Search Documents

By Alim Elibol, Rosbel Jimenez, Mustafa Can Suner, Deniz Tuncay, Zach Agioutantis

LaModel is a displacement-discontinuity variation of the boundary element method, which is utilized to analyze the displacement and stress in flat-lying, tabular orebodies. In coal mining, the accuracy and reliability of LaModel are proven with the utilization of the Mark- Bieniawski coal pillar strength and the stress gradient formula with proposed methodologies. However, the application of LaModel is limited to coal mines due to the default coal pillar strength properties. Recently, the stress gradient functions have been established and used to derive concentric rings of zones to simulate stone mine pillar yielding in LaModel. Also, to gain a robust understanding of the brittle failure mechanism and its effect on pillar strength, an S-Shaped failure envelope, where rock mass' cohesive and frictional strength components mobilize as a function of confinement (e.g., minimum principal stress), has been implemented into FLAC3D software. Therefore, by employing brittle failure criteria, the pillar strength stages at various width-to-height ratios and different pillar dimensions are estimated for four benching stages. The estimated pillar strengths and stress gradients for benching conditions are then used to calibrate LaModel in-seam material properties and compare stresses computed by LaModel and FLAC3D. Consequently, this study aims to increase the safety measures in the stone mining industry by implementing the practical use of LaModel for underground stone mines' initial development to various stages of bench mining.

Jun 25, 2024

By D. C. Hatch

At the MacIntyre Development of the Titanium Division of National Lead Company a magnetite-ilmenite ore together with gabbro-anorthosite waste is mined from an open pit by shovels and trucks. The ore from the pits is trucked to ore stockpiles for blending ahead of the crusher and to free the mine from crusher delivery schedules. The ore stockpiles are blended to yield a 16.5 to 17.0 % TiO, crusher feed. This requires mining on an assay cut-off rather than a visual grade cut-off. Highly mineralized ore runs from 20 plus % TiO2 and 30 plus % Fe to 15 % TiO2 and 40 plus % Fe as the ratio of ilmenite to magnetite changes. There are three major ore types in the present pit with magnetite ratios varying from about one to one up to three times as much magnetite as ilmenite. Ilmenite and magnetite together liberate from gangue down to about 10 mesh and this is the basis of the magnetic cobbing. Below 10 mesh the ilmenite and magnetite start to separate and ore cobbing pulleys will not hold the ilmenite.

Jan 1, 1968

By Armando Alatorre

The Republic of México is the world's largest producer of celestite/strontium carbonate and natural sodium sulfate. It is also a significant producer of flourspar, barite, graphite, sulfur, feldspar, salt and gypsum. New production may be brought on stream for borates, wollastonite, garnet, calcium carbonate and others. The country covers a geographic area of approximately 2 million square kilometers (760,000 square miles), and is divided into seven geological/geomorphological provinces. Less than 20 percent has been explored in detail for either nonmetallic or metallic minerals. This leaves large areas available for the discovery of world-class industrial mineral deposits. In addition to new deposits of those minerals currently being produced, there is exploration and development potential for borates, magnesite, rare earths, nepheline syenite, heavy mineral sands and numerous others.

Jan 1, 1995

By Anthony D. Songer, James E. Diekmann, Jarrett E. Carlson

Computer Aided Design (CAD) systems are currently recognized as a necessary tool for the management of projects. Currently, CAD is used for TBM and conveyor setups, concrete lift design and overall constructability reviews. Typically, such CAD models exist only in 2 dimensions. The advent of more powerful computers, enhanced CAD programs and after market animation packages provides tremendous potential to the Tunneling industry. In particular, effective application of these technologies enhances cost, time and quality in field operations.

Jan 1, 1997

By E. Kokinou

The main scope of the present study is to investigate the suitability and sensitivity of the magnetic susceptibility as a pollution monitoring tool in urban areas. For this purpose, a municipal park located in the centre of Chania city, which may be affected by traffic and domestic heating pollution, was selected as the study area. In the context of the present work, magnetic susceptibility measurements were conducted in two phases. Surface soil samples were collected in 2006 from the area under investigation and they were analyzed in order to estimate the spatial distribution of the magnetic susceptibility. One year later, mapping of the magnetic susceptibility has been contacted in situ using Bartington MS2D and MS2F sensors. Additionally, soil samples were collected from selected positions in order to compare the values of the magnetic susceptibility with that estimated in 2006 research. Both investigations indicate high values of the magnetic susceptibility around the park near the roads and in a small area inside the park where a café is located.

