Search Documents

By C. Sampaio, C. Petter, M. Veras

"INTRODUCTION Use of sensor technology applied to the gravimetric beneficiation is intended for the selective preconcentration or separation of various minerals. Sensor Based Sorting (SBS) uses sensors to identify the particles and separate them by a mechanical process (flap) or pneumatic ejection valves (Wotruba et al. 2014). The principle of the SBS technology to separate mineral particles consists of three phases which cover feed,detection and separation. (killmann, 2009 Apud nienhaus et al. 2014). The applicability of the technique in an early stage of beneficiation enables free particles and poor grade to be a part of the process. The mass of tailings to be processed can be removed at the initial stage to save energy, water and equipment maintenance (Wotruba et al. 2014). Lindner (2010) suggested that the use of SBS technology would only will be possible if there exsists an electromagnetic interaction in all the wave spectra interacting with the solid ore. The interaction of electromagnetic waves depends directly on the characteristics of the material. The material receives a spectrum of electromagnetic waves by irradiation and this results in a reduced wavelength with differing types radiation such as fluorescence, reflection, remission, absorption, transmission and transmission. The frequency of the wave spectrum varies between 1000 and 1020Hz, illustrated by the data in Figure 1, which shows that each type of sensor emits a wavelength inversely proportional to the frequency ranging from 10-11pm to 104km, and the frequency that varies between EHz 103 and 1020kHz. The difference between the electromagnetic spectrum variations can only be visible to the human eye at wavelengths with intervals between 380nm and 780nm (Wotruba et al. 2014). One of the main advantages of operating with imaging sensors is the versatility of the images which can take on zero, one, two or three dimensions shown below as a point, a line, an area or a spatial image, as illustrated in Figure 2. According to Schubert (1988), to separate a mineral particle it is necessary to follow the characteristics of mineralogy, physics and chemistry with or without use of water. The use of new technologies can help reduce operating costs and improve utilization of mineral resources."

Jan 1, 2016

"When boring a tunnel, homogeneous hard rock is the exception rather than the rule. While contractors can set goals such as meters per month and performance incentives, it is also prudent to plan for difficult ground. A properly designed tunnel boring machine (TBM) can tackle fault zones, water inflows, squeezing ground, or whatever the risk may be. The alternative is not a good one: modifying the machine in the tunnel after bad ground is encountered. Not only does this result in increased downtime, but it also needlessly exposes the crew to the tunnel conditions. In the worst case scenario, the entire operation grinds to a halt.However, an accurate GBR cannot always be obtained, particularly for mountainous, high cover tunnels in remote locations. And even with a thorough GBR, unforeseen geological events can occur. What can be done in these situations? Difficult Ground Solutions (DGS) is ground investigation system with a suite of options that can be added to a shielded hard rock machine or dual-mode, Crossover machine to better enable advance when conditions are unknown or difficult conditions are anticipated.DGS consists of a set of integrated features tailored to a specific project’s geology. The main components of the system allow for ground investigation ahead of the TBM, increased monitoring and methods to keep a machine shield from becoming stuck.In fault zones and squeezing groundIf fault zones or squeezing ground are known or suspected, or if there is even a possibility of encountering them, this can greatly affect the TBM operation. Shielded machines protect the crew from the surrounding rock, and they can bore and line a tunnel efficiently, but in fault zones and converging material their shields can be their downfall. Avoiding a stuck machine is paramount to project success. DGS employs several features to avoid the problem of a machine becoming stuck. The first of these is multi-speed cutterhead drives. These drives effectively give the machine multiple modes of operation—high speed, low torque for hard rock, and low speed, high torque for difficult ground. Designing a machine with high-torque, continuous boring capabilities allows that machine’s cutterhead to restart with break-out torque in difficult ground. The net effect is that the machine can keep boring in the event of a face collapse and can bore through fault zones and running ground where the potential for cutterhead jamming exists. Going one step further, multi-speed gearboxes give the machine the ideal earth pressure balance- (EPB-) type torque if larger sections of soft ground are anticipated.Secondly, TBMs can get through squeezing ground and faults using Continuous Shield Advance. This design utilizes a stepped shield configuration — where each successive shield is slightly smaller in diameter — to avoid becoming stuck in converging ground. External shield lubrication is an added insurance against becoming stuck, using a series of radial ports that can pump Bentonite into the annular space to act as a lubricant in squeezing material.As a last effort, if a machine has already become stuck the TBM can utilize augmented, or “super” thrust. Additional thrust jacks can be added to supply an extra boost in a short stroke, generating enough force to break loose a trapped shield."

