Search Documents

By Baojie Zhang

The main goal of this study was not only to investigate the effectiveness of the FGX Dry Separator for removing pure rock from run-of-mine coal producing a better feed stock for conventional coal preparation plants but also to optimize the FGX Dry Separator performance for producing a salable clean coal product without using the conventional wet coal preparation processes. A Model FGX-1 Dry Separator with feed throughput capacity of 10 tph was extensively tested at the Illinois Coal Development Park using two coal samples having distinctly different cleaning characteristics. Statistically designed experimental programs were conducted to indentify critical process variables and optimize FGX Dry Separator performance by systematic adjustments of critical process variable parameters. The coal cleaning performance of the FGX Dry Separator was evaluated for the particle size range of 63.5 x 4.76 mm in most cases, although FGX Dry Separator feed consisted of nominal -63.5 mm run-of-mine coals. The best cleaning performance obtained from the FGX Dry Separator is described by specific gravity of separation (SG50) and probable error (Ep) values of 1.98 and 0.17, respectively. The SG50 and Ep values for individual size fractions were as follow: 1.90 and 0.12 for the +50.8 mm size fraction, 1.95 and 0.18 for the 50.8 x 25.4 mm size fraction, 2.01 and 0.19 for the 25.4 x 12.7 mm size fraction, and 2.03 and 0.23 for the 12.7 x 4.76 mm size fraction. These process efficiency measures produced a clean coal with ash content of 13.38% from a feed coal with ash content of 34.45%. Ash content of tailings and middlings streams were 85.09% and 39.57%, respectively. Total sulfur contents of corresponding streams were 3.87%, 4.68%, 6.87%, and 4.62%. For a relatively easy to clean Illinois No 6 seam coal (Cleaning Index: 0.72), only about 0.42% of the clean coal (i.e., 1.6 float fraction) present in the feed was lost to the tailings stream. For a relatively difficult to clean coal (Cleaning Index: 0.53), about 0.98% of the clean coal present in the feed was lost to the tailings stream.

Jan 1, 2012

By Richard J. Lewandowski

Corrosion and product contamination have been difficult problems for extractive metallurgy industries in the U.S. because of the highly active chemicals used. During the past twelve years, other industries, particularly the chemical and paper segments, began to combat this problem with some degree of success using newer materials of construction, including reinforced plastics. These materials are made by combining a corrosion resistant thermosetting resin with a glass fiber reinforcing material and are used to con¬struct hoods, stacks, blowers, tanks, towers, pipe, and equipment of the most complex configurations. For service in contact with aggressive chemicals, the equipment is most often fabricated with the bisphenol-A fumarate polyester resins because of their resistance to corrosive attack. Data from both laboratory work and case histories of field applications are presented-for many common chemicals found in extractive processes. Information is also presented concerning design standards and recommended construction procedures

Jan 1, 1970

By W. C. Brice

Minnesota contains a major copper-nickel resource. In anticipation of requests by industry to develop this resource, the Minnesota Department Of Natural Resources has developed a computerized resource inventory and analysis system, MINESITE This extensive database is available to regulatory agencies as they evaluate mining proposals as required by law. The Resource Analysis phase of the project allows state mining policy decisions to be evaluated in terms of long-range effects on Minnesota's mining industry and environmental and land use impacts. The analysis also allows for comparison of proposed mine facility sites to a representative range of sites in terms of engineering, site characteristics, and land use and environmental impacts.

Jan 1, 1980

By Ralph H. Light

The recent surge in demand for uranium in the United States, accompanied by a significant increase in price, has resulted in exploration, mining, and milling of lower grade ores than have been exploited in the past. To sustain production levels of uranium with lower grades of feed requires larger tonnage mill operations. Also, because of recent environmental regulations, mill operations must be prepared to properly contain large tonnages of tailings, and recycle, treat and discharge, or evaporate mill effluents. Thus, the advent of lower grade ores, larger tonnage mills, and environmental considerations has made the cost of milling a critical factor in today's uranium production economics in the United States. Three basic milling methods are employed for extracting uranium from ores: 1. Acid leach, countercurrent decantation, and solvent extraction. 2. Acid leach, resin-in-pulp, and Eluex. 3. Alkaline leach, solid-liquor separation, and precipitation. Vanadium often occurs as a valuable by-product in ore deposits located in the Uravan mineral belt in Western Colorado. Also, lesser amounts of vanadium may occur in ores from South Dakota, New Mexico, and Utah. Vanadium is usually extracted in the acid leach solution with uranium and recovered by solvent extraction after recovery of the uranium. By-product recovery of uranium from phosphoric acid and porphyry copper dump leach solutions is now receiving considerable attention. Pilot plant studies are under way and construction of commercial plants is in progress.

