Search Documents

By T. Harrison

Surface coal mines in West Virginia are receiving stringent NPDES discharge limits for total recoverable selenium. With limits in the low parts-per-billion range, selection and implementation of proper sample collection and analytical methods are imperative for quality assurance and control and for consistency in results. Given the typical oxidized form of selenium in the water, the low limits and the large and variable flow rates from the watersheds, end-of-pipe treatment is difficult and cost-prohibitive to implement. Discharge locations in the remote and steep terrain exacerbate the problem. To evaluate options for end-of-pipe treatment at a Patriot Coal Corporation surface mining operation in West Virginia, CH2M HILL performed wastewater characterization for a range of key constituents and selenium species at three outfalls for selection and preliminary sizing of appropriate treatment processes. A preliminary evaluation of base and wet-weather flows was done to understand flow variability considerations for discharges. A conceptual evaluation of technologies to treat selenium to permitted levels was conducted in con-junction with order-of-magnitude life-cycle cost estimates.

Jan 1, 2010

By Evan J. Owen, Virginia T. McLemore

of high specific gravity, resistant minerals that form from mechanical concentration by waves, currents, and winds in marginal-marine environments. These sediments are enriched in critical minerals such as titanium, zirconium, and REE. Cretaceous beach-placer sandstones are found in the Colorado Plateau of northwestern New Mexico. Originally discovered by airborne radiometric surveys for uranium in the 1950s, these beach-placer sandstones are being re-examined with modern methods as potential sources for critical minerals. Selected beach-placer sandstones have been sampled, mapped with ground radiometric surveys, and analyzed with whole-rock and trace element geochemical methods. Mineralogy is being determined with optical methods, XRD, and EMPA. Zircon, rutile, ilmenite, and monazite are the primary heavy minerals of interest found in the studied deposits. Initial results show that the sandstones contain up to 1.4% total REE, 29.4% TiO2, and an estimated 4.9% ZrO2. Chondrite-normalized REE diagrams show distinct light REE and minor heavy REE enrichment, as well as pronounced negative Eu anomalies for each deposit.

Feb 1, 2024

By Seth Pollak, Jon Hurt, Mark Havekost, David Vardiman, James Schick

"INTRODUCTION The Long Baseline Neutrino Facility (LBNF) Far Site Conventional Facilities are proposed to be sited at the Sanford Underground Research Facility (SURF) located within the former Homestake Gold Mine in Lead, South Dakota. The project involves excavation and support of three large caverns which will house four 10 kT fiducial volume liquid argon (LAr) neutrino detectors and cryogenic equipment, as well as numerous ancillary connecting drifts and chambers. This paper describes the geological setting of the project, the geotechnical investigation undertaken nearly a mile underground and the challenges associated with collection of reliable data in a high stress and geologically complex environment. The layout for the new facility will be presented, along with a description of some of the constraints that will impact construction, including shaft access and working within an operating research facility. THE LBNF PROJECT The global neutrino physics community is coming together to develop a leading-edge, dual-site experiment for neutrino science and proton decay studies, the Deep Underground Neutrino Experiment (DUNE). The facility required for this experiment, the Long-Baseline Neutrino Facility (LBNF), will be an internationally designed, coordinated and funded program, comprising the world's highest-intensity neutrino beam at the Fermi National Accelerator Laboratory (Fermilab) in Batavia, IL and the infrastructure necessary to support massive deep underground cryogenic detectors 800 miles (1,300 km) downstream at the LBNF Far Site at the Sanford Underground Research Facility (SURF), in Lead, South Dakota. The Deep Underground Neutrino Experiment is expected to achieve transformative discoveries, making definitive determinations of neutrino properties, the dynamics of the supernovae that produced the heavy elements necessary for life, and the possibility of proton decay. Neutrinos created by the LBNF beamline will travel on the 1,300 km (800 mi) path shown in Figure 1 leading straight through the earth's crust to intercept DUNE's massive, cutting-edge neutrino detector at the Sanford Lab. No tunnel is needed as neutrinos pass easily through soil and rock rarely interacting with the matter. The DUNE far detector will consist of four modules, each of which will be housed in a cryostat containing 17,000 metric tons of liquid argon target material, providing a 10kT fiducial volume. The LBNF Far Site Conventional Facilities project will excavate and fit out a set of four caverns 4850 ft underground in which to place them."