Jan 12, 2017

By Regis F. Kopac

With the growing dependence on coal as an energy source, finding a means to prevent or reduce the freezing of coal during winter shipment has become increasingly important. Several chemical companies focused on this problem and applied chemical technology to develop suitable solutions. As a result, a number of freeze conditioning agents have been introduced in the past few years, several of which have been highly effective in controlling frozen coal. The efficacy of these chemicals has been well established, however many users have found that only a well defined program will produce acceptable results at a reasonable cost. Positive program results yielding recognizable benefits have caused many power generating and coking plants to consider freeze conditioning agents. A freeze conditioning agent (or FCA) has been defined as a multi-component organic liquid designed to be sprayed on coal particles at bulk shipping points to assure that receiving locations will be able to unload, store and use the treated coal with minimum delay or inconvenience. The chemicals are generally applied at rates of 1 to 2 pints (0.473 to 0.946 liters) per ton and normally function by changing the crystalline structure of water left on the coal during processing. The bond strength of the ice that may subsequently form is markedly reduced. Instead of freezing into solid, unmanageable masses, the coal can be easily unloaded by rotary dumping or the opening of hopper car doors.

Jan 1, 1980

By G. Belardi, G. Marruzzo, P. Plescia

This paper presents the results of grinding tests performed on magnetite from Kiruna (Sweden) and on chromite from Skoumtza (Macedonia. Greece). Stresses were measured by XRD, which determined the variations in the characteristic structural spacings of the minerals both before and after, grinding in a HSM/250 Herzog laboratory ring mill. Anal Isis of the magnetite and c hromite crystallinstallin was performed hi measuring the broadening of the strongest diffraction peak (311). .Also, structural analysis on chromite was carried out using the Mikheev model. Ultrafine-grinding tests on the magnetite and chomite demonstrated that this type of treatment can induce profound variations m the surface-stress state. These included plastic variations of the cell followed by "chemical" stress with oxidation front the stricture to form hydroxide or carbonate, films. This can have a great influence on the mineral reactivity to flotation reagents

Jan 1, 1996

By St. Mergentime, K. Zeidler, V. Gall

2001, the New Jersey Transit Authority commissioned the JV Merco-Obayashi with the rehabilitation contract of the approximately 130-year-old, 4,200 ft long, partially brick- lined Bergen North Tunnel. The contract entailed the tunnel enlargement, shotcrete and rock dowels initial support according to the NATM, a waterproofing system, tunnel drainage and a cast-in-place concrete lining. The rock conditions encountered required design adaptations and significant modifications of the initial tunnel support. Flexibility, skill and extensive experience on the Authority’s and Contractor’s side finally lead to a success. This paper describes the operations and design modifications carried out.

