Search Documents

By Paul H. Miller

After passage by the Congress, Public Law 95-87, the "Surface Mining Control and Reclamation Act of 1977" was signed by President Carter on August 3, 1977. This law, in its simplest form, was intended to control the environmental effects of surface coal mining and to ensure that mined land is restored to a condition equivalent to that prior to mining. Immediately after the signing, the wheels of government bureaucracy began turning to establish a new federal agency -the Office of Surface Mining Reclamation and Enforcement or OSM -in the Interior Department that would implement the provisions of the Act. Since this took time and because the Congress had not yet provided funding for OSM, a special task force was assembled within the Interior Department to begin the task of writing interim regulations to implement the Act. With respect to the use of explosives, the Act specified that a blasting plan be included in the application for a mining permit. The blasting plan will outline the procedures an operator will use to meet specified environmental protection performance standards. The performance standards established by the Act require explosives to be used only in accordance with existing state and federal laws and regulations and with regulations to be promulgated by the regulatory authority. The regulatory authority was defined as either a state agency operating under an approved state program or the OSM operating under a federal program. As a minimum, it was specified that the regulations should include provisions to require that: 1) a blasting schedule be published in a local newspaper and be mailed to local governments and to all residents living within 1/2 mile of the blasting site . 2) daily notice be given to residents in the area prior to blasting. 3) blast reports be prepared that are maintained for three years and available on request to the public. 4) blasts be designed to prevent injury to persons, damage to property outside the permit area, adverse impacts on underground mines and adverse effects on ground or surface water channels or availability outside the permit area. 5) upon request of residents or property owners within 1/2 mile of the permit area, preblast surveys shall

Jan 1, 1978

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology to support Industry 4.0 has become the target of academic research in many sectors. This study reviews the trends of open-source technology, its forms, and some industrial applications. As a case study of the use of open-source hardware and software in the mining industry, this study proposed a low-cost environmental monitoring system for nonmetallic underground mines to support mine safety and occupational health. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device, and open-source software, MIT App Inventor, to develop an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a nonmetallic underground mining site to assess the performance of the system in mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors.

By Andrew Chegwidden, Tara Wilk

Construction of Shaft 17B-1, a part of The New York City water supply system, required an excavation of approximately 38 m (123 ft) through water-bearing overburden soil and more than 152 m (500 ft) of gneiss bedrock to make a connection to Water Tunnel No. 3. Ground freezing was the specified method to provide temporary earth support and ground water control for the overburden material. The ground freezing process relied on a supplemental geotechnical investigation and comprehensive laboratory testing of the frozen soil to evaluate the potential long-term creep behavior of the soil and the elimination of a temporary lining system. This paper describes that process as well as the drilling and installation methods of the ground freezing system. Additionally, the methodical system of excavation and insulation is discussed that permitted a safe and timely excavation followed by the installation of the permanent concrete liner.

Jun 13, 2023

By W. Ellison

Worldwide development of commercial markets for FGD (flue gas desulfurization) gypsum is described and used as a basis for assessing potential overall market growth and regional demand foreseen in the U.S. during the 1990s. Diverse strategies are outlined for cost-effective substitution of this major supply from acid rain control retrofits (power plant scrubbers) for natural gypsum in the principal, existing markets: gypsum board and portland cement. Another focus of utilization forecasting is a key group of related. new-product advancements including floor screeds, mining mortars and various types of innovative construction products.

Jan 1, 1993

By T. Murt, C. Oñate

In recent years, environmental considerations have played a prominent role in underground construction projects. The management and disposal of the muck produced by an EPB TBM is an important aspect of this topic. Soil conditioners with higher biodegradability and lower eco-toxicity have been specifically developed to comply with strict regulations in several countries around the world, with the goal of reducing the environmental impact of tunneling on soil, water, and living organisms. This paper highlights innovative sustainable soil conditioners and how they differ from traditional products. Additionally, environmental considerations for TBM projects around the world and in North America will be examined.