Jan 1, 1977

By D. Collins, J. Winfield, V. Gangrade, B. Slaker, S. Braganza

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the unique pillar stability issues associated with room-and-pillar mining in dipping underground stone mines. The objective of this paper is to study the post-blast impact in and around a pillar, using microseismic monitoring. To accomplish this, a microseismic monitoring system has been installed at a dipping underground stone mine in central Pennsylvania. The microseismic system is comprised of 18 uniaxial accelerometers; 12 sensors are installed in a single pillar and 6 sensors are installed in the surrounding area. More than 4,400 microseismic events have been located near the study pillar following the blasts. The number of triggers increased significantly following the blast, and the trigger rate in the first five minutes was 60 triggers per minute and three triggers per minute over the next three hours. The processing of high-quality triggers indicated a large number of low magnitude microseismic events near the blasting face. The event locations were identified more accurately by using a 3D-velocity model, with an average 9 m expected location accuracy for this array calculated using the system data. Seismicity was absent from the core of the pillar, but significant numbers of events were found following cutter roof along a crosscut as it was developed as well as in the location of a rib failure event. Additionally, the events were located in the roof, showing high number of microseismic events within 0–10 m of the roof line compared to 10–30 m above the roof line.INTRODUCTIONGround control stability is essential to any mining operation for ensuring mineworker safety and health and preventing catastrophic failures of underground structures. The National Institute for Occupational Safety and Health (NIOSH) has conducted research in stone pillar design and has established fundamental pillar design guidelines for the underground stone industry, which resulted in the development of the S-Pillar program (Esterhuizen et al., 2011; Esterhuizen and Murphy, 2018). However, the data that makes up the S-Pillar database consists of shallow depth, flat-lying, single-level mining operations. Therefore, to expand this dataset and to develop guidelines for challenging conditions such as dipping and multi-level mines, NIOSH is currently conducting detailed pillar response investigations at mines with these characteristics. The study is being conducted using multiple research approaches, including seismic modeling and tomography, numerical modeling (Sears et al., 2019), stress monitoring, and LiDAR-based laser scanning (Slaker, Murphy, and Winfield, 2019). This paper discusses the findings from the microseismic monitoring system installed at the Pleasant Gap Mine, a steeply dipping underground limestone mine in central Pennsylvania."

Jan 1, 2019

By Hiroyuki Abé

This paper is a review of research and development on geothermal energy extraction in Japan especially on hydraulic fracturing. First recent geothermal developments in Japan are outlined in Part I. An increase in the production rate of geothermal wells may be highly dependent on the geothermal well stimulation technology based on hydraulic fracturing. The hydraulic fracturing technique must be developed also for geothermal energy to be extracted from hot, dry rock masses. In Part II, the research on hydraulic fracturing and field application are reviewed.

Jan 1, 1982

By Dale A. Shay, Roy R. Cellan

The Santa Fe Mine, located in west central Nevada, began leaching ore in 1988 and completed ore processing in 1995. Homestake Mining Company has completed final reclamation of the site, including remediation of bare surface soils resulting from the oxidation of sulfide minerals and migration of acidity in the mine waste repositories. The need to remediate oxidized sulfides and mitigate resultant acidity at the Santa Fe Mine emphasizes the economic, reclamation, and environmental advantages for understanding and pre-planning for management of potential sulfide wastes during mine planning phases. The lack of pre-planning by mining companies for sulfide waste management was common in the 1980's due primarily to mining of reserves characterized largely as oxide deposits and to the common opinion that low moisture regimes in arid or semi- arid climates would not allow for significant acid generation. Since the 1980's, operational experience has shown that sulfide wastes, deposited randomly in waste dumps and without adequate planning for final reclamation success, can create final reclamation problems that are very costly to remediate. While mine waste characterization, waste management plan compilation, and in-pit selective waste handling procedures add operational costs, the reclamation experiences at the Santa Fe Mine are indicative that pre-planning and management is worthwhile both in actual overall cost efficiency and in successful reclamation of the mine site. The reclamation program at the Santa Fe Mine shows Homestake's continued commitment to the successful management and reclamation of their mine sites.