Jan 1, 2003

By Wallace Jarman

Introduction As with many gravity concentration processes, pneumatic concen¬tration traces its origin in antiquity. The use of winnowing to separate chaff from grain has long been known, and such procedures were undoubtedly practiced in ancient civilizations for the concentration of ores and the separation of slag from metal whenever specific gravity, size, and shape differences were favorable. Taggart142 has reported on the use of dry rockers and dry panning techniques for use with gold ores in arid regions such as Western Australia. The present day air table was developed in the last century for this purpose. Devices and Processes Classification. All classifiers make a separation on the basis of size, shape, and specific gravity. In addition to specific gravity and size, particle shape factor is often particularly important to pneumatic processes, and advantage is taken of the fact that both flat and fibrous particles settle at velocities substantially lower than that of their equiv¬alent spheres. Another factor of importance in this process is the bulk density of the material since substances such as exfoliated ver¬miculite or partially opened fibrils of asbestos have bulk densities significantly lower than those of the pure in situ mineral. Winnowing takes advantage of all of these physical factors to affect a separation starting with a closely sized feed, and vermiculite has been separated from rock by this process.142 When air classifiers are used to size minerals, the separation will often not be perfect because heavy particles will respond similarly to somewhat coarser light particles while flat, elongated, and low bulk density particles will act as would particles finer than the cut size. An example of a classification process that also results in concentration is the zig-zag classifier"' used to separate paper from glass, metal bottles, and cans during the recycle of municipal solid waste. Application of this process to minerals showing the proper specific gravity, size, and shape differ¬ences is obvious. An important device of this type is an air-aspirated screen used to remove asbestos from its associated rock during the dry processing of that mineral.144 The raw ore is crushed and screened and the asbes¬tos removed by aspiration from the surface of the screen by virtue of its shape and low bulk density. Hindered Settling. Based on the discussion in the section on "Hindered Settling Concentration and Jigging," the use of air devices could be anticipated in desert areas or where moisture may be deleteri¬ous to the product to be separated. Such processes have three major defects: (1) dust may be difficult to contain, (2) fines are difficult to process, and (3) the process is inherently less efficient than are wet processes as may be seen from Eqs. 3 and 4 in the section on "Hindered Settling Concentration and Jigging p. 4-47." Taggart142 has reported on the use of both dry panning and a dry rocker for gold separation in and regions. The dry panning makes use of winnowing, defection on the basis of specific gravity and shape during fall, and hindered settling. Prescreened placer material is poured from one pan to another as air blows across the falling stream. The process is repeated many times with hand picking to produce a rough concentrate. Magnetic minerals are then removed, and the residue, one grain deep in the pan, is air blown. In dry rocking the gravel is sized on a steeply inclined screen with the undersize fed to a riffle box with a porous bottom which is blown from underneath."' This device was the forerunner of the present-day air table. Air Tables and Jigs.145. 146 At least nine types of these devices have been developed, all but two of them for coal. While the devices used for coal may be characterized as pneumatic jigs, pneumatic tables, and pneumatic landers,145 only pneumatic jigs survive today. The same is true for ores.'" In these devices presized particles are fed to the separator which consists of an inclined vibrating conveyor with a porous surface through which air is carefully introduced to form a fluid bed. The lighter particles are lifted by the air out of uphill conveyance and float downhill, while the heavier particles in contact with the surface are conveyed uphill by the vibrator. Typically both transverse and longitudinal slopes are used. A plan view of a Triple S air table and the type of separation made is shown in Fig. 44.147 Because of its external appearance, the device has been called an air table, although it functions essentially as a jig. However, some of the asymetrical acceleration conveying function of a standard shak¬ing table is also performed by the eccentric vibrator incorporated into this device. Low pressure air is admitted below the vibrating table surface consisting of cloth (e.g., canvas), porous plastic, woven wire, or punched metal supported on a wire mesh or grid. As with a shaking table, the device produces a concentrate, middlings, and tailings. The middlings are recycled or are subsequently treated on another concentrating device. As with many wet separations, presizing by screening is necessary. The oft-repeated admonition of Professor Richards, "Separation without classification is damnation," is cer¬tainly true here. In this way a small heavy particle which might weigh the same as a large light particle and thus report to the same place on the air table has already been removed in the sizing step. Air tables are almost universally encased with a canopy to remove dust by aspiration. Some concentration may also be achieved in this step when favorable specific gravity, size, and shape differences are present. Applications Ore Separations. Air tables were originally developed for ore separations, and they find application in and regions or where water is deleterious or inconvenient to use or remove (e.g., small tonnage materials already dried). They have been used for asbestos, bauxite, calcite, cassiterite, columbite-tentalite, diatomaceous earth, fluorite, gilsonite, graphite, kyanite, manganese minerals, mica, managite, perlite, pyrite, pyrrhotite, vermiculite, and uraninite ores. More recently, air tables have found favor in separating a wide variety of secondary materials such as abrasive grains, bone char, catalysts, fiberglass, scrap glass, scrap wire from its insulation, prills from slag, dross and coke from metal or from each other, metal from crushed crucibles, lead from plastic in old batteries, and cubic particles from flat ones. The devices also finds considerable application in the preparation of food¬stuffs. As stated before close sizing before separation is desirable, and if the specific gravity difference is slight, very tight

