Search Documents

By H. J. de Klerk

The metallurgical phenomena in the design and manufacture of high-strength low-alloy (HSLA) steels are reviewed, and some aspects of the production of Supraform TM (thermo-mechanically processed) steel are discussed. . The weldability of Supraform TM is related to changes in the microstructure of its heat-affected zone.

Jan 1, 1984

By O. K. H. Sheff

Despite many years of a successful policy for our Journal, the Journal Committee is in the course of adopting a new approach with which to enter the present decade. The objectives are to improve the readability of the Journal, without forfeiting the quality achieved in the past, by adding an extra dimension through the inclusion of applied-engineering papers, i.e. technically oriented papers.

Jan 1, 1990

Recent advances in the design and performance of flotation equipment A General Meeting and Colloquium on the above topic was held on 12th March, 1975, at Kelvin House, Johannesburg. The Colloquium was attended by 250 delegates and was opened by the Immediate Past President, Mr P. W. J. van Rensburg, at 09h30. Obituary Mr Van Rensburg announced with regret the deaths of James Alfred Boyd, Life Fellow, and Jack Joseph Frankel, Fellow. Training of technicians The Institute has received a letter from The Federation of Societies of Professional Engineers pointing out that there is considerable opportunity for the training of Coloured and Bantu technicians and artisans, and that the existing facilities will be extended as the demand for them increases.

Jan 6, 1975

By R. E. Gundersen

Hydro-power-the use of high-pressure water as an energy source-offers tremendous benefits for environmental control in deep, hot mines. The extent of these benefits depends on the mining method, the selection of equipment to be hydro-powered, and the efficiency with which the coolth is extracted from the water and into the working environment. The engineering of hydro-power systems continues to receive much attention. However, this paper considers the environmental implications of using hydro-powered equipment, particularly with regard to positional efficiency. The integration of hydro-power with developments such as backfill, mechanization, and higher face-advance rates is discussed. Layouts are proposed that attempt to minimize the quantity of water in circulation by extracting the maximum coolth from the water.

Jan 1, 1990

By T. V. Thoms, T. R. Twidle, J. W. Crous

This note describes an investigation into the most cost-effective material for mil-shell liners in large-diameter pebble mils with lifter bars. This is part of a project being conducted at the gold plant of East Driefontein near Carletonvile in the Transvaal. It was found that manganese-steel and chromium-steel liners are more cost-effective than liners of cast mild steel or white iron.

Jan 1, 1990

The relationships between backfill-transportation parameters (solids concentration, velocity, and pipe diameter) and the wear rate of backfill-transportation pipelines is well understood. However, the degree of wear experienced by a pipeline depends not only on the transportation parameters, but also on the characteristics of the solids making up the backfill, i.e. the particle-size distribution, hardness, shape, and sharpness of the particles. Therefore, unless data corresponding to the specific wear rate of the solids are available, the determination of the wear rate for pipes transporting an uncharacterized backfill is largely guesswork. This paper describes an evaluation of particle characteristics with special reference to particle sharpness so that pipe wear rates can be correlated with solids of different size distributions and sharpnesses.

Jan 1, 1993

By R. J. Dippenaar, W. H. Van Niekerk

The relationships between coal properties, the strength of coke, and the performance of a blast furnace were investigated by means of correlation studies, and a linear programming model was developed for the prediction of a coal blend based on these relationships. The unique feature of this approach is that it utilizes a knowledge of the minimum blast-furnace coke requirements, rather than the maximum attainable coke quality. The model predicts the least expensive coal blend that would still comply with the minimum coke-quality requirements of blast furnace. The study also confirms the existence of a relationship between the rank and caking parameters of coal, and the hot strength of coke. The effect of coke-oven operating parameters on coke quality is also discussed.

Jan 1, 1991

By P. F. S. Jackson, A. Strasheim

In the survey "Analysis of South African raw bullion" the distribution of trace elements within the bullion have been shown to be distinctively dependent on the extraction process. In general the amalgamation process produces the more impure bullion with respect to trace elements. Some chemical and physical explanations are given for the differences that have been observed in the raw bullion as received at the Rand Refinery. The value of the spark source mass spectrographic technique in the study of the elemental impurities in bullion is demonstrated.

By F. P. A. Robinson, J. W. Fourie

Austenitic stainless steels are welded using low-heat inputs. However, owing to differences in the physical metallurgy of austenitic stainless steels and duplex stainless steels, low-heat inputs should be avoided for duplex stainless steels. This paper highlights the differences in solidification mode and transformation characteristics of these two types of alloys. Recent work on the effect of heat input on the properties of weldments of duplex stainless steels is reviewed.