Jan 1, 2016

By C. Opoku-Ware, M. Kukay, P. Conrad, F. Inkoom, R. Pal

Researchers at Montana Tech are investigating the potential for developing trees tolerable to degraded un-reclaimed mine site tailings and soils as a solution to re-establishing long-term tree growth on those sites. This project involves growing tree seedlings from seeds planted in the degraded mine tailings and soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in degraded tailings and soils in Butte, Montana with minimal post-planting human intervention. Work conducted on the project to date has shown successful growth of seedlings in degraded tailings and soils. INTRODUCTION In an effort to improve Butte Area One natural resources, this research project is working to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU) (Opoku-Ware, et al 2018). Research by Blicker, et al (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic values (Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown to seedlings in a greenhouse located on Montana Tech’s campus which will be planted in degraded soils located within the BPSOU. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. The trees will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow. The project combines research with tree seedling growth to provide a resource for Butte that could produce thousands of tree seedlings each year adapted to the harsh climate, soil, and tailings conditions that exist in the BPSOU where they will grow. It is anticipated that the trees developed by the project will have the capability for long-term survival and growth because they will be germinated and grown into seedlings in the degraded soils and tailings collected from the BPSOU where they will be planted. Soils and tailings collected for the project have been evaluated to determine if they lack nutrients or contain substances potentially toxic to the long-term growth and survival of the trees. Toxic levels of metals, high concentrations of soluble salts, extremes in pH, nutrient deficiencies and imbalances, surface crusting, high bulk density, low infiltration rates, high surface temperatures, low cation exchange capacity, restricted microbial activity, low water retention, harsh climatic conditions and surface particle movement are some of the traits of mine tailings sites that restrict revegetation efforts (Barth, 1986).

Jan 1, 2019

By L. A. Khan

This paper first discusses the physicochemical cleaning methods used to process fines followed by an analysis of the subprocesses of froth flotation and the adverse effects of slimes and particle oxidation. These subprocesses include the phenomena of interception, contact, adhesion and levitation. Preventive and corrective measures to combat the generation of fines and their effects are suggested. Preventive measures include controlled grinding, limited liberation, flotation at coarser sizes. Means of preventing oxidation and/or removing oxidation products are a1 so discussed. Corrective measure to increase recovery include intensive aeration, aggregation of particles, intensive mixing, increased retention time, and reduction of detachment. Measures leading to improves selectivity involve means to reduce slime coating, achieve selective mineralization of bubbles and minimize entrapment.

Jan 1, 1986

By James A. Finch, Xiang Zhou, Yue Hua Tan

Methods to determine frother functions, control of bubble size and froth properties, are now widely used. Some collectors also exhibit frother functions which are less understood. Using a water-air system in a mini-mechanical flotation cell setup, this paper determines bubble size and water overflow rate for three amine collectors: one primary amine (dodecylamine, DDA) and two commercial ether amines (Flotigam® EDA and Flotigam® 2835-2L) and their combination with two common frothers, MIBC (methyl isobutyl carbinol) and PPG 425 (polypropylene glycol, molecule weight 425). Compared to the frothers, the amines were less effective in reducing bubble size, giving larger minimum size and the two commercial amines showed evidence of coalescence at low concentration. In blends, at fixed frother dosage, frother eliminated the coalescence but as amine concentration increased the amines dominated bubble size. Water overflow was a strong function of reagent type. For fixed 1-cm froth depth, PPG 425, Flotigam® 2835-2L and to a lesser extent DDA produced overflow while MIBC and Flotigam® EDA did not. In blends with frother overflow increased except with Flotigam® EDA. Mechanisms are briefly explored. The principal benefit of blending identified is the elimination of coalescence if residual concentration of the two commercial amines is below ca. 10 ppm.