Dec 1, 2022

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

By Patrick R. Taylor

United States Antimony Corporation, at its Yankee Fork property in central Idaho, is currently using a combination of flotation, gravity-amalgamation, and concentrate cyanide leaching, silver sulfide precipitation, and activated charcoal loading to recover both silver and gold. Tine processes of flotation, milling, gravity concentration, amalgamation, concentrate leaching, sulfide precipitation and gold recovery via charcoal are discussed. The flow sheet illustrates the use of cyanidation as an alternative to shipment to a smelter.

Jan 1, 1984

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

The generation of microscopic bubbles by cavitation may enhance particle-bubble attachment and improve flotation performance. It is shown in this paper that tiny bubbles or cavities can be generated by strong shear and turbulence in high speed liquid flows. These conditions create the necessary pressure fluctuations in the bulk water to cause the local pressure to drop below a critical value. The formation of bubbles is favored by high dissolved gas contents to promote gas diffusion into the cavities, and by the presence of surfactants to provide some mechanical strength due to the adsorbed film. Experimental results on bubble formation by cavitation and consequent flotation of fine silica (d50 = 1.6 µm) are presented.

Jan 1, 1995

By Danny Chan, Shahram Tafazoli, Nicholas Himmelman, Edmond Chow

"While wearable technology has been garnering attention in the consumer market, enterprise and industry have just begun exploring its potential applications. Since February 2014, Motion Metrics International has been working in collaboration with Vandrico Solutions Inc. to apply wearable technology to improve productivity and safety in the mining industry.This article discusses the value proposition of using wearable technology to deliver critical notifications in mining. The advantages and disadvantages of various form factors are explored. The challenges, both specific to mining and in general to wearable technology, are defined. Finally, the concept of MetricsGear, the first wearable technology platform developed for mining by Motion Metrics International in collaboration with Vandrico Solutions Inc., is described. MetricsGear is designed to notify the user with minimal distraction to keep the user focused on his or her primary task and aware of mission-critical events. This focus and awareness allows the user to work more efficiently and safely. The mining process consists of a series of intricate stages, where certain events or conditions in one stage can have a huge impact on other stages. The notification of these critical events or conditions is vital for ensuring the overall efficiency of the mining process. Critical notifications can be classified as two types: timecritical events and contextual information. Time-critical events are situations where a timely response from a responder can have a significant impact on seizing an opportunity or mitigating cost. Some human-computer interaction (HCI) experts classify notification types based on the interruption, reaction and comprehension (IRC) framework. Time-critical events are classified to have high interruption, high reaction and low comprehension due to their urgency. The responder should have just enough information to identify the crisis and react as soon as possible (Chow, 2014). For example, when a tooth is lost during shovel operation, it is necessary to recover the missing tooth before it jams the primary crusher. The consequence of missing this critical time period is a jammed crusher that can cause the mine to be out of production until the jammed tooth is extracted (Baumann, 2013). In this case, the responder only needs to see an image to confirm if the tooth is missing and information to identify which equipment and when the tooth went missing (Fig. 1)."

