Search Documents

By T. A. Gray

There are several potential large-volume uses for coal ash in mining-related applications that could be environmentally and economically beneficial to mining companies. Actual usage, however, may be constrained by regulations or by perceptions of coal ash and the potential uses. To identify currently allowed uses and to assess constraints to coal ash use in the eastern coal fields, questionnaires were sent to state coal mining agencies to determine their policies on coal ash utilization and to mining companies to solicit their viewpoints on coal ash utilization. Identifying and understanding the constraints will allow for the development of a coordinated and consistent approach to remove or reduce these constraints and possibly allow for increased utilization of coal ash by the mining industry. This paper summarizes the findings of our investigation.

Jan 1, 1995

By Peter T. Chiang

A brief literature review on metal separations by ion exchange and solvent extraction of their thiocyanate complexes which are practiced in analytical chemistry as well as in industries was performed. Owing to the poor stability of free thiocyanic acid in acidic aqueous and organic media, technical and environmental problems which cause high thiocyanate consumptions often arise during the practice of the separation processes. This prompted the conducting of a second and more thorough literature review on the chemistry of thiocyanic acid. The objectives of this undertaking are to compile and interpret literature data on the physical properties and chemical reactions of thiocyanic acid, thus providing a clearer understanding of the causes of these problems and giving options as to how to minimize them. The best answer found for carrying out the separation processes is to keep the temperature, thiocyanic acid concentration and total acidity as low as practical.

Jan 1, 1984

By A. M. Johnson, M. A. Cornachione

The west central Upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur that can create emission problems when processed in a kiln. A low-cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated. In this study, optimal conditions for the bacterium Thiobacillus ferrooxidans were created to promote pyrite oxidation and, therefore, sulfur removal from the slate. Preliminary lab scale flask tests using crushed and sized slate (-40 + 100 mesh) and T. ferrooxidans bacteria in a sulfuric acid medium resulted in 70% oxidation of pyrite over a one-month period. Subsequent column leaching tests on coarser materials (-3/8+1/4 in.) operated for six months resulted in a maximum reduction of total sum of 75%. These data suggest that bio-heap leaching to remove sulfur from the slate for use as a kiln feed material is viable.

Jan 1, 1995

By Cameron Dunn, Callum Fryer, Carmen Hu, Craig Sewell, Peter Stakne, Andrew Raine

The Woodsmith Project is located in north-eastern England within the North York Moors National Park. The strata contains the world’s largest known high-grade Polyhalite resource of around 2.66 billion tonnes. The Project was initiated by York Potash Limited (YPL), a subsidiary of Sirius Minerals plc., but in March 2020, a takeover was completed by Anglo American, one of the largest mining companies in the world. Polyhalite is an evaporite mineral and contains essential nutrients required for plant growth. The Polyhalite will be extracted via two deep mine shafts and transported underground from the mine site to a Materials Handling Facility on a Mineral Transport System (MTS), which comprises a high-capacity conveyor belt system located within a 4.9 m ID tunnel. In 2018, STRABAG were awarded with the design and construction of the MTS tunnel and associated infrastructure, including the high-capacity conveyor system. The scope of work consists of 300 m of open cut, 100 m SCL tunnel, 36.5 km TBM drive (originally anticipated as three separate TBM drives) along with a network of underground caverns at the Woodsmith Mine. The construction of two 380 m deep intermediate access shafts was later awarded as Amendments to the Contract. The tunnel is constructed using a Herrenknecht Single Shield TBM. As a result of how the various elements of the project have developed over time, the first TBM drive has been extended to ~29 km making it the worlds longest single heading TBM Tunnel when complete. The option of completing the entire tunnel length with a single heading TBM drive is currently being assessed by Anglo American and STRABAG. This unprecedented tunnel length requires two intermediate shafts to provide essential access and services, the first intermediate shaft is at Lockwood beck (LWB) and the second is at Ladycross (LDX). The LWB shaft has been constructed utilising the innovative Blind Boring technique never used before in the UK. This paper will explain the methodology and technical risk management associated with this technique. The authors believe that the collaborative approach between all contract partners is and continues to be the important contributor for the success of this project.

