Search Documents

By D. Malhotra

Metallurgists are continuously striving to improve recovery. But optimization of profits and/or revenue dictates that recovery can be sacrificed at the expense of throughput. However, recently there has been significant interest in the concept of retreatment of tailings to enhance recovery and hence revenue while maintaining high throughput. The authors discuss the technical and economic factors that need to be considered in evaluation of the feasibility of retreatment of tailings including the potential feed streams (i.e., rougher tailings, cleaner tailings, etc.) and processing options (i.e., physical beneficiation, chemical processing, etc.). A case study for base metals is discussed.

Jan 1, 1994

By M. Soderstrom

In a solvent extraction (SX) plant, stage efficiency calculations are used to determine mixer efficiency. With modern extractants and mixing equipment, it is generally taken for granted that stage efficiencies will be above 95%, but this is not always the case. Dependant on mixer/solution conditions, stage efficiencies can occasionally be low, therefore leading to higher reagent usage. Proper methods to identify when stage efficiency performance is below expectations, and ways to identify if it is an equipment or chemical issue are valuable tools for a plant metallurgist. With these tools and skills an on-site metallurgist can more quickly return their SX plant to proper operation. This paper will discuss methods for analyzing stage efficiency, evaluating factors that may affect stage efficiency, and evaluating the impact of stage efficiency on the overall operation.

Jan 1, 2010

By K. H. McDaniel, D. M. Loring

The underground ventilation system at the Waste Isolation Pilot Plant (WIPP) provides for the unparalleled ability to ensure the safety of the workers, the public and the environment. Although small spatially, the system can vary the airflow from 31.2 to 217.1 m3/s (66,000 to 460,000 cfm). The system can automatically incorporate HEPA filtration in the event of radioactive contamination. Remote-capable regulators individually control the four main splits, and they can be adjusted from the surface if necessary. A ventilation remote-monitoring and control system provides real-time information. Future areas of concern include DPM compliance, system psychrometry, logic-based real-time mine-ventilation simulation and automation using PLC technology. This paper discusses the evolution of this system.

Jan 1, 2003

By J. M. Van Langen

In 1965 Hoogovens was looking for additional capacity for burden preparation in the order of 2,5 to 3 million metric tons per annum of some kind of optimal blast furnace ore feed. In principle four solutions offered them-selves for further investigation: 1. purchase of screened ore and/or run of mine ores with the provision of a corresponding ore screening capacity on the blast furnace site; 2. manufacture of sinter; 3. purchase of pellets; 4. manufacture of pellets. After studying the technological, technical, economical and commercial factors Hoogovens decided for the last mentioned possibility. Before taking this decision not only a great number of different mixtures of iron ore were tested, but during a long period in one of the big blast furnaces a number of tests were also executed with purchased pellets from South and North America. It was found, that using 50% acid pellets with 40% basic sinter a coke rate saving of 25 kg per ton hot metal (50 lbs/net THM) and a production gain of 15% could be obtained as compared with a full sinter practice. With some pellets it became clear, that due to properties, commonly referred to as swelling, we got very poor furnace performances; so in studying the production of pellets, pellet quality should be regarded as the most important aspect of the problem.

Jan 1, 1972

By H. L. Holden

The single line grinding circuit at Bond Gold's Colosseum mine consists of variable speed drive semi-autogenous (SAG) milling and secondary grinding with a fixed speed ball mill. There are several advantages and disadvantages of operating SAG mills with variable speed drives. Discussion in this paper will focus on the effects of variable speed SAG milling in relation to mill liner wear, grinding media consumption, and mill operating availability. Operating experiences, corresponding mill data, and pertinent design changes are also presented.

Jan 1, 1991

By D. D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a cost-effective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Feb 23, 2014

By J. E. Murphy, L. A. Walters, F. H. Nehl, G. B. Atkinson

The US Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A h/150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 msecs. Graphite, lead and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70°C (158° F) gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10% to 30%, and a period of 100 msecs to 1000 msecs gave the following results: Ag concentrations decreased from 34 µg/mL to 0.1 µg/mL. Au concentrations decreased from 54 µg/mL to 0.2 µg/mL and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 1995

By K. Johnson, B. Schiffer

Demonstrating aquifer restoration is an essential component of regulatory approval needed to mine uranium, copper, and other minerals by in-situ recovery (ISR). A PHREEQC geochemical model provided a useful means of forecasting the time for restoration and predicting future groundwater quality following low pH mining at Strata Energy’s Ross ISR Project in northeast Wyoming. The model simulated groundwater quality at three phases of the process: at the end of mining; during restoration; and post- restoration. The model utilized the one-dimensional reactive transport and dual porosity features of PHREEQC. Mineral surface ion-exchange, dissolution/precipitation reactions, and adsorption processes were simulated to estimate water quality as the pH was shifted from circumneutral to acidic during mining and back to neutral during restoration. The model results showed that cost-effective management of mine water could meet regulatory requirements. Additionally, the model was used to interpret results from a field trial and inform operational decisions. The predictive approach and geochemical understanding developed have application in assessing aquifer restoration for other ISR projects.