By S. P. Fleming

An acid mine drainage sludge containing 0.26% nickel, 0.21 % cobalt and 4.5% manganese was leached in a one-liter reactor with sulfuric acid in the absence and presence of sodium sulfite. The effects of temperature (25°C and 52°C) and sodium sulfite concentration (up to 0.03 molar) on the leaching rate were particularly investigated. The leaching rates of nickel and cobalt with sulfuric acid have been determined to be controlled by diffusion through product layer. It has been found that effective leaching conditions to give more than 90% extraction of nickel, cobalt and manganese while keeping the iron extraction below 10% come with an elevated temperature and a low sodium sulfite concentration at pH 3; for example, 52°C and 0.01 molar sodium sulfite.

Jan 1, 1992

By B. A. Ashley

Rosebud Mining Co. (RMC) is based in Kittanning, PA. As of October 2013, it operated 24 active underground mines in Pennsylvania and Ohio. RMC?s Tracy Lynne Mine is located approximately 5 km (3 miles) east of Apollo, PA, (approximately 48 km or 30 miles northeast of Pittsburgh, PA) and mines the Lower Kittanning coal seam. The coal seam averages approximately 1.1 m (45 in.) thick and is of steam coal market quality. The mine is a single unit operation. Coal is mined using a continuous mining machine and is transported from the face to the conveyor belt using a continuous haulage system. Typical ventilation in the mine consists of an exhausting fan that draws air through isolated intake, belt and return air courses (Fig. 1).

By P. Eger

Minnesota contains a major low- grade copper-nickel sulfide resource within the Duluth Gabbro Complex. Several companies have actively explored this resource. Open pit mining would be required to develop portions of the resource, and as a result, large quantities of sulfide-bearing lean ore and waste rock would be stockpiled. Although the problems associated with high-sulfide tailings and acid mine drainage are well documented, the leaching characteristics of low-grade mineralized stockpiles must be understood for environmental impact assessment, siting, and planning. The Minnesota Department of Natural Resources and AMAX have cooperated in a research program to study leaching and revegetation -of test stock- piles, Six small (1600 'tons) stockpiles were constructed at the MINNAMAX Project Site and they range in composition from 0.29 to 043 g % copper, 0.075 to 0.09% nickel, and 0.6 to 1.45% sulfur. Two of the stockpiles were covered with mineral soil, one was covered with topsoil, and three were not treated Revegetation plots were established on the piles which received a soil cover. Leachate samples and flow measurements were collected at the base of the piles. Initial results indicate that metal concentrations in leachate samples range from 10 to 10,000 times the concentrations found in the streams of the area. During the first growing season, the test pile covered with topsoil yielded 30% less water than untreated test piles. No reduction in yield was observed for the piles that were covered with the less fertile mineral soil. First-year vegetative growth, expressed as biomass, was four times greater on the-topsoil pile than on the mineral soil piles. The long-term effects of vegetation on leachate quantity and quality continue to be investigated.

Jan 1, 1980

By J. L. Fuller

Mine ventilation surveys were conducted by Technical Support engineers during June 1987 and September 1989 at the Dutch Creek Hine. The mine is located near Redstone, Colorado and is operated by Mid-Continent Resources, Inc. Following completion of the initial survey, several recommended improvements were incorporated into the ventilation system by mine personnel. The second survey permitted documentation of the effects of those changes on the ventilation system performance. This paper describes the processes involved in the implementation of the recommended changes. The substantial improvements in system efficiency and reduced operating costs are also described.