Jan 1, 2014

By V. B. Menon, L. D. Michaels, M. E. Mullins

Introduction The cleaning of coal to remove sulfur and inorganic impurities has, in recent years, become an essential operation in any coal utilization process. US coals, on average, contain about 3% total sulfur, of which more than 60% is generally inorganic or pyritic sulfur. Existing technologies such as heavy media cycloning, selective agglomeration, and electrostatic separation have the potential for removing about 80% of the pyrite from coal (Khoury, 1981). In view of the large volumes of coal being used today, there exists a need for the development of new processes to further improve the separation of pyrite from coal. Colloidal particles in suspension possess surface charges that are related to the chemical composition of the particles. In aqueous suspensions, the surface charge is a function of pH. For coal-pyrite mixtures, it is possible, by an adjustment of the pH (also a function of polar molecules), to reach a state where the charge on coal is very close to zero, but the charge on pyrite is still substantial. The introduction of collector particles with a charge opposite that of the pyrite should then result in the selective flocculation of pyrite and collec¬tor. These flocculates should settle out much faster than coal and could be removed from the bottom of the settling column. This note discusses our preliminary observations of the effect of clay-based collector particles, especially bentonite, on the settling behavior of coal and pyrite. These experiments were conducted with a view to developing a new electrokinetic flocculation process for separation of coal-pyrite mixtures. Experimental The objective of the experiments was to determine the effects of clay-based additives on the settling rates of clean coal, pyrite, and coal-pyrite mixtures. Illinois Colchester (No. 2) coal was obtained after processing in an existing coal cleaning facility. This coal was reported to contain less than 0.3% pyritic sulfur, which was in the form of a fine powder with an average particle size of 5µm. Pyrite (of average particle size 5 µm) was also obtained from the same facility and reportedly contained less than 0.1% coal. The zeta potentials of coal and pyrite in water were measured as a function of pH using a zetameter. The pH was adjusted by adding sodium hydroxide or hydrochloric acid to the suspensions. Sedimentation experiments were conducted in 50-mL glass cylinders, and settling rates were measured by noting the height of clear liquid above the settling front as a function of time. Settling behavior was also charted by periodically taking photographs of the system. The following systems were investigated: •a slurry consisting of 2.5 g of clean Illinois Colchester coal in 50 mL of water of pH 6.0, with and without the addition of 0.5 g of bentonite (Fisher, purified grade) ; • a slurry consisting of 2.5 g of pyrite in 50 mL water of pH 6.0, with and without the addition of 0.5 g of bentonite ; and • a slurry consisting of a mixture of 1.25 g clean coal and 1.25 g pyrite in 50 mL water of pH 6.0, with and without the addition of 0.5 g of bentonite. In addition, experiments were conducted with kaolinite (Bath, South Carolina) and alumina (Fisher, purified grade) as collector materials to verify the observed effects. Results and discussion Figure 1 shows the zeta potential values for the Illinois coal and pyrite as a function of pH. The zeta potentials of coal and pyrite decrease with increasing pH, changing from an initially positive value at low pH to a negative value at high pH. The point of zero charge (PZC) for the coal is at a pH of 6.2, while the PZC for pyrite occurs at a pH of 10.3.

Jan 1, 1988

By Noriyuki Fujii

It is no need to say that exploitation of industrial minerals has a close relation to development of the industries related. In the first stage, a small scale manufactures were initiated in areas producing some main raw material minerals. China and cement manufactures, for example, were established depending on the local occurrence of raw materials such as kaolin and limestone without exception. That is, the industrial development is greatly influenced by the local production of the raw materials in the stage. With the development of industrial technology, various kinds of raw material minerals are explored to meet the demands of industries in the second stage. New materials become indispensable, and low-grade raw material minerals, which were left as useless, are developed as useful materials. In the stage, the development of raw material minerals is accelerated by that of industrial technology related. However, industries mainly rely on domestic production of the min raw material minerals.

Jan 1, 1981

By Kathy Kalenchuk

To develop strategic and tactical strategies to manage seismic hazard in a safe and economic manner, it is necessary to understand the spatial and temporal distribution of mine wide seismogenic behavior. Global mine-scale numerical stress modelling provides a means to forward predict seismic susceptibility thereby facilitating informed decision making for the development and implementation of strategic and tactical risk mitigation measures. To make forward predictions of hazard susceptibility using global stress models with reasonable confidence, it is necessary to rigorously calibrate numerical stress models to the observed history of ground reaction. This paper demonstrates quantifiable methods for calibrating numerical models and developing probabilistic prediction criterion using seismic data. The appropriate applications of model inputs (including boundary conditions, constitutive models and material parameterization) specific to global mine-scale modelling are also discussed. Lastly, this paper demonstrates how the calibration process adds value not only to informed decision making, but also to the improved understanding of site geomechanical conditions; including enhanced identification of geotechnical domains and mechanical indicators required for seismic mechanism domaining.