Jun 13, 2023

By J. P. McDonald

Exposure to particulates containing metals and metal fumes (PCMMF) is a potential concern in ore refining and smelting. Some metals of primary interest are arsenic, cadmium, copper and lead, which have been linked to various adverse health effects. The current National Institute for Occupational Safety and Health (NIOSH) sampling method for metals in particulates requires the use of a filter, precision airflow pump and laboratory analysis. A major concern with this method is the one-to-two weeks? wait before laboratory results are available for use in determining if additional controls are needed to assure adequate exposure protection for workers. Particulates containing these metals were sampled during sixteen sampling events at a copper smelter using the traditional NIOSH methods. Monitoring of particulates was simultaneously conducted using a TSI 8520 Dust-Trak real-time aerosol monitor with a 10-µm-cutpoint sampling inlet. NIOSH analytical methods related to particulates and metals (methods 0500, 0600 and 7300) were used to determine particulate mass and individual mass contributions of metals on sample filters. Linear regressions with y-intercepts forced to zero were developed to determine the relationship between the PM10 measurements recorded by the DustTrak and laboratory-reported total particulate mass, PM10 and respirable arsenic, cadmium, copper and lead concentrations. These linear regressions yielded correction factors that can be applied to DustTrak readings to obtain total particulate mass, PM10 and respirable concentration estimates for each of the four metals. The R2 (coefficient of determination) values from the linear regressions ranged from 0.65 for total lead to 0.91 for total copper. These results suggest that the DustTrak may produce real-time data useful in providing estimates for airborne concentrations of arsenic, cadmium, copper and lead in copper smelter particulates.

Jan 1, 2011

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries -Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By S. A. McGhee

ASARCO Incorporated embarked on a modernization and expansion program to improve overall operating efficiencies and to more effectively develop the large mineral reserve at the Ray Complex Open-Pit Mining operation located near Kearny, Arizona. Major elements of this Ray Modernization and Concentrator Expansion Project included engineering and construction of a 54,400 MTPD (60,000 STPD) In-Pit Crusher and Overland Conveying System. and a 24,200 MTPD (30,000 STPD) Copper SAG Concentrator and Tailings Disposal System. Detailed engineering, procurement, and construction management were initiated in November 1989 under contract with Bechtel Corporation. Field construction commenced in May 1990 leading to mechanical completion and start-up during February 1992.

Jan 1, 1993

By Donald P. Moore

During April 1967 a Frasch sulfur mine was placed in operation near Fort Stockton, Pecos County, in West Texas. This was the first Frasch mine to recover native sulfur from a deposit not associated with the caprock of a salt dome. Since 1967 two additional mines have been opened in west Texas, another one near the first at Fort Stockton and a third one near Orla in Culberson County (Figure 2). Recoverable reserves at the Culberson County mine are estimated to be 57,000,000 long tons of native sulfur (Zimmerman and Thomas, 1969). Total recoverable reserves at the three mines probably exceed 60,000,000 long tons, Studies of the geochemical cycle of native sulfur mineralization in test Texas indicate an origin similar to the deposits on salt domes although the geologic framework is different. A comparison of the geologic setting of the west Texas deposits with the deposits in the Union of Soviet Socialist Republics as reported in the literature, reveals many similarities. ACKNOWLEDGEMENTS The writer wishes to express his appreciation to Cities Service Minerals Corporation for support throughout this study. Special thanks are due Dr. Chris Riecken and Mr. Dave Hardy for their

Jan 1, 1971

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015

By C. RAMADINI, F. NURJAMAN, A. SHOFI, B. SUHARNO

Nickel demand is increasing along with the rising need for stainless steel and other alloy steel/iron. The small addition of nickel in such materials can improve impact strength, ductility and corrosion resistance. Nickel is generally obtained from nickel sulfide ores (nickel associated with sulfur) and nickel laterite ores (nickel associated with iron and magnesium silicate). Almost 60 percent of nickel is now produced from sulfide ores, despite its existence in sulfide ores being less than in laterite ores. However, the depletion of sulfide ore reserves makes the mastery of nickel laterite ore processing of important and immediate concern. Selective reduction followed by magnetic separation has been in development in lateritic nickel ore processing to overcome the issues of high energy consumption and pollution associated with conventional pyrometallurgy methods such as blast furnace and rotary kiln electric arc furnace (RKEF).

