Search Documents

By W. C. Smith

Even with conservative mine planning, rib instability can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation. sporadic zones of progressive rib instability were detected that culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1991

By M. Hepokoski, M. Klein, D. S. Yantek, L. Yan

Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives. High temperature and humidity levels inside a refuge alternative may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics Inc. to create detailed thermal simulation models of refuge alternatives with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine refuge alternative. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 35 °C (95 °F) apparent temperature limit for refuge alternatives is reasonable. The results indicate that the apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicate that the body core temperature does not reach dangerous levels even at an apparent temperature of 54 °C (130 °F). However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were raised, the water provided in a refuge alternative would have to be increased to offset moisture loss.

Jan 1, 2017

By M. Hepokoski, M. Klein, D. S. Yantek, L. Yan

Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives. High temperature and humidity levels inside a refuge alternative may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics Inc. to create detailed thermal simulation models of refuge alternatives with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine refuge alternative. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 35 °C (95 °F) apparent temperature limit for refuge alternatives is reasonable. The results indicate that the apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicate that the body core temperature does not reach dangerous levels even at an apparent temperature of 54 °C (130 °F). However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were raised, the water provided in a refuge alternative would have to be increased to offset moisture loss.

Jan 1, 2018

By Mortimer J. Richardson

Dredging can be traced to early times where it may have been derived by the Phoenicians prior to the 4th century B.C. The first tangible design drawings of a bucket ladder (BL) dredge can be found in the collections of Leonardo da Vinci (1452-1519), which he produced when he was attempting to create better methods of channel and port dredging. The perfection of the system did not commence until after the invention of the steam engine in the early 1800's; providing the impetus to progress from man-powered mud mills, horse drawn along polders or dikes in the Netherlands, England, France and Germany, to steam-driven. In the 1860's following the various gold rushes in the U.S., Australia, New Zealand, Siberia and South America, with placers in particular, efforts were begun to apply mechanization to achieve deeper digging. There is a recording of a dredge being installed to mine gold in Montana in the 1860's but did not include a processing system. Then in the 1880's in New Zealand, some practical engineers developed a system that is said to be the first bucket ladder mining (BL/M) dredge for mining gold placers. In studies of the New Zealand gold dredging experience, it is estimated that some 500 dredges were built to mine gold between the 1880's and 1942. A careful analysis of the data, however, shows that very few were profitable. The technology appeared to stagnate in the early part of the century. Two of the BL/M dredge design engineers left New

Jan 1, 1992

By K. N. Han, P. B. Queneau, A. Stojsic, M. J. Collins, V. J. Ketcham, R. M. G. S. Berezowsky, W. D. Vardill

The bulk of the ore found in the Lihir Island deposit is refractory in nature, with the gold contained in auriferous pyrite. In support of an evaluation of the development of this deposit by Kennecott (a wholly owned subsidiary of RTZ) and Niugini Mining Ltd., testwork has been carried out at the Sherritt Research Centre to demonstrate the amenability of the Lihir ore to pressure oxidation pretreatment to liberate the refractory gold. The results of pilot plant treatment of the Lihir ore in a continuous circuit with a feed rate of between 10 and 30 kg/h ore are described. The integrated circuit comprised pressure oxidation, residue washing, and gold recovery from the washed residue by carbon in leach or carbon in pulp cyanide leaching. Significant factors affecting gold recovery included temperature and retention time in the pressure oxidation step, and the concentration of soluble chloride in the feed. Gold extraction from well washed ore, after oxidation at 210°C for 66 minutes in the autoclave, was typically between 94 and 96%, compared with less than 30% by direct cyanidation.

Jan 1, 1993

Machine breakdowns and maintenance delays are large contributors to lost production and increased operating costs in the mining industry. The U.S. Bureau of Mines is investigating the applications of expert system technology to diagnostic and predictive maintenance tor mining equipment. This will help increase mining productivity and decrease operating costs, by reducing the frequency of equipment failures and repair times. The Bureau has begun this effort by applying expert system techniques to the diagnosis of hydraulic system problems on a continuous mining machine. This paper discusses the development of the hydraulic diagnostic expert system.

Jan 1, 1990

By Shu Fan Chau, Innes Duncan, Harry Asche, Bill Newns

The North Auckland Line (NAL) in Northland, New Zealand, is being upgraded to pass Hi-Cube containers. The line includes many tunnels and bridges which need to be refurbished to improve structural clearances and line capacity. Tunnel 2 along the line, the Makarau Tunnel, has posed special challenges. Opened in 1898, the tunnel suffered multiple collapses during construction and has shown significant distortion during operation. The tunnel has been repaired many times since opening. Successfully enlarging this delicate and distressed structure has involved historical research, advanced analysis and design, and careful construction. The results provide lessons for dealing with brick lined tunnels and poor ground conditions

Jun 13, 2021

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where processing begins; over- burden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50 percent of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8 in. range) are the accepted economic answers for bulk materials handling over reasonable distances.