Jan 1, 1985

By K. G. Colman

Este texto intenta facilitar al operador y contratista 10s datos básicos para dimensionar las cribas vibrantes que deban ser utilizadas en las plantas de trituración. Las capacidades básicas, factores que la modifican .... etc., utilizados en el cálculo de la superficie requerida, se han desarrollado empíricamente y modificados sus valores hasta el presente con 10s datos de las aplicaciones prácticas Hay que señalar que el cribado tiene mucho más de arte que de ciencia exacta; sin em- bargo, la información aquí presentada proporciona una razonable seguridad cuando se aplica al cálculo de cribado de minerales metálicos.

Jan 1, 1982

By J. L. Huiatt, D. G. Foot, J. D. McKay

The US Bureau of Mines compared column flotation using either fine or coarse bubbles with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a &.7% Cr2O3-grade rougher concentrate with 87% recovery, compared with 43.8% and 43.5% Cr2O3-grade rougher concentrates with 85% and 77% recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse- and fine-bubble column flotation produced rougher concentrates containing approximately 41.5% Cr2O3 with 95% recovery, exceeding conventional flotation, which produced 35.6% Cr2O3 -grade concentrates with 87% recovery.

Jan 1, 1987

By T. C. Rao, Vanangamudi. M., J. P. Barnwal

Experiments were carried out on 76 mm laboratory heavy medium cyclone treating -2.0 t 0.5 mm coal and on two 600 mm industrial heavy medium cyclones treating coal in the size range -13.0 t 0.5 mm. The variables studied were spigot diameter and feed medium gravity. The generalised distribution curve for the separation of coal in these heavy medium cyclones has been defined by the equation [ ] The specific gravity of separation SG has been found to increase linearly with increase in feed medium, gravity (SGf). The relationship for SG of industrial cyclone is given as 50 SG = -6.801 t 6.463 SGf t 0.0327 Spig 50 -0.02625 SGf. Spig. Further, the probable error for the separation has been found to be linearly related to (SG50 - SGf ) according to the equation [ ] The model equations developed have been used to select appropriate levels of operating conditions to achieve an increase in the yield by about 2 to 4% without affecting the quality of the product.

Jan 1, 1990

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By Morris Loshinsky, George Ziegler

NEW ROUTES - 63rd STREET CROSSTOWN The New Route construction along East 63rd Street in Manhattan began in 1969 with the East River tunnel connecting Manhattan and Queens. The 63rd Street Line, once in Queens, is planned to connect to another new route called the Queens By Pass or Super Express (See Exhibit 1) which would connect to the Queens Boulevard Line at Forest Hills. The purpose of the Queens By Pass was to alleviate subway congestion to and from the Borough of Queens, whose population had rapidly expanded during and after World War II. The existing Queens Boulevard subway lines (the "E" and the "F" trains) are almost filled to capacity at their terminal stations with passengers from Long Island. Passengers boarding trains enroute from the local Queens stations have difficulty boarding crowded trains, and, at times, cannot board the trains. The New Routes, thus, were to give additional train capacity into Manhattan and thereby relieve the crowded conditions along the Queens Boulevard corridor. PROFILE - METHOD OF CONSTRUCTION The portion of the New Route passing east-west under East 63rd Street on Manhattan (See Exhibit 2) had to snake beneath intersecting structures running north and south, such as the Con Rail tracks below Park Avenue and the 80 ft deep Lexington Avenue Express track structure along Lexington Avenue. Further, the Lexington Avenue Local tracks are in a separate structure which has a high profile close to the street surface. Therefore the 63rd

