Search Documents

By Wern-ping N. Chen

Pressure tunnel includes water-supply tunnels and tunnels for hydroelectrical power plants. Their design principles are different from those of water/wastewater/conveyance and transportation tunnels. Though theoretical pressure tunnel design guidelines exist, a comprehensive guide to summarize these guidelines to facilitate the planning and design of a pressure tunnel program is lacking. The purpose of this paper is to fulfill this need. It first provides key pressure tunnel design concepts in hard rock environment; then, it illustrates associated final lining design principles, including the design of un-reinforced concrete lining, steel lining, and reinforced concrete lining. Design diagrams and a flowchart for the reinforced concrete lining design are provided.

Dec 1, 2022

By E. Stemn

Incident investigation is of utmost importance in most high-risk industries. This study was undertaken to study the content of past investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of 5 elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of 3 Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed. INTRODUCTION The importance of learning from incidents is well documented in the literature. For instance, some scholars regard learning from incidents as important for improving safety [1,2]. Thus, many organisations spend considerable resources in identifying lessons from incidents and subsequently on the process of improvement that follows the identification of lessons. It is therefore important for such organisations to determine the effectiveness of their learning from incidents processes, in order to identify specific areas where improvements are needed, so that interventions can be as specific as possible. The learning from incidents process models the plan-act-check-do approach of management systems, often consisting of four major stages, namely; data collection and incident analysis, planning interventions, implementing interventions and follow-ups and evaluation [3,2]. The investigating and analysis of incidents have been regarded as one of the vital stages of the learning process since it is the stage where lessons are identified [3,2,4]. It has also been noted elsewhere in the literature that results of the previous stage of the learning process are important for the next stage [3]. For example, ineffective incident analyses could result in the planning of ineffective remedial measures. One of the primary aims of incident investigations is to identify lessons from previous incidents which when implemented can prevent future recurrences or minimise the effects of future incidents. There is thus the need for organisations to assess the quality of their investigations periodically since it is one of the means they adopt to improve safety and the quality of remedial measures to some extent depends on the effectiveness of the investigations. Although previous studies [5,2] have assessed the effectiveness of the learning process, and some aspects of the learning process, such as incidents reporting, there is less focus on the effectiveness of incident investigations. The research described in this paper was therefore conducted to contribute to this gap, focusing more closely on incident investigation reports.

Jan 1, 2019

By Andrew J. Petruska, Rik Banerjee

This study explores implementing a machine learningbased system to generate a 3D surface repre- sentation of the roof and support straps in the mine. Event cameras have been chosen for their performance in high-dynamic-range lighting conditions and for their low latency. To enable automated drilling and bolting, 3D vision using eventbased cameras has been developed. A ground-truth set is created using two, time-synced event cameras and a LiDAR camera. These sensors are used to construct a ground-truth dataset of corresponding event- camera images and surface maps from the LiDAR. The network is tested with stereopairs of event images and produces a depth image with ±5 mm RMS error on average across 1000 test images.

Feb 1, 2024

By S. Deming

Coal is China's main source of energy. In 1988, 76.1% of commercial energy consumption was supplied by coal. To provide a rational utilization of its coal resources, China has paid considerable attention to coal preparation over the last 10 years. In 1980, there were only 105 washeries treating about 100 million tonnes of coal, but by 1988 there were 151 washeries treating 171 million tonnes per year. This paper describes the development of China's coal preparation industry; its growth, the equipment, and the technology. Statistics and information on the current status of the industry are also be presented.

Jan 1, 1991

By Kenneth L. Maloney

Ten small and intermediate-sized [11 GJ/hr to 264 GJ/hr (10,000 lb/hr steam to 250,000 lb/hr steam)] coal-fired boilers in the upper Midwest have each been tested on both a bituminous eastern coal and a subbituminous western coal. The purpose of this study was to determine the feasibility of substituting western subbituminous coal for eastern bituminous coal as a means of reducing the SO x emissions from this class of boiler and to demonstrate the feasibility of greatly expanded western coal utilization as a means of reducing the use of oil and gas. The scope of this study was such that the representative boiler types were tested on both eastern and western coal for a period of time sufficient to completely characterize their individual emission and operational characteristics.

