Search Documents

By P. E. Sperry, R. E. Heuer

The United States Bureau of Reclamation is constructing the $200 million Navajo Indian Irrigation Project to irrigate 110,000 acres of land on the Navajo Indian Reservation in northwestern New Mexico. Water from the San Juan River is impounded by Navajo Dam and will be conducted for 26 miles along a series of tunnels and canals to the area to be irrigated. Tunnel No. 3 is the third in a series of six tunnels along the route. Bids for construction of Tunnel No. 3 were received by the Bureau of Reclamation in September, 1970. Fluor Utah was low bidder at $8.7 million. Ten of the 12 bids were based on excavation by tunnel boring machine. The consulting firm of A. A. Mathews, Inc., was retained by the contractor to advise on geologic and rock mechanics conditions after support problems developed in the tunnel. Tunnel No. 3 is 15,264 feet long, has an 18 foot lined diameter, rises approximately one-half inch per 100 feet in the direction being excavated, and is 6,000 feet above sea level. There is one short curve in the alignment. Minimum concrete thickness is 12 inches with eight inches from 'A' to 'B' line making a pay diameter of 21 feet, 4 inches. The tunnel is supported with rock bolts and steel pans. Mole excavation began on May 13, 1971 from a blasted starting chamber. After 46 feet were excavated the mole was shut down and the trailing muck handling equipment was pulled into place. After advancing 1,700 feet in 34 days, unanticipated ground water conditions and ground support problems were encountered slowing moling so that the next 1,000 feet of advance consumed 97 days until December

Jan 1, 1997

By Earle Faig

Earle Faig Along with other transportation modes, the barge industry will be greatly affected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events has caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of its long experience in moving large quantities of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to that industry. Barge companies operate on a river system that is over 40 Mm (25,000 miles) long. It includes the East and West Coasts and the Mississippi River System comprised by the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior-Tombigbee, and Mobile Rivers, and some smaller tributaries. The Gulf Intracoastal Waterway stretching along the Gulf Coast from Brownsville, TX, to Apalachicola, FL, also is considered part of the inland waterway system. Approximately 1,800 companies operate on the inland river system and have a combined fleet of about 4,400 towboats and 28,000 barges. The fleet of towboats represents 4.8 GW (6.4 million hp) of power. The towboats comprising this fleet vary in size from a small harbor boat to a large line haul boat with 7.5 MW (10,000 hp) of power. The choice of size and power of the boat depends on a number of factors, including the size of the river and operational constraints, such as lock size, river-current rate, and water level. The choice also depends on the tow size. A single tow on a river capable of locking through 15 barges at a time handles up to almost 20 kt (22,000 st), whereas a tow on the lower Mississippi, which has no locks, can accommodate up to 41 kt (45,000 st) of cargo. Because the quality of coal is not typically damaged by exposure to the elements, it is usually moved in open hopper barges, although covered barges are used occasionally. The most frequently used size is the jumbo barge that measures 59 m (195 ft) long by 11 m (35 ft) wide by 4 m (12 ft) deep and can handle up to 1.4 kt (1,500 st) of coal. Advantages of Barge Transportation Barging offers several inherent advantages in transportation of bulk commodities like coal. First, barges can carry large quantities of product. A single jumbo hopper barge can handle 1.4 kt (1,500 st) of cargo while it takes 15 91-t (100-st) capacity rail cars or 57 trucks hauling 24 t (26 st) each to move an equivalent amount of cargo. Thus, barges can move more tonnage with less equipment than competing forms of transportation. Second, barging offers the most fuel efficient means of transportation. Less energy is required to push a load over water than to pull a similar load over land. The amount of pollution attributable to barge traffic is minimal because barges consume less fuel. Third, barging is an inexpensive form of transportation. The inland waterway industry transports about 12% of the nation's freight for about 2% of the total freight bill. This can be attributed to competition between the large number of companies on the river system and competition with other transportation modes. Fourth, barging is an environmentally safe method of transportation. Inland river routes expose fewer urban areas to hazardous substances than rail or truck. And barge spills occur less frequently than rail or truck spills. The industry does pose some disadvantages. The waterway system is constrained by the natural river network, so barges cannot travel on the most direct straight-line route. This means that barging is usually an incomplete form of transportation requiring interface with truck or rail. The industry's market is limited to those geographical areas that are located on or near the rivers. In addition, it is a time-consuming transportation mode, making it impractical for many types of commodities.