Mar 2, 2022

By Manchao He, Xiaoding Xu, Yubing Gao

Based on the geological conditions of the 15,600 working face in Pingba Mine, this paper establishes the mechanical model of the stress distribution in the pre-working face under the influence of mining pressure based on a hemispherical stress distribution theory. The analytical formula for the stress distribution is determined. A numerical model for the mining pressure under the influence of key layer is also constructed, and dynamic stress interruptions under various roof-cutting relief schemes in different horizontal positions are simulated. The stress distribution of the stope under different pressure relief schemes is analyzed and compared with the theoretical results. Results show that blasting roof cutting blocks the transmission of the abutment pressure to the working surface to the coal and rock mass in front of the working face, reducing the significant working face mining pressure influence range, which decreases as blasting pressure relief position moves toward the working face. Stress accumulation in the coal in front of the working face also increases as the blasting pressure relief position moves toward the working surface. Engineering practice results show that blasting cutting can effectively block the propagation of mining pressure, and the stress impact range is shortened by approximately 1/3.

Jul 31, 2021

By J. T. YIi-Penttiia

Dust formation and reaction mechanisms of copper matte particles were investigated in simulated flash oxidation conditions. The granulated and ground matte consisted of 72 wt% Cu, 4 wt% Fe and 21 wt% S. Experiments were conducted by using a laminar-flow furnace with a reaction gas composition ranging from 20 vol% to 75 vol% O2 in nitrogen. The particle feeding was carried out by the single-particle method and samples were quenched after a specified reaction time (approximately 0.05-004 s) in a cold water film. Experimental temperatures were between 800 and 1300°C. Chemical analysis was used to determine oxidation degree, and an optical and scanning electron microscope combined with energy dispersive analysis was used for characterization of the reacted particles.

Jan 1, 1998

By L. Zhou, L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly; however, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics, namely size and location, are of great importance in reducing the risk of mine fire injuries. A new improved fire location algorithm has been developed and integrated into an Atmospheric Monitoring System (AMS) program by researchers from the National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.

Sep 29, 2020

By Guy Bridges, Elton Ko, Cheng Ting Ning, Owen Ng, Giovanni Chang, Robert Anderson

"PROJECT OVERVIEWThe Liantang/Heung Yuen Wai Boundary Control Point (BCP) and Associated Works will be the seventhland crossing between Shenzhen and the Hong Kong Special Administrative Region (HKSAR) of China.The project includes site formation of about 23 hectares of land for the development of the BCP and anapproximately 11-kilometre (km) long dual two-lane trunk road (the “Connecting Road”), connecting theBCP with the existing Fanling Highway. The route alignment is within a relatively rural area of HongKong, with very limited similar infrastructure works carried out nearby. It passes beneath bothmountainous terrain, and alluvial plains, and falls within an area of several major regional faults andassociated metamorphism, resulting in a complex variety of ground conditions.ALIGNMENTThe Civil Engineering and Development Department of the Government of the Hong Kong SpecialAdministrative Region carried out extensive public engagement in selecting the alignment of theConnecting Road. Over 70 consultation forums with public bodies, including the District Councils, RuralCommittees, local representatives, etc. were held during the alignment design process. In order toalleviate the concerns of various nearby villages, and to minimize land clearance and environmentalproblems, the original alignment of 10 km long (3.5 km of tunnels and 6.5 km of viaducts) was revised toits final alignment of 11 km long which comprises 5.7 km of tunnels, 4.3 km of viaducts and 1.0 km of atgrade roads.The finally adopted alignment commences at the southern end with an interchange with the existingFanling Highway, part of Route 9, which is a dual three lane expressway currently being widened to dual4 lane. Alongside the expressway is the main rail connection to the mainland of China, and theinterchange viaducts connecting to the southern portal of the Lung Shan tunnel must cross over thisrailway. The southern portal is located in the foothills of Lung Shan, and the 4.8km long tunnel is alignedin a north-northeasterly direction. The southern half passes under mountainous terrain of Lung Shan,and then crosses a valley containing the Kwan Tei river. The northern section comprises low hillsseparated by an alluvial plain and Tan Chuk Hang village area. At the northern end, the tunnel turns tothe north-west to connect with Sha Tau Kok road, an existing single carriageway road, with a newroundabout interchange. Mid-way along this tunnel there will be a ventilation building, connected to the main tunnel by a 330m long ventilation adit. To the north-western side of this interchange is the900m long Cheung Shan tunnel, and after this the remaining 4.3km of the highway connecting with theBoundary Control Point is to be constructed as an elevated viaduct. The alignment is shown in Figure 1."

