Search Documents

By Hans Treichl

1. INTRODUCTION For Europe the Arlberg road tunnel signifies the elimination of the largest traffic barrier between Bucharest and Paris in the east-west transversal. Apart from that the tunnel will serve the feeder system to the two north-south links Ulm - Milano, and the Brenner motorway, and links the Inntal and the Rheintal motorways closer together.. Thus, the supraregional road system carrying traffic through the Tyrol and Vorarlberg will considerably be emproved by the Arlberg road tunnel. 2. THE PROJECT The 16.1 km contract section of expressway S 16 includes a ramp section of approximately 2.6 km, the access points at St.Anton and at Langen, and the main 13.98 km section of the road tunnel. This section cuts the link between St.Anton and Langen by 3.7 km, and saves 475 m in altitude. The Arlberg road tunnel is planned to have two tubes with two lanes each. In the first stage the southern tube was under construction. Its traffic capacity is 1,800 car units per hour. The tunnel has a cross section of 9o to 103 m2. The sloping gradients are by 1.3o and 1.67 per cent. Fresh air is supplied and used air removed through a ventilation system, fed at the portals and through two vertical ventilation shafts. One of them, at Maienwasen, is 222 m deep, its cross section 66.5 m2. The diameter in clear is 8.32 m. The vertical shaft Albona is 736 m deep, the diameter in clear is 7.37 m. The tunnels is 9,4o m wide, providing for a 7.5o m roadway plus o.95 m sidewalks on each side of it. 4.7o m above the traffic area the conduits for fresh and used air. A transverse ventilation system with reduced exhaust air has

Jan 1, 1979

By C. A. Johnson, K. F. Unrug

The identification of the major subsidence areas in the Eastern Kentucky Coal Field has been made to distinguish the subsidence phenomena on the basis of geographical location. Further, this identification process is based upon selected critical geological, topographical, and mining features in the coal fields. The proposed identification of the regions is derived from a comparison of the subsidence potential in a particular area. The most likely severe subsidence areas are compared to those with the probable low subsidence severity. The combination of certain geological and mining parameters involved allows for the derivation of a classification of the subsidence potential.

Jan 1, 1986

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Jan 1, 2007

By R. L. Loofbourow

R. L. LOOFBOUROW 26.1-WATER FLOW, USE, EFFECTS, CONTROL Sec. 4 discusses ground water as a mineral resource. This section deals wits its control. 26.1.1-IMPORTANCE Flows of water have an important effect on the cost and progress of many deep excavations. The existence of water limits the methods which can be used in some and presents hazards in others. Lowering the water table may reduce the flow of springs and wells, with legal liability. Some mine water is used directly, some must he treated before discharge, and some contains dissolved solids which can be recovered profitably. Loss of life, property and production from flooding is grim, yet scores of mines have worked safely for generations under ground-water reservoirs, lakes and even the sea. The need for better control of mine water is measured by the severity of recent floodings, concern with the quality of the effluent, and direct and indirect costs of working wet ground. There are improvements in freezing in shaft sinking. pumps and their controls, treatment of mine water before it is pumped, bulkhead construction and certain efforts to reduce inflow. 26.1.2-PUMPING COST VS. COST OF WET WORK Direct operating and capital costs of pumping are more evident than indirect items, such as provision of extra standby power and maintenance facilities, The total of all these items is the cost of pumping water from an excavation. This is only a part of the extra cost of working wet as compared to dry ground. Less productive methods, less efficient equipment and more expensive explosives may have to he used in wet work. Wet rock plugs certain equipment. Maintenance is higher and labor less efficient. The cost of any means of keeping work drier should he weighed against the higher cost of working wet. The true difference in the cost of working wet ground, compared with dry, probably is known at only a few places (see checklist of cost items. Sec. 26.4.13). An extreme comparison of mining wet and dry ore is available from Ambrosia Lake, N.M. (Fig. 26-1). Between 1963 and 1967, a wet and a dry mine were worked by the same company under conditions otherwise comparable. Average operating cost at the wet mine, pumping 1,600 to 1,800 gpm. was $16.06 per ton of ore. The comparable figure for the dry mine was $7.50. Principal differences included the fact that the wet mine was worked from drainage levels below the, ore with rail haulage, the dry mine in the ore with off-track equipment loading and hauling to the shaft. In the wet mine, ore packed in chutes, cars and skips and froze in surface bins, stockpiles and trucks. Wet-mine costs included drilling drain holes, building and maintaining ditches and pumping water containing abrasive solids.