By J. R. Batista

Leachates from gold heap-leaching mines contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina when using relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for full-scale activated alumina processes. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH > 5.0. Silica adversely affected the selenium adsorption capacity. At pH values < 4, silica was poorly adsorbed by alumina and selenium adsorption was improved.

Jan 1, 1994

By Bernard L. Merlo

INTRODUCTION Modern mine management is constantly striving to develop improved mining methods which will not only increase productivity, but will also provide a safer work environment and make the most efficient use of our natural resources. Progress can be seen in this area by tracing mining methods through history. Work that was originally done with hand tools progressed with the age of mechanization to conventional mining, matured to continuous and longwall mining, and the advent of short¬wall mining, a combination of continuous and longwall, has recently been seen. This new method of shortwall mining provides a promising method for safe and ex¬pedient coal extraction. This study focuses upon the planning, design de¬velopment, and operation of the first producing short¬wall unit in the US which was operated in the Pittsburgh coal seam in northern West Virginia. MINE DESCRIPTION The mine is located in northern West Virginia at Grant Town in the heart of the high volatile Pittsburgh coal seam. Originally opened in 1901, the mine has be¬come one of the largest in the US, encompassing an area of approximately 103.6 sq km (40 sq miles). The seam being mined was the high volatile Pittsburgh seam which ranged in thickness from 1.8 to 2.96 m (6 to 91/2 ft). Three types of mining methods were employed: con¬tinuous mining, longwalling, and shortwalling, with each type accounting for 50%, 30%, and 20% of total pro¬duction, respectively. A total of 630 contract and super¬visory personnel were employed to produce the mine&apos;s designed annual tonnage of 1.8 Mt (2 million st). There were ten producing sections, eight continuous miners, one longwall, and one shortwall, operating a total of 22 unit shifts per day. Eight shafts, varying in depth from 80.2 to 194.2 m (263 to 637 ft) provided entrance to the Pittsburgh coal seam. These shafts were used for ventilation, portaling, coal hoisting, supply, and emergency escape hoisting. Ventilation was achieved by means of three exhaust fans which provided 707.9 m3/s (1.5 million cfm) of air to the mine and removed approximately 141 584 m3 (5 mil¬lion cu ft) of methane per 24 hr period. The room-and-pillar method was used for secondary recovery with designed barrier blocks between panels of 61 m (200 ft) in width. A double row of blocks was left around each gob area to provide efficient bleeder action

Jan 1, 1982

By Q. Xiao, R. Naidu, W. Li, S. Song

Acid mine drainage (AMD) derives from the oxidation of sulfide minerals, primarily pyrite (FeS2), and is the most severe environmental issue facing the minerals industry. The most common short-term approach to AMD treatment is migration control, such as acid neutralization and metal/metalloid and sulfate removal, through the addition of alkaline materials, including lime (Ca (OH)2), limestone (Ca CO3), gangue minerals and industrial wastes. This requires the continuous input of materials and may result in the production of a vast amount of secondary sludge requiring further treatment and disposal. Addition of chemicals is usually more important in metal/metalloid removal than in sulfate removal unless the sulfate is present in very high concentrations. A more promising long-term strategy for AMD prevention is source control through the complete removal of pyritic minerals and encapsulation of potential risk minerals by coating with impermeable surface layers. This is regarded as the most cost-effective approach, although the mechanisms underpinning this and the implementation procedures are yet to be fully elucidated. It is likely that long- and short-term practices can be combined to optimize the remediation of contaminated mining sites. Some factors such as differing geological and mineralogical characteristics and transportation costs must also be considered for the successful implementation of AMD prevention and remediation strategies. This review also considers some implications for AMD remediation, but the promising bioremediation of AMD is not discussed as it has been extensively reviewed.