Jan 1, 2016

By A. B. Cecala

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U.S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1993

By Jogeshwara Sahu, Sapan Kumar Kandi, SANDEEP KUMAR JENA, Sachida Nanda Sahu, Sarada Prasad Das

The present article reports the recovery of potassium from mica scrap using carbide lime waste and NaCl. The acid leaching of mica [4 M H2SO4 at 90 °C] can recover a maximum of 25% potassium. However, in the chlorination roasting (with CLW and NaCl) water leaching process, it was possible to recover potassium to the tune of 94% [900 °C, 50 min roasting; mica:CLW:NaCl 1:0.75:1]. The formation of water-soluble phase like sylvite (KCl) and water-insoluble phases like anorthite ( CaAl2Si2O8) and nepheline ( NaAlSiO4) confirms the complete breakdown of the mica crystal structure. The extraction mechanism proceeds with the formation of a transition state followed by the release of potassium as KCl. The characterisation studies using ICP-OES, XRD, FTIR and FESEM support the proposed extraction mechanism. The salt produced by the evaporation of roast-leached liquor confirms the presence of sylvite and halite only, which can be separated to get the fertiliser grade KCl.

Sep 29, 2021

By Charles M. Hauptman

The Karst asbestos deposit, discovered seventy years ago, is 32 miles south of Bozeman in southwestern Montana. The deposit is about one-half mile west of the Gallatin River which flows in a deep V-shaped valley flanked on either side by rugged mountains. The Madison range is west of the river and the Gallatin range lies to the east. A busy all-weather highway, U.S. No. 191, follows the river and is the major north-south route between Bozeman and the Gallatin valley to the north and Idaho and the west entrance of Yellowstone National Park to the south. The asbestos deposit is a large body of serpentinized peridotite in which anthophy11ite.occurs, both as distinct veins and as a disseminated mineral in the peridotite mass. The known exposures of the asbestos-bearing rock occur on a steen south slope at an "elevation of about 7000 feet, an elevation 'which is about 1200 feet above the Gallatin River. Over the years, a number of small companies have attempted to exploit the Karst asbestos deposit without continuing success. The present operator, Galaxy Mining Corporation, has attempted a systematic approach to the problem by utilizing geologic and engineering surveys to determine the economic and technical feasibility of a mine and plant to produce a finished asbestos pro-duct. The results of this work indicate a high probability of success for the project. However the company now faces that dilel1lJllB so common to the non-metallic mineral business; that is, whether to continue a research program of further mineralogical and technological studies in conjunction with detailed market surveys or to rely on the work done to date and embark on a pilot progril1n

Jan 1, 1971

By R. D. Williams

INTRODUCTION In a very real sense, Butte, Montana is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site. One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot Smelter operated from 1881 to 1910 moving Upper Silver Bow Creek to the south and depositing approximately 370,000 cubic yards of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot Tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 224,000 cubic yards of contaminated material. As part of the Superfund remedy, EPA proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place which set the stage for a series of studies which continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. HISTORY OF THE PARROTT MINE AND TAILINGS Placer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery lead to a stampede of placer and lode claims. One of the first lode claims located was the “Parrot” lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow and it wasn’t until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine! The Parrott mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the District’s rich copper ore. In 1885 the employees of the Parrot Smelter bought the Butte Reduction Works, another smelter. In 1885 dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Figure 1).

