Search Documents

By J. N. Adamson

The Alcan Smelter project at Lynemouth on the Northumbrian coast draws cooling water for the power station through shafts and tunnels from the North Sea. The sea at this part of the coast is frequently very rough and even in calm weather the coastal currents are strong. The adjacent coal mine makes use of these currents to disperse colliery waste and discharges into the sea some thirty thousand tons each week. In consequence the sea bed is continuously shifting and the sea is black and turbid. Construction of sea shafts under these conditions presents difficulties as drilling from a floating vessel is hazardous and sea bed activity of divers is greatly hindered by the entire absence of visibility. After considering several alternatives a method of construction was agreed with the Consultants in which the drilling and also the lining of the shaft would be completed in sequence from an eight legged work barge (GEM 126). Each shaft would be drilled to full depth and a steel cylinder, with its ends closed temporarily, would be lowered into the hole and grouted into the formation to form a full-length permanent lining. The bell mouth for each shaft would be constructed in advance to form part of the cylindrical casing. On interception of the shaft by its appropriate tunnel the lower end of the cylindrical casing would be cut away and the internal walling of the shaft installed from below. After completion of construction the shafts and tunnels would be flooded and the bell mouth sealing covers removed by divers.

Jan 1, 1997

By G. L. Finfinger, F. E. McCall, A. A. Campoli, M. D. Zuber

Injecting pressurized water into a coalbed prior to mining reduces mining-generated respirable dust. Because of economic and geological barriers, water infusion for longwall dust control in the United States is now limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes that are drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob-gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob-gas boreholes. Computer coalbed-reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water-infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1997

By M. J. Garcia, Howard Hallman, G. M. T. Marshall, Ken Higby, Louis Cope, Robert S. Hess, John Peters, A. G. Law, William C. Larson

After a good year in 1979-strong mineral demand, adequate prices for most metals, minimal labor problems-1980 was not so good. The US produced $24.8 billion worth of nonfuel minerals last year, up 3.5% from 1979, according to preliminary US Bureau of Mines figures. But the $800 million increase was the smallest annual gain since 1977 and reflected reduced auto and construction industry demand, strikes, and energy shortages. Preliminary figures for 68 minerals show that production of 42 decreased, 25 increased, and one was unchanged. Production of 11 of 21 US-produced minerals was up. Noteworthy mineral events in 1980 included a copper industry strike, increased gold and silver prices, troubles in the iron ore and uranium industries, discussion about a US nonfuels mineral policy, and corporate interest in mining companies as merger targets. Recessionary conditions experienced by the Western world in 1980 resulted in a slowdown in new mine development, evident in the relative scarcity of major new base metal projects. This could lead to short term supply/demand anomalies within the next few years which, in turn, could have a significant effect on metal prices, according to Mining Magazine (Jan. 1981). World Mining (Sept. 1980) noted that US mining strength is in open pit operations. A much lower tonnage is mined underground and is centralized in trona, uranium, lead, zinc, molybdenum, potash and, to a lesser extent, copper. The most notable increase in new underground mines has been in Wyoming's trona district where new mines are being developed and production will increase, the magazine said.

Jan 5, 1981

Compared to alternative ways of dealing with coal fines, oil agglomeration has always been a commercial bridesmaid and never yet a bride. Yet interest is high in the process, as shown by a number of pilot plants in operation that are funded by industry as well as government. In the past in the US, alternative ways to handle coal finer than 100 to 200 mesh included flotation, or no treatment except dewatering, or discarding the fines as waste. There are now a number of factors that tilt the economics more toward fine coal recovery. Today, the cost of mining a ton of underground coal runs from $22-30, and discarding even 10% as unrecovered fine coal is a real economic loss. A number of attempts (notably by EPRI) have been made to quantify the effect of coal cleaning on utility boiler operations. Transportation and ash handling costs, frequency of unscheduled outages, fouling and slagging problems, and boiler tube erosion are all lowered by cleaning coal. The advantage of coal cleaning on these parameters has been shown, but the dollar amount varies with many assumptions and is difficult to pin down. The message to a utility, however, has not been lost and the trend toward cleaner steam coal is accelerating. This may lead to fewer installations that only wash the coarse coal, and add back the unwashed fine coal until a maximum contractual ash limit is reached. And, as the proportion of coal fines continues to increase by continuous and longwall mining, it may become impossible to clean the coal sufficiently without cleaning the fines. Flotation and oil agglomeration are the only processes that presently deal directly with cleaning the very finest coal fractions. Flotation has proven its effectiveness in cleaning blackwater and in separating fine coal from mineral matter. It has the achievable potential for far greater pyrite rejection than is now obtained in commercial preparation plants. While flotation will continue to be the predominant method for fine coal cleaning, there are conditions and opportunities where oil agglomeration can be a