Jan 1, 1977

By Phil Shelton

What exactly does clean coal mean? Mining coal creates dust and releases methane gas. And burning coal liberates CO2 and emits particulates, including SO2 and NOx. Coal creates wastes that are often stored in unsightly and potentially dangerous slag heaps and lagoons. When clean coal technology is discussed, it sometimes seems that creating modern or ?ultra super critical? coal-fired power stations is presented as the main or even the only answer. However, there may be a more holistic approach. Using the energy potential of coal is always going to have environmental impacts. Some of these will be negative. But the need to secure future energy resources demands that society tackle these negative issues and find ways to minimize and offset them.

Jan 1, 2010

By Jack T. Work

Spiraling costs in every segment of the open-pit mining cycle is a fact of life that every operator must reckon with. The introduction of various shock absorbing devices for rotary drilling is one recent innovation that may significantly reduce overall drilling cost, increase drill availability, and lower maintenance requirements. In a recent all-inclusive test in taconite ores, shock absorbers on Bucyrus-Erie BE 60R and Gardner¬Denver GD 120 rotary drills were directly responsible for overall savings of up to $41.06 per hour. What is It? A shock absorber is simply a device installed between the rotary drive head and drill steel that cushions the two. It functions in the same manner as springs and shocks on an automobile. Some benefits associated with use of the tool are readily apparent on a daily basis; other benefits are realized over longer time intervals and through continued use. A properly designed shock absorber will: •protect the drill from severe vi¬brations, improve rock bit performance, allow application of the best weight-on-bit and rotating speed under all drilling conditions, •function effectively over a wide range of applied bit weights, • have a spring rate soft enough to perform its primary function of absorbing both rotary and vertical vibrational forces generated by rough drilling, •be reliable and subject to as little maintenance as possible, •be easy to install and remove, and • be of such an economic benefit so as to offset the added expense of its application. A shock absorbing tool developed by BJ-Hughes Inc. was used in a recent test. The "Smoothdrill" is just one of the products currently available. This unit absorbs both rotary and vertical shock loads and has no mechanical parts so lubrication is unnecessary. A rebuild of the unit consists of removing the worn rubber element and inserting a new element, an operation taking less than one hour. Minimizing Vibrations Severe vibrations on a blasthole drill operating in broken and discontinuous formations have visible effects. These vibrations often cause structural damage when allowed to' continue, resulting in fatigue cracks in the mast and related structural components in the drill. When rough running formations are encountered, drilling must be interrupted and possibly shut down. Usually, the drill operator resumes drilling using less down pressures and various rotational speeds until firmer drilling is encountered. An effective shock absorber can substantially reduce these vibrational forces so more down pressure can be applied in bad ground. It is generally accepted that longitudinal vibrations and cyclic forces are more effectively reduced if a tool is designed to incorporate a relatively "soft" shock absorber. The softness of any shock absorbing tool is best judged by its spring rate-the weight required to produce a given amount of deflection, commonly expressed in units of kg per mm or pounds per inch of deflection. All shock tools use a resilient member such as rubber springs, steel springs, fluid, or gas springs to absorb

Jan 4, 1980

By David E. Siskind

The Bureau of Mines has studied the problem of cracking in residential structure walls from vibrations produced by blasting in surface mines. Direct observations were made of blasting damage consisting primarily of cosmetic cracking in plaster and gypsum board walls. Measurements of structure response and also application of the response spectra analysis single-degree-of-freedom model were used to quantify the frequency dependence of the safe level criteria. An overall summary analysis was performed using the new Bureau of Mines damage observations and data obtained from nine previous studies, including the three analyzed earlier by the BuMines for Bulletin 656, published in 1971. Separate analysis of the high- and low-frequency damage cases, structural response, and two types of construction resulted in the establishment of safe vibration levels ranging from 12 mm/sec to 50 mm/sec (0.5 in/sec to 2.0 in/sec).