Jan 1, 1968

By GRANT COLLIGAN, BROCK O’KELLEY, Corby Anderson

With the world’s ever-growing push to expand technological capabilities, the need for specialized materials including rare earth elements has exploded. One source of rare earths found in the United States is bastnaesite, a rare-earth-bearing fluorocarbonate, mined at the Mountain Pass Mine in California. To increase production, it has been essential to optimize existing processes and create new ones to capture current reserves. This paper presents the results of a research program conducted to expand the understanding of the bastnaesite leaching system. With the help of prior knowledge and thermodynamic calculations, a novel single-stage hydrochloric acid leach system was created to optimize the extraction of rare earths from bastnaesite. Historically, this extraction has entailed the use of a two-stage leach system involving a high-temperature hydrochloric acid leach followed by a caustic crack. We ran a series of single-stage leach experiments by reacting locked-cycle flotation concentrate with hydrochloric acid to test common leaching parameters. The results of these single-stage tests showed significantly higher rare-earth recoveries than the reported recoveries of the historic two-stage caustic crack processes, all while decreasing the number and amount of reagents needed.

Feb 1, 2023

By Yi-Hsuan Chen, Jürgen Brune, Candace S. J. Tsai, Alejandro Munoz, Connor Krause

This study highlights the significant presence of submicrometer- sized airborne particles in underground coal mines, especially around the belt conveyor drift areas. Using realtime instruments and gravimetric samplers, the assessment revealed that particle concentrations were notably higher in the belt entry compared to other locations, with a strong presence of submicrometer- and nanoparticle-sized dust. The study’s findings emphasize the importance of addressing small particle exposure, as these particles, composed of harmful substances like calcium, copper and iron, can pose serious health risks to miners. This research emphasizes the importance of improving air exposure estimation through more effective monitoring and characterization techniques to better understand and reduce workers’ exposure to hazardous airborne particles in the mining environments.

Apr 1, 2025

By D. C. McIntire

The Homer City Station, jointly owned by New York State Electric and Gas Corporation and Pennsylvania Electric Company is a three unit coal fired station. The first two units were put into commercial operation in 1969; the third unit became commercial in 1977. Units 1 and 2 are subject to the Pennsylvania State Implementation Plan (SIP) emission limit of 3.7 pounds of S02 per million BTU. Unit 3, having started construction later, is subject to the Clean Air Act, New Source Performance Standards emission levels of 1.2 pounds of 50-2 per million BTU.

Jan 1, 1988

By R. E. Pennington

My subject this morning is coal liquefaction technology. Actually, coal liquefaction involves a number of technologies in a very complex system. The first slide shows the major components of such a system with arrows to indicate appropriate flows. The components are the facilities for coal feed preparation and handling; the coal hydrogenation or base liquefaction section; facilities for product separation and recovery, and in addition, facilities for the production of hydrogen from coal-based sources. A very rough break- out of the investments involved in these areas is given at the bottom of the slide. Investment is spread about equally among the three areas of operations Another way of looking at it is that the investments in what might be called support facilities are of the same magnitude as the base investment in the hydrogen facilities. Therefore, it is appropriate in a discussion of coal liquefaction technology to treat it as a system composed of a number of technologies. The next slide lists the various functions in the feed preparation section along with an indication of technology status. Storage, crushing, grinding, drying of coal all have been in commercial practice for a number of years. The slurrying and pumping of coal at least in water slurries, is practiced commercially also. The heating of coal slurries in oil to high temperatures under pressure is not in commercial practice and development and testing is going on by a number of people in this area. Some rather complex phenomena occur when coal oil slurries are heated to high temperatures.

Jan 1, 1975

By Eugene Honeycutt, David Gallagher, R. E. Melley, Nick Madison

Drummond Co. Inc.'s Shoal Creek Mine slope conveyor is the highest lift, highest horsepower, highest tension conveyor system in North America. The system has a capacity of 4950 t/h (5500 tph), a vertical lift of 360 m (1180 ft) and a total connected power of 6000 kw (8000 hp). The mine will include 2 longwall machines and 5 to 7 development sections. Annual raw production will approach 9 million tly (10 million tpy). This paper describes the early investigation of system capacity, haulage system options, and the final selection of a single flight belt conveyor. It will review the basic system de- sign and equipment selected. Also included will be some highlights of the installation of the conveyor system.