Jan 1, 2000

By Ken Wangerud

The benefits of historic mining to this country have been many, but have come at a cost to the environment that has only begun to be understood over the past twenty years. While estimates vary, it is generally recognized that there are over 200,000 inactive and abandoned hardrock mines, with most of them located in the western U.S. Only a fraction of them are believed to be sources of metal releases with significant adverse environmental effects to the watersheds and receiving streams. State water-quality and natural resource management agencies have noted that hundreds of miles of streams are metal-impacted, and the aggregate effects of these sites within watersheds and drainage basins is poorly understood. Resources for the environmental assessment of abandoned mine land (AML) sites and watersheds have been and continue to be limited. Few hardrock mining states receive substantial reclamation funds under the (coal) Surface Mining Control and Reclamation Act. EPA Region VIII (EPA8) has an estimated 90,000 abandoned mining, milling and smelter sites, mainly in Colorado, Montana, South Dakota, Utah and Wyoming. An estimated 13,000 of the sites may have metal releases causing Clean Water Act and CERCLA non-compliance. Results of inventories by states and federal land managing agencies, indicate it is plausible that only 3,000-4,000 of these sites may be causing significant environmental degradation.

Jan 1, 1999

By John F. Slonaker

This report is a review of current research being conducted in the United States which is intended to increase the utilization of coal ash. In order that this report be as timely as possible, the majority of information was obtained by direct comunication with the people listed in the references. Due to the magnitude of the flyash research program, some projects may be inadvertently omitted. Field research on flyash for use as an agricultural fertilizer is being monitored at Virginia Polytechnic Institute and State University.1 This research is directed at determining the plant nutrients that are available in flyash as well as the quantities of flyash that can be applied to agricultural soil without adversely affecting plant growth, Coal mine spoil and refuse bank reclamation with power plant flyash is being demonstrated by United States Bureau of Mines, Morgantown, West Virginia.2 Numerous highly visible coal refuse piles and strip mine spoil banks contribute to air, water, and land environmental problems. Revegetation of several experimental sites with flyash from bituminous coal-fired power plants was undertaken in West Virginia and Pennsylvania. Conventional farm equipment was used at some of the sites while large earthmovers were required at others. The flyash served as a neutralizing agent, dilutent, and soil amendment to provide some nutrients which enhanced vegetation of the barren areas, Estimated cost of reclamation by this method is $300.00 per acre of previously leveled area. This figure can vary considerably depending upon the topography of the site, haul distance, quality of the soil and quality of flyash.

Jan 1, 1974

By Gino Vogt

In mechanized tunnelling operations performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequate/ suboptimally dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water and polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole job. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer´s point of view.

Jun 13, 2021

By D. Zim

Mining activity in South America is a growing enterprise. One of difficulties found in many areas of the South American continent, especially in north Chile and south Peru, is the shortage of water supply. In order to overcome this difficulty some mining companies proposed to transport the water from Pacific Ocean up to the mountains. This can be accomplished by the use of stainless steel pipelines, but this is a cost prohibitive solution and is also subject to severe pitting corrosion in a saline environment. The use of mild steel may be a lower cost solution than stainless steel as the material of construction for pipelines but it is subject to corrosion anyway. The corrosion in this case can be internal or external corrosion although cathodic protection as well preventive maintenance usually is enough to mitigate external corrosion without the need to shut down the pipeline. The same is not true about the prevention of internal corrosion. It is not practical, sometimes not even possible, shutdown a pipeline to carry out an inspection and fix sections where potential failures are detected. It is possible avoid corrosion caused by sea water within the mild steel pipelines by applying a proper chemical program designed to virtually eliminate dissolved oxygen in the water commonly called deaeration.1 This type of treatment obviously involves additional capital investment since it requires the construction of one deaerator with the first pumping station and additional equipment at each point where the water can come into contact with oxygen. Deaerators will increase operational costs and subsequent injection of chemicals will be required in the case of multiple degasification facilities thus increasing the consumption of chemicals. grams based on oxygen scavengers, the objective of the present study is to develop a new water treatment capable of preventing mild steel corrosion in aerated sea water. The new treatment must be able to prevent both generalized and localized (pitting) corrosion and overcome the necessity to construct and operate deaerators.

Feb 23, 2014

By MARK J. VANARELLI

Estimating ground-water inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies, including the Chattahoochee and Nancy Creek tunnels, for estimating steady-state ground-water inflows into deep rock tunnels. Statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations, and a semiempirical procedure was used to estimate ground-water inflows. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels that exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semiempirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Modeling using Monte Carlo simulations was observed to be an effective tool for removing data distribution irregularities and incorporating high-end permeability data to derive reasonable ground-water inflow estimates.

