Search Documents

By V. P. Keran, K. Leung

Two 32 foot x 14% foot, 6.4 MW autogenous mills have been installed in the Mount Isa Mines Copper Concentrator to replace the fine crushing plant, fine ore bin, rod mills and primary ball mills. This paper describes the reasons for the change, the rationale for the new circuit design and configuration, the design and scale-up processes used to size the mills, considerations for the installation of large mills inside an operating concentrator and some early operating data.

Jan 1, 1992

By James L. Parks

This paper describes improvements in SAG and AG mill liner designs and their cumulative effect on wear life and mill availability. Routine procedures used by many SAG and AG mill operators to improve liner life are reviewed. Guidelines are provided for estimating the time required to replace worn liners along with practical methods to reduce downtime for liner replacement. Finally, the effects of mill operating conditions on liner wear life and breakage are considered.

Jan 1, 1998

By S. K. Kawatra, K. J. Shoop

An analysis of an iron-ore processing plant showed that its performance was affected by seasonal temperature variations, resulting in reduced grinding efficiency during the winter months. Laboratory and pilot plant studies were conducted to determine the cause of the observed loss of efficiency at lower temperatures. Two types of experiments were performed: drop tests and wet grinding tests. Drop testing was performed to determine the effect of brittleness and frozen pore water on the breakage characteristics of the ore. The wet grinding tests were divided into laboratory tumble tests and pilot-plant tests. The combined results of drop testing and wet grinding were used to make predictions on the performance of plant-scale autogenous grinding. From the drop tests, it was determined that dry iron ore, basalt and sandstone did not change in brittleness over the temperature range studied (-25º to 25ºC). However, when the rocks were water-saturated, the highly porous sandstone became considerably more fracture-resistant upon freezing, due to "grouting" of the pores and preexisting cracks by ice. This effect was not seen for either the iron ore or the basalt, because they were considerably less porous than the sandstone. Tumble tests on both laboratory and pilot scales showed that both the addition of fines to the test charge and a reduction in temperature caused a decrease in the amount of new fines produced. This reduced fines production was the result of increased slurry viscosity when either the fines content increased or the temperature decreased.

Jan 1, 1998

By William J. Francart, Gary J. Wirth

Fire detection capability in conveyor belt entries of coal mines has advanced considerably since the passage of the Federal Coal Mine Health and Safety Act. The advances in instrument technology and computer based monitoring have provided better fire detection than ever introduced in the industry. This paper discusses recent belt conveyor fires and detections in mines utilizing CO Monitoring Systems. Data from investigative reports is presented on belt entry fires from 1991 to the present.

Jan 1, 1993

By Graeme Lyall, Oy Leuangthong, Clayton V. Deutsch

There are many variables to consider in the evaluation of nickel laterite deposits including the concentrations of nickel, iron, silica, and magnesia. These variables show complex relationships with each other such as mineralogical constraints, non-linear correlation, and heteroscedasticity. The complex multivariate relationship between the variables cannot be reproduced by conventional Gaussian or indicator geostatistical techniques. We introduce the stepwise conditional transformation method as a pre- and post-processing multivariate transform for the stochastic simulation of a nickel laterite deposit. Transformed data are multiGaussian and independent at h = 0; thus, cosimulation can be avoided after verification that variables are independent at all lag distances. Back transformation restores the features of the input multivariate distribution to the simulated realizations. The complex multivariate correlations are reproduced and sensitivity issues are addressed.

Jan 1, 2002

The authors give a corrected form of the Korobov algorithm of optimal open pit determination and describe a method of optimising the mining sequence within a preliminary pit design. A method of automatically including roadways is also given.

Jan 1, 1992

By Jay Jones, William D. Rech

The Henderson Mine developed a water treatment system in 1985 to meet the NPDES requirements for its mine water discharge. Unacceptable levels of Zinc and Manganese formed the basis for the design and operation of the treatment system. Since initial start up, this system has reliably removed metals from the mine water and facilitated low cost compliance with water standards. The potential addition of a bio- monitoring requirement to the NPDES Permit in 1990 has added a second dimension to the metals removal process. This paper will review the history of Henderson's success at developing a low capital treatment system for metals removal and the anticipated effects of bio-monitoring upon this system based upon preliminary bio-monitoring screening.