Apr 26, 2022

"INTRODUCTION In recent years, there has been increasing focus on environmental and social impacts of the extractive industries, climate change and resource scarcity. The concept of the circular economy aims to replaces the “take-make-dispose” economic model with one that eliminates waste of all kinds and is restorative by design. Such closed-loop systems implicitly aim to reduce the quantity of primary extracted materials entering the economy, thereby affecting supply and demand dynamics, hence mining industry economics. For the metals industry, the ability to engage in, or adapt to the circular economy can be heavily affected by industry structure and geographical factors. Eco-efficiency initiatives that reduce waste and environmental impact may help the mining and metals industry align with some of the goals of the circular economy. This paper focuses on base metals, and explores case studies in copper, lead and zinc. It analyzes primary and secondary metal production, and recycling. It examines company structures and how these affect engagement with the circular economy. CIRCULAR ECONOMY PRINCIPLES Ellen MacArthur Foundation (2012) describes the circular economy as “an industrial system that is restorative or regenerative by intention and design”, which “replaces the ‘end-of-life’ concept with restoration”, and “aims for the elimination of waste through the superior design of materials, products, systems, and, within this, business models”. The concept is systems focused. For materials such as metals, a series of loops are considered, including maintenance of devices, reuse, refurbishment and recycling. Potential methodologies to achieve circular economy outcomes include disassembly and reassembly of manufactured goods, leasing rather than buying major appliances, and converting to renewable energy sources. The circular economy is partially aligned with the principles of eco-efficiency, which relate to reducing the environmental impact per unit of a material produced. PRIMARY AND SECONDARY METAL PRODUCTION Base metals (copper, lead, zinc and nickel) are essential ingredients in modern economies and are key commodities produced by the global mining industry. Metal production can be categorized as primary or secondary. Primary metal comes from the processing, smelting and refining of metal content extracted from ores, while secondary production comes from metals recovered from recycled streams (e.g. recycled lead-acid batteries, copper wire scrap, etc.). Metals are stored in natural, anthropogenic in-use and anthropogenic waste stocks. An example of the stocks, flows and processes associated with global copper extraction and use is shown in Figure 1."

Jan 1, 2018

By J. Kelleher, R. Saulters, K. H. McDaniel, L. Griswold

To improve underground safety and visibility during mining applications, the Waste Isolation Pilot Plant designed and built a dry-dust filtration unit. The unit works in conjunction with a Spendrup 1120-70 fan with ventilation tubing to filter the face exhaust air during mining operations. The closed- loop system is designed to filter 17 m3/s (36,000 cfm) and is intended to screen 10- µm (1,250 mesh) and larger particles at 90% efficiency. To accomplish this, the unit uses a combination of Dollinger Staynew Inertial Spin filters, cyclones and traditional mesh filter media.

Jan 1, 2002

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

The process of designing pillars and selecting support measures in underground coal mines relies highly on the accurate assessment of mining-induced loads and the load-bearing capacities of the supports. This study proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology.

Jun 1, 2023

By O. Porterfield, M. O’Kane, M. Endersby

BHP Iron Ore initiated research programs in January 1995 to develop long-term plans for decommissioning waste rock material at its Mt. Whaleback operation. More than 2 Gt (2.2 billion st) of waste rock were deposited during the past 30 years. Ultimately, a total of 4 Gt (4.4 billion st) will be deposited in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semiarid climate adjacent to Newman, Western Australia. The primary research program includes the development of technology for the long-term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. Data obtained from a laboratory program and from soil-atmosphere modeling was used to design horizontal field test plots. The construction of the horizontal surface field test plots is discussed together with the field instruments installed to monitor performance. The cover system is designed to maximize infiltration during wet periods for subsequent evapotranspiration while minimizing surface runoff. The result is a near-zero net infiltration to the underlying waste material. An important feature of the design is the use of run-of-mine waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long-term performance.

