Search Documents

The MINER Act of 2006 mandated that all underground coal mines must install and maintain refuge chambers. Refuge chambers serve as a temporary shelter in case of emergency. Several factors affect the performance of a refuge chamber: heat production inside the chamber and introduction of CO when chamber doors are opened are two major factors. This study examines the CO purging process and to determine total air quantity and time necessary to lower the CO con-centration to safe levels for different inlet/outlet configurations using three-dimensional simulation technique. The study uses Reynolds Averaged Navier Stokes and continuity equations along with the spe-cies transport model assuming uniform air mixing. The heat transfer of any kind is neglected and the purging process is assumed to take place isothermally. The standard k-e model is utilized for simulating turbulence in the flow field. This research provides useful guidelines in developing an efficient strategy for purging refuge chamber. Keywords: Airlock chamber, Purging, Carbon monoxide, Turbulence

Feb 27, 2013

By Michael Feroz

Severe drought in the Colorado River Basin over the past 10 years has caused water levels to drop in Lake Mead by more than 113 feet. The current lake level is at elevation 1,112 feet mean sea level (msl). Lake Mead is the primary source of water supply for greater Las Vegas. Water for Las Vegas from Lake Mead is accessed through two existing submerged intake shaft and tunnel systems. If the water levels continue to drop in the lake, the Intake No. 1 will become inoperable below water level elevation of 1,050 feet msl. To sustain the current levels of water delivery to all member agen-cies in the southern Nevada region, the Southern Nevada Water Authority (SNWA) has decided to construct a third intake at a deeper depth in the lake to ensure better quality water and enhanced reliability.

By C. L. Jiang

The selective depression of pyrite obtained from Kentucky No.9 seam in coal flotation with various kinds of inorganic and organic chemicals was systematically examined. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates has been explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta potential measurements. It was shown that pyrophosphate reacts strongly with iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1998

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

By James Paone

Drillability of rocks by mechanical means is closely related to the physical properties of the respective rocks, Various approaches by previous investigators on rock drillability are presented, as well as recent techniques studied by the Bureau of Mines. The studies show drillability concepts based on (1) theoretical drilling equations derived from laboratory drilling experiments extended to field drilling results and on (2) a statistical method where multiple regression analysis is used to develop a prediction equation for drillability.

Jan 1, 1966

By J. Kretschmann, R. Amiri

"The Sangan iron ore mines (SIOM) in Iran are located in a remote area near the Afghanistan border. The SIOM deposit contains a geological resource of 1.1 Gt (1.2 billion st) of mostly magnetite with an iron (Fe) grade ranging from 27 to 61 percent. The Iranian government plans a stepwise development of SIOM in cooperation with private companies to satisfy the growing demand of the Iranian steel industry. Sustainable development is an influential ethical concept in mining all around the world. However, a successful realization of a sustainable development plan is not possible without a foundation on the core values and regarding the specific circumstances of the individual mining country. This paper introduces SIOM and describes sustainable development activities undertaken during its development. From the early stages, these activities have been realized to secure the acceptance of the stakeholders in the region. To evaluate their effects, indicators were filtered to the ones with the highest priority for the stakeholders. Moreover, Islamic values and Iranian regulations and their influences on SIOM were analyzed.Mining industry in Iran The Islamic Republic of Iran holds 68 types of minerals, including salt, sand and gravel, gypsum, chrome, lead, zinc, copper, coal, gold, iron, etc., with 33.5 Gt (37 billion st) of proven reserves and more than 51.7 Gt (57 billion st) of potential resources. Iran is ranked among the 15 major mineral rich countries (1). In accordance with the statistics published by Statistical Center of Iran (SCI), there were 5,316 active mines and 84,922 employees in the whole country in 2012-2013 (2) and, according to the statistics published by Central Bank of Iran (CBI) in 2011, the share of this sector in the gross domestic product (GDP) of the country was 1.2 percent (3)."

Jun 1, 2016

By M. Alley, P. Schroeder, L. Zelazny, S. Nagle

The Old Hickory mineral sands ore body in Virginia (>2000 ha) currently supports a productive rowcrop agriculture. Reclamation experiments were implemented on pilot-scale mining pits from 1995 to 1998. Half of each mining pit was topsoiled (25 cm) while the remaining half was left as either (1) mixed tails/slimes or (2) re-graded subsoil over tails/slimes treated with 112 Mg/ha yardwaste compost. Post-mining productivity was estimated to be reduced by 23%, 3%, 27%, and 20% for each crop (wheat/soybeans/corn/ cotton) in sequence when compared to undisturbed soils. Variability in surface texture and compaction limit restoration of soil productivity.

Jan 1, 2002

By Bruce Hebblewhite

Australia’s Minerals Tertiary Education Council (MTEC) has achieved several successes during its first three years of operation. This initiative was developed through the Minerals Council of Australia, in conjunction with three partner universities involved in mining engineering education. The partner universities are the University of New South Wales (UNSW); Curtin University, the West Australian School of Mines (WASM); and the University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and the development of a number of flexible, distance-based delivery programs. This article then discusses future initiatives. Importantly, the challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering: Mining Education Australia (MEA). This will provide a common third and fourth year program to all three universities beginning in 2007. The common program will involve innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process.