Jan 10, 1982

By C. E. Jordan

The Tuscaloosa Metallurgy Research Center of the Bureau of Mines, U.S. Department of the Interior, is investigating the recovery of phosphate from beneficiation slime, as part of the Bureau's efforts to conserve mineral resources through increased use of wastes. Phosphate equivalent to about two-fifths of U.S. production is discarded annually in the wastes. Exploratory flotation tests on the plus 5-um fraction of a slime sample showed promise for a classification-flotation technique. Onsite classification tests at six phosphate washing plants were conducted with a two-stage hydro cyclone system designed to recover the plus 5-um material. The cyclone underflows contained 8.3 to 19.1 percent P2O5, and the recovery of the plus 5-um PZOS values ranged from 81 to 95 percent. The percent P2O5 recovery from the total slimes ranged from 38 to 47 percent. Batch-flotation studies are currently being conducted.

Jan 1, 1978

By Alper Kirmaci, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Injuries and fatalities resulting from roof falls are still a major concern in U.S. coal mines, and many researchers are focused on developing meaningful approaches to minimize this hazard. In the United States, coal mine roofs can vary widely in composition, geometry, and inherent heterogeneity, leading to a wide array of different roof fall failure types. Researchers frequently employ numerical modeling tools to reproduce this physical phenomenon and provide key guides to engineers regarding roof conditions and control as long as the input data and constitutive relations are appropriately selected. Simulating such complexity requires expertise and constitutive models that adequately simulate roof behaviors. However, the currently available constitutive models have shortcomings in capturing some of the roof fall failure types common in underground coal mines, such as guttering. A new constitutive model is developed to address the shortcomings of constitutive models commonly used for coal roof stability analysis. The constitutive model developed in this study combines the anisotropic-elasticity and nonlinear strain-softening responses. In addition, the developed constitutive model can simulate up to three different joint sets implicitly, allowing for use in both continuum and discontinuum settings, and can be used in both Lagrangian finite-volume and distinct element method codes of Itasca. First, the mathematical expressions of the model are provided. Afterward, the validation phase of the developed model that covers comparisons with analytical solutions and those of existing models (e.g., anisotropic elasticity, ubiquitous-joint, and bilinear strain-hardening/softening ubiquitous-joint plasticity) is presented. Finally, a hypothetical coal mine roadway facing high horizontal stress is simulated. The presented model successfully shows three distinct stages of a cutter roof in a shale roof: (1) initiation of shear cracks at the rib– roof intersection, (2) extension of cracks deeper into the roof (i.e., above the roof bolt length horizon), and (3) cantilevered roof. It is demonstrated that the presented constitutive model has the potential to help future researchers in simulating various roof responses.

Jul 1, 2023

By Ross Goodman, Jesse Salai

The Ohio River Tunnel Project encountered multiple unexpected geotechnical challenges such as crown and invert instability due to the overstress condition affecting the strata above, below, and in the tunnel alignment during and after TBM excavation along with the potential for methane inflow. This paper showcases how the orientation of a tunnel alignment has a significant impact on how in-situ geological stress can impact the excavation of a tunnel from the contractor’s point of view and how geological features influence gas inflow to the alignment over time.

Jun 13, 2021

By J. L. Coburn

The Huari-Huari ore body is located in Southern Bolivia, at an elevation of approximately 3,800 meters above sea level. The ore is a complex massive sulfide, slightly marmatitic sphalerite, in a fault fissure filled hypo- thermal vein in Paleozoic shales and quartzite-altered sandstone. The sphalerite has common associations with pyrite and quartz and is frequently intricately intergrown with stannite, chalcopyrite, and pyrrhotite. The sphalerite also contains numerous inclusions of pyrite, marcasite, galena, boulangerite, jamesonite, quartz, arsenopyrite, and cassiterite. A research program was undertaken to develop a flowsheet for the recovery of separate silver, zinc, and tin concentrates by selective flotation. Based on this experimental work and subsequent flowsheet development, engineering and construction of a 500 metric ton per day concentrator was undertaken. This paper describes the process that was developed for the Huari-Huari ore and the unique aspects of the Huari-Huari concentrator.

