Search Documents

By J. D. Steenkamp

Southern Africa has a history rich in the pyrometallurgical processing of ores. Two of the alloys produced are high-carbon ferromanganese (74?83 per cent Mn) and silicomanganese (59?67 per cent Mn and 14?31 per cent Si). The largest land-based manganese ore deposit in the world is based in the Northern Cape Province of South Africa. In 2010, 6.3 Mt of ore from the deposit was exported, mainly to China, Norway, Japan, and India, and an estimated 1.1 Mt beneficiated locally to produce manganese ferroalloys. In southern Africa the producers of manganese ferroalloys are Metalloys and Assmang, and of silicomanganese Transalloys, Mogale Alloys, and Match Corporation. Submerged arc furnace technology is utilized in the production of high-carbon ferromanganese (HCFeMn) and silicomanganese, applying the discard slag practice in both instances. The carbon content of HCFeMn is reduced using converter technology and that of SiMn using the Perrin process. Ninety per cent of the world?s manganese ferroalloys production is consumed by the steel industry. The consumption (and production) of manganese ferroalloys therefore closely follows worldwide steel production. From 2001 to 2010, the doubling of the worldwide production of manganese ferroalloys can be attributed to an increase in production capacity in Asia and Oceania, with the largest increase in the production of SiMn. Manganese ferroalloys produced in Asia and Oceania are mainly for the local market, with North America, Europe, Russia, and Turkey the major markets for alloys from southern Africa. The major challenges faced by the southern African manganese ferroalloy producers are increasing electricity tariffs and productivity of labour, which require a concerted effort by all parties involved to achieve a satisfactory solution. Keywords manganese ferroalloys, ferromanganese, silicomanganese, southern Africa, South Africa, manganese ore, high-carbon ferromanganese, refined ferromanganese, refined silicomanganese.

Aug 1, 2013

By G. M. J. van Heerden

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Union Section of Anglo Platinum is situated ±18 km west of the town of Northam on the north-western rim of the Bushveld Igneous Complex. Both the Merensky and UG2 reefs are mined. Support of the Merensky stoping areas with rock bolts is specifically problematic due to the stoping width restrictions varying around 90 cm. The installation equipment of in-stope rock bolts and the effectiveness thereof in the Merensky stoping areas was critically evaluated. In order to do this a background research on the need for better on-the-face support had to be conducted. The need for improving the rock bolt drilling and the equipment had to be investigated and the financial implications and justifications for the improved equipment examined. To conduct the search an overall study was done on the rockfalls and safety aspects throughout the platinum industry in South Africa and specifically Union Section. It was found that most of the rock falls in the Merensky stoping areas of which ± 70% are less than 1.2 m in thickness generally occurs within 4 m from the face and causes ± 60% of the in-stope injuries. Serious shortcomings had been identified with respect to the airleg, rock drill machine and the drill steels used in the drilling of the rock bolt holes. Through experimentation, using a testing frame built for this purpose on surface and with the co-operation of mine staff and suppliers, a number of possible modifications were identified and tested. This resulted in the final product with which it was possible to drill a 1.2 m hole in the hangingwall of the stopes ranging with an angle to the hanging from 90° for a 90 cm stoping width and 67° for a 80 cm stoping width. It is confidently concluded that this system will effectively improve the total face support and result in a substantial reduction of rock falls and consequently the occurrence of injuries and fatalities in the Merensky stoping areas. The installation of rock bolts on the face with the modified drilling equipment will increase the direct support, but the system has a potential of a substantial reduction in the profile stick support density and an increase in productivity in the stoping areas due to fewer occurrences of rock falls. It was finally concluded that effective modifications to the drilling equipment for rock bolt in-hole drilling could be made and the installation thereof in the stope face is adequately justified.