Jan 1, 1990

By M. C. van Blerck

This paper examines the South African fiscal system as it applies to the mining industry and, where components are found wanting, discusses possible alternatives. It is concluded that the South African system has long provided a stable environment for mining investment and growth. However, the introduction, of steep surcharges during the past decade or so (since abolished) and ring fencing (since relaxed but not abolished) has started undermining this stability.

Jan 1, 1994

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By A. K. Haines

Hydrometalurgy, particularly leaching, is a highly topical subject and always generates great interest in the mineral industry. This was evident right from the start of the organization of the SAIMM Colloquium on Leaching, which was held at Mintek on the 8th and 9th November, 1988. The response to the cal for papers was so good that the Colloquium was extended to two days, instead of the usual one day.

Jan 1, 1988

By V. C. Robinson

INTRODUCTION Most presidential addresses are in the nature of a review of some specific topic and this will be no different. In thinking about the subjects which might be suitable for this address I decided that as next month will see my retirement from the gold mining industry I might review the four decades since I started in the industry in 1929. These four decades have been more than usually in',~resting and exciting. They have covered a period when the price of gold increased from the old figure of 84/- an ounce to the price of $35 an ounce today, taking in on the way at least two periods of premium sales from which the producer benefitted. The industry in these four decades has survived the most totally destructive war in history and has seen fundamental changes in the political, economic and governmental life of South Africa. There have been great technological changes and improvements, some of which I shall refer to later, and in addition there have been profound changes in the relations between employer and employee in the industry which have affected not only the economy of the industry but the traditional thinking of both management and labour. I believe that the address presented to this Institute on the occasion of its 75th Anniversary by Mr Goode covered more than adequately the history of the Institute and the part it has played in the mining industry of South Africa. It would be merely repetitive, therefore, to discuss the affairs of the Institute of Mining and Metallurgy. Having said this, however, it is also necessary to point out that the history of the Institute is, and always will be, an important record of the history of mining in South Africa. There are many facets, however, on which we ought to look back and to re-examine. One of the most rewarding, but at the same time one of the dullest, places to look for historical facts is in the annual reports of the Chamber of Mines. I suppose that some of the dullest of these have been the reports for which paragraphs have been prepared by me personally. The notes which follow do not claim to be anything like a full record of this exciting period. RISE AND FALL OF THE GOLD MINING INDUSTRY In talking about the mining industry of South Africa it is inevitable that one talks, particularly in the historical sense, about the gold mining industry - an industry of fundamental importance which has made South Africa what it is and which has been dying since the early part of this century. In Table I is shown the progress of the gold mining industry measured by its output of ounces of fine gold from the beginning of operations until the end of 1969, and if you are interested in the productivity of the men who work this industry the table, composed entirely from figures set out in the Chamber's annual reports, also shows the production of gold expressed as fine ounces per European and fine ounces per Bantu worker over a long period. If you are still minded to think of this industry as dying then the last column in the table shows how uranium has played such a vital part in the prosperity of the country.

By M. Pötsch, M. Blümel, E. A. Button

ABSTRACT: Stiffness controlled test procedures performed with servo-controlled shear systems are the most versatile for simulating the wide range of boundary conditions expected in nature. Examples of a function controlled procedure in addition to dilatation controlled procedures are discussed for different characteristic behaviours. ZUSAMMENFASSUNG: Steifigkeitskontrollierte Scherversuche mit servohydraulischer Steuerung eignen sich gut unterschiedliche Bettungen, wie auch in der Natur vorkommen, zu simulieren. Beispiele für spezielle Steuerungsfunktionen und dilatationsgesteuerte Prozeduren mit verschiedenen charakteristischen Eigenschaften werden diskutiert. RESUMÉ: La rigidité a commandé des méthodes d'essai exécutées avec les systèmes asservis de cisaillement sont la plus souple pour simuler l'éventail d'états de frontière prévus en nature. Des exemples d'un procédé commandé par fonction en plus des procédures commandées par dilatation sont discutés pour différents comportements caractéristiques.