Jan 8, 1980

There are several simulators available and are being used for analysis, improvement and optimal control of the grinding process. However, these tend to be developed on informal software engineering methodologies. The informal approach is not suitable for long term development and a formal design methodology is necessary to develop efficient, error-free, and easy-to-use and to maintain software. In meeting this goal, basic concepts of a software model for describing the mineral process objects has been proposed. The software model forms the basis for software design and efficient implementation of the simulation. This paper describes the development of software models for grinding circuits. The work constitutes the theoretical foundation for the development of an advanced simulator for comminution.

Jan 1, 1995

By Brij M. Moudgil

Lack of understanding the major process parameters and inadequate scale-up factors have led to the belief that fundamental knowledge is not important for successful flotation plant operations. Flotation of simple and easy to process ores may not require a strong fundamental knowledge base for day to day operations. However, as low grade complex ores are mined and process control is integrated into flotation schemes, it is imperative for a plant operator to acquire a strong background in the basics of the flotation process at hand and/or have access to such a knowledge base at short notice. In order to meet the challenges of unexpected changes in the feed, reagent quality, water chemistry, physical, mechanical and hydrodynamic conditions, the flotation plant superintendent/chief metallurgist must have a strong background in the flotation fundamentals.

Jan 1, 1993

By Juan L. Yarmuch, Gonzalo Sepulveda

Medium- and short-term mine planning holds immense significance in optimizing production and resource utilization. It serves as a vital link between the long-term strategic plans and the day-to-day operational activities of a mine. In this context, a mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the net present value (NPV) of the schedule while ensuring enough room for the operation of mining equipment.

Jul 1, 2024

By P. Somasundaran, D. R. Nagaraj, Jing Wang

Polysaccharides have been widely used as depressants in mineral processing for decades. They constituent one of the most abundant family of biopolymers. However, only a small number of them have been used by industry so far because of a general lack of understanding of interactions between these polymers and minerals. In this work, adsorption tests, electrophoretic mobility measurements, microflotation and fluorescence spectroscopic tests were performed along with computer simulation to explore the mechanistic aspects of guar gum adsorption and conformation on talc as a function of relevant variables such as ionic strength, pH, solvent composition and polymer molecular weight. From microflotation tests, it was found that talc hydrophobicity decreased markedly due to the adsorption of guar gum even at very low concentrations and reached a plateau below moximum adsorption. Guar gum adsorption on talc was found to be not affected significantly by changes in solution conditions such as pH and ionic strength, ruling out electrostatic force as controlling factor for adsorption. Fluorescence spectroscopic studies showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Also urea, a hydrogen bond breaker, reduced the adsorption of guar on talc. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding in preference to electrostatic or hydrophobic force. This information should help toward designing reagents of optimum molecular architecture for efficient depression, dispersion or other such surface modification of particles.

Jan 1, 2005

By Keivan PakIman, Maziar Pasdarpour

Transportation tunnels are highly sensitive to ground movements and are required to be stable and secure for safe operation. In urban areas, the interaction between tunnels and adjacent piles, which are widely used to support buildings and other structures, requires careful consideration. The seismic response of tunnels may vary depending on the lateral stiffness and strength of the tunnel walls, while the axial loading and seismic impact of adjacent piles may cause soil displacement and stress changes that can damage the tunnel lining. As a result, tunnel owners often impose strict limits on the design of new piles lying close to existing tunnels including maximum allowable tunnel deformation, stress change limits, and minimum tunnel to pile separation distances. This paper describes a numerical analysis of the inuence of the axial loading and seismic impact of bored pile foundations on subway tunnels, undertaen using the nite element software laxis D. ased on the results of the numerical analysis, the paper suggests a more realistic and less conservative approach for designing piles in close proximity to transportation tunnels. INTRODUCTION The interaction between tunnels and adjacent piles can cause stress changes and displacements in the soil and structures which may adversely impact structural performance and tunnel safety. It is therefore important to take account of relative load transfer and piling conguration when designing new piles in