Jan 1, 1981

By Leonid P. Ni, Askar M. Kunayev

It is well known that processing of the high-silicon bauxites for obtaining alumina by the hydrochemical Bayer process is irrational due to the significant losses of alumina and alkali with red mud. The main source of losses of the mentioned compounds under the conditions of leaching by the Bayer process is the formation of difficultly soluble sodium alumosilicate of the composition Na20 .Al203, 2Si02 . n H20. A conventional method of an extra recovery of alumina as well as of regeneration of alkali out of red mud is the high-temperature sintering of the latter with soda and limestone with the subsequent leaching of sodium aluminate from the sinter by water or soda solution. A sequential version of the Bayer-sintering flow chart recommended for the prosessing of bauxites with an increased content of silica is based on this method. However, the sintering method is not the only alkaline method allowing to make an extra recovery of alumina likewise of alkali from red mud. Our investigations showed/I/, that the components mentioned can be recovered by a pure hydrochemical method of treating red mud with concentrated alkaline solutions, with lime (Ca0) being present, that was earlier succesfully used in the development of the hydrochemical method of processing nepheline rocks/2/. The possibility of extracting alumina and alkali from red mud is based on the reactions which can be schematically represented in the following way:

Jan 1, 1984

By L. Yan, T. Lutz, J. Noll

"Mine disasters, such as fires and explosions, can create a hazardous atmosphere due to the generation of carbon monoxide (CO). After a mine disaster, contaminated mine air can enter the refuge alternative (RA) as miners enter. Most built-in-place (BIP) RAs use an air delivery system to provide an unlimited supply of breathable air through a borehole which also serves to purge contaminants. In order to determine what levels of contaminants enter the RA, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted testing in NIOSH’s Pittsburgh Experimental Mine using groups of 5, 15, and 30 subjects entering the RA. The experiment used sulfur hexafluoride (SF6) as a tracer gas that was released into the air outside of the BIP RA to establish a uniform concentration. After the human subjects entered the BIP RA, the SF6 levels inside the RA were measured to quantify how much of the tracer gas entered the BIP RA. In tests conducted while the borehole air supply was left off as test subjects entered, interior contaminant levels were less than 3% of the exterior concentration. In tests conducted with the borehole air supply activated as test subjects entered, the interior contaminant levels were measured at less than 2% of the exterior concentration. Considering a mine disaster can result in 10,000 ppm of CO in the mine atmosphere, these percentages indicate that unhealthy CO concentrations that may lead to headaches, dizziness, and loss of judgement can occur in a BIP RA. This information will help mines make decisions concerning air locks, air delivery systems and a determination if purging mechanisms are necessary. INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and enforcement of mine safety standards (MSHA, 2006). Section 13 of the MINER Act specifically directs the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of RAs for underground coal mines. This mandate culminated in the 2009 adoption of changes to the 30 CFR mining health and safety regulations, requiring underground coal mines to provide RAs capable of maintaining a life-sustaining environment for persons trapped underground. Such RAs can be either pre-fabricated or BIP shelters. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe, breathable atmosphere within RAs."

Jan 1, 2018

By Steven J. Stokowski, Frederick M. Bodycomb

This chapter deals with the use of industrial minerals in insulating materials used to control our thermal and acoustical environment. There are numerous products on the market used for thermal and acoustical insulation; they consume substantial quantities of a variety of industrial minerals. Following is a brief review of the theory and function of insulating materials. Acoustics is the science of sound, and architectural acoustics deals with sound in buildings. If this definition is broadened to include transportation vehicles, it is this end use for which acoustical insulations are primarily manufactured. Sound is defined as the auditory sensation in the ear, or the disturbance in a medium which causes this sensation. Acoustical insulation is used to reduce or eliminate noise, defined as unwanted sound. Noise control may be accomplished by the reduction of sound radiation at the source, by utilizing sound reducing construction methods such as staggered studs, etc., to control sound transmission, or by using sound absorbing material on walls, ceilings, and floors (Rossing, 1985). Acoustical insulation functions by absorbing the energy in sound waves in a porous material. As the sound waves penetrate the pores, they are dissipated by reducing the amplitude of vibration of the air molecules by contact with the pore walls, with subsequent conversion of the sound energy to heat energy. Acoustical insulation is generally highly porous, 1.3 cm or greater in thickness, and has interconnected pores. Acoustical insulating materials include fibrous vegetable or mineral matter and cellular organic and inorganic material, such as natural or manufactured foams (Sabine and Moulder, 1979). Acoustical materials are most commonly porous boards and tiles, which are often composite materials with perforated facing. Roof insulation board and lightweight concrete can also contribute to the absorption of noise. Thermal insulation is defined as material used to control the flow of heat. It may be used for heat control from low cryogenic temperatures (below -100°C) to in excess of 2 200°C for applications such as ablative shields for spacecraft. Heat transfer occurs by conduction, convection, or radiation. Conduction is the transfer of heat without the movement of the conducting medium, as through a metal. Heat convection through a liquid or gas takes place by movement of the medium. Forced convection is the basis for heating and cooling equipment, utilizing pumps or blowers to transfer the thermally conditioned fluid. Free or natural convection occurs due to density differences in the fluid. Radiation is the transfer of energy in space (Eckert, 1985). Conduction of heat through a solid is reduced by insulating the body with foams, or fibrous or small celled granular material. Heat transfer through a gas (convection) is controlled by creating many small pores which inhibit the movement of the fluid, substituting a gas of low thermal conductivity, or evacuating the space. Heat radiation can be reduced by the use of materials that reflect or absorb the energy (Glaser, 1967). Thermal insulating materials may be vegetable or mineral fibers, organic or inorganic particles, or foams with small pores, generally used to form a low density thermal barrier. They may be blocks, poured lightweight cementitious materials, bricks, etc.

