Search Documents

By R. P. Gardner

Results of work on the development of a phenomenological model for the continuous flotation process using short-lived radioactive tracer techniques for the determination of model parameters is reported. A model that incorporates a flotation first-order rate constant and a residence time distribution based on the cross flow finite state (CFFS) model has been derived and investigated. The short-lived radioactive tracer techniques necessary to extract the model parameters have been developed as have the necessary nonlinear search methods. The conditions under which all the model parameters can be extracted from a single radiotracer experiment are detailed and illustrated. A microcomputer-based unique data logging system has been designed, assembled, and implemented for collecting the necessary transient radiotracer data. Results are reported for a continuous laboratory flotation system for the two systems mica ore and coal.

Jan 1, 1985

By Robert Labbe

The final tunnel lining for this project involved pumping vast quantities of concrete over large distances under the extremely busy streets of lower Manhattan. Approximately 68,000 cubic meters (89,000 cubic yards) were pumped from various locations over 152 meters (500 feet) below ground (Figure 1) to create nearly 14.5 kilometers (9 miles) of 3.05 meter (10 foot) diameter tunnel. Total distances pumped exceeded 1,645 meters (5,400 feet) horizontally after a vertical difference of over 152 meters (500 feet). The urban setting of the operation, coupled with the long distances over which concrete was pumped, created many problems which had to be dealt with along the way. A three-shift labor operation was implemented to allow sequential pouring of tunnel sections nearly every day. The fine tuning of the mix design was critical to make this operation successful.

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008

By John Zeni

In Australia during the 1990s, Zeni Drilling took on several demanding shaft boring contracts. This paper describes the safety, operational, technical and environmental advantages derived through the implementation of mechanized boring methods for two of these projects. The paper first describes a 3-meter (10 ft) diameter access shaft blind bored from an underground location to 440 meters (1,444 ft) deep for a gold mine in Tasmania. The construction of a 5.8-meter (19 ft) diameter, 515-meter (1,690 ft)deep ventilation shaft for a longwall coal mine in New South Wales is also described.

Jan 1, 2001

By D. E. Poole

Injury Prevention: Dependent, Independent and Interdependent In recent years, management-directed (dependent)safety programs have lost ground to the more successful self-directed (independent) programs, where employees take responsibility for their own safety. Today, with the growth of the team concept in industry, a mutual-caring (interdependent) approach to workplace safety is gaining wide acceptance. This presentation compares characteristics and results of the three progressive levels of safety responsibility and explains how to develop a successful interdependent program. The presentation will also detail the common principals that are necessary for safety excellence under any of the management styles.

Jan 1, 2000

PolyMet Mining is developing the NorthMet property near Duluth, MN. Laboratory investigations have led to the development of the Platsol process to dissolve in one step the base metals (copper and nickel) as well as the gold and platinum group metals (PGM). To complete the prefeasibility study, a fully integrated, 10-day pilot plant trial was undertaken. The trial consisted of high-temperature (>220ºC or >428ºF) pressure oxidation in the presence of 5 to 10 g/L chloride (the Platsol process). This was followed by solid/liquid separation, gold plus PGM recovery from solution, conventional copper solvent extractions/electrowinning (SX/EW) and recycling of the copper raffinate to the autoclave. The concentrate tested during the trial period was a NorthMet bulk flotation concentrate. It assayed 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t (0.041 oz/st) Au, 2.2 g/t (0.064 oz/st) Pt and 9.9 g/t (0.289 oz/st) Pd Laboratory results were confirmed and, with minor adjustments of the laboratory Platsol conditions, the following leach extractions were obtained during the pilot plant trial: 99.6% Cu, 98.9% Ni, 96% Co, 94.6% Pd, 96 % Pt and 89.4 % Au.

Jan 1, 2003

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24% of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50% of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include • extraction of thick seam in ascending order with stowing ; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving ; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof, four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 3, 1987

By John E. Tilton

Real copper prices during the past several decades display two striking characteristics. First, they are highly volatile. Within a year or two, copper prices can rise or fall by 30% or more. Second, over the longer term, they are falling. Indeed, since 1970, the secular trend price for copper is down by more than 50%. Figure 1 highlights both of these characteristics. It shows the average annual US producer price for copper since 1970 measured in constant 2001 US dollars. While the London Metal Exchange (LME) copper price is not shown, it and the US producer price have for some time moved more or less together. So pronounced short-run fluctuations around a significant long-run decline describe copper prices, not only in the United States, but around the world.