Jan 1, 2008

By A. J. Lynch, M. J. Lees

Introduction The design of wet grinding circuits may vary considerably according to the duty which is to be performed. Grinding machines which are commonly used in these circuits are rod mills, ball mills, autoge¬nous mills, and pebble mills while size separation machines commonly used are vibrating and wedge-wire screens, hydrocyclones, and rake classifiers. In some circuits, such as those producing feed to cement kilns, all the ore entering the circuit is discharged in a single product stream. In others, such as those operating on magnetite-taconite ores, the feed entering the circuit leaves in two or more streams. Grinding circuits in flotation plants normally include sections in which either the concentrate or the tailings from the primary flotation circuit is reground and these additional sections should be regarded as an inte¬gral part of the grinding circuit. A typical circuit is shown in Fig. 18. Problems in achieving maximum efficiency may occur at three stages: 1) At the design stage when the optimum size reduction flow¬sheet must be selected with respect to the types, numbers, and sizes of processing units. 2) At the operating stage when the correct selection of values must be made for those variables which may be altered while the circuit is off-line but which are constant while the circuit is on-line, for instance the vortex finder diameter of the cyclones. 3) Under conditions of continuous operation when changes in the circuit feed or in the mechanical operation of the circuit may cause undesirable changes in the circuit product. The first two prob¬lems are concerned with optimization, that is, with making the best choice from many possibilities, and the last with control. Optimization Problems. The main purpose of a wet grinding circuit is to produce particles with a sizing distribution which will ensure optimum performance of the later chemical reaction or physical concentration circuits, because it is on the efficiency of these later circuits that the economics of the total mineral treatment process depend. The size distribution of the product from a grinding circuit may be affected by many variables, some concerned with the arrange¬ment and operation of the machines and some concerned with the ore characteristics, and it is important that these should be recognized in the design and operation of the circuit. For instance, in a simple ball mill-cyclone circuit the variables which affect the product size even for constant feed characteristics are shown in Fig. 19. In addition, the rate, size, hardness, and mineralogical composition of the feed will affect the performance of the circuit and the product size. When the circuit contains more than one mill, both the number of choices available and the complexity of the problem are increased consider¬ably. Consequently, one type of problem which is to be solved if an optimum product is to be obtained from an existing grinding circuit is that of circuit design, and this includes arrangement of processing units and selection of those operating conditions which cannot be altered when the circuit is operating, such as mill speed and cyclone inlet and outlet dimensions. The other major problem in optimization is encountered at the design stage when a choice must be made about the type, number, and size of processing units. For instance, for a typical high-capacity size reduction operation, should two circuits each containing one rod mill and two ball mills or three circuits each containing one rod mill and one ball mill be used? Alternatively, should ball mills only be used and if so, how many, what size, and what arrangement?