Jan 1, 1980

Invensys’ recently introduced Field Device Manager for Foxboro I/A Series distributed control systems provides the industry’s first solution that takes advantage of both the latest Enhanced Electronic Device Description Language (Enhanced EDDL) and FDT technologies. This combination provides comprehensive lifecycle support to configure, calibrate, commission, diagnose and optimize the performance of any vendors’ foundation fieldbus device. The I/A Series Field Device Manager enables users to take advantage of any EDDL, Enhanced EDDL and/or FDT host deliverables supplied by the device vendor.

Jan 1, 2007

By Bob Rautenberg, Luminita Calin

The Tunnel and Reservoir Plan (TARP), commonly known as the Deep Tunnel Project, was developed by the Metropolitan Water Reclamation District of Greater Chicago as a two-phase solution to the problem of waterway pollution and basement flooding due to sewer system backups created by the combined sewer overflows. With only one contract left before completion of the Phase I tunnels—the 12.4 km(7.7 mi.) long Little Calumet leg—the pollution control phase of the 175.7 km(109.2 mi.) long system will be 93% complete, once the Torrence Avenue tunnel project comes to an end. This paper describes the Torrence Avenue tunnel project, currently under construction by the joint venture of Kenny (Sponsor) / Kiewit / Shea. Mining of the10.4 km (34,151 feet) long and 8.3 m (27'-4") diameter mainline tunnel was completed in a record thirty-one-weeks period and the concrete lining is nearing completion. Details on the complete muck handling system, numerous mining and concrete lining records will be given.

Jan 1, 2001

By Robert G. Lundquist

REAM (for Rapid Excavation And Mining) is a method of rock fragmentation by high-velocity projectile impact developed by Physics International Company. This paper reports the results of field testing over the last two years. The success of the method is based on the fact that the amount of rock broken per shot scales nonlinearly with projectile impact energy. Thus, high energy impact yields spectacularly low specific energies for rock breakage. The field work reported used 90- and 105-mm military guns to accelerate 8-1/2 and 10-pound concrete and steel projectiles to velocities of 5000 to 5500 fps. All tests were performed in a competent 25,000 psi granodiorite at Hope Valley, California. During the first year of field testing 26 feet of 13-foot-diameter tunnel were produced with the 105-mm gun. The first 20 feet of this tunnel were line-drilled to aid in producing a stable portal. During the second year the tunnel was extended an additional 29 feet using the 90-mm gun. The 55-foot tunnel was produced by 590 shots. Between 1-1/4 and 1-1/2 tons of granite were broken by each shot. A silenced 90-mm gun was placed underground and the tunnel portal closed with a steel barrier. Overpressures of less than 1 psi were measured on the inside of the barrier, corresponding to an impulse noise of about 170 db. The muck produced was similar to drill and blast muck. Overbreak and ground support problems appeared to be less than with drill and blast. The contour of the tunnel was easily controlled using the 90-mm gun; the tests were also conducted using a 57-mm gun for trimming. Projections indicate that advance rates with REAM will be three to seven times faster than drill and blast, at less than two-thirds the cost. This is based on the development of a fully integrated continuous system and an inexpensive propellant giving a total expendables cost of less than $3 per shot. Other applications of the REAM technology are found in secondary breakage for open pit mining, in drilling large diameter holes, and in underground mining for longwall mining, overhand stoping, and raising.