Jan 1, 1977

By R. Pazhianur

Cathodic Protection using impressed current was employed to reduce the wear of the mill wall during ball mill grinding. Wear rates were determined from weight-loss measurements made on four, I-inch diameter, mild steel coupons installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH values of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 40-60010. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It is also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1996

By R. P. Aldis

A wide range of mineral-derived products are required by the electronics industry for it to function. In one form or another, almost all the known elements have been experimented with and tested for various electrical applications. The two major areas for which minerals are used in electronics are as conductors and semiconductors. Conductors provide the means to transport and distribute electricity, while the main application of semiconductors has been to manipulate electricity. Silicon is the most widely recognized semiconductor material, but gallium, indium, and germanium are rated as the most important metals to the semiconductor industry for future and near future technologies.

Jan 1, 1991

Introduction Agrico Mining Co.'s Florida mining division has three surface mines and employs nearly 700 workers. The division produces some 6.3 Mt (7 million st) of phosphate rock annually. It is a good business. And Agrico has made it better by making it safer through a new approach to mine safety. In one year, Agrico - the second largest phosphate mining company in the US - recorded a stretch of one million manhours without an accident. That same year, the direct cost of accidents dropped to $9137 from a previous five-year average of about $50,000. Together with Don Roe, division manager of safety and security, Division General Manager Don Morrow made 1981 a watershed year for safety at Agrico. Morrow called on consultants from Safety Management Services of Du Pont's Specialty Services division to strengthen a safety program that was already better than average. From the late 1970s and into 1981, lost-workday cases (LWCs) were costing Agrico an estimated average of $22,000 each. And they were occurring with alarming frequency. In 1977, the company recorded six LWCs at an incidence rate of 0.64. This was followed by a jump to nine cases in 1978. In 1979, both occurrences and the rate increased - 10 LWCs at a 1.19 rate. The number of LWCs decreased to seven in 1980, with a rate of 0.71. Agrico instituted a far-reaching safety program in 1981, which began to take full effect in 1982. LWCs dropped from five in 1981, to three in 1982. And the direct cost plummeted from $110,346 to $28,828. In 1983, the mines recorded only one LWC. Its $9137 cost represented a reduction of $101,209 since the Safety Management Services of Du Pont had been called in. Through early 1984, the LWC incidence rate at the facility's three mines, phosphate drying plant, and transportation department was down to 0.26. This is 84% lower than the 1982 mining industry average, making it the safety leader among all Agrico companies, including its chemical plants. New Approach Agrico had the basics of a safety program in place when the Du Pont consultants arrived. But Du Pont suggested changes in responsibilities and company philosophy that formed the foundation of

Jan 1, 1985

By Keith Whitworth

The USSR, over the last 20 years, has continued to increase its out-put year by year and it is now almost four times what it was at the end of the Second World War. In 1975, it exceeded 700 million tons of run-oi-mine coal (all ranks) which amounts to over 20 percent of world output. This rapid progress has been due to modernization of the industry, by means of increased mechanization and automation and the development of new machines and systems for underground workings and by the expansion of open-pit workings and the development and implementation of larger earthmoving machines.

Jan 1, 1977

By Peter McKenna

Different reefs being extracted from a mine will, in all likelihood, have significantly different semi-variogram models - and these will probably vary from geozone to geozone. As errors of estimation are dependent on the semi- variogram parameters, it follows, if a mine samples all reefs in all sections using the same sampling grid pattern, that estimation errors (or limits of confidence) will not be the same throughout the mine. This may be an undesirable situation! A geostatistical study of the relative merits of alternative sampling arrangements has been carried out by considering different reefs in different sections of a South African gold mine.

Jan 1, 1989

By C. P. Boddy

One of the most difficult tasks a project manager will have in pre-mine planning is dealing with the mine site's hydrologic regime. Numerous federal statutes passed by Congress in the last decade have made the coal mining industry more responsive to the environmental impact during all phases of the mining process. Permitting these mines has dictated a cradle to grave approach in dealing with water related issues. This paper will attempt to explore the application of these technology- based laws and their direct application to the unique environment found in Alaska's interior regions.

Jan 1, 1985

By E. R. Bauer

A primary goal of Ground Control Research, Bureau of Mines, U.S. Department of the Interior, is to develop information that can be used by the mining industry to reduce accidents and fatalities due to failure of mine roof. A specific research objective is to determine methods to detect hazardous coal mine roof. This paper reviews the existing and experimental techniques, and describes a recent Bureau of Mines contract research project that resulted in a simple technique and prototype instrument for evaluating mine roof competence.