Jan 1, 2002

Geologists in some underground gold mines collect grab samples from broken ore piles or trucks as a method of grade control. It is often known as muck sampling. Generally, the goal of grab sampling is to try and reconcile the mined grade at the ore source to the predicted grade and/or predict the mill feed grade. The mass of the sample collected is limited by health and safety issues, as well as by the capacity of the laboratory to process the samples within a given time frame. In general terms, grab sampling is known to be problematic because samplers tend to oversample the fines, and/or pick out high-grade fragments; surface sampling of piles does not test material within the pile; muck piles in development drives/faces are likely to be zoned due to the blasting sequence; high or low-grade material may preferentially segregate in the pile during mucking; the five per cent mass reject size of the material in muck piles is very large from underground blasting; some correlation usually exists whereby the larger fragments are enriched or depleted in the critical component of value; and the average error made in estimating the true stockpile grade is likely to be high. The method is prone to chronic fundamental sampling, grouping and segregation, delimitation, and extraction errors. Substantial warnings must be given about the use of grab sampling for grade control in gold mines. The method may appear to work sometimes, which can be attributed to a fine gold particle sizing and more disseminated distribution. As with all sampling methods, its appropriateness must be determined by ore characterization and heterogeneity testing to ensure the method suits the ore type.

Jan 1, 2010

By Godofredo F. Barrios

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings from as fine as 100 microns and coarser have been used. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies which allow an end user to consider urethane screen surfaces for fine screening applications. These technologies allow an end user to use the inherent advantages of urethane with regards to wear resistance while also realizing the benefits that a high oper area urethane screen surface can bring. These benefits include non blinding characteristics and feed capacities that which rival that of traditional stainless steel surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines they are used in conjunction with. There will also be a presentation of case studies of commercial installations where these technologies are utilized. These case studies are from the base metals industry therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints which must be taken into account when considering urethane screen surfaces such as temperature and chemical attacks. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By M. F. van der Merwe

Anglogold Ashanti?s Kopanang Gold Plant (previously No. 9 Gold Plant) treats ore from Kopanang and Tau Lekoa shafts. The plant is twin streamed and has dedicated treatment circuits, from milling to final product, for each shaft. Waste rock material is used to compensate for the mill gap on both streams. Each stream consists of three 4.85 m x9.15 m ROM mills in closed circuit with a single stage hydrocyclone, milling an average of 7 000 t per day. The liner configuration in each mill consists of six rows of 30 grid liners along with rectangular lifter bars. The topic of gold lock-up is not new and has been investigated and reported on many times, both within Anglogold Ashanti and the broader mining industry. Although the lock-up mechanism is understood, its measurement is neither practical nor precise. The initial lock-up in a new liner and the release as the liner wears down cannot be accurately quantified. Previous test work carried out on Kopanang Gold Plant (with a ?gold scanner?) measured the natural gamma radiation emitted by uranium. This radiation is in proportion to the mass of concentrate locked up in the grid liner pockets, as well as between the cast-on backing plate and the shell. The ratio of concentrate lock-up was estimated as 35% behind the liners and65% in the pockets. Mill gravity concentrates are recovered during routine relining operations from behind the grid liners at Kopanang Gold Plant. Prior to relining, the liners tend to release the concentrate from the pockets as the liners wear. Historical Kopanang data from actual ?mill gold? smelted indicates that an average of 29 kg gold is recovered from behind each row. This indicates a total lock-up of 250kg gold per mill. This locked-up gold should preferably be minimizedor eliminated for the following reasons: ?The cyclic build-up and release of gold in mills complicates accounting ?Gold concentrate arising from liners is a security risk and creates a major mechanism for gold theft ?Loss of interest on the value of 250 kg fine gold is significant and was a major driver for the project. These factors led to the need to develop techniques to eliminate or at least minimize the gold lock-up in the mills. Wave liners, with rubber inserts, have been successful in eliminating lock-up, and were tested at Kopanang Gold Plant in November 2000. However, due to increased load-slip and high wear rates associated with these liners, this option proved less economical in terms of liner wear. Grid liners, with rubber-filled pockets, demonstrated a very high wear life and eliminated pocket lock-up. This system was successfully trialed in January 2003, but unfortunately did not prevent lock-up behind the liners. Current developments have resulted in a system that eliminates both pocket and backing plate lock-up. The conventional grid liner design has been modified to remove its steel backing plate. Rubber inserts that are integrated onto a rubber backing plate, have been designed to be used with the newly modified grid. The backing plate and grid pockets are now completely occupied by rubber, thus completely eliminating concentrate build-up around the new grid liner system installed in November 2003. Results to date are promising and liner life is expected to exceed conventional performance.

