Search Documents

By James E. Brewer

Procedure for approval by the U. S. Army Corps of Engineers of a new source of aggregate is in three phases. Phase 1 consists of an investigation of a quarry or proposed quarry by district geologist and laboratory geologist and/or petrographer. The quarry face or suitable outcrop is logged in detail or, if exposures are poor, cores may be taken to determine whether further investigations are warranted. Phase 2 consists of thorough laboratory testing. Cores and crushed material are subjected to a number of acceptance and quality tests for soundness, absorption, abrasion, reactivity, and other properties. Petrographic analysis is also made. Phase 3 is a physical and economic study of the site and involves determining quantity of stone avail- available, amount-and character of overburden, condition of haul roads and distance to rail shipping point, plant flow sheets and capacity, aggregate sizes produced, and approximate price of material at plant.

Jan 1, 1966

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979

By T. Wohlford

Due to the increases available base of scientific knowledge, increased independent review required by worldwide security exchanges, and the need for accuracy in characterizing mine water resources, it has become necessary to produce a more accurate hydrologic balance. This presentation provides a critical review of the steps and tools to compile a complete hydrologic review of a mine property. The forces of regulation, increased scientific analysis, better tools, and stakeholder expectations have created a perfect storm of accuracy demand. Ausenco has developed protocol to achieve the desired end.

Feb 23, 2014

By Lok W. Home

HISTORICAL DEVELOPMENT At the beginning of the 1970 more than 90% of pro¬duction drilling in open-pit mining was obtained with the use of rotary drills. At the same time, the use of rotary drills underground was virtually nonexistent. Several progressive mines began questioning whether efficient rotary drilling could not be adapted to under¬ground applications. In the late 60s and early 70s at¬tempts to use rotary drilling were made by Inco, Ltd. and Meramac Mining, utilizing drill units designed as a combination of small diameter raise drills and rotary drills. These initial attempts were unsuccessful primarily due to the immobility of the equipment and low degree of dependability. At the same time, experiments con¬ducted by Inco and Meramac using large diameter in¬the-hole percussion drills produced immediate encourag¬ing results. The first serious attempt at utilizing rotary drilling underground was made by Texasgulf in 1971 at Kidd Creek mine in Canada. An experimental stope 15 m wide, 36 m long, and 30 m deep was drilled using 200-mm diam rotary drilled holes. The machine used was a Robbins' Model 11 D. The Model 11D is a rotary drill designed to drill drain and utility holes under¬ground. The results of this test revealed that large diameter blasthole stoping was feasible. The indications were that the major areas of concern-fragmentation and pillar damage-could be controlled and a new low-cost stoping method resulted. At this point Texasgulf and Robbins entered into a cost-sharing agreement to develop a rotary drilling unit specifically for this stoping method. Drilling of the trial stope required pouring a concrete pad at each drill hole plus anchoring the derrick to the pad by means of rock¬bolts. Utilization expressed in terms of drilling time to available time was less than 20%. It was obvious that the required unit had to be mobile, setup time had to be minimized, and rod handling had to be improved. The first attempt at an underground production-type rotary drill consisted of mounting the basic 11D on an air-powered Eimco 600 Series crawler. The crawler was equipped with four screw-type leveling jacks operated by an impact wrench; rod rack facilities for 60 m of 1.2-m long, 170-mm diam rods; a rod handling facility consisting of an air-lift swing boom and a pipe loader which automatically positioned the rod under the float¬ing drive box; a turnbuckle anchor system requiring in¬stallation of four rockbolts in the drill drift floor and placing turnbuckles from the rockbolts to the corners of the drill; and trailing power units containing the electrics and hydraulics required to operate the drilling unit. Operation of this unit revealed a vast improvement in drilling time but some problem areas remained. The anchoring system required secondary drilling and proved difficult to adapt to the localized irregular floor surface and the trailing power unit was difficult to maneuver and was causing unnecessary maintenance costs. Addi¬tional improvements resulted in the standard 11MD rotary blasthole drill. DESCRIPTION OF UNIT This standard model consists of the drill and the power unit integrally mounted on an air-powered crawler chassis (Fig. 1). The rod-handling and leveling¬jack systems are similar to those used on the prototype Texasgulf unit and remained relatively the same. The anchoring system has been replaced by the roof jack, initially screw type but now hydraulically actuated. The anchoring system is necessary as the drill exerts more thrust than the weight of the unit. During operation it is found that the two front jacks adequately anchor the machine. The complete unit's operational dimensions are: height, 3.2 m; width, 2.1 m; and length, 4.2 m requiring a 3.5- x 3-m drill drift. The derrick is pivot mounted and raised and lowered by a hydraulic cylinder reducing the transport height to 2.5 m. The derrick is also turnbuckle mounted to allow dip angle drilling from vertical to 0.52 rad (30°) off vertical. The drill derrick can be mounted to allow dip axis to be parallel or perpendicu¬lar to the long axis of the unit. The standard rods are 1.2 m in length and are contained in racks of 10 which can be removed for transportation. Drilling torque is produced by a 56-kW (75-hp) electric motor driving a double vane pump which in turn drives a Robbins high torque gear-type hydraulic mo¬tor. In addition to the hydraulic motor, the machine drive system has a 3.9:1 planetary gear reducer. This results in six speeds with the following minimum and maximum range: Maximum rpm 112 Torque 3725.5 J (380 kg m) Minimum rpm 10 Torque 14 706.0 J (1500 kg m) Drilling thrust is provided by two bootstrap cylin¬ders pressurized by a variable volume pump. This sys¬tem can produce from 0 to 267 231.2 N thrust in either direction. Bailing air (approximately 17 m3/min at 382.2 to 490.3 kPa) is introduced through a rotary swivel pass¬ing directly through the center of the drive system to keep efficiency and losses to a minimum. Hole annulus is also kept to a minimum by using 170-mm rod when drilling a 200-mm hole. A small amount of water is added to the air for dust suppression. The machine has to be supplied with air, water, and electrical power. It does not appear feasible to provide an integral air power supply with the rotary drill such as is done with open-pit rotary drills. Air is required and installed during the primary development of the drill drift. The machine can be adapted to drill hole diameters from 170 to 228 mm for blasthole operations. The drill string consists of the rotary bit, crossover stabilizer, roller stabilizers, and standard rods. The operator controls speed and thrust pressure from an operating console which can be mounted in a conve¬nient position. Mount Isa has made an adaption to the operating console to permit remote collaring of drill holes in an uncleared floor.

