Search Documents

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

The term unsaturated flow refers to the conditions in which soil pores are filled partially with water and partially with air. This situation constitutes a porous material filled with immiscible fluids. Immiscible fluids by definition exhibit a distinct interface when in contact with each other resulting in a pressure discontinuity across the interface due to surface tension. The fluid that tends to wet the solid particles is called the wetting fluid and the other is the nonwetting fluid. In the air-water sys- tem, air is the nonwetting fluid and water is the wetting fluid. A somewhat analogous fluid system is that in a petroleum reservoir in which there may be up to three immiscible fluids-oil, salt water, and natural gas. The degree of wettability of the fluids is salt water + oil + gas. That is, salt water is the wetting fluid at any interface and oil is the wetting fluid at an oil-gas interface but is the nonwetting fluid at a water-oil interface. Since the oil-water and air- water systems are similar, much of the theory and methods of analyses for the air-water system or unsaturated flow have evolved through the petroleum literature. In the two-fluid system the pressure difference across an interface depends on the size of the pore space in which the interface occurs. The equation commonly used to represent this dependence is

Jan 1, 1986

By L. G. Austin

The general manner in which the liberation function must change during size reduction is described. Data from float-sink (washability) analysis of a coal is used as an illustration, and a Locking Index is defined and calculated. Ash is not distributed equally with respect to sieve size but is concentrated more in the finest sizes. On the other hand, the ash is less locked with coal in the finer sizes than in the larger sizes. Further crushing showed decreased locking in intermediate sizes, but the material in the fine sizes (produced from breakage of highly locked larger sizes) was more locked than material of the same size in the feed. Future work is also discussed.

Jan 1, 1995

By E. De Souza, H. Heidrich

In underground operations the evaluation of blasting fume dilution times and the application of recirculation techniques require accurate determination of the concentration of toxic fumes produced by the explosive used. This paper describes a methodology for obtaining concentrations of detonation products from commercial explosives tested under typical rock confinement and looks into the development of techniques for reducing toxic gases produced by explosives. This paper also analyses the application of techniques for the removal of toxic gas which would enable reduced re-entry times, a reduction in the quantity of fresh air and the use of air recirculation techniques, thereby providing substantial economic benefits to the industry. INTRODUCTION Toxic fumes from blasting operations are among the most common and serious hazards encountered underground. The implication of high concentrations of toxic gases emitted from blasting on the mine ventilation system are very significant and, in many cases, catastrophic results have occurred. Because blasting is a routine practice underground, the mining engineer is always confronted with the problem of controlling the fumes within acceptable levels. Typical control procedures employed underground include preventing or reducing the amount of fumes liberated from blasting through the proper selection of explosives and proper blasting techniques; removing the fumes through local exhaust systems or auxiliary ventilation (dilution ventilation); blasting off-shift, or at restricted times; localizing or isolating the effects of blasting where workings are isolated or sectionalized in the ventilation system; and absorbing some of the components of the fumes using air-water sprays. Dilution is one of the most effective control measures against blasting fumes and is universally applied. However, for precise determination of the dilution times for the fumes to reach safe concentrations, accurate determination of the concentration of toxic fumes produced by the explosives used is required. Research work has been carried out in determining the types and volumes of gases produced from blasting. In the case of ideal detonations, the nature and quantity of the fumes produced can be predicted by thermo-hydrodynamic calculations. However, commercial explosives exhibit non-ideal behaviour which is enhanced by the relatively small diameters of application in underground mines. The confinement offered by the surrounding rock further complicates the situation. It is well recognized that confinement affects performance and consequently fume generation. A detailed data base of fumes generated by commercial explosives at various conditions is introduced and the effect of blasting parameters such as, confinement, shock desensitization and incomplete detonations on toxic fume production is described for a variety of commercial explosives in use today. Thermodynamic predictions on fume production by the explosive compositions tested are also presented and compared with experimental results and their significance in assessing the quantity of fumes produced is discussed. A mathematical model capable of determining dilution ventilation requirements and dilution times to reduce the fume concentrations in the blasting zone to acceptable levels has been developed and it is being incorporated into a network system so that the effects of blasting can be simulated in typical mine ventilation systems. Solutions to the problem of controlling blast fumes within acceptable levels are described. These solutions include the use of control procedures which prevent and reduce the amount of fumes liberated from blasting. The use of low fume explosives, proper blasting techniques, dilution ventilation and filtration can be combined to effectively control fume production and save on costs. The application of these techniques to enable recirculation of underground air with reduced quantities of fresh air requirements is evaluated in a case study.