Jan 1, 1991

By M. A. Reyes, J. Bickson, J. R. Srednicki

Federal laws mandate the presence of refuge alternatives (RAs) in underground coal mines and provide guidelines for harmful gas removal. After an explosion, harmful gases can follow survivors into an RA and can reach a deadly concentration. Investigators from the National Institute for Occupational Safety and Health (NIOSH) tested 12 ventilation system configurations (VSCs) to purge sulfur hexafluoride (SF6) tracer gas from a built-in-place (BIP) RA in the Experimental Mine in Bruceton, PA. Using a borehole air supply, tests were conducted with airflows of 750 and 1,000 standard cubic feet per minute (SCFM). Excluding a VSC where the air inlet was 1.98 m (78 in) from the air outlet, the results show that the time to purge the SF6 concentration from 1,000 parts per million (ppm) to 25 ppm ranged from 26 to 29 minutes for an airflow of 750 SCFM and ranged from 18 to 23 minutes for an airflow 1,000 SCFM. Mines can use this information to reduce purge time in case of a mine disaster and determine which VSC to avoid. INTRODUCTION After a fire or an explosion in an underground mine, the concentration of carbon monoxide can reach a fatal level. In a mine disaster, the main goal is to escape. However, if miners cannot escape, they have to migrate to a location to find refuge and, if possible, communication, and a borehole source for a fresh air supply. To ensure survival of the miners, Federal laws mandate the presence of a refuge alternative (RA) within 304.5 m (1,000 ft) of the nearest mining face. In addition, Code of Federal Regulations Title 30 CFR Section 7 sets the guidelines for personnel tracking, RAs, and the removal of noxious gases in underground coal mines (Mineral Resources, 30 CFR, 2014). Federal regulations define an RA as a protected, secure space with an isolated atmosphere and integrated components (Mineral Resources, 30 CFR, 2014). There are three types of RAs: portable metal RAs, portable tent-type RAs, and built-in-place (BIP) RAs. A BIP RA is constructed using masonry or other stoppings to create an isolated space in a mined-out area. Blast doors are installed in one or both of the stoppings for the miners to enter the RA. Furthermore, RAs must provide the following components: breathable air, food, water, air monitoring, and harmful gas removal. Federal regulations have emphasized the mandate for breathable air and harmful gas removal in the following words: “Purging or other effective procedures shall be provided for the airlock to dilute the carbon monoxide concentration to 25 ppm” (Mineral Resources, 30 CFR, 2014). The purpose of the mine ventilation system is to provide a sufficient quantity of air to the underground mine workings, to dilute methane and other contaminants, to maintain a suitable working environment, and to prevent accidents from happening (Cheng and Wei, 2014). In addition, the organic nature of coal amplifies risks from poisonous gases, explosions, and fires (Engström et al., 2018). If an underground coal mine ventilation system fails after an explosion, the concentration of toxic gases, most notably carbon monoxide, will increase. Carbon monoxide is dangerous because it creates tissue hypoxia by binding to hemoglobin (Özmen and Aksoy, 2015).

Jan 1, 2019

By R. W. Wittkopp

The Relief Canyon gold deposit is located approximately twenty- four kilometers east of the town of Lovelock in Northwestern Nevada. At Relief Canyon, the Late Triassic Grass Valley Formation has been thrust over the Late Triassic Natchez Pass Formation. The lower plate Natchez Pass Formation is composed of massive gray dolomitic limestone which is locally silty and sandy. The upper plate Grass Valley Formation is composed of shale, siltstone, argillite and quartzite. Gold mineralization at Relief Canyon occurs along the highly brecciated thrust contact between these two formations. Weak gold mineralization often occurs above the thrust in the Grass Valley Formation, however, most of the ore grade mineralization is present below the thrust in the brecciated Natchez Pass Formation or where the two formations are mixed as a result of movement along the thrust. Several types of gold mineralization have been recognized at Relief Canyon. A large amount of the ore is present as a jasperoid breccia, however, significant amounts of ore occur as a mixed breccia composed of upper plate rock, fresh limestone, clay and jasperoid breccia. Gold ore also occurs in a fresh limestone breccia which contains a large amount of clay. Below masses of jasperoid, jasperoid stringers containing gold extend into the fresh limestone. Gold mineralization at Relief Canyon appears to be truly disseminated and has the typically associated trace elements of arsenic, antimony, mercury and fluorine. The Relief Canyon deposit can be classified as a structurally controlled disseminated gold deposit. Other deposits that fit this classification are the Pinson and Dee gold mines.