Jan 1, 2003

By P. E. Venteer

The Grootegeluk coal-processing plant treats 3 kt of raw coal per hour to produce a middlings fuel coal and a coking coal fraction with ash contents of 35 and 10 per cent respectively. The plus 0,5 mm fraction is treated by heavy-medium processes, the final top size of the coal being 15 mm. About 400 t of minus 0,5 mm coal per hour is subjected to froth flotation. The routes originally considered for the processing of this fine coal were froth flotation, shaking tables, heavy-medium cyclones, and water only cyclones in combination with froth flotation. The results from tests on the fines arising from a small-trial open-cast mine are discussed. When the froth flotation route was decided upon, further tests were conducted on the selection of the equipment most suited to the particular requirements of this coal and the rest of the plant. Tests using different types of flotation cells and dewatering equipment are discussed. During the commissioning, several operational problems were encountered, and the work done to find the best solutions is discussed.

Jan 1, 1984

By I. V. Samarasekera, E. B. Hawbolt

A review of recent work being conducted at the university of British Columbia on the modeling of the microstructural evolution during the hot rolling of steel is presented. A mathematical model of heat transfer was developed to describe the thermal field in a slab during rough and finish rolling. The model for rough rolling, discussed in this review, also simulates the growth of oxide scale on the slab surface. To quantify the heat transferred from the slab to the work rolls, instrumented samples of MSI3O4 L stainless steel, 0,05 per cent carbon steel, and 0,05 per cent carbon steel with 0,025 per cent

Jan 1, 1995

By J. H. Dalton

The paper reviews the effects of fast-neutron irradiation on the tensile properties of austenitic stainless steels at irradiation temperatures of less than 400°C, using, as an example, work carried out at Pelindaba on an AISI 316 type steel produced in South Africa. Damage produced in these steels at higher irradiation temperatures and fluences is also briefly discussed. The paper concludes with a discussion of some methods of overcoming or decreasing the effects of irradiation damage.

Jan 1, 1979

The aspect ratio (mill diameter/mill length) of autogenous and semi autogenous mills varies widely and can be as high as three or as low as 0.5. The literature on the subject of what effect aspect ratio has on grinding mill performance or energy efficiency is almost non-existent. However, at the design stage of many grinding circuits the subject is often vigorously debated amongst metallurgists. In this paper the performance characteristics of mills with different aspect ratios are examined to determine whether process performance characteristics are a function of aspect ratio and whether high aspect ratio mills are any more or less energy efficient than low aspect ratio units. Data from both pilot and full-scale mills are used for this purpose in open and closed circuit configurations.

Jan 1, 2007

By A. Chryss, L. Pullum

Shear-thickening suspensions abound throughout the hydraulic conveying industry; at least this is the perception of many engineers running plants where hydraulic conveying is commonplace. In reality, shear thickening behaviour is limited, in the main, to high concentrations of fine particles, including colloidal and biological suspensions, at moderate to high shear rates. In the authors? experience most cases of shear-thickening behaviour have been either simple ?coarse? particle interactions, poor instrumentation techniques, or both. In some cases these were obviously heterogeneous flows, while in others flows that were homogenous, or were thought to be homogenous. Examples, which illustrate this erroneous perception are given. However, the trend towards pastes and complex suspensions that use high concentration carrier fluids means that the underlying slurries for many of these flows may now be truly shear-thickening. Unfortunately, suspensions that might exhibit shear thickening also invariably exhibit slip, or wall-particle depletion. These separate phenomena are difficult to resolve experimentally and many observations of apparent shear-thickening behaviour are in fact obscured or convoluted by slip effects. A method is presented whereby the true flow properties of these high concentration suspensions, and hence accurate prediction of pipeline flows, can be made using a parallel plate rheometer.

Jan 1, 2007

Proceedings of the Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry, Montreal, June 1970. The Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry was sponsored by The Canadian Institute of Mining and Metallurgy, McGill University and Ecole Poly technique. The programme included 71 papers on various topics, as follows: Market Analysis and Logistics Planning; Quantification of Geological Variables; Blending; Capital Investment Decisions; Mining; Financial and Economic Analysis; Search for Mineral Deposits; Market Forecasting and Strategies; Operations Research in Process Modelling; Ore Reserve Estimation; Management Information Systems; Optimization and Control of Mineral Processes. In addition to general sessions, a special feature of the Symposium was Executives' Day, which was held to provide top and middle management with a broad understanding of the usefulness of decision-making techniques and their role in the mining organization. Panel Discussions and two keynote speakers provided a review, in non-technical terms, of the areas in which decision-making techniques have proven valuable. The present volume contains 65 papers submitted for publication, along with a complete account of the Executives' Day discussion. It is broadly divided according to the above subject headings. Approximately 550 pages, illustrated. Price: $15.00; $12.00 to students, plus 50 cents for handling costs. Order now from CIM headquarters: Canadian Institute of Mining and Metallurgy, 906-1117 Ste. Catherine St. W. Montreal 110, Quebec.