Jan 1, 1982

By K. E. Burgher

Since World War II, the need for the use of explosives in construction, mining, and quarrying near congested urban areas has increased dramatically. Often times a coal mine, once isolated from a city, finds itself surrounded by residential and commercial structures. The United States Bureau of Mines and others have researched blast design to a point where ground vibration and airblast damage can be avoided. A problem still exists, however. It is the fact that people often react to only the loud noise associated with a blast although it may not cause damage. Most often it is the concussion of a blast, less than 20 hertz and inaudible, that produces damage. Public fear from the "startle" and "fright" of loud blast noise greater than 20 hertz leads to the complaints which are generally unfounded. See Thackray, Touchstone, and Baily (1975) for a further discussion of the startle effects of loud sudden noises. When blasts are designed in accordance with U.S.B.M. specifications, management generally has little to worry about with respect to damage claims. Complaints, however, still arise when the noise is accentuated from the blast. It is meteorological conditions which dictate how the sound levels will propagate. Some mines use small pilot test shots (generally one-two lbs) to determine when atmospheric conditions favor sound travel.

Jan 1, 1987

By R. Worrall

The global mining industry has been proactive over the last decade in finding ways to embrace the concept of sustainability. However, legacy mine sites (which include abandoned derelict and orphan mine sites) across the world continue to present issues for the global mining community, governments, local communities and NGOs. Unfortunately there has been much less academic focus on this area of mining and sustainability. This paper seeks to address how principles of sustainable development can be used to guide the development of processes for addressing post mining landuse issues for legacy mining areas. This is being done using a case study area located near Ipswich, in southeast Queensland, Australia. This area has a 160 year history of coal mining, and was one of Queensland?s crucial early industries. Mining in the area ceased in 2003 leaving a degraded landscape covering an area in excess of two thousand hectares adjacent to one of the fastest growing urban areas in Australia. A sustainability criteria and indicators framework for post-mining landuse on legacy mined land, developed from current best practice used for measuring sustainability across a range of industries is being developed. A review of current best practice suggests the framework should: (1) consider in equal measure environmental, social and economic factors; (2) have a minimum number of indicators which should be easy to identify and measure; (3) must have indicators with a meaningful output; and overall, the framework must consider particular requirements of the site being investigated. Application of the framework to the case study area is an ongoing aspect of this research, and the results will be evaluated through the use of expert stakeholders.