Jan 1, 1993

By J. W. T. Ropkins, D. Allenby

The paper describes a technique by which large concrete boxes are unobtrusively inserted beneath existing highway and railway infrastructure to form new subways, culverts and under-bridges, thus avoiding the inconvenience and costs of disruption to traffic associated with traditional cut and cover techniques. A series of project examples, undertaken in the United Kingdom and United States, are used to illustrate the design and construction of the box structures, together with the technology required to control ground disturbance in the tunnel face and around the box, and the jacking systems necessary for box installation.

Jan 1, 2003

By W. D. Monaghan, G. L. Mowrey, C. W. Ganoe

In addition to developing various types of coal-interface detection systems, the US Bureau of Mines is actively involved in developing a coal rib-thickness monitoring system for high wall mining applications. One particular system that shows promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1996

By D. L. Madge

The text of this chapter was not received in time for printing.

Jan 1, 1979

By Robert Snow, Francisco Sotillo

Six types of amines were evaluated in the cleaning step of the rougher concentrate for the Crago “Double Float” process in terms of relative selectivity. Selectivity of these amines was ranked based on both batch and locked cycle flotation tests. Two parameters were used for selectivity ranking, the Selectivity Index, SI, and the ratio of insol rejection to the tailings weight percentage, R*. The comparison of the flotation results of the batch tests of the cleaning step of the Crago process for an unsized amine feed generated the following ranking from the most selective to the least selective mine: Quaternary > Primary [ ]Tertiary [ ] Condensate > Ether > Secondary(?).

Jan 1, 2002

By R. S. Shepard

A quick glance at a-portion of the title of this discussion -'Rolling With The Punch" may immediately lead you to assume that I am about to expound on the so-called manly art of self-defense. So that you will not have been misled entirely we will devote our considerations to a far more important art and if I may, I should like to begin by quoting Vincent Van Gogh. According to a literal translation the artist in describing one of his famous paintings said "these peasants are eating their potatoes with those very hands that dug them from the earth' and put them in the dish". Vincent Van Gogh may not have realized at that time, that he could likewise have been describing what is probably one of the oldest of all arts - the art of Material Handling - an art that man with the aid of science has tried to improve since the beginning of time.

Jan 1, 1963

By J. N. Albright

Both microgravimetry and crosshole seismic tomography are means by which subsurface collapse and rock failure may be observed. We show results of calculations that predict changes in gravity and gravity gradient that result from void migration, bulking, and hydrology disruption due to room and pillar mining. Crosshole seismic tomography also holds promise for detecting and mapping changes in structure during subsidence. Commercially avail- able logging tools, advances in theory, and recent field results strongly suggest tomographic surveys are now possible. Subsidence phenomena which may be located are faulting, joint separation, bed parting, water table changes, and formation outgassing.

Jan 1, 1982

Crushing and grinding activity in 1989 followed the rapid pace of the mineral industry. Use of existing installations, demand for expanded capacity, and implementation of entirely new operations contributed to a high level of activity. At the 1989 SME-AIME Annual Meeting in Las Vegas, NV, the crushing and grinding session focused on wear materials in crushers and mills. Another session joined the process control group in its simulation-modeling and control of crushing and grinding circuits. Both sessions addressed the optimization in operating effectiveness. Specific subjects covered grinding media wear of forged and cast grinding balls and rubber lined mill liner wear. Also, the Semi Autogenous Grinding (SAG) Mill Conference in Vancouver in September 1989 provided a valuable update on the progress of SAG operations in recent years. Operationally, gold grinding and roasting circuits were implemented in 1989. Freeport McMoRan Gold started up two operations in Nevada. Two other circuits, both using SAG mills, are scheduled to start in 1990. These will be in Nevada and British Columbia. Elsewhere in gold, additional capacity continues to be brought onstream, both domestically and worldwide. In copper, expansions continue to call on additional crushing and grinding units. The unrest at Bougainville in Papua New Guinea has fueled a continued, strong demand for comminution in the copper sector. Specific equipment installed or started in 1989 included the ac variable frequency drive SAG mills in Australia, Alaska, and Papua New Guinea. Also, the gearless drive SAG mill in Chile provides tremendous flexibility in terms of mill speed. The trend toward moveable in-pit crushers continues -even at established operations.