By Milton Hood

The Copper Flat Property is located approximately 6 miles NE of the small town of Hillsboro in Sierra County, N. M. (Fig. 1). Hillsboro was the center of considerable mining activity in the late 1800&apos;s and early 1900&apos;s following the discover, of gold bearing vein deposits and later discovery of, placer gold along the east slopes of the Animas Hills. The Copper Flat orebody is a porphyry type deposit occurring in a small quartz monzonite porphyry stock that has intruded the center of a circular andesite plug (Fig. 2). The primary ore mineral is chalcopyrite. By-product values are contained in gold, silver and molybdenum.

Jan 1, 1983

By P. D. Pack, E. H. Skinner

During design of a 550-foot rectangular shaft in alluvium, lateral support within the excavation was an anticipated construction problem. Actual experience showed that the nearly 9 x 14 foot excavation required no lateral support. A strain measurement program con- current with construction and for a 9-month period following completion of the shaft detected only minor strains. Shaft design included consideration of available geological information. Site exploration included a 754-foot drill hole, cored at selected intervals, and a suite of geophysical well logs. Generalized physical properties of the alluvium were developed from laboratory core testing. An elasto-plastic, finite element computer program (DAHLKE) developed by the Spokane Mining Research Center U.S. Bureau of Mines, has been recently used to analyze the behavior of the alluvium around the shaft. Analysis showed that yielding first develops in the shaft corners and progressively expands into the wall zones around the shaft as loading increases. Gradual growth of a plastic zone progressed outward from the excavation boundary at increasing loads but had limited extent and was surrounded at all stress levels by an infinite elastic zone. This design review, aided by computer analysis, confirmed that the shaft would have been considered theoretically stable as designed.

Jan 1, 1977

One of the largest mining shows in the world is set take place April 15-18 in Santiago, Chile. Expomin 2008 is expected to attract more than 60,000 professionals from around the world who are involved in all aspects of the mining industry. Expomin has become an important place for mining leaders to meet, organizers said, ?with great expectations for the development of new business in international markets.? This is the 10th Expomin. The event, held every two years, is expected to at-tract exhibitors from more than 25 countries, representing nearly 1,000 companies and more than 3,000 brands related to the mining industry, organizers said. Most all of the world?s largest equipment manufacturers and suppliers ? surface and underground ? will be represented. The importance of the event to the Chilean and international mining industry can be seen by the increase in size of the exhibition ? 13 percent more surface space in 2008, compared with the 2006 Expomin. The exhibit will be broken down into four pavilions, covering 34,054 m2 (355,570 sq ft). An outdoor area for the large mining equipment will cover 16,120 m2 (173,520 sq ft).

Jan 1, 2008

By T. A. Farr, I. A. Gibbs, F. Guevara, S. R. Simms, G. Nojima

This paper describes an installation of a medium-voltage adjustable frequency motor drive (AFD) on a high starting torque regrinding mill. This type of application is typically found in the mineral industry dealing with hard ore. The AFD electrical architecture is introduced from line to load. The type of closed loop encoder feedback motor control algorithm is briefly described. The results of the AFD motor identification auto-tuning are compared against the manufacturer’s supplied data. The motor drive performance results are shown for pre-ramp DC fluxing, high starting torque with overload current, excessive load torque stall condition, and blocked rotor. The instrumentation and arrangement for the two watt-meter method to capture low frequency data are presented. The data shown is from the input power quality meter, the AFD computer tool, the output motor protection relay, an oscilloscope, and load shaft connected strain gauge (rotating telemetry for torque assessment). These types of high starting torque constant torque loads are found in mining and process industry applications employing AC adjustable frequency drives. Using field results should help demystify the use of voltage matching output transformers in AFD applications including constant torque loads

Mar 2, 2022

By M. R. Peterson

The U.S. Bureau of Mines has investigated new methods for increasing the selectivity in flotation by creating and regulating reagent concentration gradients within flotation columns at steady-state operation. Gradients were generated and traced in a water-only system with the use of fluorescent dyes, and the effects of various operating parameters on these gradients were investigated. From this investigation, it was found that both gradual and steep gradients could be generated in the froth cleaning zone, and that these gradients could be changed through the manipulation of both physical and chemical operating parameters. The application of reagent-gradient control to mineral systems could improve both flotation grade and recovery in commercial flotation operations without the use of additional flotation circuitry.