Jun 23, 2024

By Thomas J. Feeley

The US Department of Energy (DOE) is supporting the engineering development of three advanced physical coal cleaning technologies: selective agglomeration, advanced flotation and advanced cycloning. Each is capable of significantly reducing the pyritic-sulfur content of US coals. The objective is to provide the coal and electric-utility industries with a cost-effective option for addressing the SO, emission reductions required by the 1990 Clean Air Act Amendments (CAA). A secondary objective is to evaluate the potential of advanced coal cleaning for removing trace elements that are precursors to the formation of hazardous air pollutants (HAS). The proposed National Energy Strategy (NEE) and the 1990 CAA lay a foundation for a more efficient and environmentally sustainable energy future (1991). The need to use energy resources in an environmentally sound manner presents critical challenges and opportunities for coal preparation during the next decade, particularly regarding the control of SOS and HAY emissions. The principal challenge is the development of cost-effective coal preparation approaches for sulfur and HAY precursor removal.

Jan 1, 1993

By K. S. E. Forssberg, S. Subramanian, Hanumantha K. Rao

The dispersion characteristics of apatite and magnetite minerals have been assessed based on zeta-potential measurements, using various inorganic and organic reagents, namely sodium silicate, sodium tripolyphosphate, sodium hexametaphosphate and lignin sulphonate. These results highlight that apatite is dispersed to a greater extent vis-à-vis magnetite. Further, the dispersion efficiency of the phosphate reagents is better than that of sodium silicate or lignin sulphonate, for both apatite and magnetite. Batch flotation tests on a high phosphate magnetite ore from Kiruna indicate that higher apatite recovery with minimum phosphorous loss to the magnetite fraction can be achieved using sodium silicate as a dispersant. Although comparable dephosphorization can be attained with lignin sulphonate dispersant, the recovery of magnetite in the non-float fraction is lower, possibly due to the adverse synergistic effect of this organic reagent with the Atrac collector, resulting in the flotation of magnetite. The high intensity conditioning of pulp for up to 30 min resulted in better apatite flotation with <0.015% phosphorous in the magnetite product.

Jan 1, 2002

By Yutaka Mochida

OUTLINE Beginning in 1946, a careful geological survey was made of the Tsugaru Straits. In 1964, excavation of the exploratory tunnels were started to observe the characteristics of faults and rock formation directly, and to study construction methods of excavation and sealing water inflow. In March 1971, the investigation stages were over, and in April 1971, the construction project was authorized from the government. The geological features in the straits may be divided into three broad classes. One third consists of andesite on Honshu side. The other two thirds consists of tuff. The middle of the straits consists of tuff, so-called Kuromatsunai-layers. On Hokkaido side, it consists of tuff, called as Kunnui-layers. There are nine noteworthy faults on the route. Prior to the excavation of the main tunnel, the horizontal pilot tunnels and service tunnels are made. Exploratory borings are taken to confirm the geological conditions and the presence of gushing water. Groutings for sealing water inflow are carried out when necessary. In geologically bad conditioned sections such as disintegrated or fractured zones, special methods are applied. In geologically good zones, the tunnels are bored through using the same methods as for a mountain tunnel driving. The pilot tunnel being constructed at the sea bottom is under direct control of the Japan Railway Construction Public Corporation. The service tunnel and the main tunnel are being excavated by contractors.

Jan 1, 1981

By M. J. McPherson, P. Mousset-Jones, G. Danko

Ventilation and refrigeration fortune climate modification contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can he used to minimize the impact of these costs. There are several computer codes available to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely, what accuracy is required of the basic input parameters, in order for a certain precision to he obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel&apos;s superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed, to the changes of the rock thernrophysical properties, the heat transfer coefficient, and the wetness factor.