Jan 1, 1991

By A. J. Sinclair

Los métodos de desmuestre para estudios de viabilidad dependen de las características geológicas del yacimiento que ha de ser evaluado. Se requiere un estudio geoestadístico preliminar, teniendo en cuenta los aspectos de autocorrelación de las variables sometidas a estudio, con objeto de que el plan de diseño de muestras pueda ser optimizado para producir las estimaciones de ley y tonelaje dentro de los límites de errores establecidos. En general, debe de tenderse a una distribución regular de muestras para ello, y longitudes regulares de las mis¬mas (a partir de los testigos o cortes, por ejemplo) son preferidas con objeto de facilitar los análisis estadísticos. Los planes de desmuestre son modificados y mejorados (bien técnica o económicamente) a medida que avanza el programa y es obtenida información adicional. Las muestras a granel para pruebas metalúrgicas pueden ser evaluadas en término de va¬riaciones señaladas por todas estas muestras en un depósito y la variabilidad de la ley dentro de las mismas. Una atención adecuada sobre estas fuentes de variabilidad asegurará una evaluación adecuada de los resultados de las pruebas piloto de las muestras a granel. Por otro la¬do, un estudio mineralógico general del yacimiento es un requerimiento importante, a veces ignorado, en una evaluación más general pero semicuantitativa de la representatividad de una muestra a granel; y, además, proporciona una información muy útil para optimizar el diseño de la planta.

Jan 1, 1982

By E. R. Reeves

The mining industry has recognized the importance of engineering controls as a primary means of preventing hearing loss. The noise control treatments most commonly observed on drills and bolters during this study were windshields, sound absorbing material, and hydraulic motor covers. These controls were evaluated on machines at underground metal mines to determine the amount of noise reduction achieved by each control. The results indicate that absorbing material has very little effect on the noise level. The noise reduction attributable to the motor covers was dependent on the material used to create the cover. Properly installed windshields were the most consistent control.

Jan 1, 2004

By B. E. Zeigler

This bi-product from a nickel smelter has been manufactured over the last 30 years for the abrasive and roofing industries. This paper discusses a new development for this material a foundry aggregate used for molding sand in both ferrous and non ferrous casting industries. Test data, marketing strategies, manufacturing, and case studies will be presented from the first concept, to current production, marketing and the end use of this product.

Jan 1, 1999

By G. A. Hope, K. Watling, R. Woods, I. Chandra, I. M. Ritchie

This paper presents two aspects of gold leaching research and development. The first section of the paper covers the development of innovative gold leaching processes. The research in this area has concentrated on the development of new thiosulfate leaching systems which use Fe(III) stabilized by ligands as the oxidant in place of copper(II)+ammonia. The second section will cover the development of innovative techniques such as surface enhanced Raman scattering (SERS) to study the leaching of gold in cyanide solutions. It will be shown that the use of in-situ SERS yields information which cannot be obtained using other methodologies.

Jan 1, 2005

By Daniel McConvey

Who is the Investor? -Mainly institutional, including resource funds, other mutual funds and pension funds. -Some hedge funds. -Retail investors. -How important is the reserve disclosure to these investors? -Do these investors know the difference between a reserve and a resource?

Jan 1, 2003

By C. Bazin, D. Hodouin

Dynamic experiments were performed in a continuous open-circuit 40x40-cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transferfunction and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model, a minimum variance controller with constrained input is designed and its performances are compared, by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By T. X. Ren, J. S. Edwards

Although much work has been carried out in order to understand the mechanism of spontaneous combustion and hence minimise its potential risk, the spontaneous combustion of coal continues to be a problem in coal mining. The Department of Mineral Resources Engineering of Nottingham University has been active in conducting fundamental research into the problem of spontaneous combustion of coal. For years standardised adiabatic oxidation tests have been used to identify coals and other carbonaceous materials liable to spontaneous combustion. Recently the apparatus has been computerised and coupled with an expert system known as ESSH to evaluate the potential of self-heating of coal on the basis of intrinsic coal properties, geological settings and mining techniques. A numerical model has been developed to study the aerodynamics of airflow in the wastes of longwall coal faces. The Computational Fluid Dynamics approach is being explored to simulate airflow behaviour and nitrogen inertisation processes within the goaf. Such a model would be used in locating the areas most liable to spontaneous combustion and improving the utilisation of nitrogen. It would also be possible to determine the most likely path ways of combustion/heating products so as to provide an indication of the most appropriate locations for fire detectors.

Jan 1, 1997

By S. K. Kawatra, T. C. Eisele

The separating efficiency of a flotation column is largely limited by the degree of back mixing of tailings into the froth zone, and the recovery is limited by the degree of short-circuiting of feed to the tailings. Current columns are typically constructed very tall (30 to 40 ft) to limit the effects of back mixing and short-circuiting. These effects can also be reduced in a much shorter column, provided that the flow in the column approaches plug flow. In this work, horizontal baffles were shown to improve the performance of a 6 -ft laboratory-scale flotation column treating a poorly floatable coal. Tests with variations in the baffle positions showed that baffles are needed both above and below the feed inlet to achieve the greatest benefit. Tracer tests with a fluorescent dye in water showed that baffles reduce the amount of feed water entrained in the froth at any given coal recovery.