Jan 1, 1985

By Kenneth S. Johnson

Iodine, a grayish-black nonmetallic element, with a density of 4.9 g/cm3, is a solid at ordinary temperatures. It is a member of the halogen family, along with fluorine, chlorine, bromine, and astatine. Iodine melts at 114°C. and at 184°C it is volatilized to a blue-violet gas that has an irritating odor. It does not occur as an element in nature, but occurs as iodates, iodides, or other combined forms. It is the 47th most abundant element in the earth's crust. Iodine was discovered by Bernard Courtois in 1811. He observed an unknown substance in the crude soda ash that results from the burning of seaweed. Samples of this unknown substance were identified to be a new element, and in 1813 Gay-Lussac named the substance iode, from the Greek word for violet color. The world production during 1989 and 1990 [(Table 1)] is estimated to be about 16 million kg per year (Lyday, 1991), of which about 30% is consumed in the United States. GEOLOGY AND MINERALOGY Compounds of iodine are minor constituents in seawater and brines, in certain marine organisms, and in minerals of the Chilean nitrate deposits. Seawater contains approximately 0.05 ppm iodine, and certain marine organisms, such as seaweed, sponges, fish, and some brown algae, are able to further concentrate iodine (Lyday, 1989a). Some seaweed can extract and accumulate iodine up to 0.45% of their weight, on a dry basis. The northern Chilean nitrate deposits, in the Atacama Desert, contain the following iodine minerals: lautarite, Ca(I03), (calcium iodate); dietzeite, CaJIO,), (CrO,) (calcium iodate-chromate); and bruggenite, Ca(I03), . H20 (Erickson, 1981). Various subsurface brines also contain iodine compounds. Some gas-field brines in the United States and Japan locally contain 30 to 1 300 ppm iodine. Several coals in Germany also contain iodine compounds. Iodine has been recovered from brines mainly in Japan and the United States, but also in Java, Indonesia, Italy, England, and the former USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. Seaweed was a major source of iodine for the world in the first half of this century, and it remains as a large resource. The reserves and future resources of iodine are large, even excluding the resources in seaweed and seawater, and are shown in [Table 1]. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable. PRINCIPAL PRODUCING COUNTRIES Major iodine-producing nations are Japan, Chile, the USSR, and the United States, with lesser amounts being produced in China and Indonesia ([Fig. 1; Table 1]). Annual world production in 1989 and 1990, respectively, is estimated at 15.6 and 16 million kg. In Japan and Chile, the production of iodine depends on production of other materials, such as natural gas or nitrates, respectively, whereas in US operations (in Oklahoma) iodine is the major product recovered from natural brines. Chile was for a long time the principal world producer of iodine from its nitrate-fertilizer operations, but in recent years Japan has become the world leader with increased production of natural gas and associated iodine-rich brines.

Jan 1, 1994

By Patrick McElhinney, Jacob Carr, Bruce Whisner, Cory DeGennaro, Jingcheng Li

Since 2016, electromagnetic interference (EMI) of personal dust monitors (PDMs) with magnetic proximity detection systems (PDSs) has been observed in underground coal mines. The EMI causes the magnetic field measurements of a PDS to change, which, in turn, alters the calculated location of the miner relative to the machine. Any altered location calculation can potentially cause the PDS to fail to warn a worker who is at an unsafe distance from the machine, arousing a serious concern on safety hazard caused by EMI in underground mines. The search for EMI mitigation strategies led to the development and use of large shielding pouches and boxes to hold the entire PDM to reduce its magnetic emission. Research on these pouches and boxes found that although they were able to reduce the emitted radiation from the PDM, they also disturbed the magnetic field of the PDS, affecting its performance. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have focused on shielding internal PDM components rather than shielding the entire PDM. The PDM air pump motor is one of the PDM components that has been identified as a major source of electromagnetic radiation and has been selected for further study and tests. The measurements show that a small copper or aluminum foil enclosure can effectively reduce the magnetic emission of the motor by between 50 and 85% at 73 kHz. This study compares the test results of the air pump motor with various cost-effective shielding materials. The data provided in this paper can serve as a reference for shielding enclosure design of the PDM air pump motor to reduce its electromagnetic emission as one form of EMI mitigation strategy.

By G. Van Weert, J. F. Breedveld

Both regular and Silver Impregnated Activated Carbon (SIAC) were studied for their effectiveness in removing WAD (Weak Acid Dissociated) cyanides from solutions at pH = 10. SIAC has already been shown to be effective in the removal of free cyanide down to 30 ppb or less. The present work deals with complexed cyanides. Zinc cyanide was used to represent the WAD component. At pH=10, in either batch or column tests it was not possible to lower the total cyanide in solution from either 30 or 8 ppm to less than 1 ppm, using SIAC, regular activated carbon as received, or after grinding. Silver (metal) impregnation of the carbon was not beneficial in the removal of WAD cyanide. However, when silver is added as silver ions (nitrate), the cyanide is adsorbed as silver cyanide in preference to zinc cyanide. The latter compound converts to zinc (hydr) oxide. This way, the cyanide concentration in solution can be lowered below 1 ppm, even when zinc cyanide is already adsorbed on the carbon used. A single exploratory test with added copper ions indicated a similar effect for that system.

