Search Documents

By B. Qiu, Y. Luo

Longwall and/or room-and-pillar mining operations in multiple coal seams may not only induce subsurface and surface subsidence but also cause interactions between these mined coal seams. The interaction might destabilize underground mine structures and subsequently induce additional strata movements. Mathematical models to use the predicted subsurface deformations to assess the interactions and the consequences have been developed. The models are incorporated into a computer program, CISPM-MS, for predicting the final surface movements and deformations, as well as the mining interactions associated with multiseam coal mining operations. It predicts final surface movements and deformations caused by the individual mining operations and by the interactive effects. The program can also be used to assess mine structural stability in multiseam mining operations. The paper presents the developed interaction models and their application in surface subsidence prediction caused by multiseam mining operations. A case study involving mining in two coal seams, using longwall and room-and-pillar mining methods, respectively, will be used to validate the program.

Jan 1, 2013

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By H. F. Haller

Large volume sand plugs are placed in tunnels to stem underground explosions at the Atomic Energy Commision's Nevada Test Site. Placement through long, narrow accessways is like stemming coyote holes and blast chambers in mining and construction. Experience with several other methods showed that pipeline conveying could be preferable. Small scale tests justified predicting a placement rate of 20 y. p. h. at 1000 feet, with a modified gunite placer. The initial production trial placed over 2000 c. y. and was estimated to effect a small cost saving after paying for new equipment. Initial problems included duct replacement and supply delays, dust, and other personnel hazards. Operations analysis and SOP'S reduced delays during the second field trial, minimized hazards, doubled production. Re cent re search and operations analyses produced data on abrasion resistant ducts, identified minor equipment modifications which can improve production, developed techniques for impact compaction to 90% ?maximum? and for extension of the practical range to 2000 feet. Twenty-two illustrations include an air consumption-distance chart.

Jan 1, 1967

By Robert M. Cox

A thorough geological engineering investigation is required before surface lands overlying abandoned underground mines can be safely recommended as building sites. The major problems confronting the geological engineer are assembling accurate geologic and mining information and developing an accurate rock mechanics model of the situation. A successful investigation requires a combination of technical expertise in rock mechanics and engineering geology tempered with practical engineering judgment. The results of a good study are not always favorable to the prospective builder.

Jan 1, 1975

By John D. Katsllometes

In the mining and processing industry, the maintenance plan has often evolved rather than being consciously set up resulting in an overreliance on breakdown and fixed-time maintenance (planned maintenance). Historically mining and processing plant equipment has been robust and less automated than modem equipment, making it relatively easy to work on. Mining and processing plants have relied on large and expensive maintenance departments to enable rapid attention to breakdowns. Maintenance itself can result in excessive downtime and costs. This results from the requirement to take the machinery off-line to carry out (possibly unnecessary and invasive) maintenance. The danger of infant mortality after it has been put back on line again and also the cost of the maintenance action itself contributes to costs. A goal of any well-run maintenance program is to have the lowest cost while providing 100% capacity 100% of the time to operations. When maintenance investments are at a minimum, the cost of lost production is at its highest. As maintenance effort and investments are intelligently increased, the production loss gradually decreases until the lowest combined cost is achieved. This is the maintenance goal. A road map is needed to achieving maintenance excellence. This article addresses a "Road Map" to achieving maintenance excellence. INTRODUCTION Mining and processing industry maintenance is big business. A world-class maintenance program is characterized by maintenance excellence.

Jan 1, 2004

By D. F. Boyd

On April 10, 1958 a new 7500 long ton/day iron ore beneficiation plant went on stream producing an average of 3000 long-tons of high quality concentrate a day. Plant operates on two, 12-hour shifts is six days per week, The new mill end crust ink plant were built adjacent to the company's open pit dining operate on at Bomi Hills, Liberia. The mall is essentially a gravity concentrator employing crushing, and grinding to liberate the mineral values, followed by concentration in Humphreys spirals. The cleaner spiral tailings are re-ground and tabled to recover additional iron values. Ire addition to. this mills the company operates a crushing and screening plant for the high grade direct shipping ores

