the continent?

Jan 1, 2011

By C. Kirmanli

The purpose of this paper is to develop an expert system for hydraulic excavator and truck selection in surface mining. Hydraulic excavators and trucks are finding increasing applications in mining operations. Hydraulic excavators are extensively used especially when bringing electricity to rural areas is difficult and for small-scale mining. This paper describes an expert system, which selects the optimum hydraulic excavator truck configuration such that unit production cost is minimized and technical constraints such as geological, geotechnical and mining constraints are satisfied. The system has four modules: user interface, rules and an methods, databases and output module. The expert system in this study is developed within KappaPC shell. It supports object-orientated technology for the MS Windows environment. The software provides a very useful tool to practitioners, saving time and cost. Equipment selection is a recurring and expensive problem of mine planning and often involves interdisciplinary experts from different fields. It is very difficult and expensive to bring together all these experts. The capabilities of the expert system developed are illustrated in the paper. The software overcomes the difficulties of selecting the proper equipment for surface mining operations, which is very important, and results in substantial savings. Equipment databases for hydraulic excavators with 15-59 yd3 capacities and trucks with 35-360 tons are constructed and these databases are used to select the proper configuration. A case study is carried out for Soma Surface Coal mines in Turkey. Keywords: surface mining, expert systems, equipment selection, hydraulic excavators, diggability

Jan 1, 2009

By E. -U. Reuther

To improve the climatic environment underground the German coal mining industry has installed refrigerators with a capacity of 300 MW cooling power. One third of this total is accounted for by central refrigeration plants with more than 5 MW capacity. The central refrigeration comprises three stages: mechanical cooling, transport and distribution of chilled water via pipelines and exchange of heat in the air coolers. Of these three stages only the mechanical generation of chilled water has been resolved satisfactorily. Transport (including distribution) and exchange require further technical research. The Mining Institute of the Aachen University of Technology has done extensive studies on this subject, concentrating on controlling the flow of chilled water according to demand in the mine. Additionally, the favourable exchange in the air coolers is taken into account. The studies are based on a model mine which simulates the conditions in deep coal mines in Germany. The simulation program represents firstly the condition of the mine air at the location of the air being cooled, then the heat exchange in the air cooler itself, and finally the transport of the chilled water from the central refrigerator to the consumer. The program also reproduces the seasonal and operational changes in conditions of mine air as well as different air cooler designs. A regulated distribution of chilled water is also suggested. Finally, estimations of costs can be made as an aid for further planning.

Jan 1, 1987

By C. J. Badenhorst

Occupational illnesses and diseases tend to be chronic and are generally characterized by temporary or permanent physical dysfunction. With the exception of some symptoms, they are not generally visible. Therefore, safety overrides health in mining because occupational ailments take years to develop and management observes less physical trauma, if they witness anything at all. Occupational health issues need to be addressed systematically, encompassing all aspects of the interaction of employees within the work environment. Risk assessment is central to the management of occupational health. This should not be seen as a complex process and may involve little more than simply considering the consequences of one?s actions before starting work. Competent risk assessment provides the starting point and defines the scope of further action. The objectives and final use of an occupational health risk assessment determine the process and the method by which it is carried out. The occupational health risk assessment is therefore a systematic procedure to identify potential health hazards, evaluate the extent of exposure subjectively and/or objectively, and to establish the need for, and effectiveness of existing control measures. Furthermore, it facilitates the drafting of occupational exposure monitoring, medical surveillance and occupational health education programmes. Various models for conducting occupational health risk assessment provide step-by-step guidance for the identification and assessment of significant occupational health hazards and assist in producing suitable and significant occupational health risk assessments. The paper gives an overview of an occupational health risk assessment model based on the basic principles of occupational health and the legislative requirements, which will simplify the occupational health risk assessment process and ensure a sound base for the development of all other occupational health systems.

Jan 1, 2004