Jan 1, 1984

By D. C. Torre

Ever since the early '60's there have been efforts to develop and produce reliable continuous haulage systems capable of taking the full output of a continuous miner and transporting it, in one continuous flow, from the face to the tipple. The majority of the continuous haulage systems which have been most successful to date were placed in operation in the early '70's and were all of the bridge conveyor type, usually consisting of bridges and mobile bridge carriers attached at the inby end to the continuous miner and at the outby end to the panel conveyor itself. These successful bridge conveyor type continuous haulage systems were, and continue to be, either of the belted or chain type. Undoubtedly, the most successful belt type continuous haulage systems are those manufactured and marketed by the Long-Airdox Company. Until early 1977, the most successful chain conveyor type haulage systems were manufactured and marketed by Jeffrey Mining Machinery Division. In 1977, Long-Airdox reentered the market with a chain type system to complement its belted system. I say "reentered" because the original bridge type continuous haulage system was introduced to the coal mining industry in the early '60's by the old Long Company, a predecessor of the current Long-Airdox Company, and those original units were of the chain conveyor type.

Jan 1, 1981

By John T. McDonough

The Climax Mine of AMAX's Climax Molybdenum Division is currently producing approximately 34,000 tons of molybdenum ore per day from two underground levels (see Figure I), and initial design is underway for the next deeper (1200) level. The aim of this report is to present the methods of site evaluation used at Climax for cavability determinations and underground support design. Climax succeeds with its panel caving system of mining (Julin, 1973) (Figure 2) largely because of the presence of pervasive geologic structural discontinuities. The stockwork ore body at Climax was formed by the multiple intrusion of mid-Tertiary rhyolitic magmas into Precambrian granite, schist and gneiss, and the hydrothermal emplacement of molybdenite into the network of fractures that were generated during the forceful upward intrusion of magma. Subsequently, intrusive events that were more deeply seated refractured the overlying, ore- bearing stock and propagated a complex system of axial and radial fractures. Post-ore movement along the Mosquito Fault (Wallace, 1968) and its associated stranded shear zones further fractured the ore body and disordered the existent geologic structure. The result of these structural events is a brittle, crystalline ore body that is transected by a complex pattern of faults, shear zones, and joints that augment cave initiation and enhance comminution of the ore blocks. Generalizations can be made about the structural trends within the ore deposit (King, 1946; Kendorski, 1973), however, the intensity and orientation of geologic structure is by no means uniform throughout the ore body. The relative intensities of silicic and argillic alteration are also highly variable (Vanderwilt and King, 1955). As a consequence, no single rock-mass model suffices as a standard for mine design, and site characterization for cavability and support design is a continuous process.

Jan 1, 1977

By C. F. Johnson

Nearly all of the sulphur produced in the world today is converted to sulphuric acid and 49 % is used in the manufacture of fertilizers. In the last few years we have seen the beginning of another chapter in the volatile history of sulphur as the severe shortage of 1963:-67 has been transformed into present-day surplus. Prospects for further aggravation of this situation in the years ahead seem assured. In 1970, western world production showed a rate of increase of 4 -5%, which 1S somewhat less than that of 8% for the period 1963-1967. The rate of growth of consumption dropped considerably in 1968 when the demands of the fertilizer industry fell. During the same period of time, wide-spread demands have been set in motion for a clean environment which indicates that a fundamental change in sulphur supply, demand, and even sources, is likely to result from this upheaval. The sale of sulphur by Poland to the western world has increased and for 1970 was estimated at over one million metric tons. In the next few years, increase in Canadian sulphur supply will stern from two sources;