Jan 1, 1986

By J. Rostami, J. Brune, S. Slouka

Respirable dust poses long-term health issues to personnel working in mining and civil projects where mechanized mining and tunneling machines are used for hard rock excavation. Machines, such as longwall shearers, roadheaders, or continuous miners, use consumable picks to cut rock. However, rock dust is generated in the work environment each time the pick tip contacts the rock surface. Additionally, the generated dust can be reintroduced into the air further down in production, such as at transfer points. The purpose of this study is to characterize respirable dust particles generated at the pick tip at two stages of pick wear: new and moderately worn. Understanding dust characteristics in terms of concentration, size distribution, and particle shape throughout the life-cycle of the pick will provide a basis to mine and tunnel operators for changing out picks to mitigate dust generation at the source. This paper discusses the dust characteristics generated from preliminary full-scale cutting tests in a laboratory of an igneous rock block cut with conical picks at new and moderately worn levels of wear. The moderately worn pick generated a size distribution that favored smaller particle sizes compared to the new pick. The moderately worn pick also generated more overall dust, as the concentration level in mg/m3 was over double the amount of the new pick. Lastly, both picks generated particles that had similar aspect ratios and roundness measures.

May 18, 2022

By Bobby G. Cahoon

The ( ) Tayaaja ( ) . The deposit ( ) 130 kilometers due east of the continental divide and approximately 290 kilometers east-southeast of Lima (Figure 1). Relief in the immediate vicinity of the mine, which lies or the west side of the Mantaro river, is in excess of 2,000 meters, and the elevation varies from a low of 2,000 meters above sea level on the Mantaro River to a high of 4,386 meters at point T-27 (Figure 2). Although the Cobriza deposit was first reported by the Italian Geographer Antonio Raimondi in 1866, only three reports have been published on the deposit, which began production in 1966 (Duefias, 1908; Fernandez Concha and Garcia y Garcia, 1961; Petersen. 1965). Many private reports have, however, been written by geologists employed by the Cerro de Pasco Corporation. These reports and the author's observations, while employed as the Cobriza Division Mine Geologists form the basis of the present paper, which describes the relations between-the ore controls in the Cobriza mine and the regional and local structure.

Jan 1, 1971

By J. Brune, P. J. Coleman, L. Martini

Research in the field of mining safety and health in the United States plays an important part in protecting the lives of miners. The National Institute for Occupational Safety and Health (NIOSH) Mining Program conducts surveillance, studies and developmental work aimed at improving the safety and health of miners. With recent reviews of the Mining Program by the National Academy of Sciences and the Mining Program response (NIOSH, 2008), the importance of setting goals, conducting high quality engineering and scientific research and evaluating the outputs, outcomes, relevance and impacts of these projects has been reemphasized. Surveillance of reported injuries is a first step in deciding on research directions and in designing specific projects. Groups of injuries often share features and attributes that suggest common causes and may respond to similar preventive efforts. Identifying groups of injuries also serves to prioritize intervention efforts. The Mine Safety and Health Administration (MSHA) Accident and Injury database (MSHA, 2008) provides individual case reports of mining injuries, illnesses and certain no-injury accidents (events such as roof falls that stop mine production or miners’ activities for more than one hour). This database is an indispensable resource for researchers and stakeholders needing information on the statistics of these events. From an epidemiological perspective, research projects target groups of miners at risk due to specific patterns of work, equipment, mine settings and the management of safety and health in their mines. Incidence rates are provided by the MSHA data for selected variables, such as surface/underground location, standard industrial classification and state. While incidence rates are the preferred measure for all variables, denominators are not typically available; for example, to more clearly understand the data about injury by occupational type, it would be necessary to conduct demographic surveys. A current survey of the demographics of the mining industry should be complete by 2010, which will allow incidence rates to be developed for a number of variables such as age, occupation and experience. This survey will provide the first update of its kind since the first survey was conducted in 1985. This report describes an alternative method of analyzing and presenting MSHA data for the purpose of identifying high-cost, high-severity injuries and illnesses. Researchers at the NIOSH Spokane Research Laboratory (SRL) developed programs to find the top five most frequent accident classes, natures of injury, types of accidents and other selected variables from the MSHA database. Studying these variables gives a cross-sectional snapshot of the most frequent groups of injuries within a commodity, regional group or time period, and allows researchers to quickly understand developing patterns for new research projects. The primary benefit of this approach is to