By D. Rucker

Flow models are used to predict the extraction efficiency of metals in rock piles. These models typically use hydraulic parameters obtained through column studies, which assume that the material in the column wholly represents the entire pile and the parameters can be upscaled several orders of magnitude for model evaluation. This assumption fails for parameters that are spatially variable or scale dependent. To overcome these issues, measurements made directly on the heap at the appropriate model scale can be made with the electrical resistivity method. The method aims to map the variations in the electrical resistivity, which can be associated with moisture content, degree of fines, metal content, and leachate concentration. We present an example of calibrating the resistivity with borehole measurements of moisture using geostatistics to show how the resistivity method can be used to obtain a spatial moisture distribution. It was shown that cokriging the resistivity and moisture together gives a more reliable distribution.

Jan 1, 2010

By Shailendra Chawla, Ashok Jaiswal, B. K. Shrivastva

The study aims to evaluate the pillar behavior during the depillaring operation by continuous miner (CM) technology. A panel with five headings developed as per the coal mine regulation of Indian coal mines [2] has been selected for the study. The depillaring operation has been carried out using CM technology after widening and heightening the original entries. An extensive field investigation has been carried out throughout the depillaring operation to access the mining conditions. Depillaring operation has been performed smoothly up to the middle of the panel (fourth row out of eight rows of four pillars each). Advanced blinking of the auto warning tell-tale (AWTT ) has also been observed on some of the instruments during the splitting of pillar no. 18. The panel shows extremely difficult mining conditions at this stage. The case has been numerically simulated using three-dimensional numerical techniques. The simulation result has indicated the high stress and yield condition on the working and the barrier pillar (surrounding goaf from both sides) after the extraction of pillar no. 18. The analysis has also indicated the marginal stability of the 2nd barrier pillar (namely “pillar B”). The failure of the barrier pillar could be the responsible for global instability of the panel as observed in the field. Understanding the importance of the barrier pillars, panel design has been modified by incorporating an additional row of barrier pillars. The stability of the modified panel has been evaluated. Both working and barrier pillars have been observed stable in the modified panel. This could be an alternative layout considering safety at the working face.

May 8, 2022

By Gilbert C. Robinson

Manufacturers of brick and tile are showing growing interest in the possibility of manufacture of a clay bonded block. The block would have the shape of concrete block, but would be made without the use of Portland cement, Instead, the block would be made' from mixtures' of an aggregate and the present raw materials of the brick industry. The finished units would weigh 20 to 30 pounds and meet the specifications for Grade A concrete block. The present status of the clay block development shows one manufacturer actually in production of these units$, two additional manufacturers are attempting production and many manufacturers are actively engaged in development work. At least four major research laboratories are engaged in the development program. There are several different processes available for clay block production. These processes differ primarily in the type of aggregate used or in the type of forming operation selected. I would like summarize these possible methods.

Jan 1, 1960

By T. C. Murray

An automatic control system was recently installed to insure the continuity of operation between the ship docking and ore handling facilities and the computerized conveyor-fed sintering plants and blast furnaces. Although the basic concept for material handling has not changed, many innovations including computer control have been implemented.

Jan 1, 1978

By Charles Dumaresq

The management of mine tailings poses a complex range of potential risks, including physical risks, such as the risk of catastrophic failure of a tailings facility and chemical risks such as the risk of long-term leaching of contaminants into the downstream environment. If these risks materialize, they can lead to a wide range of impacts on people and the environment, including human fatalities and severe impacts on downstream ecosystems, and the costs of recovery borne by industry, communities, governments, and society as a whole can be immense. Tailings facility failures in Canada (2014), Brazil (2015 and 2019), South Africa (2022), and in other locations around the world underscore how high the stakes are when mines produce and manage tailings (WISE Uranium Project 2019). Understandably, many people do not trust the mining industry to manage tailings responsibly. As an industry, it is our responsibility to manage tailings in a manner that is responsible and strives to minimize harm associated with tailings management, including effectively managing both the physical and chemical risks associated with tailings. Standards have an important role to play in responsible tailings management by setting expectations for standards of care and providing a means to measure and report on performance. In jurisdictions with strong legal requirements for tailings management, standards play a complementary role, pushing performance improvements in areas that may be difficult or impossible to address in legal requirements. In jurisdictions where legal requirements are lagging, standards may represent the de facto leading practice and may be the primary tool to help ensure responsible tailings management. Implementation of standards can help companies demonstrate that tailings are being responsibly managed and help build trust and credibility. Most importantly though, standards are important tools to help ensure that the risks associated with tailings are reduced, and that remaining risks are effectively managed. However, we must recognize that conformance with standards can have a down-side – the proverbial two-edged sword. Having standards is vital but there is a risk that implementing standards becomes a “box checking” exercise, with ongoing conformance leading to complacency. We must not allow ourselves to fall into the trap of believing that, just because we are complying with applicable standards and laws, we are therefore doing our best, and that “it can’t happen to us.” In addition, if conformance becomes the goal and the standard does not have mechanisms to drive continual improvement, then once the standard is met, there may be no incentive to improve. The point of complying with standards is not to pass the test. The point is to manage tailings responsibly, prevent catastrophic failures, and minimize harm. The point is to do better, because we must do better. To do that, we need to strive not for conformance, but for excellence in tailings management, driven by continual improvement and a quest to do better.