Jan 1, 2007

By R. A. Matuszak

In recent years, a new concept in the control of electrically powered excavators has come into existence. The new type of control system has come to be known as "static" control. The use of the name "static" to describe this system is somewhat misleading since this term refers only to one of the many advantages of this very important advance in excavator control systems. In 1959, the first truly "static" control for Ward-Leonard equipped electric excavators was designed, developed and placed in service. The control system, originally intended only as a more modern electronic type of alternate to the tried and proven rotating amplifier control system then in use, has since proven to be much more.

Jan 1, 1964

By Y. H. Alghamdi, A. D. S. Gillies

"INTRODUCTION Background Diesel Particulate Matter (DPM) has been a critical issue during the last decade in underground mines. This problem is threatening the health of mine workers, as well as the mine’s productivity. It has been confirmed that the diesel engine exhaust is the main source for the diesel particulate matter (DPM), and that it has the highest impact in raising carbon monoxide, carbon dioxide, oxide of nitrogen, and hydrocarbons in the underground environment. Miners who are exposed to this kind of emission are at high risk for developing lung cancer and other lung diseases. The Mine Safety and Health Administration (MSHA) has issued standard rules to regulate diesel emissions in underground mines. The final ruling confirmed in 2008 that the total carbon should not exceed 160 µg/m3. (MISHA, 2008) Monitoring DPM in underground mines has become important to ensure compliance with the MSHA regulations. There are many different types of DPM monitoring systems that are currently being used in underground mines. Two methods are typically used for DPM sampling: the personal sampling method or the direct exhaust sampling method, which takes a direct sample from the engine’s tailpipe. Many mines do not recommend using the direct exhaust sampling method since it involves complex measuring equipment and procedures, as well as it is not regulated in the United States or Canada. Thus, the personal sampling method is the preferred method in many mines when taking DPM samples. Even this method includes many variations, such as the Respirable Combustible Dust (RCD) method and the method devolved by the National Institute for Occupational Health and Safety NIOSH 5040. The NIOSH 5040 method is the preferred method overall because it gives more accurate measurements compared to the other methods. This method does not allow organic carbon sources other than those coming from diesel engine exhausts to interfere with the measurements, which otherwise would lead to overestimating the actual amount of the DPM in the mine environment. An impactor feature in the cassette, which holds the samples in the instrument, characterizes this method. Since the diesel particles are less than 0.9 micron, this impactor does not allow particles more than 0.9 microns to be collected in the cassette filter. The cassette is then analyzed in a lab and the concentrations of organic carbon (OC), elemental carbon (EC), and total carbon (TC) are determined. Lately, the National Institute for Occupational Safety and Health (NIOSH) has developed a new instrument that can use the same concept of NIOSH 5040, but with instant measurements of elemental carbon. It utilizes laser radiation with the cassette so it can give a real time measurement. The real time measurements give instant information about the underground environment that will allow the mining engineer to take immediate action and enact plans instead of waiting for results from the laboratories where NIOSH 5040 method may take several weeks to get the measurements."

Jan 1, 2016

By P. C. Thakur

Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1952 at the Humphrey Mine of Consolidation Coal Company for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for eight years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300-to 600 m, with reasonably precise directional control and within practical cost limits.(1) Mining Research Division of Continental Oil Company, the parent company of Consolidation Coal Company, began a research program in the early 1970's to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary Its of this research have already been published.(2) To date nearly 4500 m of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: 1) The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3 percent in course of two to three months from original values of nearly 0.95 percent.

Jan 1, 1979

By V. F. Hollister

Although it is apparent that porphyry copper deposits may have formed in the Andean orogen from Permian time onward, commercial deposits thus far developed appear to have Cenozoic ages only. Following Chilean useage, the porphyry deposits are divided into either: (a) a stockwork, or (b) a tourmaline breccia model. Stockwork type deposits tend to occur on major strike-slip structures which may be either transcurrent or transverse faults related to plate movements, while the tourmaline breccia type may more frequently form independently of regional faults. Stockwork types may be conjugate fractures that intersect and ramify as a network of veins and veinlets, cutting altered rock, and genetically related to a major regional fault, or in other cases they may reflect the intersection of two large fault structures. Circular fracture patterns may more rarely occur in stockwork deposits in response to a specific intrusive. Tourmaline breccia types are characterized by circular and radial fractures genetically connected in some way with tourmaline breccia pipe development or an intrusive piercement that preceded it. Each structural model contains mineralized intrusive8 which have a close time-space relationship to ore and in each model, mineral paragenesis is similar, regardless of age or location in the plate. Also, each model contains the same type of alterntion halos (phyllic, argillic, prophllitic) as are developed in intru- sive centers in porphyry copper deposits found in North America. The potassic zone is exposed best in the older deposits. Examples of each type of deposit are illustrated, demonstrating the feature evolved.