Jan 1, 2005

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

By Y. M. Zhao

The separating performance of a pilot dry beneficiation system using a gas-solid fluidized bed was investigated with coal from South Africa. The coal used for the study has a low inherent moisture content, a moderate ash content, a moderate volatile content, a low sulphur content and a high calorific value. Its washability is moderate. Experimental results show that the separating quality of the fluidized bed drops gradually as the feed-coal particle size decreases. The probable error, E, values for 50?25mm, 25?13 mm and 13?6 mm coals were 0.04 g/cm3, 0.06 g/cm3 and 0.09 g/cm3, respectively. The cause of the differences in separating characteristics was analysed by particle dynamics and numerical modelling. Furthermore, the pilot fluidized bed was employed to separate 50-6mm coal. In this experiment the coal ash content was reduced from 23.74% to 11.79%, with a probable error, E, value of 0.07 g/cm3and a recovery efficiency of 98.26%. This indicates that the fluidized bed is applicable to the separation of coal from South Africa and has good separating performance and wide applicability. Keywords: feed-coal particle size; gas-solid fluidized bed; dry coal beneficiation; numerical simulation.

Jan 1, 2010

By H. Zhu

Coal desulphurization by flotation is often difficult due to the surface oxidation of coal pyrite. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were adopted to obtain detailed information about the surface oxidation of pyrite. Fresh pyrite surfaces were found to be hydrophilic, and to turn hydrophobic after initial oxidation, with oxidized products such as polysulphide FeSx and free sulphur. The oxidized products on the pyrite surface were reduced by an electrochemical method, returning the surfaces to a hydrophilic state and thus increasing the separating efficiency of coal from pyrite by flotation. Key words: surface oxidation, pyrite, SEM, XRD pattern, electrochemical modification.

Jan 1, 2002

By B. C. Viljoen

"SynopsisCommencement of the next phase of the Lesotho Highlands Water Project is a year or so away from becoming reality. Some 50 km of tunnels in the form of access adits, shafts, diversion tunnels, and main waterways will be constructed. Sprayed concrete will form an integral part of the temporary and permanent rock support systems that will be installed. Furthermore, the use of sprayed concrete as a final tunnel lining solution was proposed as a viable alternative to concrete linings in the feasibility studies that preceded the forthcoming implementation phase.The aim of this paper is to make the reader aware of all the sprayed concrete related issues that engineers tend to grapple with during the design and construction of tunnel projects and other underground works. Primarily, these issues would include selection of applicable design parameters, technical specifications, construction application methods, quality control and, most importantly in the context of final or permanent linings, the durability of sprayed concrete.The International Tunnelling Association (ITA) Working Group (WG) 12 has been tasked specifically to publish a set of recommendations on the Quality and Control of the Application of Sprayed Concrete and the Testing of Sprayed Concrete for Durability. These tasks were also further explored at the recent World Tunnel Congress (WTC 2015) that was held in Dubrovnik, Croatia at the end of May 2015.IntroductionSprayed concrete is presented in a variety of shapes, designs, forms, application methods and accompanying terminologies including shotcrete, gunite, pneumatically applied concrete, and the like. The International Tunnelling Association (ITA) decided to standardize on a single terminology, namely ‘sprayed concrete’, in order to simplify specification, interpretation of guidelines, and codes of practice."