Feb 1, 2025

By Renee Royer, Allan Punkkinen

As mines progress to ever increasing depth, new challenges are encountered with serious concerns for rock excavations in highly stressed conditions. New procedures have been undertaken or are under way to remove workers from the workface, mitigating risk and exposure to hazardous conditions. Rockbolting crews are at particular risk as they are the first line of defense in the installation of the ground support systems. One such initiative for removal of workers from danger has been with remote bolting. Equipment manufacturers have had the ability to remotely inject resin pneumatically into boreholes for several years, but it has not been recognized as a very effective method due to a variety of complications. This makes the installation of dynamic support system components such as the D-Bolt® increasingly difficult. More recently, hollow-core bolts have become popular providing far more effective installation when installed with pumpable, two component urea-silicate injection resins. Normet has developed high energy dissipation self-drilling dynamic bolts (SDDB®) to meet these challenges. Following several inquiries as to the effectiveness of pumpable resins for use with dynamic support components, Normet Canada performed comprehensive testing of the bolt and resin system at CanmetMINING in Ottawa to dispel or substantiate any preconceived beliefs. Several dynamic and static tests in direct and indirect loading were carried out. Results include tests in shear and early strength UCS of the resin to measure the performance of the SDDB compared with the established D Bolt as an effective dynamic ground support component. Underground field observations, installation methodology and in-situ testing are investigated.

Apr 26, 2022

By V. K. Gupta

The phenomenon of zero order production of fines associated with the batch comminution of monosize feeds in tumbling mills has been examined in the context of the size discretized population balance model. It has been shown that the model admits zero order production kinetics only in an approximate sense. The necessary and sufficient conditions for approximate zero order production of fines have been obtained. As these conditions cannot be expressed in terms of the model parameters Sj and Bi,j alone,. several examples have been used to illustrate some of the important characteristics of the zero order production systems. One of the important characteristics of these systems has been identified as a "weak necessary condition", and the other as a " favourable condition ".

Jan 1, 1985

By Kenneth W. Luke

In the development of the ultimate pit limits for a narrow ore body, pa¬rameters necessary in the design of a functional, or working, pit become highly sensitive factors in the determination of ore reserve levels and their associated waste to ore stripping ratios. Through the use of geologic cross sections, ore reserves can be roughly calculated by utilizing a straight line approximation for pit wall slopes. The optimum position of the pit floor can be substantially altered from such a preliminary design though with the introduction of functional mining parameters, such as a ramping network, and working bench heights, berm widths, and bench to bench wall angles. Originally a computer program was developed to quickly evaluate changes in cross-section pit design with minimal alteration of input data. After developing a satisfactory technique of cross-section evaluation which incorporates working mine parameters, an optimization algorithm, or procedure, was developed and included in the program to eliminate much of the tedious manual decision-making required in determining the optimum location of the pit floor on each cross section. Optimization in this case implies the maximum profit pit. When pit and processing costs are defined or hypothesized, this computer program can be used to design the maximum profit pit, constrained by the recognized functional mining parameters. A second way of stating the optimization is that the program can be used to develop a pit design which minimizes waste stripping at any desired ore reserve level. The basic method of cross-section evaluation parallels present manual methods. Program input is a combination of data obtained directly from cross sections developed for, geological interpretation and pit design parameters selected by the mine planner. As a result it is easy for the mine planner to comprehend what the program is accomplishing, and thus participate in the development of the computer assisted design.

Jan 1, 1971