Jan 1, 1973

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,300 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for the mining designs and operations in the Leeville underground mine.

Jan 1, 2010

By H. Colijn

Vibratory or oscillatory conveyors can be found in all types of industry, handling virtually any granular bulk material, often at elevated temperatures. These conveyors can be combined with other process functions, such as screening, cooling, drying and dewatering, while conveying. Although construction and installation is relatively simple, the engineering and design analysis of the vibratory mechanics is fairly complex. This paper will discuss the basic types of vibratory conveyors and the analysis of the material movement along the carrying trough.

Jan 1, 1985

By P. J. Arps

Cyanide (CN) is used to recover gold from its ores in many locations worldwide. In spite of the established history of gold mining in Alaska, modern cyanidation methods have been used at only one location, the Ryan Lode Mine at Ester Dome, near Fairbanks. Ore was processed by heap leaching between 1987 and 1989, when permitting issues caused operations to be terminated. Those issues have since been resolved, and plans to reopen the mine are currently being discussed. Plans are also proceeding to develop several other ore deposits in the state, all of which include the use of cyanide for gold recovery [6]. Since tailings and effluent water produced from these mines will require treatment, it is important to develop detoxification methods suitable for the Arctic and sub-Arctic conditions found in Alaska. Several methods exist for removing cyanide from mining wastewater. However, most industrial users prefer chemical treatment systems, and typically use sodium hypochlorite, hydrogen peroxide, or sulfur dioxide/air/copper to oxidize free and complexed cyanides [9]. Biological treatment has been used successfully at two sites in the United States [30,32] and field tested at several others [20,27,28]. In addition, one mine uses "natural processes", which include natural oxidation, photodegradation, and degradation by naturally occurring bacteria [33].

Jan 1, 1994

By P. D. Chamberlin

Agglomeration for the heap leaching of gold and silver ores can be defined as the process of attaching fine ore particles (less than 100 mesh) to coarser particles so the fines are immobilized and uniformly distributed throughout the heap, thus making the heap more porous and uniformly permeable to the flow of a leaching solution. Agglomeration techniques and equipment to be described include drum and disc agglomerators, stockpile and belt agglomeration, and the use of vibrating deck and reverse running conveyors.

Jan 1, 1986

By S. Lefond

A glance at the accompanying table and a review of contributors' comments suggest that the industrial minerals industry is recovering from the recession of the past few years. Actually, the total value of nonmetal production in 1983 was $15.5 billion, up 10% over 1982. Nonmetallics still have not recovered to 1981's high of $25.3 billion, but at least it is on the way up. It is significant that cement (+20%), clays (+13%), gypsum (+16%), sand and gravel (+12%), sodium carbonate (+7%), and crushed stone (+11%) are up. These commodities are largely used in the housing and construction industries. Raw steel and steel mill products, iron ore production and castings, and purchased scrap are showing improvement and increased in value last year. They are, however, still not up to the high of 1981. These industries consume considerable amounts of many industrial minerals, such as limestone, dolomite, fluorspar as fluxes, and many types of refractories.

Jan 5, 1984

By S. S. Peng

An expert team consisting of geology, civil, and mining engineer professors was organized to investigate several problems of longwall mining in three mine sites including: site investigation, panel layout and support selection, overburden strata movement, surface subsidence and structural damages, slope, stability, well and stream dewatering, etc. The results include the development of a PC software package such as powered support selection, Surface subsidence prediction, optimum panel dimension, and pillar design.