Jan 1, 1974

By W. G. Pariseau

"The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to the start of mining in the south barrier pillar. Subsequent loss of ground control in August 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterward three rescue team members. A U.S. Mine Safety and Health Administration (MSHA)report describes the events in detail (MSHA, 2008).An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools and selecting the right tool for the job is essential. In this regard, minimum program requirements include capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses.The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two-dimensional finite element analysis indicated pillar safety was by no means assured (MSHA, 2008; Pariseau, 2008; Pariseau, 2011). Geometry of barrier pillar mining is limited in two dimensions for example, crosscuts are not seen in vertical cross sections. While three-dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three dimensions. This technique involves a dual node - dual mesh concept. Both have been used separately in much earlier work, but are only now used in combination. It is possible to have an estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale (Pariseau, 2014). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2014

By A. A. Dor

Recent developments in the design of concentration plants have reflected the increased recognition that has been given to the economic and metallurgical advantages of autogenous grinding. This has manifested itself in the increasing adoption of primary auto genous grinding in iron ore 'beneficiation plants in North America. Table 1 lists eleven major iron ore beneficiation plants which have either been put in operation since 1961 or are under construction at present. Seven out of these eleven plants have adopted primary autogenous grinding. Four of them have coarse grinding mills (8 to 14 mesh) and three have fine grinding primary circuits (48 to 65 mesh). Their nominal capacity totals 26. 2 million ltpy of concentrates or pellets, representing very nearly 75% of the aggregate capacity 135. 3 million ltpy) of the eleven concentrators listed. For a long time there was a tendency to consider that primary autogenous grinding was only applicable to suitable coarse grained ores, However, extensive testing of a very wide variety of ores, and actual operating performance in several commercial plants, seem to have established beyond reasonable doubt, that the majority of mineral ores which the beneficiation engineer may be called upon to process can be ground autogenously. The basis for the selection of autogenous or conventional grinding mills, becomes principally economic and depends on the liberation characteristics of the ores under consideration and their relative hardness and grindability.