Jan 1, 2004

By Paul D. Chamberlin

In the author's selenium report of 1994 (1), the literature was culled for selenium removal technologies that had a chance of producing effluents with <10 ppb of total selenium. Very few processes could achieve such low concentrations. The EPA dictates such low concentrations. Discharges to fishery waters must be <5 ppb total selenium. The federal max­imum contaminant level ( MCL) for drinking water is 50 ppb. The EPA regulations are for total selenium, not for the species, perhaps because an approved EPA assay method is atomic absorption and it cannot distinguish between species.

Jan 1, 1996

By Cloyd D. McDowell

The Federal coal Mine Health and Safety Act of 1969 has been criticized by those who say it goes too far in controlling the activity of private enterprise and by those who say it does not go far enough in eliminating fatalities and accidents in an accident prone industry. Possibly a better evaluation of this legislation lies somewhere in between. From the viewpoint of the coal industry it can be said that through the efforts of those engaged in mining, both the operator and the miner, the year 1969 marked a record year in mine safety with only 190 fatalities and a frequency of 0.84 per million man hours exposure. This outstanding achievement compared to any previous was the result of a determined effort on the part of a concerned industry to improve its reputation as being the most hazardous industry in the nation. After the effective date of the Act, March 31, 1970, the Bureau of Mines assumed complete control of all safety and health activities of the mining industry. Unfortunately, there was no improvement in the safety record of underground mines in 1970 with the total of 255 fatal injuries and a frequency of 1.04 for the year. The number of fatalities declined to 177 in 1971 but the number of underground coal mines had declined from 5,955 to 2,268 during the two year period. Meanwhile, surface mined coal increased from about 38% of total production in 1969 to over 50% in 1971, keeping the annual production of coal at a normal level but involving fewer men.

Jan 1, 1973

By K. T. Dreher, J. A. Brierley, C. L. Brierley

Water from underground uranium mines located in the Ambrosia Lake district near Grants, New Mexico, U.S.A., is treated to reduce levels of uranium, selenium, radium and molybdenum. The treatment system consists of a series of ponds and an ion exchange plant. Bacterial and algal populations present in the pond system are considered agents which actively assist in removal of the pollutants present in the water. Pondbottom sediments maintain a reducing zone and a large population of sulfate-reducing bacteria of the genera [Desulfovibrio] and [Desulfotomaculum]. Uranium, molybdenum, and selenium accumulate in the pond sediment. Stimulation of the microbial sulfate-reducing activity resulted in a decrease of soluble concentrations of these elements in laboratory systems. Predominant components of the treatment ponds’ algal flora are the filamentous [Spirogyra] and benthic [Chara]. Laboratory study indicates that [Spirogyra] is more active than [Chara] in removal of uranium and molybdenum from solution. However field-collected algal samples of both of the genera contain uranium and molybdenum. Laboratory studies indicate that death and decay of the algae in association with pond sediment does not result in return of cellbound uranium and molybdenum to the water. The algae appear to act as bio-filters for accumulation of particulate pollutants and agents for adsorption and/or absorption of soluble pollutants.

Jan 1, 1980

By Gregory A. Vaka

Robins Engineers & Constructors, Inc. as the exclusive U.S. licensee introduced the PIPE CONVEYOR to the North American marketplace early in 1984. The sale of the first PIPE CONVEYOR in 1985 was a difficult task since the conventional troughed belt conveyor was the accepted and the most widely used means of continuous transportation of bulk materials handling in the world. Initially our clients viewed the PIPE CONVEYOR as a departure from the normal and accepted form of material handling. Since then, the parent company of Robins Engineers merged with Krupp of Germany to form KRUPP ROBINS, INC. in the United States. To date there are over 462 PIPE CONVEYORS operating worldwide with the majority of the long overland systems designed and installed by Krupp Robins, Inc. The PIPE CONVEYOR is now becoming the norm, viewed by those who are familiar with its capabilities as the preferred method of transportation for all bulk solids.