Jan 1, 1962

By John W. Tieman

The increasing magnitude of our nation's pollution problems seems to stem from two main factors: urbanization and technical advance. In 1920, less than half the country's 106 million people lived in cities. Forty years later, the urban population accounted for 70 percent of the nation's 179 million. It is predicted that by the end of the century, 95 percent of the U. S. population, estimated at 280 million, will live in urban areas. As these people live increasingly in city concentrations, their residues also concentrate. With technological advances to support the increasing population, the variety and quantity of goods that we use also increases. New materials and processes result in increases in pollutants, some of them new. The harmfulness of these pollutants is sometimes known, but sometimes only suspected. One pollutant of concern at the present time is sulfur dioxide, the product of combustion of sulfur-containing fuels. Research on processes to remove sulfur oxides from flue gas has been in progress for many years. Pioneers in this field were the British who, in the early 1930's, installed a full-scale flue gas scrubbing unit on a 120 MW boiler using alkaline water from a Thames estuary plus chalk. Since that time, various methods have been studied by many investigators. Federal laws covering air pollution started with the 1955 Air Pollution Control Act. With the advent of the Air Quality Act of 1967, and subsequent publishing of criteria and available technology for control of sulfur oxides in January 1969, the clamor for information on commercially available control techniques to remove sulfur from fossil fuels has rapidly increased. Although many state-of-the-art papers have deluged the literature during the past several years, the research going on in the area of sulfur oxides control is of such importance that periodic reviews are justified. It is the purpose of this paper, therefore, to again review the state-of-the-art, but this time from the stand-point of what is immediately commercially available

Jan 1, 1972

By Theodore Feldsher, Seung Han Kim, Mourad Attalla, John Roadifer, Chu-Chieh Jay Lin

Lifelines in seismic regions of the world seldom can escape crossing active faults. Cities in California have been mitigating this risk by constructing improved fault crossings. This paper discusses the analyses and design of the lining for a tunnel carrying a water conveyance pipeline through a fault that can potentially displace during a major earthquake event. The paper presents expected fault displacement, fault width and orientation respective to the tunnel, characterization of the ground surrounding the tunnel and its interaction with the lining, and performance required of the lining. Several other fault crossings will also be presented and discussed

Dec 1, 2022

By I. E. Odom

The rare magnesium-lithium clay mineral hectorite occurs at many places in the McDermitt caldera of Nevada-Oregon. Commercial development of several high purity deposits began in 1986. The hectorite was precipitated in a lake environment formed after collapse of the McDermitt caldera. Hectorite beds and lenses are associated with volcaniclastic sediments, limestones, dolomites, zeolites and locally sandy bentonites. The high purity deposits appear to be associated with hydrothermal areas. The hectorite consists of extremely small flake-shaped crystals, and Ca is the predominant exchangeable ion. Its color ranges from white to light green. Commercial uses developed to date include high brightness magnesium aluminum silicate products, organophilic clays, pulp retention, and ceramics. The MAS is used as a suspending agent, binder, stabilizer and thixotrope in aqueous solutions for cosmetics, household cleaners, pharmaceuticals and miscellaneous industrial applications. Organoclays are used in printing inks and paints.

Jan 1, 1992

By Douglas Castleberry

The degree of fragmentation obtained in primary quarry blasting has always been a factor in the speed of digging' the muckpile This paper will discuss a case history of increased production and associated lowered costs from increased fragmentation. The quarry under discussion is fairly new, located in Georgia, and is in the large operation .category. Loading is done by three yard shovels, and, primary crushing by a 48" x 60" haw crusher preceded by a 5' wide feeder. The stone is a hard granite gneiss, of Los Angeles rating 22, and apparent specific gravity is 2.68. The product is shipped to points in that state for railroad ballast, concrete aggregate, and road building stone. Inasmuch as fairly large shovels and a large Jaw were to be utilized, initial drilling and blasting were pointed toward producing fairly large sized muck for this large equipment. This was following a concept somewhat in vogue for some years in the Southeast wherein many large equipment plants would tend towards larger fragmentation, and smaller equipped plants would conversely tend toward attempts at smaller sized rock piles for smaller shovels and crushers.