Jan 1, 1965

By T. B. Thompson

The Leadville District has been a prominent metal producer since its discovery in 1860. Veins and replacement bodies both have contributed to district production. The latter have been the major metal sources and are hosted within the Paleozoic Leadville, Dyer, and Manitou Dolomites. Igneous bodies representing eight separate events cut the sedimentary section. The main intrusive complex within the district occurs in the Breece Hill area and was the thermal center about which the vein and replacement ores exhibit mineralogical zoning. Precious metal-pyrite-quartz veins (quartz Th= 422 to 469°C; salinity < 4.2 wt. percent eNaCI) occur within or peripheral to the Breece Hill Intrusive Complex, whereas base metal veins and replacement bodies extend from the complex margins outward as much as 2 mi. Pre-ore and post-ore igneous bodies occur, but Fragmental Porphyry dikes immediately post-date the ore event. The Fragmental Porphyry grades downward from a heterolithic breccia with rock-flour matrix to one with a dark, glassy, sulfide- and phenocryst-bearing matrix, commonly with quartz-feldspar porphyry selvages on the dike. Two types of replacement bodies are recognized in the district: 1) the Leadville-type (LTM), massive sulfide (> 60% sulfides) bodies with recoverable Zn, Pb, Ag, and Au, and 2) the Sherman-type (STM), sulfide bodies (low total sulfide) with barite, galena, sphalerite, argentian tetra.hedrite, and minor pyrite. The latter type occurs only within the Leadville Dolomite and is found throughout the Mosquito Range and extending into the Alma District. The Leadville-type replacement bodies are zoned with a pyritic margin and base metal core. Wallrock alteration and trace Pb-Zn dispersion are strongly developed in igneous wallrocks but are weakly developed in carbonate wallrocks. Cu:Zn, Ag:Zn, and Au:Fe ratios increase outward from the center to the margins of LTM. Some of the sulfide bodies are localized on earlier-formed magnetite skarns. Pyrrhotite, pyrite, and marcasite are the earliest formed sulfide phases while chalcopyrite, marmatite, and galena developed later. Tetrahedrite and electrum occur in vugs and fine veinlets cutting the sulfides. Late-stage barite, dolomite, and fluorite occur as minor phases. Pressure-corrected Th for quartz (375-410°C), sphalerite (374-387°C), barite (320-360°C), and dolomite (310-314°C) fluid inclusions with salinities < 5.2 wt. percent eNaCI characterize the fluid responsible for the formation of the Leadville-type orebodies. These values clearly demonstrate the high temperature and low salinity of the ore fluids. Sulfur isotope analyses for galena and barite from LTM are - 1.9 to + 0.9%o and 7.8%o, respectively. Proximity to feeder veins and favorable dolomite hosts are the principal controls on ore localization. The Sherman-type bodies are not internally zoned but commonly have host rock silicification near the orebody margin or in the footwall rocks adjacent to fluid flowpaths along faults. Early quartz, pyrite, dolomite, and white barite precede base metal-silver minerals which are followed by late quartz and golden barite. It is not clear whether the early quartz and the late quartz and barite are part of the STM-forming process. Fluid inclusion analyses yield trapping temperatures as follows: early quartz, 316-341 °C; barite, 264-347°C; low-iron sphalerite, 215-265°C; and late quartz, 260-278°C. All inclusion fluids have salinities < 8.1 wt. percent eNaCI. Sulfur isotope values for barite and galena from STM range from 13.2 to 24.00/00 (avg: 18.4%o) and -6.8 to -3.8%o (avg: -5.5o/00), respectively. A hydrothermal fluid d34SSS of about 15%o is needed in order for galena and barite in equilibrium to exhibit the observed sulfur isotope compositions. Equilibrium sulfur isotope fractionation between barite and galena indicates a 300°C temperature of deposition. Two separate hydrothermal events appear to have taken place to form the distinctive Leadville-type orebodies and those of the Sherman-type assemblage. The STM is known to be older than the LTM. The latter is likely mid-Tertiary in age, post-dating emplacement of the Johnson Gulch Porphyry. LTM is clearly related to meteoric leaching of sulfur and lead (and other metals) from the upper portions of the Breece Hill Stock. Fluids were transmitted along faults, bedding planes, and contacts, and cooled away from the intrusive complex. Early ore fluids were weakly acidic and developed argillic assemblages in the igneous rocks adjacent to the fluid conduits. Reaction/replacement of carbonate rocks occurred where fluids encountered dolomite, but rapid neutralization prevented any wide-spread alteration beyond the ore-carbonate host contact. Pressures based on sphalerite geobarometry and stratigraphic reconstruction were 1.0-1.2 Kb. The high temperatures of vein and replacement ore fluids indicate that chloride complexing was more effective in metal transport than bisulfide complexes. Cooling, dilution of ore fluids, and reaction with carbonate rocks were the major factors in LTM ore deposition. STM formed over wide expanses of the Leadville Dolomite terrain adjacent to (and possibly capping) the Sawatch uplift. Sedimentary sulfur was derived from Pennsylvanian evaporite-bearing sequences adjacent to the uplift. Ore leads are strongly radiogenic (J-type) and are compatible with a crustal-leaching model. Temperatures of ore formation are higher, and ore-fluid salinities are lower than Mississippi Valley-type ore fluids. Superimposed upon dark-gray, diagenetic Leadville Dolomite are several stages of hydrothermal dolomite regionally distributed astride intrusive centers of the Colorado Mineral Belt. The presence of these later dolomites argues for dolomitization and later ore deposition in response to an abnormal thermal gradient caused by emplacement of Laramide batholiths and their generation of convective flow of meteoric fluids.