Jan 1, 1997

By G. G. O. O. Uwadiale, M. A. U. Nwoke

The recovery of iron from low-grade (31.6% Fe) Muro iron ore was investigated using reverse anionic flotation of quartz. Tests were performed to investigate the effect of pH, the effects of using distilled vs. tap water as the flotation medium and the effects of using cassava starch vs. dextrin for the depression of iron minerals. The optimum results were obtained around pH 10 and 11, and cassava starch was superior to dextrin in depressing iron oxides. Investigations at pH 11 using cassava starch and distilled water resulted in a concentrate grade of 69.4% Fe with a recovery of 84.4% Fe. Under the same conditions, the use o f dextrin produced a concentrate grade q f 65.9% Fe with a recovery of 78.6% Fe. Investigations at pH 10 using cassava starch and distilled water resulted in a concentrate grade of 60.2% Fe with a recovery of 83.9% Fe, and under these conditions the use of dextrin produced a concentrate grade of 56.1 % Fe with a recovery of 81.5% Fe. Flotation studies conducted at pH 11 using tap water and cassava starch resulted in a concentrate grade of 70.4% Fe with a recovery of 92.7% Fe. This demonstrated the superiority of tap water over distilled water in the reverse anionic flotation process. Investigating the effect of calcium ions on the activation and flotation of quartz with oleic acid revealed that a calcium ion concentration of 50 to 100 ppm was optimum.

Jan 1, 1996

By Ronald L. Haxby

This report presents a refractive seismic technique for evaluating the strength of rock within an open pit bench. A concept of correlating rock strength and seismic velocity is discussed and a method of predicting the degree of fragmentation of a pit bench is introduced, Figure 1 shows the area of interests [ ] Most of the work was performed while completing graduate studies at the University of Arizona.

Jan 1, 1967

By Richard E. McGee

The paper presents a description of the procedures that were used to generate a ventilation criterion based on measurements of ambient mine air exhaust pollutant gases and ventilation airflow quantities. Today&apos;s economics dictate that a ventilation requirement be based on actual operating conditions. This will assure optimum economics and a safe working environment at the same time. The paper presents a methodology by which a ventilation requirement is based on the average maximum expected concentrations of nitric oxide (NO), nitrogen dioxide (NO2), carbon monoxide (CO), and carbon dioxide (CO2) that equipment operators in one of our Southeast Missouri mines will be subjected to. A graph has been generated whereby the expected maximum levels of NO, NO2, CO and CO2 are plotted against the ventilation quantity of a mine stope.

Jan 1, 1982

By G. Buchan

This paper discusses the design of long panels for longwall mining at Twentymile Coal Company (TCC) from conception to implementation. The case study of the long panels at Twentymile includes extensive mine plan reengineering in the early 1990&apos;s to world record production months in 1996 and 1997. The obstacles of subsidence engineering, environmental regulations, conveyance, ventilation, equipment design, and continuous miner (CM) development timing had to be overcome to successfully begin longwall production within a 4 year time frame. The background and some detail for each of these areas listed will be discussed to show how the coordination of many facets must be pulled together to implement a successful long panel mine plan.