Jan 1, 1990

By J. B. Stockton, D. J. Robbins, E. T. Woodburn

Batch flotation data in an equilibrium cell show that beneficiation improves with froth drainage. The limiting lamella thickness in a well- drained 3-phase coal froth appears to be determined for ultra-fine particles (-45µm) by the d90 particle size. The froth stability is considered to depend on the existence of a very thin liquid film between the outer surfaces of the d90 particles and the bounding bubble interfaces of the lamella in which the particle is held. The dependence of the coalescence rate of bubbles in these froths on the residual surfactant concentration in the lamella liquid is then consistent with stability analyses for two-phase foams.

Jan 1, 1988

By Yanchuan Li, Haifei Yao, Haiyan Wang

"Dust pollution is very serious in coal mining process, which is a great threat to the underground staff health and equipment and facilities safety. Coal seam water injection in mining process is an effective way to reduce coal mine dust concentration at the source. However, the effectiveness of water injection is limited in high-pressure and low-porosity coal seam. To improve the moisture content of coal seam, expand the wetting range and enhance the effect of dust reduction by water injection, the injectability and influencing factors of coal water injection are analyzed by numerical simulation method, and the sealing technology under high-pressure condition is studied. Then, according to the practical conditions of Tangkou coal mine, the parameters and process system of process system are designed, the effect of high-pressure water injection in coal seam was determined by testing water injection quantity, water increment and dust concentration. It is showed that the dust-removal rate of the high dust concentration operation such as falling coal and moving frame is 63.49% and 59.72%, the maximum dust-removal rate of multi-processes is 53%, which achieve a high level of application. The research results in this paper is of important theoretical and practical value to improve the water injection effect of high-pressure and low-porosity coal seam and improve the efficiency of dust removal in coal mining process.Introduction With the increasing of the depth and mechanization of coal mining, coal dust, the impact of ground pressure, ground temperature and other natural disasters continue to upgrade the harm degree (Wang 2011, Wu et al 2012), disaster incidents occur frequently, which seriouslythreaten the safe and efficient mining and the physical and mental health of underground staff. Coal seam water injection can effectively reduce the coal dust when coal crushing, prevent the impact of mine pressure, coal and gas outburst disasters, by increasing the thermal conductivity of coal, reduce coal temperature, and prevent spontaneous combustion of coal. In addition, coal seam water can soften the hard coal, so that speed up the recovery rate, improve coal production and efficiency (Wu et al 2008, Nie et al 2007). However, the coal seam in many mining area is with high-pressure and low-porosity feature, Coal joint cracks are not developed and relatively hard, water injection is difficult in these coal seams, then the desired disaster prevention effect cannot be achieved (Jin et al 2001, Zhao et al 2000). In this paper, the numerical simulation and field test methods are used to design the high-pressure and low-porosity coal seam water injection technology, so as to solve the difficult problem of coal dust control in high-pressure and low-porosity in deep well mining process."

Jan 1, 2017

By E. A. Rychkun

With the aid of modern computer automation, certain mathematical techniques are easily adapted to geophysical, geochemical and geological data analysis. First and second derivative filtering (or transformation) of raw data, in many cases, gives a better indication of anomalous conditions than conventional methods of analysis. The calculations involved, which are tedious manually, are simple, accurate and fast with the assistance of Fourier analysis and modern computers.

Jan 1, 1968

By R. Torbin

The degree to Which automation/remote control/robotics has been utilized in the mining industry is far less compared to general industry because of several factors. These factors include the adverse working environment, the difficult work operations, and the generally lower incentive for capital investments in new mining equipment. Foster-Killer has been actively involved in the development of advanced mining and underground construction equipment. This equipment is designed to be remotely operated to improve both productivity and worker safety. Many of these machines employ advanced electronics and robotic features. Other types of Foster-Miller developed robots will also be described Which could be applied to special mining problems. The types of machines that will be discussed include the following: remote shaft lining/placement. remote excavation/mining operations, automated conveyor system, and robotic surveillance.