Jan 1, 2002

By Michael Stanwood

Project feasibility no longer involves just technical and economic viability-today's feasibility study must include environmental, regulatory, and political considerations as well. While the US now appears at least somewhat committed to developing synthetic fuels, including oil shale, it is the environmental issues, rules, regulations, and guidelines that will play the major role in determining the timing, magnitude, and overall scope of synfuel development in the coming years. The key environmental obstacle affecting oil shale development is uncertainty. Although oil shale may be the most environmentally studied "new" technology in the world, little is known with much degree of certainty about potential environmental consequences of one full-scale commercial facility, or the effects of a massive development effort in a relatively pristine and sparsely populated area. Other primary environmental uncertainties include: • Environmental compliance costs and their effects on investment decisions; • The reliability and acceptability of anticipated pollution control technologies; and • The confusing, time-consuming environmental regulatory framework, which requires more than 100 permits, clearances, and reviews before development occurs. This discussion will focus on the latter uncertainty, and will describe he current status of potential constraints to oil shale industry development in five areas: water availability; water quality degradation; air quality degradation; reclamation and spent shale disposal; and community impacts.

Jan 1, 1981

By Clair Murdock, David Heath

The 1,280 MW Sir Adam Beck II Hydroelectric Project was constructed in the1950s, at Niagara Falls, Ontario, Canada. The twin intake tunnels total over 17 kilometers in length and pass deep below the City of Niagara Falls. The tunnels were excavated using drill and blast methods, with a top heading and bench approach. The shot rock was loaded with electric shovels and transported to the five shafts with off-highway trucks. The tunnel muck was hoisted to the surface by skip and transported by truck to disposal areas. The volume of underground excavation for the 15.55 meter diameter tunnels and the shafts exceeds 3,500,000 cubic meters, then and now the largest underground civil works excavation by drill and blast in the Western Hemisphere. The lining required over 900,000 cubic meters of concrete. All of this work was completed in three years, remarkable progress, considering the technology of the day, comparing very well with the rapid excavation and tunneling methods of the twenty-first century. Big, fast, and deadly—at least 20 lives were lost in construction accidents.

Jan 1, 2007

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues which may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Mining Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has now been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff co-operation across the country. MEA has also now commenced some international teaching initiatives which are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual university programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 1, 2009

By K. Zeidler, T. Schwind

The Fort Canning Tunnel, Singapore, is an approximately 50 feet (15m) wide vehicular tunnel under shallow ground cover that has been constructed according to the principles of the NATM. Its shallow location in soft ground combined with a high groundwater elevation in close vicinity of historically important features called for special design considerations combined with a rigorous monitoring scheme. Surface, sub-surface and in-tunnel instrumentation was installed to monitor the performance of the ground and tunnel support during construction. Comparison of actual reading data with the results from the computer modeling carried out during the design phase is provided in this paper.

Jan 1, 2007

By Steve Kral

For a state whose roots are in mining, most Colorado residents probably do not realize that the industry still contributes heavily to the state’s economy. In 2005, the industry contributed, directly and indirectly, about $8 billion to the state’s economy, according to the Colorado Mining Association (CMA). It employed nearly 10,000 people at mines and support businesses. And the mining industry in Colorado is one of the highest paying occupations in the state, averaging about $80,000 a year in wages and benefits. The state’s coal mining industry produced nearly 36 Mt (40 million st) of coal in 2005, valued at $800 million, the CMA said. That was seventh in the nation. And Colorado’s only major gold mine produced 10.2 t (329,000 oz) last year, valued at $124 million. That was third in the nation. And Phelps Dodge’s Henderson Mine produced about 12.7 kt (28 million lbs) of molybdenum, valued at $350 million. Colorado is the largest molybdenum producing state in the nation.

Jan 1, 2006

By Bruce Richardson

A contractor-manufactured 4.75m (15'-7") diameter EPB shield excavated a 115m (375 ft) long tunnel under the San Antonio River as part of the Salado Creek to Dos Rios Pipeline Interconnect Project in San Antonio, Texas. Lignite, limestone concretions, and sandstone in the face of the tunnel required the use of disc cutters. Less than 7.6m (25 ft) of sand and gravel hydraulically connected the top of the tunnel to the channel of the river. Fully lagged steel ribs with filter fabric were used for initial ground support and water control. This and other contractor manufactured TBMs in the 1.2 to 4.75m (4 to 16 ft) range are presented with descriptions of the jobsites, equipment, performances, and problems.