Jan 1, 1996

By Gregg R. Bierei

Arch of Illinois is a mining complex comprised of two surface and two underground mines located in Perry County, in southern Illinois. The company a division of Apogee Coal Co. of St. Louis, MO. Arch of Illinois' two surface mines, the Captain and Horse Creek Mines, use large stripping shovels and cross-pit bucketwheel excavators to remove overburden from three seams of coal, the Herrin No. 6, Harrisburg No. 5 and Danville No. 7. All are considered high sulfur reserves. The two underground operations are managed by Arch of Illinois. They are the Kathleen Mine and the newly constructed Conant Mine, which began production in 1991. Both underground mines are continuous miner operations. They mine the No. 6 coal, which is about 1.8 m to 2.1 m (6 to 7 ft) thick. All coal is currently transported by truck to a central preparation plant located at the Captain Mine. This preparation plant produces 27 kt/d (30,000 stpd) of clean coal. Production in 1992 reached 5.9 Mt (6.5 million st) of saleable coal. Of that, about 66% or 4 Mt (4.4 million st) are produced by the surface mines and the rest the by under ground operations. Change is in the wind for Arch of Illinois. In 1988, 100% of all production (6.2 Mt or 6.9 million st) came from surface operations. By 1995, only 38% of production is scheduled from surface mines. And by the year 2000, 100% of production will from underground mining methods. Dwindling low ratio reserves, compounded by increasing environmental and land acquisition costs, coupled with more efficient underground mining equipment, have started an evolutionary trend toward development of underground reserves. For Arch of Illinois to maintain profitability of remaining surface reserves and to compete effectively mining underground, it must improve efficiency, productivity and cost reductions. These efforts are essential for maximizing current surface reserves and to ensure a continued existence in the presence of clean air legislation and the softening of the high sulfur coal market.

Jan 1, 1993

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying an atomic force microscope (AFM) and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy to study in situ the adsorption of three different collectors — oleic acid, octanohydroxamic acid (HA) and salicylhydroxamic acid (SHA) — on bastnaesite in aqueous solutions. The results show that all three collectors adsorb on bastnaesite. The hydroxamic acid collectors — HA and SHA — adsorb on bastnaesite mainly in the form of insoluble metal hydroxamate. Their specific adsorption mechanism indicates that high selectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By George W. Heunisch

The properties of Neutra-Fix® and Neutra-Ment® , two new lime substitutes for the treatment of acid mine drainage (Arm), have been compared with lime and Alkament®, two products presently in use for AMD treatment. The two new products are basically dolomitic byproducts and produce sludges that are more compact than those from lime. Sludge settling rates are faster than lime with iron concentrations after 24 hours that comply with EPA regulations. Material utilization and optimum pit are reported.

Jan 1, 1984

By D. J. MacKinnon

Smooth, compact, dendrite-free, 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartment con- taining DSA anodes which were separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air-sparging. The catholyte passed through the diaphragm into the anode compartment from which chlorine gas and spent anolyte were withdram.

Jan 1, 1980

By William G. Freeman

In comparison to many mineral commodities, barite has a low unit value. It is mined and sold in low volumes in high-grade (90-98% BaSO4) forms to basically one industry that uses approximately 75% of the free world production. Based upon the above criteria, all factors must be considered in determining if a barite deposit is economical; such as, the type of deposit, mining and milling methods required, transportation to the markets, tariffs, local political conditions, etc. In other words, barite mines are made--not found. The length of this paper precludes any indepth discussion of geology, mining and metallurgy of barite. Most of this information can be found in data already published, such as D. A. Brobst's bulletin1 on the Barite Resources of the United States.

Jan 1, 1971

By K. J. Reid

With the current trends of increasing costs and decreasing head grades the mineral industry is no longer operating in very high profit areas and has been forced to pay greater attention to the application of modern technology. Although here are many technological advances to the credit of the industry in recent years there are still many processes being operated in the traditional manner and still many areas awaiting the application of methods which have been proven in other industries. Compared with the chemical industry the mineral industry is seriously ageing in the general areas of process analysis and process control, more so than can be justified by the complications arising from having to deal with particulate systems with properties far different from ideal, or even non-ideal, liquid systems. One area in which there has been a remarkable lack of application in the Mineral industry is that of analog computation and the authors feel that there is considerable scope for the use of the analog computer in studying mineral industry processes. The paper outlines the basic principles and features of the analog computer and describes its role as a simulation tool in some engineering and mineral processing systems.

Jan 1, 1972