Jan 1, 1994

By Michael Michaylov

INTRODUCTUCTICN The coal seams at Bobov dol basin are highly prone to spontaneous combustion in Bulgaria. The risks of endogenous fires (SPONCOM) exist mainly in gob area. During the last 15 years three different technologies for preventing and fighting SPONCOM have been applied in underground mines of this basin: pulp from hard material and water, foam and inerting with nitrogen. On the basis of experimental application of these technologies as well as theoretical and experimental research a new technology - Foam Pulp Technology (FPT) was worked out. It is very effective in difficult to reach places in a gob. BACKGROUND AND THE NEED OF FPT Application of the three methods mentioned above showed advantages as well as some disadvantages, allowing determination of their effective application scope depending on geological and working conditions. Their advantages can be summarized as follows: - Foaming: high viscosity at low density, which allows forming a thick layer; good surfactant wetting properties; excellent effective cooling during evaporation in high temperature zones. - Pulping with mixture of solid particles (e.g., fly ash) and water from surface installation: easy to apply in a mine; low operational and energy costs due to gravity transport from the surface to the gob: good ecological results because the waste material is returned back underground. - Inerting with nitrogen: volumetric action which doesn't restrict the thickness of treated coal pile; easy to apply in a mine; controllable nitrogen delivery depending on fire hazard conditions. Main disadvantages of the same three methods are: - Foaming: rapid disintegration due to intrusion into heterogeneous and porous media and high costs due to the need of frequent large volume foam flows (short foam's life); - Pulping: inapplicable for coal piles with high thickness which is of great importance in the cases of seams with ununiform hypsometry (rapid and frequent changes in a seam configuration) and/or great volumes of coal or ore piles particularly heated to a high temperature; strong dependence on gob floor declination; water draining of the working face area which impedes the movement of supports and chain conveyor's. - Inerting: relatively high costs hardly depending on the rate of face advance (fig.1) in comparison with the other methods; it is difficult to ensure sufficient oxygen at the exit end of the face. This problem is crucial in faces with a high level of methane emissions; accelerating of the oxidation and spontaneous heating of the pile after turning off the nitrogen supply. Inerting should be applied again at higher capacity of nitrogen supply (fig.2) and what is more important, it shouldn't be

Jan 1, 1995

By K. Kavouridis

Coal is broadly recognized as sure, competitive, diversified, not vulnerable and predictable in price energy resource. In power generation coal is playing a dominant role in the EU-27 with 25% of installed capacity and almost one third of the power generation. The role played by the domestic resources and especially by coal are increasingly becoming the focus of the EU energy strategy. There is a strong pressure for the decarbonization of the energy mix. The Emission Trading system (ETs) can have an impact on the shift to lower carbon-intensity fuels. The impact of ETs on coal can be important, because it is very short sighted and only defines the period up to 2008-2012. The ETs CO2 regime must ensure that investment in coal-fired plants in the long term are supported. EU Research Institutes and Coal Industry identified an important CO2 reduction potential by improving the efficiency of the conversion of solid fuels into electricity. Highly efficient clean coal technologies can contribute to reasonable costs and challenge the issue of climate change. It must be pointed out that the EU Energy policy should now concentrate on the necessity to effectively support demonstration projects and to create the legal framework for the integrated approach of efficiency enhancement and CCS. It is not a right approach to implement CCS before the technology is demonstrated and before it is clear that it will be commercially viable.