Jan 1, 2019

By J. Herhold, S. Plaum

"Increasing worldwide energy demands, coupled with desires for cleaner energy, have led to greater research of renewable energies. Strongly weather-dependent energy sources, e.g. solar and wind energy, are unable to provide a constant control energy to withstand the fluctuation of the extensive power systems during peak hours. The pump storage plant Nant de Drance in Switzerland will not only have the capacity of a nuclear power plant, producing 900 MW, but will also combine the environmental aspect and the demand for controlled energy. Nant de Drance is one of the pioneer projects for upcoming energy challenges and serves as a model for future pump storage plants. This paper focuses on the planning process and the project execution of interdisciplinary large-scale projects such as Nant de Drance, including project related data handling, communication systems and project handling skills. Furthermore, the paper discusses mining excavation in the context of large scale projects and their regional environmental challenges, e.g. high alpine rock mass on the site of Nant de Drance. PROJECT BACKGROUND Project Overview Nant de Drance is a 900 MW pump storage plant located in the Swiss Alps. To provide such a high energy storage, six turbines (reversible Francis type), each with a capacity of 150 MW, were installed. Due to the efficiency factor of 80% the pump storage plant is able to provide an energy production of 2500 GWh per annum. Construction of the pump storage plant, which has been selected as “Major Tunneling Project of the Year” in 2014 by NCE and ITA-AITES, will be completed over 10 years. Therefore, the project has been divided in six major phases outlined below: - Launch: 2008 - Access Gallery: 2010 – 2012 - Excavation KMA, KTR: 2011 – 2014 - Concreting KMA, KTR: 2014 – 2016 - Installation of HEM equipment: 2014 – 2018 - Tests & entry into service: 2017 – 2018 Figure 1 outlines the single process phases of the project. For the construction of the shafts, galleries and caverns, 1.7 million m³ of metamorphic rock with sedimentary origin (mica schist & paragneiss of the massif „Aiguilles Rouges“) were excavated. A tunnel network with a total length of 15 km was created. The machine cavern measures 194 m long, 32 m wide and 52 m tall."

Jan 1, 2016

By P. A. Lindberg

Early Proterozoic ore deposits in the Verde district at Jerome, Arizona have produced 33.7 million metric tons of ore (1893-1975). The United Verde and United Verde Extension deposits produced most of the ore that yielded 1,644,323,100 kg Cu plus large amounts of Au, Ag, and Zn. These deposits are situated on the fractured and hydrothermally altered apex of a large submarine rhyolitic extrusive (Cleopatra formation). Precambrian lithologies are penetratively deformed and at Jerome the Fl folds plunge steep to the NNW. For the past two decades the volcanogenic model has superseded the replacement theory of ore formation.

Jan 1, 1992

By T. Shumka, M. J. Druckenmiller

"INTRODUCTION As we push further into the 21st century and closer to a more efficient mine, safety and operational enhancements are the two major keys towards attaining success. The Crusher Vision Automation System (CVAS) is a technological advance that will allow an operator to achieve higher safety and higher operational goals in the same piece of equipment. The CVAS is a patent pending system and method for measuring and maintaining the closed side setting (CSS) on gyratory crushers. In the same equipment and technology package, the CVAS will also allow safer placement of main shaft pieces for maintenance and replacement. This technology yields multiple uses and allows a site to significantly enhance safety and operational efficiencies. This measurement technique is used to provide more accurate data and faster data collection times than current techniques used today. It will give crusher operators accurate and reliable measurement for the CSS in a live, operating environment. Measurement data can be collected in five minutes allowing for fast adjustment of the mantle position and subsequent enhancement and streamlining of a crusher and downstream flowsheet. The advantage of this system is that it is permanently mounted at the crusher location, where the operator can turn the system on and off as many times as they like throughout the day with a goal of maintaining a constant CSS gap based on production and maintenance criteria to help streamline operations and enhance safety efficiencies.Regarding its other main functional area, mainshaft maintenance, it allows this work to be performed remotely while keeping personnel safer and out of harm’s way. SAFETY ENHANCEMENT The safety factor enhancement with this system is extreme. It does not require the use of overhead cranes, cleaning out the crusher, lowering people into the crusher or having the operator lower paint cans or lead balls into the crusher pocket while the crusher is in operation for measuring the setting. In order to perform the CSS measurements, the operator only needs to operate the laser through manipulation of a joystick while watching the video feed. Danger of a person falling into the crusher while trying to take measures is eliminated, as are the effects of handling lead balls and tracer dyes."

Jan 1, 2015

By H. Sahay

The current Canadian coal production is approximately 57x106 tonnes per annum of which some 25 million tonnes is exported. Two thirds of the Canadian output is classified as thermal and one third as coking or metallurgical coal. The Canadian coal industry, like the industries in some other industrialized nations, has gone through a cycle of ups and downs. The current world vide recession and stable oil prices have somewhat dampened the plans for a further growth of this industry - albeit temporarily. No new mines are expected to be developed within the next few years. However the production is projected to increase to 60x106 tonnes in 1985 increasing to an estimated 75 to 80x106 tonnes by 1995. The Canadian mines are highly mechanized and are willing to employ the modern technology to maintain its competitive position in the world's coal market. This paper reviews the recent technical developments which continue to improve resource recovery and productivity.

Jan 1, 1986