Jan 1, 2015

By M. J. Voigt, R. A. Govender, A. Mainza, L. Bbosa

"Mineral texture is a critical factor which controls ore variability and is an important attribute in geometallurgy. In relation to downstream processes, it affects the fracture pattern during breakage, where rock strength is inherently a function of mineral texture. Because of the subjective nature of mineral texture, it has not been easy to quantify, especially in the context of a measurement suitable for use in geometallurgical programmes. The aim of this paper is to present the first steps in developing a 3D mineral texture quantification method for drill core and to assess its sensitivity to differences in rock strength using a case study. The methodology includes classifying the textural information using the 3D grey level co-occurrence matrices (GLCM) and X-ray computed tomography (XCT) coupled method. Rock strength tests were performed using the split Hopkinson pressure bar (SHPB). The case study investigates a heterogeneous polymetallic sulphide deposit and a homogeneous shale subdivided into three ’mineral textural types’. The variability is largely captured by the GLCM matrices, and preliminary trends can be observed where the shale is finer grained and has a higher yield strength in comparison with the coarser grained polymetallic sulphide ore. IntroductionModern mining requires the exploitation of lower grade and more complex, heterogeneous orebodies to address the growing industry demands. Historically, processing plants were designed and built based on average ore characteristics and therefore are relatively inflexible when facing the full spectrum of ore variability in heterogeneous orebodies (Lamberg, 2011; Lotter, 2011; Schouwstra et al., 2013). The practice of geometallurgy represents an opportunity to manage ore variability in the mining industry (Powell 2013; Baum, 2014; Yildirim et al., 2014; Nguyen, 2013). It focuses on quantifying the relationships between ore characteristics and their downstream mining and processing responses, often starting with small-scale laboratory testing. The purpose of geometallurgy is linked to maximizing the net present value (NPV) of an orebody by minimizing technical and operational risk – where ‘ore variability’ is considered one of the most significant technical risks."

Apr 1, 2019

By M. Stephton, L. A. Cornish, R. Süss, N. B. Maledi, J. H. Potgieter, L. Chown

In today?s gas turbines, the emphasis is on saving energy and reducing the amounts of pollutants emitted. This can be attained only by designing alloys with higher melting points and the capability to retain mechanical integrity at increased temperatures. The development of nickel-based superalloys (NBSAs) has reached its limit, as the alloys are operating at critical temperatures close to their melting points. Further increase in the operating temperatures will result in dissolution of the strengthening phases and even melting. Recent trends are towards developing materials that are adequately strong but have much higher melting points and corrosion resistance than the NBSAs that are currently in use. Studies conducted on Pt alloys with similar structure to the NBSAs have presented mechanical results that are promising. This has led to further development of these alloys as a replacement for NBSAs. The operations of gas turbines are usually limited by hot corrosion, which could lead to catastrophic failures. Increased temperatures have an adverse effect on the corrosion of the alloys by making the environment more aggressive. Hence, during a material selection process, the corrosion behaviour of any selected material for a highly specialized application such as gas turbines needs to be assessed. Generally, coatings are applied to combat degradation by salt deposits, hence coated and uncoated NBSAs were selected as benchmark alloys. Corrosion mechanisms and kinetic studies of the Pt alloys were conducted. High temperature hot corrosion (HTHC) tests were conducted at 950°C for540 hours. Analysis of the corrosion products was conducted using a Raman spectrometer, scanning electron microscope with energy dispersive X-ray spectroscopy (EDS) optical microscopy, and X-ray diffraction study of the phases that formed. Both coated and uncoated NBSAs failed under the test conditions. Samples were covered with a porous non-adherent greenish layer which is characteristic of NiO. Pt alloys displayed superior corrosion properties compared with the benchmark alloys.

Jan 1, 2006

By A. S. Macfarlane

Mineral resource management (MRM) practice has developed in South Africa over the course of the last ten years, with the purpose of integrating previously isolated technical functions into a value chain aligned, process organization, responsible for mine planning and optimization. The implementation of MRM within various companies has met with varying degrees of success, often resulting in incremental improvements in the planning process and, conversely, often becoming the scapegoat for poor delivery on plans and projects. The reason for this has been, amongst others, a lack of a suitable metric to define the success rate of MRM in the business at hand, in terms of its contribution to the bottom line. This paper is the result of extensive research by the author into this subject, which has resulted in the conclusion that economic value added is an appropriate measure that will lead to real optimization and value creation in mining companies, if applied within a new, holistic model

Jan 1, 2006

By R. J. Durrheim

The seismicity of the Witwatersrand Basin and Bushveld Complex has been analysed, revealing significant differences in source and damage mechanisms. A comparison of mining taking place at similar depths and extraction ratios indicates that the seismic energy release rate is considerably lower in the Bushveld Complex. Technologies introduced in the past decade to manage the risk of rockbursting are reviewed and assessed. These include geophysical methods to detect hazardous structures ahead of mining, new mining layouts and support systems, and the mechanization of in-stope processes. Despite important differences in geology, in situ stress, mining layouts and methods, there are many opportunities for the reciprocal transfer of knowledge, experience and technology between the gold and platinum mining sectors to improve the management of the rockburst risk.