Jan 1, 2007

By D. Altizer, E. Thompson, K. F. Unrug

Because of frequent sudden changes in the geologic composition of strata, the extrapolation of rock properties obtained from core samples to the surrounding areas can cause problems. To address this issue, a method of rapid strength testing in situ using a borehole penetrometer is being developed. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. Rock strengths are determined di¬rectly on the drill-hole wall. The latest development is a borehole penetrometer that requires only a 38.1-mm- (1.5-in.-) diam hole. The small diameter of the penetrometer body allows for the drilling of test holes with production mine equipment such as a roof bolter. The new penetrometer allows for the possibility of a broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 2002

By S. Tuylu, D. Adiguzel, A. Bascetin

"Optimization techniques are successfully used in many different fields such as engineering, physics, economy, and politics in order to enhance the performance of the systems. In concrete technology, Aggregates are prepared by mixing the water and cement in proportional quantities. In order to obtain desired quality control parameters, the determination of the ingredients ratios is one of the important problems for the optimization. Additionally, in the quarries where the aggregate quality constantly changes, blending optimization must be made to obtain a sustainable aggregate quality. This study showed that linear programming, which is easy and which includes many aggregate properties, cannot be used in terms of some aggregate properties. Therefore techniques such as nonlinear programming or genetic algorithm must be used. INTRODUCTION Concrete is a used construction material and made by mixing the aggregate, cement, and water. The concrete properties are directly related to the properties of these materials in blending. The quantity of aggregates in concrete is approximately 70 percent of the concrete’s volume. Therefore, the most important material is aggregates. The extraction of aggregate materials in quarries is more problematic because of variable bedrock properties. Therefore, the quality of the materials changes and the characteristics of the concrete are also influenced directly. In terms of sustainable use of natural resources, produced aggregate materials which have different qualities should be used optimally (Adiguzel et al., 2014). Nowadays, in the solution of the blending optimization, various optimization techniques are being used such as linear programming, nonlinear programming, and genetic algorithm. In this study, blending optimization techniques especially used for concrete aggregates blending have been summarized, and the advantages and disadvantages of these techniques have been introduced. BLENDING PROBLEMS Blending is a frequently encountered problem in process-type manufacturing such as mining, refinery, food industry, chemical industry and metal industry (Sakalli 2010). Blending is a commonly used method in lots of practical solutions (Sarker and Newton 2008). Several optimization techniques are available for blending problems (Furman and Pardalos 2009). The most important issue is to blend with minimum cost. The blending problem is a special linear model which was developed to solve this problem. In blending optimization research, linear programming is a widely used method (Adiguzel et al. 2011; Bascetin and Adiguzel 2011)."

Jan 1, 2016

By Vicki Seppala

Phelps Dodge Mining Company operates some of the world’s largest open pit mines. Safely mining in these deep pits requires the commitment to a proactive integrated slope management process. The slope management process also includes the continued look for improved slope design, construction, and maintenance of slope faces. This paper discusses integration of such technology as electronic programmable detonators, 3D imaging using ground-based LiDAR scans, and reflectorless slope monitoring systems in a slope management program.

Jan 1, 2005

By John D. Kalasky

Island Creek Coal Company has had, for many years as a primary concern, the activity of handling large quantities of methane in the ventilation of its deep mines of southwest Virginia. Since the development of the Beatrice operation in the mid 19601s, the concern has been well founded, and through the years progress has been made in this most important facet of the extraction of the coal reserves to insure the safety of the employees engaged in the mining opera- t ions.

Jan 1, 1980