Jan 1, 1960

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

By A. Acar, E. T. Tuzcu, Y. O. Vural

"In order to sustain the operations in chromite processing plants, due to concentrate selling cost, plants are in need of optimization in terms of capacity and recovery increase. In this study, DAMA Engineering carried out a methodological study for the purpose after a detailed sampling campaign in a plant which is situated in one the main chromite zones in Turkey; 1 The current status of the plant was investigated quantitatively with the bottlenecks, Plant overall efficiency in terms of recovery, Efficiencies of the particular equipment (mill, screen, gravity circuit), 2 A new circuit was proposed with the available equipment, 3 The new circuit that is product of modeling and experimental effort, was evaluated quantitatively as if it is a running plant, After 4-5 months continuous effort, the capacity of the plant was almost doubled (37 tph to 70 tph) and the plant overall recovery was increased from 48% to 63% by grinding adjustments and additional shaking tables theoretically. It was shown that the plant may move into profit with the minimum amount investment using readily available system. INTRODUCTION TO THE CURRENT PLANT The objective of the study is to increase the capacity and recovery of the chromite plant owned by Kurmel Group, Akmetal Inc. The complete study is given elsewhere (DAMA, 2016). The plant is situated in one of the main chromite zones in Turkey; Aladag. The current capacity of the plant is around 35 tph and the overall recovery declared by plant engineer is around 47 %. The chromite plant mainly has 3 units; crushing, grinding and gravitational circuits. The crushing circuit has 3 stages; a jaw crusher, a secondary cone crusher and a tertiary cone crusher operating in closed circuit with a vibrating screen with the aperture size of 15mm. In grinding circuit, a rod mill (2.44 6m x 3.6) and a ball mill (2.13 x 2.3m) are used for primary and secondary grinding, respectively. Derrick screens are used for the size separation. Additionally, for the size classification of the system, hydrosizers are used and each size fraction is sent to the shaking table sets. The middling product of the tables is subjected to re-grinding with a ball mill with the dimensions of 2.1 x 2.9 m. The capacity and the recovery are affected by several bottle necks; hydrosizers’ pure classification, primary/secondary mill power vs capacity problems, re-grinding product’s high slime content and so on. These combined factors made the plant to run in low recovery and capacity. Hence, DAMA was asked to make a study to investigate current status of the plant and propose a new solution to increase capacity and recovery of the plant. The conceptual flowsheet of the circuit is given in Figure 1 below."

Jan 1, 2017

By Ezz El Din Abdel Hakim Khalaf, Khalid S. Essa, Marc Munschy, Mohamed A. S. Youssef

This study focused on joint interpretation of the aeromagnetic and radiometric data to allocate and describe the structural elements and mineralization zones such as uranium, gold, and sulfide in the Gebel Umm Tineidba and its surroundings, Eastern Desert, Egypt. The study region is covered by exposures of Precambrian rocks such as gneisses, migmatites, ophiolitic mélange, metavolcanics, younger granites, and Quaternary sedimentary covers. The application of the total intensity magnetic and reduced-to-pole maps, power spectrum, analytic signal, tilt-angle, and local wavenumber maps helps in recognizing magnetic sources distribution, lineament features, and mineral zones delineation. The obtained results indicate that the depths of the deeper NE–SW, NNE–SSW, and N–S trending structures extend from 400 to 1750 m and shallower ones range from 100 to 400 m. Finally, the main trends of these structures affect the probable mineralization zones.