Jan 1, 2013

By I. Douni

The aim of this study is to synthesize hydrated compounds of calcium silicate (tobermorite) using as siliceous source perlite milling process wastes, containing more than 70% of SiO2. Calcium silicate hydrates are mainly used for construction of lightweight building materials, plasters, tiles and filters. The effect of temperature, time and particle size of perlite on the quality and composition of the solid product was studied. The solid products were characterized by X-ray Diffractometry, Differential Thermal Analysis and the amount of Acid Insoluble Residue. The synthesis of tobermorite was per-formed by the hydrothermal treatment of perlite waste with a saturated calcium hydroxide solution at a molar ratio CaO/SiO2 of 1, liquid to solid ratio 10 mL/g and 1% w.t. NaOH addition. Three experimental sets were performed. In the first series of experiments the synthesis temperature was kept constant at 205°C while the synthesis time varied from 0.5 h to 24 h. In the second experimental series the synthesis time was kept constant at 2 h while the temperature varied between 150°C and 245°C. In the third experimental set the temperature was 205°C and the reaction time was 2 hours and two perlite waste size fractions were used, a coarse (d50=18 µm) and a fine grained one (d50=8 µm). Reaction products consisted of semicrystalline calcium silicate hydrate (I) and crystalline Al-substituted tobermorite or a mixture of both. An isomorphic Si4+ ions substitution with Al3+ ions in the hydrated calcium silicate lattice was detected by thermal analysis. The experimental results show that good quality crystalline Al-tobermorite can be produced after 6 hours of autoclaving at 205°C or after 2 hours of hydro-thermal treatment at 225°C. Generally, the in-crease of synthesis temperature or time favors the crystallization of calcium silicate phases and enriches them in aluminum. The use of fine grain size perlite is more efficient for the hydrothermal synthesis of calcium silicate hydrates.

Jan 1, 2006

By Hernan Fernandez, Khalid Saif F S Al- Khayareen, Volkan Salepciler, Jacek B. Stypulkowski

Wakrah and Wukair Drainage Tunnel, WWDT is 13 km long with a 4.5 m ID sewer water tunnel about 50 to 60 m below ground surface. Integral to the project are several adits with provisions for future connections as well as four work shafts, four intermediate access shafts, ancillary hydraulic structures, and an Odor Control Facility. The shaft depths range from 50 to 60 m. The project is constructed in aggressive ground with aggressive ground water. The construction activities require years of pumping and disposal of the ground water during tunneling operations as well as construction of permanent structures in shafts. Grouting of the corrosive rock mass in corrosive groundwater for the WWDT has been described in detail.