Jan 1, 2005

By J. Kempken, T. A. Schreiter, R. Degel, H. Schmieden

Keywords: Pyrometallurgy, SMS Demag, Germany, submerged arc furnace, ferro alloys, non-ferrous, FeCr, FeNi, FeMn, copper, cobalt, slag cleaning, PGM, rectangular furnace After a short summary of the SMS Metallurgy part of the SMS group, the paper will focus on Submerged Arc furnace technology. After general aspects of furnace design, the focus will shift to different applications and their specific furnace requirements. Finally, a state-of-the-art design tool as well as a new invention to improve slag-cleaning technology will be featured.

Jan 1, 2006

In today?s high tech world, systems are getting bigger, faster, better. To remain at the leading edge, in any business, depends on accurate but flexible design thereby allowing operational managers to provide alternatives to improve their operations. The ultimate goal is to deliver to plan, with optimum economics. Mining is no different, with falling prices and escalating costs, improved margins become the focal objective. There are many ways to achieve this, ranging from operational efficiency improvements through production scenarios to planning initiatives. Of all, planning usually receives the least attention, yet it is the area of most influence on the NPV of the reserve. With computer technology, numerous concepts and iterations are possible thereby closing the gap between optimal and actual design. This paper discusses the application of the split shell design at the De Beers Venetia open pit in South Africa.

Jan 1, 2001

By L. A. Cornish, L. H. Chown, M. Matema, R. Süss, L. Glaner, A. Douglas

Mintek has been developing Pt-based alloys for high temperature applications in aggressive environments, for example, land-based turbine engines, to replace the currently used nickel-based superalloys (NBSAs). The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert and has a higher melting point, the Pt-based alloys can potentially be used at higher temperatures. The greater chemical inertness of the Pt-based alloys compared to the NBSAs means that coatings can be simpler, or perhaps not even used at all, depending on the environment. TEM work was done at NIMS, Japan, to investigate the changes in the microstructure o f Pt-Al and Pt-Al-Ir alloys at elevated temperatures using in-situheating up to1100°C. Initial casting trials showed that work needs to be done to optimise casting parameters before commercialisation can take place. Room temperature tensile tests were performed and results were variable mainly due to microstructural differences. The alloy hardnesses were in the order of 300-350HV with ultimate tensile strengths of ~800 MPa and elongations of less than 10%. These results are comparable to other alloys used at high temperatures, which is very encouraging. Keywords: platinum, super alloys, hardness, tensile

Jan 1, 2006

By L. du Preez, J. D. Steenkamp

This paper introduces the concept of clean steel production from a pyrometallurgist’s perspective to the broader metallurgical community. A simplistic overview of the steelmaking process from iron ore to car body manufacturing is followed by an introduction to the South African steel industry and the technologies that it utilizes. The process is illustrated by an overview of the flow sheet and technologies for the production of clean steel at Saldanha Steel, South Africa.

Jan 1, 2015

By M. Olper

The change in regulations and the strong attention to the environment have suggested some changes in the traditional processes for the recycling of lead acid batteries. Engitec Technologies, marketing the Integrated CX® System, is continuously updating and improving its technology to fulfil the technical, economical and ecological requirements coming from the market and from the environmental authorities. In this paper Engitec Technologies will present the latest technical innovations introduced in the Integrated CX® System.

Jan 1, 2008

By L. J. Gardner

Ore pass systems play a critical role in moving broken rock from the workplace to surface, and the integrity of the ore pass excavations is crucial. Over the life of the mine, ore pass integrity deteriorates, which may eventually result in the ore pass no longer being fit for purpose. This paper presents several case studies of successful ore pass rehabilitation exercises.

Jan 1, 2006