Sep 22, 2022

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Shrinkage stope mining can be employed in steeply dipping veins where both the wall and the vein material are sufficiently strong to stand with only minimal ground support. Shrinkage stope mining takes advantage of the swell in volume produced in breaking in-place ore. This expanded volume of ore is allowed to occupy part of the mined-out vein, and in so doing provides ground sup¬port and a working surface for the miners. Only enough of the ore is drawn after each stoping cut to allow work¬ing room. Not until the entire mining block has been broken is the full amount of broken ore drawn from the stope. DEVELOPMENT PRACTICES FOR SHRINKAGE STOPING The vein is developed into stoping blocks, each of which is 76 to 91 m (250 to 300 ft) in length and 61 m (200 ft) between levels. Level development, described later, is either on the vein or parallel to it with crosscuts periodically driven over to the vein. There are usually two exits from each stope. The first entry is a raise at one end driven either conventionally by raise climber, or by a raised borehole. Present practice is that this raise, put in from level to level, is either a 2.1- x 2.1-m (7- x 7-ft) Alimak raise or a 1.2- to 1.8-m (4- to 6-ft) diam borehole. Either raise system will require pro¬visions for an ore chute carried with the stope to the haulage level or the scram drift. At 9- to 12-m (30- to 40-ft) vertical intervals, dogholes are developed from the raise so that when stoping breaks back into these dogholes, timber or steel sets and necessary service facilities can be installed. The second entry to the stope may be either a similar raise at the stope endline, or more economically, a cribbed raise carried with the stope. As previously stated, development of the ore block is achieved by either drifting on the vein or by paralleling the vein with a footwall lateral and then crosscutting over to the vein at specified intervals. In the following discussion, three basic cases are illustrated in Figs. 1, 2, and 3. In Fig. 1, development is in the footwall by a 3- x 3-m (10- x 10-ft) trackless lateral. A heading is also driven on the ore and taken either full width or driven a standard size and slabbed to the vein width. Approxi¬mately 9-m (30-ft) long crosscuts on 7.6-m (25-ft) cen¬ters are driven from the lateral to the vein. For ease in muck handling they are usually put in on a slant rather than at right angles. A single orepass, located off the lateral and in the center of one stope block, can serve not only that stope, but also one on either side, up to a tramming distance of not more than 137 m (450 ft). Raises are put at the stope endlines on 91-m (300-ft) centers. The back of the vein is shot down and just enough broken material is drawn off to permit access for men to work off the broken ore. Development in Fig. 2 progresses by driving a 3- x 3-m (10- x 10-ft) trackless heading on the footwall side of the vein. The ore block is delineated by raises on 91-m (300-ft) centers. Crosscuts are again driven on 7.6-m (25-ft) centers over to the vein. Approximately four rounds are then taken up to the vein and each round is successively belled out so that all the crosscuts (pockets, in this case) connect. In this development, as opposed to that in Fig. 1 where there were no belled

Jan 1, 1982

By Emily Sing, Ashim Gajurel, Thomas Pennington, William Brown

The Pardee Chemical Feed Shaft Project involves construction of two new chemical feed shafts to improve raw water treatment capabilities at the East Bay Municipal Utility District’s (EBMUD) Pardee Reservoir in Valley Springs, California. The project includes construction of two 250-foot deep, 16-inch diameter stainless steel chemical feed shafts that penetrate an existing 8-foot diameter concrete lined conveyance tunnel. The design approach required the shafts be installed using top-down drilling methods and within a strict verticality tolerance (0.1%). Innovative precision drilling techniques ensured that the shafts penetrated the tunnel in their planned locations and the installed chemical feed lines would function as designed. Challenges included extremely limited access to the tunnel because of a requirement to maintain the tunnel in service during construction. This paper discusses the overall project’s design and construction approach, including unanticipated conditions that the project team faced and how these conditions were managed and overcome through collaboration between the contractor, designer, and owner.

Dec 1, 2022

By L. S. Gertsch, M. Z. Abu Bakar

Linear cutting tests of a porous sandstone with a radial drag pick show that saturation of rock with water can increase the specific energy of fragmentation. This appears to be due, in this case, to a saturation-induced increase in the forces acting on the cutting tool without a concomitant increase of the fragmented volume. The mechanisms of this reaction are explored by examining various responses of the parameters controlled and induced during the linear cutting tests, such as cut spacing, cutter penetration, three-dimensional forces and muck production. A program of load-indentation testing is underway to evaluate the permeability threshold of this behavior. These findings are opposite from those made when the same rock is cut with a constant cross-section disc cutter reported elsewhere (Abu Bakar and Gertsch, 2011). Such results highlight the effects of different cutting tool designs, and indicate the need for a well-coordinated program of research to support effective excavator design and selection.