Jan 1, 2000

By Gabriele Eccher, Michele Caponero, Paolo Cucino, Roberto D’Angelis

"This paper describes the optic fiber structural monitoring system implemented for Pavoncelli Bis tunnel. The paper highlights the optic fiber sensors customization capabilities, how they smoothly fit precast concrete lining processes and TBM operations, and how a lifelong service monitoring can be achieved. An overview of readings’ evolution during excavation concludes the paper.INTRODUCTIONPavoncelli Bis is a 10 km hydraulic tunnel designed to by-pass the existing Pavoncelli tunnel which experienced severe damages during the 1980 Irpino-Lucano earthquake, in south of Italy (Barla 2009). Pavoncelli Bis excavation work commenced in 1988-90, however, when excavation approached pk. 0+583 in 1992, water percolations became more and more consistent and resulted in work suspension. The tunnel was eventually sealed at pk. 0+383, leaving a flooded section between pk. 0.383 and pk. 0+583. Work resumed in 2012 where EPB-TBM excavation was adopted to cross the flooded section and to overcome complex hydro-geological conditions in various lito-types and, in particular, in the Varicolori Clay-shales area (Figure 1).Consequently, stress evolution monitoring is extremely important during construction and during the service life of tunnel lining in clay-shales and in faults areas. In particular, the paper focuses on the monitoring system proposed for the newly EPB-TBM excavated portion from pk 0+583 onwards where optic fiber sensing technology was chosen for its reading stability and reliability in presence of water and its ability to be connected in series and remotely interrogated at kilometers of distance. FBGS OPTICAL FIBER SENSOR TECHNOLOGYFiber Bragg Grating Sensors (FBGS) are gaining increasing attention in the field of experimental stress analysis. Basically, Fiber Optic Bragg Sensors are strain-measuring devices and therefore provide many of the advantages of the well-known metal foil strain gages (Kreuzer 2007).Bragg gratings are written into so called single-mode fibers. These fibers consist of a very small inner core of 4 to 9 µm diameter and an outer part (cladding) of pure glass (SiO2) of 125 µm diameter. The difference of refraction indexes between inner core and cladding causes the light to propagate only inside the small core."

Jan 1, 2016

By L. Xiao, P. Somasundaran

Using potassium oleate as a collector and alizarin red S as a modifying agent, selective depression of dolomite from francolite was achieved in an alkaline medium (pH > 9.0). Adsorption of alizarin reds alone on dolomite was found to be higher than that on francolite. Complimentary adsorption experiments of alizarin red S and oleate showed that oleate adsorprion was increased in the presence of alizaring red S. The results are explained in terms of comparative adsorption for the active sites on francolite and dolomite by oleate and alizarin red S and their interactions with dissolved mineral species in solution.

Jan 1, 1990

By J. Kretschmann, K. Sakamornsnguan

"Sustainable development is an influential ethical concept in modern mining management. However, the concept is not culturally neutral because it is based on Christian, Western values. These values can be very different from traditional values in emerging mining countries like Thailand, where Buddhist values are dominant. When applying the concept of sustainable development, these differences should be taken into account. Different values imply different interpretations of ‘good mining’. They have a significant impact on how mining operations are evaluated, perceived, operated and managed. This paper attempts to integrate Buddhist principles with approaches of the sustainable development concept. When local values are appreciated and maintained, mining companies and their external stakeholders can identify objectives and approaches that match with their own values and contexts. Practices based on this integrated ethic can help to promote sustainable mining and to minimize communication risks for enterprises in mining countries like Thailand. INTRODUCTION The objective of this paper is to integrate Buddhist principles to the application of sustainable development concept to mining activities. The structure of this paper is divided into four parts. An introduction provides basic information about Thailand, its mining industry and the role of Buddhism on the past development. The second part compares the differences between the sustainable mining framework and the implications of Buddhist principles on mining. In the third part, the core Buddhist teachings are integrated into the sustainable mining framework. This is followed by conclusions in the last part. THAILAND, BUDDHISM, AND MINING Thailand is a constitutional monarchy state in Southeastern Asia with a population size of around 65 million [1]. Its GDP in 2013 was 391 billion USD [2], predominantly deriving from manufacturing (38%), trade, transport and communication (24%), agriculture (8%) and mining and construction (4%). Still the largest part of the Thai workforce (39%) is working in the agricultural sector. The remaining part of the workforce is equally distributed across services, manufacturing, and mining and construction sectors. [3]"

Jan 1, 2015