Jan 1, 1989

By Keith A. Heasley

Historically, the surface subsidence over underground coal mines has been predicted using empirical profile or influence functions which have little or no connection to the actual mechanics of the subsidence. Without a mechanistic basis, establishing the exact site-specific parameters to use in these empirical methods has been problematic. A practical subsidence predictive method based on mechanics has the appealing capability of allowing the determination of site-specific parameters from fundamental properties of the overburden with minimal field calibration work. This paper presents several case studies where a mechanics-based, boundary-element program is used to back-calculate the surface subsidence associated with various panels at several Northern Appalachian coal mines. The program used in this case study is called LAMODEL, and it incorporates a frictionless, laminated overburden into a general purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin scam or vein type deposits. In this paper, the program is used to calculate both the underground convergence and the resulting surface subsidence at five longwall panels and a room-and-pillar section. The fitted subsidence from the model is compared with the field measurements and analyzed. The results from the case studies in this paper demonstrate that the laminated model with calibrated properties can easily provide moderately accurate subsidence predictions and is fairly flexible for fitting measured subsidence. However, additional subsidence predictive case studies arc recommended in order to ultimately evaluate the potential of the laminated overburden model for practical subsidence prediction

Jan 1, 1999

By H. Maleki

Roof falls continue to affect productivity and safety in U.S. coal mines in spite of significant increases in support utilization in recent decades. To minimize roof stability problems while controlling support effectiveness, the U.S. Bureau of Mines is conducting research on support and ground monitoring techniques. Practical implementation of this research is presented in this paper. Instruments to monitor rock mass deformation, support loads, and microseismic emissions have traditionally been used to assess roof stability. Controlled-source seismic surveys are being used as well. In this paper, measurement techniques are reviewed, and the effectiveness of deformation measurements is demonstrated. This is achieved by an analysis of deformation history from four case studies in room-and-pillar retreat mines. In spite of differences in geologic, geometric, and support conditions in these mines, roof behavior is shown to have been similar prior to failure. The rate of roof movement is suggested as a reliable indicator of roof stability.

Jan 1, 1993

By T. McCallum, C. Cooper, B. Hutzler

"In copper solvent extraction, managing the quality of the organic phase is a key parameter to ensure optimal physical and metallurgical performance in the plant. Increased throughput as a result of declining ore grades coupled with advances in plant design and practice, resulting in reduced organic losses, has pushed the limits of the status quo with respect to organic quality. Clay treatment of plant and recovered organic at the optimal dosage is critical in maintaining quality, however, achieving the optimal dosage through existing filtration capacity and practice can be difficult. Cytec has developed a process aid that increases efficiency of existing filtration equipment that has been successfully implemented at two commercial SX operations. ACORGA® CB1000 enables higher dosages of clay while allowing for more efficient use of existing filtration capacity. This study analyzes results from commercial trials and demonstrates that improved organic quality and clarity is achievable through optimization of current treatment practices. INTRODUCTION Decreasing ore grades have prompted copper solvent extraction operations to raise PLS flow rates, increasing plant throughput to maintain production1. The ability to process higher flow rates through existing mixer-settlers historically came at the expense of increased entrainments2. However, advances in mixer-settler design, practices and improvements in organic recovery processes have enabled operations to maintain, and in some cases reduce organic losses while achieving higher flow rates through existing equipment. Based on the increased demand on the SX equipment and reduced losses (or more efficient recovery) maintenance of the circuit organic quality through efficient clay treatment is now more important than ever. This paper discusses common industry practices and related issues in organic clay treatment, and presents benefits achieved in commercial operations through the use of ACORGA® CB1000 Clay Binder. IMPROVEMENTS IN DESIGN AND PLANT PRACTICE Mixer-settler design has improved since the first commercial copper SX operation in the late 1960s. Advanced designs in mixer, settler, and settler internals have contributed to reductions in entrainments. For example, improved impeller designs have been reported to decrease organic in aqueous entrainment from the ‘old designs’ of 50-200 ppm3 to as low as 4 – 10 ppm confirmed via diluent and reagent consumptions . Similarly, operations are reporting a 20-50% decrease in reagent consumption when compared to the original design criteria3. Operations have optimized settler internals to increase coalescence and have improved settler operating practices which have been shown to reduce entrainments7. Comparison of the SX world operating data from 1999 and 2007 shows reductions in organic entrainment losses with increases in flow rates."

Jan 1, 2015

By Luc Morin

What you don't know won't hurt you! This attitude can get you into trouble when considering your process! When trying to extract the most and the best possible performance from a mineral processing circuit this should be reworded to say: What you don't know about your process will hurt your profits! Today, with the popularity of joint ventures, custom milling contracts and process audits by specialists, not knowing is a formula for trouble! Good Sampling Systems are no longer considered a luxury' Not too long ago the practice of grab sampling was considered acceptable and became the norm. Today, it is rare to hear metallurgists say, "All I need is a trend not a good representative sample. so I'll just grab a sample every few hours." Buyers and sellers of quality products have found that grab sampling leads to poor partnerships'

Jan 1, 1999