Jun 23, 2024

By Milos Krofta, Donald B. Aulenbach, James P. Van Dyke

INTRODUCTION An innovative Ø.1-MGD (378.5-m3/day) biological and phyicochemical wastewater treatment system at Hancock, Massachusetts, USA, has been treating the domestic sewage generated from the four-season Jiminy Peak timeshare resort since 1985. The influent raw sewage is collected and equalized in an equalization tank, then biologically treated by two rotating biological contactors (RBC). A portion of the RBC effluent is discharged to a secondary sedimentation tank to simulate conventional waste treatment by a conventional RBC system. For parallel treatment the remaining portion of the RBC effluent is discharged to an innovative Sandfloat (SASF-8) clarifier to simulate a two-stage biological and physicochemical treatment by RBC-Sandfloat. Both secondary sedimentation effluent and Saandfloat effluent are later combined together and discharged to a tertiary sand filter and two UV disinfection&apos;units for final polishing. The operation and performance data of Jiminy Peak plant in the period of May 1985 to March 1988 was fully documented in the Lenox Institute technical report No. LIR/Ø3-88/292 (391 pages, March 1988). This report presents only background information and complete plant data in the period of April 1988 to January 1989. Dr. Lawrence K. Wang and Mr. James P. Van Dyke have been the Consulting Engineer and Director of Special Projects, respectively, for the Jiminy Peak Project since 1985. (Key Words) Innovative and Alternative Technology, Rotating Biological Contactor, Sandfloat, Dissolved Air Flotation, Sedimentation, Tertiary Filtration, Ultraviolet, Disinfection. BACKGROUND INFORMATION Jimmy Peak, Inc., Hancock, Massachusetts, has designed and constructed a secondary wastewater treatment system consisting of preliminary/primary treatment facilities, two rotating biological contactors, a dissolved air flotation clarifier, a secondary sedimentation clarifier, a sand filter and two ultraviolet (UV) disinfection units. Total average wastewater flow is approximately Ø.1 ) (378.5 cubic meters per day). In accordance with the Consulting Engineer&apos;s preliminary design, the total wastewater stream is initially collected and equalized by an equalization tank, and then biologically treated by rotating biological contactors (RBC). Part of the RBC effluent is diverted to a Krofta Sandfloat (SASF-8) for physicochemical clarification in order to simulate an innovative RBC-Sandfloat two-stage waste treatment system. The remaining part of the RBC effluent is diverted to a sedimentation tank for secondary clarification in order to siumulate a conventional secondary RBC-sedimentation waste treatment system for the purpose of parallel comparison. Both Sandfloat effluent and sedimentation effluent are later combined together and discharged to the subsequent sand filter and UV disinfection unit for final polishing. Figure 1 shows the flow diagram of Jiminy Peak Plant. The Massachusetts Clean Waters Act (M.G.L.c.2l,s.26-53) was amended by Chapter 246 of the Acts of 1973 to authorize the Massachusetts Department of Environmental Quality Engineering (DEQE), Division of water Pollution Control, Boston, Massachusetts, to regulate discharges into all waters of the Commonwealth of Massachusetts, including groundwaters. The DEQE regulates discharges through the issuance of discharge permits which impose limitations on the amount of pollutants which may be discharged in the effluent, together with monitoring and reporting requirements and other conditions to insure adequate treatment of all liquid wastes prior to discharge. The DEQE reviewed the application submitted on behalf of Jiminy Peak, Inc. for a permit to discharge sanitary wastes from the Jiminy Peak secondary wastewater treatment system located off Brodie Mountain Road, Hancock, Massachusetts, and subsequently developed the conditions contained in the Groundwater Discharge Permit No. Ø-188. More specifically, Jiminy Peak, Inc. (i.e. the permittee) has been authorized to discharge into the ground from the Jimmy Peak secondary wastewater treatment facilities for which the Permit No. Ø-188 was issued, a treated effluent

Jan 1, 1989

The Mining Foundation of the Southwest will hold its 14th annual American Mining Hall of Fame awards banquet Saturday, Dec. 7, 1996 at the Leows Ventana Canyon Resort in Tucson, AZ. Each year, preceding the Arizona Conference of SME, the Mining Foundation sponsors this banquet to honor outstanding contributions by people in the mining industry. A permanent display of honoree vitae is located at the Arizona Historical Society in Tucson. Each year, one living award recipient and up to two honorees from mining’s history are chosen by the hall of fame committee and the board of governors of the Mining Foundation. In 1989, the foundation also established a medal of merit to recognize outstanding individual technical and professional contributions to the mining industry. And, in 1995, an award was created to recognize contributions made by companies and individuals in partnership with the mining industry. This year’s inductee is Richard de J. Osborne, chairman, president and chief executive officer of Asarco. He will also be the featured speaker at the banquet.