Jan 1, 1973

By Greg Partington, Darryl Thorburn, Charlene Wildman, Elisa Puccioni, Connie Payne, Campbell McKenzie

"Mineral prospectivity modelling of polymetallic nodule deposits has been completed over the Cook Islands Exclusive Economic Zone (CIEEZ) using the GIS based Weights of Evidence modelling technique. Polymetallic nodules, also known as manganese nodules, have been explored as a possible resource for a number of metals including cobalt since the early 1970s. Recent data on the nodule composition and abundance in the CIEEZ has led to a renewed interest in the prospectivity for manganese nodules in the region. The predictive modelling has used the most recently accepted mineral model for polymetallic deep-sea nodule deposition to identify factors that are most likely to map the presence of this type of mineralisation in the CIEEZ.Manganese nodules form on the deep seafloor as concretions formed by concentric layering of iron and manganese hydroxides around a core and they grow at a very slow rate, on the order of millimeters per million years. The available data for the CIEEZ indicates a greater abundance in the area of nodules formed by hydrogenetic processes, which are the result of slow precipitation of metallic components from seawater. The environment in which the nodules are most abundant is at depths between 4,000 m and 6,000 m in areas of low sedimentation rate. Hydrogenous nodules commonly grow on siliceous and pelagic clay sediment, they are less common on other types of sediment."

Sep 1, 2014

By Yao Zhou

Under the United Nations Convention on the Law of the Sea (UNCLOS), the international seabed area (Area) and its resources are the common heritage of humanity (CHH). Patent rights can be incompatible with the CHH doctrine and its underlying principles because patent holders might charge unjustifiably high prices to license patented technology for exploring and exploiting the Area’s resources (creating a "patent holdup" situation), might choose not to license, or might license exclusively when doing so would contravene CHH principles. However, a reasonable patent licensing regime can contribute to sharing the benefits derived from the Area and promote environmental sustainability. Provisions of the UNCLOS that stipulated compulsory technology and financial transfers were removed in the 1994 Agreement relating to the Implementation of Part XI of the UNCLOS but to promote equity and sustainability I propose a voluntary licensing regime modeled on the concept of reasonable and non-discriminatory patent licensing that has been used in other contexts. The International Seabed Authority or another entity will need to coordinate and promote this licensing regime through governance of intellectual property derived from the Area. This proposed approach can better effectuate the CHH doctrine and its underlying principles.

Sep 1, 2014

By C. G. Buttleman, W. C. Brice

In Minnesota, reclamation of active aggregate mining sites is primarily regulated through local permits issued at the county, township, or municipality. However, for abandoned or depleted aggregate mining sites, a responsible party for reclamation is often no longer available. Since 1995, the Minnesota Department of Natural Resources has reclaimed several abandoned aggregate sites using innovative public/private partnerships and emphasizing native plant materials. The purpose of these projects is to demonstrate cost effective reclamation methods that can be utilized by both aggregate operators and local government and to promote mine planning and resource identification as it relates to reclamation.

Jan 1, 2000

By W. C. Meyer

The concept of using powdered coal-in-oil-mixtures (COM) as a composite fuel to conserve oil resources and relieve import supply problems is being vigorously promoted by the Department of Energy via the sponsoring of various demonstration units (1). The idea of COM as a useful alternative fuel has been explored on and off for over 100 years (2). The approach must be capable of grinding, mixing, storing, and combusting COM with presumably only minor equipment changes on oil-fired boilers. DOE estimates that 56 000 m3 of oil (350 000 barrels) could be spared daily if a 50-50 COM was used to generate electricity. Of course, the ability of COM suppliers to prepare and deliver a stable suspension of COM at reasonable economic costs must be achieved if the concept is to be successful. This report reviews the various methods used to attain stable coal-oil mixtures. Various physical-chemical principles associated with each method of stabilization are also discussed.

Jan 1, 1981

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government's cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By A. Yazadni-Chamzini

Considering the nature of open pit mines, harvest volume, it usually is required to remove a lot of waste to access to mineral planned grade. So, one of the most important part of open pit mines design, is waste dump site selection. Many factors are effective in waste dump site selection. These factors are sometimes in conflict with each other. So selecting the desired location for waste dump is a process complex and multi-criteria decision making. There are a variety of methods for decision making under complicated condition, such as fuzzy, Delphi, multi-criteria decision making and Expert system methods can be hinted. VIKOR method, which is one of the decision making multi criteria methods, is useful tool for decision-making. On the other hand with regard to uncertainty in decision-making, fuzzy approach is a useful tool for this purpose. This article has tried to select the best waste dump site in Sari Gunay Gold Mine by Fuzzy VIKOR. The results show that C position has a higher priority than other positions.