Jan 1, 1987

By Allan E. Hall, Stephen G. Hardcastle, Lucien D. Nel, Jean-Paul Saindon

A description is given of the investigation conducted at Sherritt Gordon&apos;s Ruttan Operation in Manitoba during 1986. Gas and dust concentrations were measured in the exhaust air of the major working sections to assess the potential for recirculating exhaust air into the intake air in winter to reduce heating costs. The results indicate that there is excellent potential to significantly reduce winter heating costs by controlled recirculation of exhaust air. Gas and dust concentrations vary significantly during the working shifts but have consistent trends from shift to shift and day to day. The variations in gas concentrations have similar trends but no single gas could be reliably used to predict the variation of the other gas or the dust concentrations. Dilution and the other effects which reduce pollutant levels as the exhaust air returns to surface indicate that recirculation should take place as close to surface as possible, subject to the economic constraints of the airway construction required and the extra fan energy required for the longer recirculation path. Recommendations are made for the choice and positioning of air and dust monitoring sensors and the logic of a control system. Economic analysis of the results indicates that controlled recirculation is viable at an existing mine with a pay back period of approximately two years. Incorporation of a system into a new mine at the planning stage would significantly shorten the pay back period.

Jan 1, 1987

By T. Ertekin, R. V. Ramani, W. Sung

The emission of methane in the coal mine working faces has two immediate impacts with regard to coal mine planning. Firstly, at the planning stage, the coal mine ventilation system must be designed such that airflows in the faces keep the concentrations of the gas in faces areas to below one percent. If the concentrations were greater than one percent, the production machine has to be shut down resulting in a loss of productive time. In an extreme case, concentration can reach explosibility limits which may lead to ignitions and explosions. Secondly, in excessively gassy coal seams, several alternatives can be applied to the mine layout configuration, and the mining method to be predicted for the extraction of coal, so as to insure a productive and safe operation. In this study a two-phase, two-dimensional finite-difference model was used to predict the methane emission rates into active mine working area under several methane drainage schemes. The numerical model utilizes a recently developed multi-mechanistic flow theory which describes the flow of methane in an heterogeneous and anisotropic coal seam. Transport of methane in the micropore structure of the coal is described by the Fick&apos;s law of dif- fusion under the influence of existing concentration gradient, while flow in the more permeable butt and face cleats (macropore spaces) is formulated by Dar- cy&apos;s law under the influence of existing pressure gradient. The desorption of the methane is accounted with the aid of a quasi-steady kinetic sorption model. A series of simulation studies were conducted in a systematic manner by sifting through the parameters associated with the coal seam characteristics and the degasification strategies in order to understand those which most significantly affect the methane emission rates in the face areas during mining. Along these lines, the effects of coal seam properties such as thickness, porosity, permeability, sorption characteristics and scheduling of drainage process against the mining operation have been isolated to understand the role of each individual parameter on the methane emission rates.

Jan 1, 1987

By Robert N. Evans, Delon Hampton

During construction of the Washington Metropolitan Area Transit System, the hand-mining of a mixed-face condition was anticipated on a portion of tunnel located in the downtown area of Washington, D.C. The Section, consisting of two circular tubes, extends from Station 12+80, heading in a westerly direction, traverses along a curve under Lafayette Square, and ends in a northwesterly direction at Station 37+62 (see Fig. 1a). It was near the northernmost portion of the section that the mixed-face condition was encountered. Decomposed rock was first encountered in the invert at Station 31+00. From this point the rock gradually increased in height until it intersected the springline at Station 37+62, the project limit. Summarized within this paper are measurements of the soil load on a horseshoe-shaped portion of tunnel located in the mixed face condition. These measured loads are compared to the soil load on tunnels as determined by current design methods. The paper also discusses rib and surface movements associated with the post loading process. Comments will be made on how the presence of a mixed face condition might help or hender the tunnel design and construction procedures.