Jan 1, 1996

By K. N. Han, Y. Guan

[The dissolution behavior of copper and gold from their pure state and from Au-Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the alloy composition, stirring speed of the disc. [lixiviant] concentration, solution pH and temperature on the overall dissolution kinetics has been studied. An-Cu alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and25, respectively. The dissolution behavior of these three alloys was compared, under the same chemical conditions, with that of pure gold and pure copper. In general, the dissolution of copper and old from alloys is controlled partially by surface chemical reaction and largely mass transfer.]

Jan 1, 1994

By Eugene F. Casey

As indicated on the official conference program, this presentation in not a formal one, but a synopsis of the activities of a newly created Sub-committee of the Research Council on Underground Construction, which involves itself with small diameter tunnels. Because there is a dire need to develop a system of excavating small horizontal openings at shallow depths without interrupting traffic, it was hoped that a more progress report could be reported at this time. Because of ecological and environmental considerations, laws are being passed which mandate that all utilities be placed underground. In urban areas the excavation of trenches in which these utilities are placed has been done by disrupting the normal flow of traffic, thereby creating complete chaos. In addition, it always seems that the Companies involved have no coordination, since one company completes its installation and another one begins. Certainly, utility tunnels can be driven at greater depths to house main feeder and trunk lines, but there still remains the problem of installing distribution lines for house services. The definition of a "mini" tunnel, is a tunnel whose excavated size is approximately 48 in. or less. The objectives of the Committee are to "stimulate the development of systems and equipment to build tunnels in these size ranges which will reduce costs, time and surface disruption from current systems."

Jan 1, 1974

By Sukumar Bandopadhyay

In recent years planning of surface mines in general and reclamation and post-mining land uses in particular have become very complex. Due to the lack of suitable techniques, land use plans are rarely based upon structured decisions. Data collection may be conducted in a rigorous manner and certain analyses may be performed on the data; the decision to put the land to a specific use, however, is finally based upon the intuitive judgment of one or several individuals. This paper demonstrates how techniques from fuzzy set theory can be used in order to select an optimum post-mining land use plan. The various land use planning alternatives have been characterized according to both qualitative information and quantitative factors and the "fuzzy" aspects of the collected information are incorporated into the analyses. In a practical application, the methodology is used to obtain the most reasonable solution to a post-mining land use planning problem in Interior Alaska.

Jan 1, 1986

By Thomas D. Kaufmann

Introduction Mining has always been sensitive to the fluctuating income of downstream customer industries. The industry is now becoming more vulnerable to booms and busts as economic pulsations increase and demand for mining products shows little or no long-term growth. As the general economy has become more cyclical in the last decade, the capital-intensive primary industries have become more aware that timing as well as preparation of survival plans are vital in investment decisions. Strangely, however, some of us have not yet included the business cycle in our feasibility studies. Cyclic prices and volumes and fluctuations in profits and cash flows do not fit our linear models. The increased cyclical nature of our economy is recent and poorly understood. Forecasting peaks and troughs is still more an art than a science. Nevertheless, avoiding business cycle parameters can lead to error in value estimation and contingency planning of new projects. Metal and Mineral Industries More than half the iron and steel, aluminum, copper, lead, zinc, manganese, tin, nickel, molybdenum, cobalt, and chrome that we mine, smelt, upgrade, and recycle goes to construction, transportation, capital goods, and consumer durable industries. All are cyclical. Their products are consumed slowly, so replacement can be postponed in recessions. Purchases of such goods are usually financed by debt, and their customers are sensitive to highly cyclical changes in interest rates. During prosperous periods, people tend to buy capital goods despite high interest rates. Upstream industries also tend to be whipsawed by inventory cycles. With high interest rates and good transportation, downstream fabricators can lighten their inventories during recessions. They know that upstream suppliers can deliver supplies and raw materials immediately, And, with the advent of electronic accounting, the fabricator with timely inventory information can afford to hold fewer contingency stocks. Likewise, when recovery returns, inventories surge back through industry pipelines, accelerating demands on primary supplies. The price elasticity of most primary products is low. Their share of the value of finished products of the industries they supply is generally small. The 60 kg (130 lb) of aluminum in a car is vital. But whether it costs $80 or $130 will not visibly influence the demand for an automobile. With low elasticities of demand, the primary producer is hit with decreases (or increases) in prices and in sales volume, during recessions as well as recoveries.

Jan 6, 1984

By B. K. Mishra, Partha Chakroborty

Jigs are the most important equipment used in the separation process that exploits the stratification of particulate matter under the influence of hydrodynamic and gravitational forces. Very little is known about the determined mechanisms by which particles of varying density, size, and shape stratify in a moving bed. A model is developed by using the discrete element method to understand the behavior of jig bed. This model is utilized here to study the stratification behavior of the bed and its control. The control action is based on the understanding of the physics of the stratification process within the framework of fuzzy logic. The actions suggested by the fuzzy logic controller (FLC) depend on the current degree of stratification and the existing frequency of the jig cycle. The results show that the FLC achieves efficiency in stratification with minor variations to the jig cycle.

Jan 1, 1995