Jan 1, 2008

By Janine Acasi, Robert D. Rogers, Jonathan K. Trautman, Richard C. Cronn, James H. Wolfram

The demand for phosphate will continue into the future, because phosphate is currently irreplaceable as a plant nutrient and in many chemical applications. Phosphate is not recycled, so the supply must be replenished through a process of mining and purification. The most energy intensive part of the process, separation of phosphate from the ore, requires 54 to 78% (depending on the method used) of the estimated 0.5 quads of energy consumed by the U.S. phosphate industry. This paper provides data from a project designed to determine if a biotechnology can be developed to separate phosphate from its ore. Several hundred microorganisms (both bacteria and fungi) capable of solubilization of phosphate ore have been isolated from the environment. Work is ongoing to determine the mechanism for solubilization. In addition, how these organisms could be used in a bioprocess is being investigated.

Jan 1, 1989

When the 2008 Olympic Games begin in Beijing, China is September it will not only mark the end of the journey for the Olympic torch and the thou-sands of participating athletes, but the games will also mark the culmination of a massive amount of construction in the city. On display for the world to see will be 31 new and refurbished venues including the 91,000-seat National Stadium called the ?Bird?s Nest? and the aquatics center, called the Water Cube. What will not be featured as prominently on the television cameras broadcasting the games around the world will be the network of tunnels built beneath the city. But that infrastructure of rail lines will be of critical importance to the games. While preparing to host the world, China added a subway tunnel that will include four stops in the Olympic Park. The 4.4-km (2.7-mile) subway line that runs through the complex of stadiums, gymnasiums and parks began trial operations in June. Prior to the opening of that line, Beijing's No. 5 subway line, which runs through the heart of the city from north to south, opened in October. That 27.6-km (17-mile) line took nearly five years to build and includes 23

Jan 1, 2008

By K. Hanumantha Rao, A. Nayak, K. S. Narasimhan, S. N. Mahapatra

B.A. Hancock It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rupture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding-classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective flocculation separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 9, 1986

By Colin Lawrence, Michael S. Schultz

Due to the planned deepening of the NY Harbor, NYCEDC/NYCDEP is planning to replace two existing water lines between Brooklyn and Staten Island with one deeper water pipe. The crossing, just north of the Verrazanno Bridge is 1.75 miles long. The new pipeline will be tunneled using gasketed concreted segmented liners. Apressurized face machine will be used through the soft ground. This will be the first subaqueous application using this technology in New York City. This paper discusses the planning, design and risk issues associated with the crossing and the challenging soil conditions that resulted in the decision to use a pressurized face machine.

Jan 1, 2007

By H. K. Lin, J. L. Oleson

The purpose of this study is to develop a mathematical model to describe the oxidation of cyanide with SO2as proposed in the Inco process. This research employed a direct method for measuring the change in cyanide concentration with respect to time as effected by varying concentrations of SO2, copper and pH. Developing this model may be applicable in determining optimum conditions in a process well known and used in the mining industry. It was determined that the reaction is first-order with respect to cyanide, SO2and [Cu+2].The reaction order is 0.15, or zeroth order with respect to [H+] at pH range from 8.0 to 9.5.The activation energy, Ea, is 21.6 kJ/mol. The overall rate equation, as determined through this study is: [ ]

Jan 1, 2004

By S. S. Hsieh

Bench-scale beneficiation studies were made on Idaho dolomitic phosphate rock using the TVA carbonate flotation process. The process employed diphosphonic acid as a phosphate mineral depressant and fatty acid as a carbonate mineral collector. Silica was subsequently rejected as float using an amine collector, with phosphate product recovered as the sink fraction. Two samples of prepared flotation feed from commercial operation were used; one contained 21% P205 and 3.2% MgO, and the other contained 26% P205 and 1.8% MgO. The results indicate that concentrates containing 31-33% P205 and 1% or less MgO can be obtained, with P205 recovery of about 80%.

Jan 1, 1984