Jan 1, 1972

By E. Watkins, S. J. Schatzel, V. Gangrade, K. M. Ajayi, Z. Khademian

Longwall-induced deformations could jeopardize the mechanical integrity of shale gas well casings positioned in the abutment pillar of a longwall mine. The in situ and induced fracture networks surrounding the gas well could provide pathways for gas flow into the mine creating safety concerns. Hence, this study by the National Institute for Occupational Safety and Health (NIOSH) develops a discrete fracture network (DFN) model to characterize the fractures in the overburden based on geomechanical analyses of mining-induced fracture apertures at a study site in southwestern Pennsylvania. The apertures from the geomechanical model are used to develop a stochastic DFN model of the site in fracture flow code (FFC). Multiple realizations of the stochastic DFN model that replicate potential fracture geometries are simulated, and the fracture permeability is compared with field measurements. A maximum field measurement of 5.03 × 10− 12 m2 (5080 mD) and 3.82 × 10− 13 m2 (386 mD) was estimated over the abutment pillar at the Sewickley and Uniontown horizon, respectively. The results show that the average permeabilities from the DFN model agree closely with the field measurements. In addition, the comparison of all the field measurements and 100 DFN realizations show the model is representative of field conditions. These findings provide critical information regarding fracture characteristics in the overburden, which will further be used to predict potential shale gas flow to the mine in the event of a casing breach for an unconventional gas well.

Jun 17, 2022

By Roland Arnold, Richard Gradnik, Martin Zeindl

This paper presents the details of the Kramer tunnel project in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of GarmischPartenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million (incl. VAT), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for single-tube tunnels is solved by a parallel escape tunnel passable for vehicles. All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). In order to reduce the geological risk for the owner, the escape tunnel was supposed to be completed before the design process for the main tunnel ever began. The exploratory tunnel was awarded to a competitor with an separate contract.

Jun 13, 2021

By Robert B. Scott

Acid mine drainage, discharging from coal beds, has polluted our streams and rivers since early time. These pollutants affect water quality by lowering the pH, reducing natural alkalinity, increasing total hardness, and adding undesirable amounts of iron, manganese, aluminum and sulfates, The tangible damages are the costs involved in replacing equipment corroded by the acid water, additional treatment costs at municipal and industrial water treatment plants, and damages resulting from corrosion of steel culverts, bridge piers, locks, boat hulls, steel barges, pumps, and condensers. Intangible damages, which are real and important, include destruction of biological life of the stream, reduced property values, and streams rendered undesirable for recreational uses.1 The major problems of mine drainage occur in the anthracite and bituminous coal regions in Appalachia. However, many of the western mining states have significant mine drainage problems in specific areas, but the overall problem is not as great as in the eastern states.

Jan 1, 1970

By Joaquin Ruiz

Naica consists of at least 10 mantos and 40 chimneys that have produced over 15 million tens of ore with 10% Zn, 13% Pb and 13 oz/ton Ag. The ore occurs in thick-bedded, folded Cretaceous limestone. Fractures and 26 Ma old felsite dikes with an initial strontium isotopic ratio of 0.708 localize the mineralization. The mantos follow the dikes and have abundant early skarn with manganohedenbergite, calcic garnet, idocrase, quartz, calcite, wollastonite, schellite and later sulfides. The chimneys arise from the mantos and change from silicate-rich to silicate-free sulfide limestone replacements. Carbon, oxygen and sulfur isotope data on carbonates, silicates, sulfides and sulfates are compatible with a single evolving (magmatic?) fluid.

Jan 1, 1985

By Rajat Gangrade, Haotian Zheng, Jarrett Smith, Daniele Nebbia, Mike Mooney

The application of artificial intelligence (AI) to improve tunnel boring machine (TBM) operations requires a significant amount of information to train robust performance prediction models, e.g., for tunneling-induced settlement, productivity, tool wear, etc. This paper presents the AI framework applied to the North-East Boundary Tunnel (NEBT), the largest component of the Clean Rivers Project in Washington, DC. The paper focuses on required elements for real-time AI use to estimate tunneling-induced ground and building deformation and cutter tool wear. Keys to the framework include defining the necessary quantities of data required as well as the process of windowed training, validation and model testing. To date, the models developed for ground deformation and tool wear show satisfactory performance when compared to observed field observations during tunneling.

Jun 13, 2021