Jan 1, 2012

By D. L. Romero

The Line Creek Mine is operated by Crows Nest Resources Limited, a wholly owned subsidiary of Shell Canada Resources Limited. It is located approximately 25 km north of Sparwood in southeast British Columbia (refer to figure 1). The Line Creek coal deposit is part of the Upper Elk Coalfield in the East Kootenays. The coal is a medium volatile, low sulfur, bituminous coal and is used as a coking coal. Coal close to the outcrop is typically of low F.S.I. and is processed for thermal use. The present pits have a total coal reserve of 30 million clean tonnes and is a multi-bench, open-pit operation. The coal is recovered by front shovel and backhoe combination, and hauled to the plant with a fleet of 120-tonne and 40-tonne capacity trucks. Line Creek is unique in that it can simultaneously treat both metallurgical and thermal coal in separate processing facilities (refer to figure 2). Run-of-mine coal is delivered to the truck dump. The plus 50 mm material is scalped off and reduced to minus 50 mm in two rotary breakers. The raw coal is then conveyed to one of five, 5000-tonne capacity, silos. Typically one silo is used for thermal coal and four for metallurgical coal (refer to figure 3).

Jan 1, 1991

By J. J. DeMull, B. A. Boster

Amax's Sleeper mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 t/d (500 stpd) to more than 720 t/d (795 stpd). Heap leaching was added to the process facilities in September 1986 at a design rate of 1.5 kt/d (1650 stpd) and current heap leaching rates exceed 2.7 kt/d (2950 stpd). Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1990

By Marshall D. Himes, Erich U. Petersen

The Sheep Creek deposit near White Sulfur Springs, Montana, is a middle Proterozoic stratabound and strataform sediment- hosted massive sulfide containing 4.5 million tonnes (5.0 million tons) averaging 2.5% copper, and 0.1% cobalt in the upper sulfide zone (USZ) and 1.8 million tonnes (2.0 million tons) averaging 6% copper in the lower sulfide zone (LSZ). Mineralization is hosted in lower Newland shales and debris flow conglomerates in the graben controlled Helena Embayment of the Belt Basin. USZ mineralization is characteristically high in Cu, Co, Ni, Ba, As, Pb, and Ag. Mineralogically it consists of barite, pyrite, chalcopyrite, and tennantite with minor amounts of marcasite and various cobalt minerals. By contrast, the LSZ is higher in Cu, Ni, and Au and lower in Co, As, Pb, and Ag. Mineralogy of the LSZ consists of dolomite, pyrite, and chalcopyrite. In both zones significant amounts of cobalt, nickel, arsenic and copper are incorporated in pyrite rims. Tennantite controls the abundance of numerous trace elements in the ores. Fluid incluison data from hydrothermal USZ barite suggests that mineralization took place at temperatures in excess of 250°C, under relatively oxidizing conditions (f02 = 10-32+1) from moderately saline (1.1-3.5m), metal rich brines. The absence of barite in the LSZ suggests mineralization under more reduced conditions (f02 = 10.38+2). Mineralization was initiated following basin subsidence in excess of 400m. Contemporaneous with movement along a growth fault(s) was upward migration of hot metal-bearing fluids which permeated the loosely consolidated sediments and may have vented on the sea floor. The differences in the two zones may be explained by the effects of variations in local basin morphology and solution chemistry.

Jan 1, 1990

By D. C. Edwards

In an age where customer service and quality drive today's industry and business, no service or product is exempt from these demands. Industry and business are streamlining everything from people to equipment and today have a heavier reliance on the performance and quality of their assets and equipment, (one of the keys to staying competitive). In the mining process industry, the centrifugal slurry pump is a key piece of equipment that keeps product moving and aids in generating revenue for its owner. The continued improvement and customer success lies in a team effort between the mining industry and the pump manufacturers. We, the pump manufacturers, need to keep improving our designs to further extend the life of our pump with fewer failures and promote to our customers proper maintenance of the pumps to continually keep unexpected failures to a minimum. Strict equipment maintenance, as thoroughly demonstrated by the military, is key to the long life and success of any piece of equipment. In the often harsh duty of the centrifugal slurry pump, maintenance is something that requires "attention to detail". No area of the pump is exempt from attentive maintenance. Here, discussions will focus on the areas of the mechanical drive end, wet end, seals, and extended pump shut down and start up. There has not been a slurry pump designed to maintain or repair itself. So in effect, each pump warrants able bodied maintenance persons to maintain them who continually observe all the rules of safety. Prior to any maintenance discussion or action, the issue of safety should always be addressed. Here, as with everywhere, the same rules apply. Work at a safe pace, note all safety precautions, use associated safety equipment and personal protective attire, observe all tagout and lockout procedures, and most importantly, be aware.

Jan 1, 1996