Jan 1, 1974

By C. I. Everson

The Elkhorn mining district is located 35 kilometers southeast of Helena, Montana, on the southeast edge of the Boulder Batholith. Geologically the district consists of a folded sequence of Paleozoic limestones and shales which have been thermally metamorphosed and altered by monzonite to diorite intrusives related to the Cretaceous Boulder Batholith. For the most part, the skarns are associated with metasomatic: replacement of calc-silicate hornfels, diorite and marble by iron rich, dark green pyroxene, garnet, sulfides, the district contains excess of 30,000 Kg.

Jan 1, 1992

By Reinhard Gnilsen

Ground pillar control in soil and weak rock often represents a critical and sometimes a determining factor for mined underground civil structures. A concept is desirable that minimizes the restrictions possibly imposed by pillar control requirements on geometrical tunnel characteristics and on the mining operation itself. Conventional concepts are discussed and an alternative concept is introduced. This concept reduces pillar control requirements to ground control measures required with "regular" tunnels. The conventional model of pillar mechanics with potential yielding of a ground body in more than one direction, is then avoided. Due to the complexity of pillar mechanics, the level of engineered design furnished to the contractor is crucial to optimizing ground pillar control. Conventional versus alternative contractual arrangements for pillar control are described and their important role is illustrated. The concept introduced relates to principles inherent to the New Austrian Tunneling Method (NATM). However, tunnel projects using other mining concepts can employ alternative ground pillar control principles as well, if certain criteria are observed. Case histories in the United States and abroad are presented and the impacts from different concepts of ground pillar control are illustrated. The paper concludes by analyzing concept characteristics that can infer monetary impacts on both the owner and the contractor.

Jan 1, 1987

By B. K. Parekh, R. H. Mehta

Handling of fine coal is an importance issue for coal as well as the utility industry. Reconstitution in form of pellet or briquet would be desirable if it could be done economically. This paper evaluates the effectiveness of three binders e.g., asphalt- emulsion, corn starch and Brewex, in forming pellets of ultra-fine clean coal. It was found that asphalt emulsion and corn starch were not effective binders for ultra-fine clean coal, however, Brewex provided excellent quality of pellets, which exceeded all the minimum quasi requirements of coal pellets. INTRODUCTION Advanced coal preparation techniques (physical or chemical) are designed to process ultra-fine (minus 200 mesh or 74 pm) coal. The average particle size of the clean coal product is about 25 pm. Currently available dewatering techniques are effective in providing a 25 to 30 percent moisture product of this size coal slurry (Parekh et al. 1989). Handling and utilization of this dewatered ultra-fine size coal is difficult. Reconstitution, which includes pelletization, briquetting, extrusion, etc., of the dewatered coal product provides an ideal answer to handling and transportation problems. However, reconstitution of fines in the coal industry has not been successful due to various reasons. The most important criterion for its unsuccessful application in the coal industry is the cost of the binder (Capes et al. 1965). Various methods of reconstitution, such as briquetting, disk pelletization, extrusion pelletization and roller and die-pelletization, have been tested for fine coal agglomeration (Conkle et al., 1991) (Richards, 1990). Conkle et al., (1992) have provided a detail analysis of each technique in terms of moisture and operating cost requirements. According to Conkle, briquetting requires a product containing very low moisture, whereas pelletization can be done with coal containing up to 30 percent moisture. Currently available dewatering technique provides about 25 percent moisture product, thus, pelletization appears to be an ideal route for reconstitution. In this paper, results are presented on the comparison of three different binders i.e., asphalt-emulsion, corn starch and Brewers condensed solids (BCS or Brewex), for fine coal pelletization.

Jan 1, 1995

By Malcolm J. McPherson

This paper describes the algorithm used in a BASIC program for an IBMXT microcomputer, to simulate the underground mine climate. The program called CLIMSIM has been developed and refined over several years as a result of considerable use at operating mines. The program has been designed to be easy to use and be understood by the practicing mine ventilation engineer. It provides predictions of the work place climate, so that the optimum ventilation/cooling system can be designed to obtain a certain air cooling power or effective temperature at the work place. An example is given of the application of the program to a mechanized cut and fill stope at the Homestake gold mine in South Dakota.

Jan 1, 1986