Jan 1, 1992

By Perry M. Jones

An important operational and environ-mental concern associated with in situ leaching activity is the balance between solution injection and recovery. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. The Bureau of Mines is investigating the factors that affect solution balance in an unsaturated ore deposit, as part of ongoing in situ leaching hydrologic investigations at the Cyprus Casa Grande Mine. Flow conditions in 58 injection and recovery wells at the Casa Grande In Situ Leaching Test Facility were monitored daily over an 18 month period. Changes in the balance between injection and recovery occurring during this period were evaluated using analytical and statistical methods. The results permit estimation of solution distribution and the volume of solution stored in microfractures and interstitial pore spaces within the deposit following 18 months of leaching. Approximately half of the difference between well injection and well recovery can be accounted for by solution movement through macrofractures into nearby drifts. Estimates of solution storage within the ore deposit at the end of 18 months of leaching range from 3.5 to 6.9 pet. of injected solution. These results also suggest that 13 to 26 pet. of the fracture/interstitial pore space in the deposit was saturated with solution after 18 months of leaching.

Jan 1, 1991

By V. S. Znamensky, R. V. Stewart

This chrysotile asbestos ore body is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 miles) north of Montreal, 480 km (300 miles) north of the tree line, and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1% mile) in length, some 61 m (2OO ft) in width and plunges at 25o to 30 o below surface to a vertical depth of at least 610 m (2000 ft). The ore body was originally evaluated by programs of surface mapping, diamond drilling, and bulk sampling. The fiber is semicrude, possesses excellent strength, and good fiber length distribution. GEOLOGICAL SETTING, LOCATION, AND DISCOVERY The chrysotile asbestos mineralization at the Asbestos Hill mine occurs in serpentinized ultrabasic rocks of Precambrian age. These intrusive rocks are found in older volcanic sedimentary rocks known as the Cape Smith-Wakeham Bay belt and are shown in Fig. 1. The rocks comprising this belt overlie older basement rocks composed of granite and granite gneiss. This belt has a width of 32 to 64 km (20 to 40 miles), and trends in a general east- west direction, a distance of about 370 km (230 miles) from Wakeham Bay on the east coast of the Ungava Peninsula to Cape Smith, located on the east side of Hudson Bay. Two sequences of rock have been recognized in this belt. The lower (oldest) rocks are known as the Povungnituk group, and consist principally of massive lavas and sediments. The upper (younger) rocks are known as the Chukotat group, and are composed of pillowed lavas with interbedded sedimentary rocks. Sills of ultrabasic rocks exist in both younger and older rocks, but are more often found in the Povungnituk group. Concentrations of chrysotile asbestos, as well as nickel and copper minerals are found at or near the base of ultrabasic sills, and are most common where a change in dip occurs. The mine is situated about 1818 km (1130 miles) north of Montreal, approximately 1126 km (700 miles) north of the start of continuous permafrost, and about 482 km (300 miles) north of the tree line. The depth of permafrost at the mine site has been calculated to be approximately 549 m (1800 ft). This rich deposit of asbestos was discovered in 1957 during extensive exploration for nickel in the Ungava nickel belt. During that year, traverses conducted by Murray Watts spotted interesting looking ultrabasic rocks, and followup ground examination disclosed rich surface showings of asbestos mineralization near the present open pit. In 1958, a two-man prospecting party returned to the discovery site and a mineral exploration license was granted to Fig. 1. Location map Keewa Quebec Mines Ltd., a wholly owned

Jan 1, 1986