Jan 1, 2012

By George O. Lower

The use of cyanides in the extraction of gold and silver is well known.1 Such extractions employ con¬centrations of cyanide in the range of 0.02-0.25 % sodium cyanide equivalent in leaching cycles of 24-48 hours and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold and silver. 2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure. For example, on products in the flotation size range, the major portions (e.g. 65-85%) of the extractable copper frequently dissolved in 2-10 minutes. At coarser grinds, e.g. 100% minus 28 mesh and 100% minus 10 mesh, 75-85% of the total copper was extracted in 30 minutes.

Jan 1, 1966

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels1. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m(26.5 ft) above the miner’s head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roofbeam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

Jan 1, 1999

By Hyung Jeek Kim, Jongmin Joo, Jonguk Kim, Jai-Woon Moon, Kyeong-Yong Lee

"Co-rich ferromanganese crusts (Fe-Mn crusts) distributed on seamounts in the western Pacific are potential economic resources for cobalt, nickel, platinum, and other rare metals in the future. Evaluation and selection of a mining site can be established based on abundance and grade of Fe-Mn crusts in the site as well as topography that should be smooth enough for mining operations. Therefore, acquisition of shipboard echo-sounding and acoustic backscatter data are prerequisite to the selection of potential mine sites in addition to visual and sampling operations. Acoustic backscatter data can be used to locate crust-covered areas on a regional scale with the understanding of acoustic properties of crust through its correlation with visual and sampling data.During an expedition that took place from January to March 2014, KIOST collected geophysical and geologic data to assess the resource potential for Fe-Mn crusts on three seamounts (guyots) in the Western Pacific. In OSM11, one of the three surveyed seamounts, three camera tows were performed to observe the distribution of Fe-Mn crusts on the summit and slopes of the seamount. Although sediments of various thicknesses generally cover most of summit region of OSM11, several regions with high backscatter signals occur on the periphery of the summit. The occurrence of Fe-Mn crusts, observed during the camera tows, on those high backscattered regions suggests that the backscatter signals of shipboard multi-beam sonar can reflect changes in the geology of the seafloor from sediment layer to Fe-Mn crust deposits. The Fe-Mn crust deposited around the summit region is worthy of notice because of its topographic characteristics, including shallow depth, flat or gentle inclined surface, and smooth relief, which are more suitable for mining operation compared to the flanks of seamount."

Sep 1, 2014

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 3, 1985

By L. K. Bandyopadhyay, P. K. Mishra, S. K. Chaulya, R. S. Singh, A. Kumar, N. Tripathi, K. Mandal

A comprehensive field study has been carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling has been carried out to envisage dust concentration due to the existing and closed mines in the region. The predicted total PM10 and PM2.5 levels at the selected receptor locations ranged from 86.39 to 194.89 and from 34.82 to 99.55 µg/m³, respectively.

Jan 12, 2022

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.

By F. Nelson

RJB Mining is the largest coal producer in the UK. In January 1995 the Company acquired the Central North and Central South Regions of British Coal consisting of: ? 15 operating collieries -including capital equipment ? 2 care and maintenance mines ? 16 operating Opencast sites ? Interest in 26 prospective and 46 potential Opencast sites ? Approximately 417 million tonnes of proven and probable reserves and considerable mineral resource ? 9 million tonnes of coal stocks ? Long term contracts to supply approximately 90 million tonnes of coal to National Power and PowerGen to the period of 3 March 1998 ?Approximately 7,600 employees and 4,500 mining contractual labour. Up to the acquisition RJB Mining had the capacity to produce 14 million tonnes of saleable output with an approximate 1,500 strong workforce.

Jan 1, 1998

By James Warner, Peggy Ganse, Glen Smoak, Raymond Henn, Sam Bandimere

Over the past several decades, cement-based grouts using ultrafine cement as are placement for portland cement have begun to gain acceptance as an alternative to chemical solution grouts, however the amount of information currently available on these grouts is limited. For this reason, the authors developed a field testing program to evaluate the penetration capabilities of various ultrafine cement grout mixes. The tests were conducted by injecting sand columns using different portland and ultrafine based grouts, the measuring penetration distances after applying equal injection pressure for the same time period. Results of tests performed in 1999 and 2000 are discussed herein.

Jan 1, 2001

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

By J. A. Botín

In modern mining, the core of mine planning and design is the block model, a simplified representation wherein the ore deposit is divided in a number of virtual rock cubes, each characterized by technical and economics parameters. Mining engineers use this model to design the mine and develop production schedules. Traditionally, sustainability issues are not considered in the mine design, planning and engineering processes but rather are incorporated in the later stages of the feasibility evaluation as necessary expenditures and operating costs. This paper describes the results of a research project aiming to develop a methodology to incorporate sustainability parameters directly into the block model, so that they become an integral part of the design, planning and scheduling processes. It is considered that the incorporation of sustainable parameters into the block model would yield a more responsible mine design and improve mining projects sustainability performance

Feb 27, 2013