Jan 1, 1996

By R. L. Miller

"Miners worldwide use a tremendous amount of energy in producing finished minerals for the end user market. In accomplishing this goal, they incur energy costs that can range from 20% to 30% of the total cost of production, so there is fertile ground for cost savings. To unlock this huge value in cost reduction, energy analysis is the key and is broken into several segments: 1. Fuel analysis for power generation 2. Energy supply & demand 3. Opportunity cost for lack of power 4. Backup power 5. Power contracts 6. Energy efficiency 7. Renewable energy 8. Continuous energy management FUEL ANALYSIS FOR POWER GENERATION What is the first thing we evaluate when looking at power supply alternatives for the mining industry’s large power requirements? Is it 1) site, 2) engineering, procurement, and construction companies, 3) independent power producers, 4) turbine vendors, 5) grid connections, or 6) fuel supply, logistics, and infrastructure? In evaluations of power supply alternatives for mining companies with special emphasis in developing countries, there is one over-riding conclusion: reliable fuel supply drives the energy generation economic engine. Evaluating several different fuels including liquefied natural gas (LNG), natural gas, diesel, heavy fuel oil, and liquefied petroleum gases (LPG) among others, the best project outcomes are those where fuel supply, pricing, logistics, and infrastructure are given an extensive amount of time during the analysis stage. In an assessment of the twenty-year costs of generating power from multiple fuels, each fuel’s costs were placed into three separate net present value (NPV) buckets of: 1) capital, 2) operating and maintenance, and 3) fuel. Within a range of 65% to 85% for all fuels, fuel cost was the largest component of the NPV of the life cycle power generation costs. So if 65% to 85% of your life cycle power generation cost is one item, shouldn’t miners spend a corresponding amount of time in the analysis stage fully understanding this key determinant for a successful power project? In developing countries where power generation infrastructure may not exist or does not exist at the same level as is found in North America and Europe, fuel analysis becomes even more important. One of the key questions for fuel importation in developing countries is the draft at existing ports to allow larger vessels to dock at the jetty. Can larger ocean-going tankers dock at the port for off-loading, or is the port’s draft too shallow, thus forcing a Single Point Mooring (SPM) system or Conventional Buoy Mooring (CBM) system to be constructed at substantial capital expense? Once fuel can be imported, sufficient onshore storage capacity should exist, or must be built to off-load the entire fuel cargo from the larger ships. Additionally, the throughput capacity of the pipeline from SPM/CBM must allow a rapid unloading of the fuel from ship to shore to eliminate steep demurrage costs for the project."

Jan 1, 2017

By Dan Witkowsky

In an increasingly environmentally conscious world, mining&apos;s importance to society has often been misunderstood and even maligned by the public. Extreme and impractical ideas have often been presented to children because of the lack of accurate, timely resource materials available to educators. In the late 1960s. two mining engineers, S.P. "Pi" Warren and C.L. "Lindy" Barker, became aware of this situation. They proposed to develop a summer field course to provide a factual overview of the minerals industry for teachers. The pair believed that teachers could become better informed to educate students, and future generations, about mining. These two Colorado Mining Association (CMA) members felt that such a course could reduce much of the misunderstanding about this vital industry. This could be done by providing a balanced perspective of mining, not only for kindergarten-through-grade-12 teachers, but also for the students they would be teaching during their careers. Students who better understood the minerals industry could better formulate an unbiased view of it. The course would seek recognized authorities from industry, academia and government who would lecture in their respective fields of expertise. The course would provide a total concept of the coal, aggregate, metals and industrial minerals industries. It would include geology, geophysics, exploration, mining, processing, marketing, product applications, economic, mining history, careers, and environmental responsiblity. When possible, site visits would permit educators to view operations and to meet the men and women who are industry leaders. Teachers would pay a small tuition fee. The balance of the program expenses for each teacher would be paid through scholarships provided by industry and individuals. The "total concept" idea obtained the support of the minerals industry. The support of CMA&apos;s Education Committee and the Colorado School of Mines (CSM) was obtained in 1968. Colorado&apos;s Commission on Higher Education approved teacher recertification credits through CSM&apos;s Office of Special Progams and Continuing Education for those successfully completing the program. The first six-week series of classes presenting the total concept of the indus¬try was held at CSM in 1969. In 1977, the CMA Education Foundation Inc. (CMAEF) was established as a Colorado nonprofit corporation. The "Total Concept of the Mining Industry" (Total Concept) course was placed under its sponsorship. CMAEF is dedicated toward this continuing education program (Table 1). In 1994, the course was streamlined to four-weeks for six hours recertification credit.

Jan 1, 1997