Jan 1, 1989

The Colorado Joint Review Process (JRP), a bold step to expedite energy and mineral projects, is off and running. Blazing the trail is Amax Inc., which serve as guinea pig in JRP's development and is now test-flying the process at its Mt. Emmons molybdenum property in Gunnison County, CO. Although JRP is still in its infancy, the new permitting review process has drawn enthusiastic applause from across the resource spectrum: William K. Reilly, president of the Conservation Foundation, said JRP is "one of the most interesting projects I've seen" and called on environmentalists to monitor its progress "because it appears worthwhile." Stan Dempsey, vice president of Amax Inc., noted that of all the locales in which Amax operates, Colorado is "the only place where the complicated mine permitting scheme appears to work"-an achievement he attributes to JRP. Lynda Lee Brothers, the federal Energy Department's assistant deputy secretary of environment, reported that an extensive DOE search has not turned up "another single mechanism in all of government and private industry as good as JRP as a model for the proposed federal Energy Mobilization Board."

Jan 7, 1980

By Peter K. Achireko, Samuel Frimpong

Design and optimization of open pit limits are of paramount importance because they provide information for evaluating the economic potential of a mineral deposit and for developing short and long range mine plans. Many algorithms and their modifications have been used to design and optimize open pit limits. These algorithms have provided mine planning engineers with pertinent information in designing, optimizing and extracting ore reserves by open pit technology. However, they do not address the random field properties associated with the ore grades and reserves and commodity prices, and thus, fail to yield the truly optimized pit limits in any time horizon. In this paper, a new algorithm, MCSIMFNN, which overcomes these limitations is proposed and used to optimize open pit limits. The random field properties of the ore grade and reserves have been modelled using the modified conditional simulation based on the best linear unbiased estimation and local average subdivision techniques. Artificial neural networks are used to classify the blocks into classes based on their conditioned values. The error back propagation algorithm, in the neural networks, is used to optimize the pit limits by minimizing the desired and actual outputs error in a multi- layer perceptron under the pit wall slope constraints. The optimized pit value obtained by this algorithm has been compared to that from the Lerchs-Grossman's algorithm in a case study. The results are the same, but in random multivariable states, the MCSI MFNN algorithm is the most suitable for pit optimization. The method is also fast since it mimics the operation of the brain in the solution of the pit optimization problem.

Jan 1, 1996

By Geoffrey Purcell

The flotation response to amine collector of quartz and the feldspars microcline and albite, of the pyroxenes augite and spodumene, and of olivine can be, explained by a physical adsorption model. Flotation decreases in the order given above, and the different behavior of the three groups is attributed to structural variations of the silicates, With sulfonate collector both chemical action and physical adsorption play their part in producing hydrophobic surfaces, and flotation increases in the order given.

Jan 1, 1966

By M. J. Meulendyke

Within the mineral processing Industry. a range of grinding conditions exists which include semi-autogenous grinding (SAG), rod milling. and conventional ball milling. Each of these mill environments presents a unique environment for grinding media, requiring the application of specific physical and chemical properties for optimum grinding media performance. The environments are characterized by varying degrees and combinations of abrasive, corrosive, and impact wear. An extensive test program has been conducted to determine the extent wear rates vary between these different applications. Test results are related to production results, ball size, and mill operating conditions.

Jan 1, 1989

By R. Gong, R. Bhaskar

The development of a three-dimensional mathematical model for evaluating airflow fields at a continuous miner face is described. The model utilizes three-dimensional incompressible flow, mass continuity, and momentum (Navier-Stokes) equations to predict the airflow velocity at the face. Obstacles and equipment in the face area are modeled using appropriate boundary conditions. Parameters such as flow velocity and face dimensions can be modified and evaluated for various schemes, such as exhausting and blowing ventilation, using either brattice or tubing. A model such as the one described, with additions for local effects, can be used to evaluate novel face ventilation ideas before initiating expensive full-scale tests or field studies. The model described is a step in the direction of advanced predictor models.

Jan 1, 1993

By G. H. Jardine

Mine planning and production scheduling in surface mines are basically iterative processes which are ideally suited to the use of computer-based techniques. Both processes are truly three-dimensional and lend themselves to the application of 3-D interactive graphics. Until recently, this has applied the need for the costly, dedicated graphics screens and mid range minicomputers. However, ongoing advances in processor chip design led to the emergence of inexpensive and powerful 5 to 10 Mips desktop work- stations. These workstations have the processing power to support rapid, high resolution, 3-dimensional graphics. By combining these workstations with powerful 3-D CAD software and, with a suite of comprehensive mine planning and scheduling applications, Mincom has developed a most cost effective solution to modern mine planning challenges.

Jan 1, 1989