Jan 1, 2006

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

By William R. Yernberg

The 2002 Arizona Conference was held Dec. 8 and 9, 2002, at the Doubletree Hotel at Reid Park in Tucson. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The meeting featured a keynote address, a distinguished lecture and about 30 technical papers. As was the case at the 2001 meeting, the economy, the price of copper and foreign competition continue to be the hot topics of discussion among the attendees. The domestic copper industry still faces challenges due to low copper prices dictated by the world market and because of a weakened domestic economy. There continues to be concern about the Arizona region’s copper industry in light of the mergers, downsizing and shutdowns that have occurred during the past several years.

Jan 1, 2003

By Brian E. Gombos

During early stages of the detailed design for Detroit?s Upper Rouge CSO Tunnel Project, a Value Engineering Recommendation suggested the design team investigate alternative concepts to the usual cast-in-place or precast concrete lining system for the Project?s many smaller diameter Deaeration Vent Shafts. The resulting design investigation produced not only an alternative lining system, but lead to a proposed non-conventional approach to shaft installation means and methods through soil and rock necessary to construct the permanent shaft lining system. This paper will outline and summarize the technical issues, contractual restrictions, and cost considerations that eventually lead to the final shaft design

By D. J. Barratt

The application of autogenous and semi-autogenous grinding circuits in recent years has contributed toward substantial savings in capital and operating costs compared to conventional circuits, particularly for large scale copper and molybdenum operations. Such savings have been realized from the deletion of operating, maintenance, equipment purchase and substantial civil/structural costs associated with secondary-/tertiary crushing and screening, fine ore storage and conveying. In spite of the downturn in the copper- moly industry in North America, there is still an interest in autogenous and semi-autogenous grincting for copper-zinc, gold and silver ores and in the overseas market. Both single-stage and two-stage circuits are in operation. Primary circuits operate autogenously or semi-autogenously in either open or closed-circuit. Critical sizes are extracted and crushed for recycle in some cases (e.g. ABC circuit). Secondary grinding is conducted using ball mills or pebble mills.

Jan 1, 1985

By Jack M. Campbell

The regulatory process by which governmental authorities acknowledge and, in turn, permit the location, construction, and operation of large scale energy-related facilities has become extremely detailed in recent years. One example of the detail that is entailed in the regulatory process is the number of permits that must be acquired by operators prior to the construction and operation of energy-related facilities. It has been estimated, for example, that 75 permits are required prior to the opening of a new coal mine in Pennsylvania while 50 are required in Kentucky. From the perspective of facility owners and operators the regulatory process often appears overly complex and may be perceived as a constraint to the corporate decision making process. From the perspective of those responsible for administering regulations, the process is perceived as a mans by which public desires - pursuant to social objectives such as environmental protection and occupational safety - can be achieved. As a result of conflicting organizational interests, the clash between energy facility owners and operators and their regulators appears to be inevitable. Furthermore, the resolution of this conflict lies in the tradeoff between objectives and the costs of regulation. The balance of objectives and costs is a subject of the political process and not a topic of consideration in this paper. This paper is concerned with the actual administration of regulations, that is, the implementation of that which arises from the interplay of organizational interests. The paper assumes that environmental control laws will not likely be repealed, that regulations to implement the intent of these laws are here to stay and thus the paper seeks to assess how regulations are administered at various levels of government pursuant to objectives. The paper hypothesizes that the administration of objectives (or policy) has an impact on decision making which affects energy facility decision; making while recognizing the fact that regulatory policy cannot be totally divorced from administration, this paper proceeds

Jan 1, 1977

The 18th annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held on Saturday, Dec. 2, 2000 at The Westin La Paloma in Tucson, AZ. The 2000 inductee, guest of honor and featured speaker at the banquet will be Ronald C. Cambre, chairman and chief executive officer of Newmont Mining. He will be honored for his role in positioning Newmont as an innovative and key player in the gold mining industry.

Jan 1, 2000

By E. Topuz, C. Patrick

Longwall face-to-face transfers can cost more than $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high costs make extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. Operations research techniques are used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate, over 35%, of the total US longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation was used to generate models of transfers under Carving conditions; and the economic feasibility of tine-cost tradeoffs in the transfer procedure was investigated.

Jan 1, 1994

By Peter Zhang, Mark Van Dyke, Ted Klemetti, Morgan Sears

Room-and-pillar mining is a mining method used in the United States to extract coal from underground, and pillar recovery is widely practiced for maximizing coal recovery and mining economics. Under certain conditions, room-and-pillar mining can create high stresses in coal pillars resulting in a coal outburst. These outbursts represent one of the more severe safety hazards in underground coal mines, potentially causing injuries and fatalities. Over the past ten years, coal outbursts have resulted in three fatalities in U.S. room-and-pillar mines. Though coal outbursts generally occur under deep cover, they are more likely to occur during pillar recovery and under multiple-seam mining conditions. Coal outbursts are generally associated with strong roof and floor and heavy loading of coal pillars, but it is difficult to predict whether, where, and when they will occur. In this respect, risk management provides a proactive tool to prevent coal outbursts in room-and-pillar mining by identifying mining areas with high risk of outburst and mitigating the risk accordingly.

Apr 26, 2022

By Michael Gilbert

In the world of tunneling the glamour is in the large diameter, long tunnels, but perhaps the number of projects for small diameter and short length tunnels are greater and generally have higher risk factors. Reasons for these higher risks include both the ?boiler plate? contract provisions used on these types of contracts, the technical specifications related to the tunnel work (versus the pipeline construction), the bid practices including measurement and payment and the construction. This paper reviews and comments on some of the key issues the authors have observed in recent major pipe-line projects that involve a small percentage of tunneling footage of the total contract.