Jan 1, 1998

By Richard R. Klimpel

The first part of this two-part article summarizes the result of a 10-year, multimillion dollar research and plant testing program involving operating mining companies throughout the world. The program was aimed at developing a better understanding of the influence of slurry rheology on the performance of mineral/coal grinding circuits. Part 1 presents the basic concepts identified, including typical laboratory results showing the influence on grinding behavior of controlled changes in percent solids, particle size, slurry temperature, and viscosity control chemicals. Part 2, in January, will illustrate typical industrial scale test results on both open and closed circuits using the concepts presented in Part 1. Special emphasis will be placed on identifying some industrial operating implications of controlling rheology by different methods. Introduction The industrial-scale practice of wet grinding minerals and coals in tumbling media mills (ball, rod, and pebble) is well-known to operating mineral processing engineers and plant design personnel. Over the last century, considerable experience and data has been collected, correlated, and put into rules or guidelines for successful circuit design and operation. Typical factors influencing circuit throughput that have been analyzed in some depth are mill diameter and length, grinding media size and loading, feed and product particle size, mill power use, and the interaction of classifier type and efficiency with the grinding device. Until recently, knowledge of slurry rheology influence on large scale grinding circuit performance has been limited. Even today slurry rheology effects are essentially ignored in plant design. Indeed, in most plant operations only qualitative guidelines are followed. For example, too thick a slurry causes throughput losses and too thin a slurry uses excessive water or causes water handling problems such as pumping limitations. A search of published literature and numerous discussions with experienced plant operating personnel has shown an awareness that changing the percent of solids in the mill influences grinding or the response of grinding involving fine feeds versus coarse feeds. However, most the work identified relative to rheology effects in mineral/coal grinding was qualitative. Even in the few studies that were more quantitative, the scope of the work was usually too narrow to draw general conclusions. Also, the detailed rheological characterization tied to observed breakage and the combination of laboratory to industrial-scale testing that is required to develop a broad understanding of any factor influencing grinding had not been done. In this environment, this detailed program began in 1967. It had three distinct goals: • To develop a basic understanding of slurry rheology influence on breakage characteristics in the laboratory. • To test general rheology concepts developed in the lab on the industrial scale. • To develop a commercially viable chemical approach to controlling slurry rheology that would lead to the use of chemical grinding additives or grinding aids. The goals have been met, at least in part, this year. A small fraction of the extensive laboratory and plant results have been made available in published literature. Much of the research program dealt with identifying and developing chemical grinding aids, but a lot of useful and practical information on percent solids, particle size, and slurry temperature influence on grinding circuit performance also was collected. The purpose of this article is to present a clear and concise sum¬mary of the results of the entire program. The importance of rhe¬ology control in grinding circuit behavior will be demonstrated using a series of carefully per¬formed industrial scale experi¬ments (both open and closed cir¬cuits) that have not yet been reported in general literature. Mining companies participating in the test program on a proprie¬tary basis have found the informa¬tion in this article to be useful in better understanding and improv¬ing circuit performance. Viscosity Effects in Grinding Studies In this program&apos;s previous labo¬ratory studies, it was shown that there is a consistent pattern of change in specific rates of break¬age of both mineral and coal slur¬ries as slurry fluidity changes. Using the net production rate of material smaller than some spec¬ified size-for example, kg/hr of <75 µm (200 mesh)-as an index of mill production in a standard batch mill test (with a given feed material, feed size, mill, and mill conditions such as constant time of grind), the following facts were established (see Fig. 1): • The normal range of low den¬sity, low viscosity slurry (region A) gave no variation in mill produc¬tion. The measured rates of break¬age exhibited normal first order grinding. • Grinding of a somewhat higher viscosity slurry (region B) could give increased production. The higher viscosity was obtained

Oct 12, 1982

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry, and seal manufacturers recently conducted a series of full-scale experiments within the underground experimental mine at PRL’s Lake Lynn Laboratory. The purpose of the experiments was to evaluate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in 6 to 10 hr and are capable of withstanding explosion overpressures in excess of 140 kPa (20 psi). These novel seal designs use available mine materials, do not require conventional rib hitching, and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

Jan 1, 2003

By Hasan Kolayli

Zeolites are common secondary components of a variety of igneous rocks. However it is extremely rare to reach such abundances to form a rock. An unusual rock composed almost entirely of natrolite, a zeolite mineral, has been discovered ; in a mountainous terrain called the Kop mountain range in the eastern Turkey. In the region, country rocks are essentially metamorphic rocks. These unique rocks are resulted through metasomatic changes acted on microdioritic and andesitic parent rocks occurring generally as dikes and stocks in the country rocks consisting chiefly of serpentinized harzburgites. These metasomatic rocks are investigated with respect to their mineralogical, petrographical, and geochemical characteristics. These products consisting dominantly of natrolite are termed "natrolitite" and those containing additional pargasite, an amphibol mineral, are termed "pargasite-bearing natrolitite or pargasitic natrolitite ". The dikes and stocks show concentric zoning, each of which has distinct chemical and mineralogical compositions: Na2O and H2O contents show enrichment outward from the core to chill zones whereas, SiO2 and CaO show depletion. Mineralogically, plagioclase variety, abundance and chemistry change outwards from the center due to partial to complete replacement of natrolite: anorthite contents of plagioclases decrease outward, which is indicated by A1203 and CaO decrease and SiO2 and Na2O increase, showing inverse relationship with increasing natrolite content.

Jan 1, 2005