Jan 1, 2009

By David J. Barr

Public Law 91-190 - January I, 1970 states that, "The purposes of this Act are: To declare a national policy which will encourage productive and enjoyable harmony between man and his environment; to promote efforts which will prevent or eliminate damage to the environment and biosphere and stimulate the health and welfare of man; to enrich the understanding of the ecological systems and natural resources important to the Nation; and to establish a Council on Environmental Duality." The administrative aspects of this National Environmental Policy Act of 1969 have in essence established the requirement that all agencies of the Federal government assess the consequence of their actions with an Environmental Impact Statement. Furthermore, five states have already enacted environmental legislation, and others will surely follow. The Environmental Services Project Director for Dames and Moore has stated in the June issue of that company's publication, "Elements," that, "The nuclear power industry has perhaps been most affected to date by the Act [NEPAL but recent court decisions, legislative trends and general public concern will accelerate the spread of the Act's impact on other industries. Mining and petroleum are already involved in environmental affairs." There can be little doubt that within a very short time all environmental aspects of the minerals industry will be strictly regulated and monitored by some agency of Federal and/or state government. Indeed, it is probable that any future effort to extract natural resources will be contingent upon a favorable review of an Environmental Impact Statement. It is also quite possible that continuation of present operations will have to be justified on the basis of proof of an acceptable environmental impact. It is the objective of this paper to present some ways in which remote sensing technology can be applied toward an efficient collection of environmental data necessary for the preparation of an Environmental Impact Statement.

Jan 1, 1972

By K. J. Shoop

Coal-fired power plants in the U. S. produce approximately 20 million metric tons of Hue-gas desulfurization sludge every year. The sludge mainly consists of calcium sulfite and calcium sulfate. This can be converted to synthetic gypsum, which in principle could be a marketable commodity. However, many Hue-gas scrubbers produce sludges that do not meet the quality requirements of the gypsum industry, and so their sludges must be landfilled as a waste. If a suitable method can be developed for removing certain objectionable impurities from the sludge, it will then be possible to market the material instead of landfilling it. A sludge from a natural-oxidation scrubber was characterized, and the main contaminant was found to be calcium carbonate from unreacted limestone. Based on the particle size and the characteristics of the material, froth flotation was considered as a method for purifying the material. Since no flotation studies have ever been carried out to separate calcium carbonate particles from calcium sulfite or calcium sulfate particles, it was first necessary to select a suitable collecting reagent. Based on Zeta-potential studies, the most suitable reagent was found to be an octadecylamine-octadecylguanidine complex. Results are presented for flotation of calcium carbonate from scrubber sludge using this reagent, in a reverse-flotation process. The best results were obtained when the sludge was first pre-cleaned using a water-only cyclone to remove unfloatable coarse limestone, followed by froth flotation to remove fine limestone.

Jan 1, 1998

By J. E. Hoffman, S. P. Sandoval, T. J. Keefe, K. P. V. Lei, O&apos

The U.S. Bureau of Mines investigated the use of the Fe2+/Fe3+-SO2 (FFS) anode reaction in the copper leaching-solvent extraction-electrowinning circuit. The investigation revealed that six process variables, including anode type, Fe 21 concentration, current density, electrolyte temperature, degree of agitation, and manifold injection point were found to influence cell voltage and cell current efficiency. A 47% voltage reduction (0.8 versus 1.5 V) compared to conventional electrowinning with activated lead (ALE) anodes was achieved at a current density of 258 A/m2 (24 A/ft2) with an industrial electrolyte. Current efficiency was maintained above 90%, and S02 above the cell measured less than 1 ppm when activated carbon was used to assist the reduction of Fe" by S02 in the copper electrolyte. Solvent extraction tests showed that Alamine 336 is a stronger H2SO4 extractant than is needed to extract the excess acid produced by the FFS anode reaction.

Jan 1, 1993

By E. Taskin

Diasporic bauxite from the Mugla-Milas region was mechanically activated in a planetary mill for different activation times and the structural changes were examined by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and specific surface area analysis (BET ? Burnauer, Emmett and Teller). Non-activated and activated bauxite samples were leached directly in alkaline (Na2O) solution at atmospheric conditions and the activation procedure led to the amorphization and structural disordering of the diasporic bauxite structure, which increased the dissolution efficiency. Effects of milling speed, liquid/bauxite ratio and leaching time on alumina extraction in direct alkaline leaching of diasporic bauxite were also studied. The alumina extraction was ~7% for non-activated bauxite and ~70% for activated (75 minute) bauxite. Key words: Diasporic bauxite, Mechanical activation, Alkaline leaching, Alumina extraction

Jan 1, 2009