Search Documents

By R. Woods, J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher.

Jan 1, 1976

By Walid M. Abdellah, Soliman Abu Elatta A. Mahmoud, Hanaa A. Abu Khoziem

The high-grade Th-U-Y zone is one of the numerous mineralized zones found in the El Garra El Hamra hydrothermally altered syenites in southwestern Egypt. It is characterized by the thorium minerals thorite and thorogummite, which are closely associated with xenotime-(Y). This zone of mineralization is localized in the eastern part of the El Garra El Hamra hydrothermally altered syenites. This zone does not relate to the first phase of syenites that appeared on the surface but is linked to the other, hidden phase of the syenitic body. Additionally, the fluids responsible for the mineralization of this zone belong to the late-stage hydrothermal event as well as the fault action due to the fact that it had continued reactivations for a long period of time. The studied mineralized zone also contains ceriopyrochlore-(Ce),(Ce,Ca,)2 (Nb,Ta)2O6 (OH), fluorite (CaF2) and barite (BaSO4), which are found in considerable amounts, whereas apatite (Ca5(PO4)3F) and chromite (FeCr2O4) are rarely found together with Fe-oxi-hydroxides (hematite and goethite) with a minor amount of jarosite (KFe33+(OH)6(SO4)2). Finally, the main constituent mineral in the zone is the pseudomorph perthite in addition to quartz, which is found as deformed crystals. A technological sample was collected from this zone and was found to assay 4.62 weight percent thorium (Th), 0.37 weight percent uranium (U) and 3.12 weight percent rare earth elements (REEs). From the chemical and mineralogical composition of the studied technological sample, the leachabilities of Th, U and REEs were investigated using sulfuric acid (H2SO4) agitation leaching and pug leaching methods. The latter was found to be preferred under the conditions of 0.54 ton H2SO4 per ton of altered syenite at 110 °C for two hours.

By D. E. Ranta

Orebodies with intricate three-dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer-assisted methods. The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist's interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral deposits.

Jan 1, 1984

By Young C. Kim

Because of the tremendous technological advances achieved in recent years in microcomputers, it is not only technically feasible but also economically viable to develop an automatic truck dispatching system using a microcomputer. Such an effort was initiated by the Department of mining and Geological Engineering, University of Arizona in the summer of 1983. Up to date results and experiences prove that today's microcomputers can be economically employed for such a system to be used at small to medium scale open-pit mines. An IBM/XT microcomputer with 10 MB harddisk storage, together with automatic sensing capability of truck movements at several key locations in the pit, formed the core of this system. System software is written primarily in MICROSOFT FORTRAN with supporting subroutines in MACRO assembly language. The software is designed to automatically monitor truck movement throughout the pit, to make heuristic assignments based on expected shovel availability and truck travel times, and to record production statistics. It is currently dimensioned to handle 50 trucks, 10 shovels, 10 dump sites and 3 material types. Due to the lack of funds to purchase the necessary communications hardware, the work related to the automatic sensing of truck movements has not been performed to date. Otherwise, the automatic truck dispatching-system is fully operational on a realtime mode.

Jan 1, 1984

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The overburden responses in gently inclined orebody mining are different from those in horizontal orebody affected by the orebody dip angle. In particular, the mining-induced stress presents asymmetrical distribution characteristics spatially, resulting in stress concentration and large-scale pressure relief phenomenon in the surrounding rock. As a result, frequent ground pressure disasters such as roof collapse and barrier splitting occur frequently. Moreover, the ground pressure evolution law and the interaction between stopes in multistope mining are complex. The effective ground pressure control measures cannot be taken due to unclear understanding of the evolution of stress and displacement fields, justifying the investigation of the distribution and evolution of underground pressure for safe and efficient mining.

Jun 1, 2023

By T. N. Andersen

The history of gold and silver analyses shows an interesting duality. On one hand, classical chemical and instrumental methods have evolved to meet changing needs, but on the other hand, the age-old and somewhat empirical fire assay has remained a popular tool. Inasmuch as gold and silver generally have been present in ores at low concentra¬tions, methods have been challenged by a need for sensitivity and selectivity coupled with reasonable assay time. A progressive increase in the importance of low grade materials as ore sources has led to the need for improved methods. Assays of these materials are required for process control and accounting in operating plants as well as for guiding research and development activities. The analytical response to these needs is evidenced by numerous reviews published through 1977-¬e.g., cf Kolthoff and Elving (1966), Beamish and Van Loon (1966, 1972, and 1977), Young (1971) , Mallett (1970), and Sen Gupta (1973). In this paper we present a brief sketch of the history and status of various gold and silver methods. A more detailed summary of atomic absorption spectroscopy (AAS) is Given, as this method has gained in popularity more than other assay methods. AAS methods currently in use are summarized and discussed briefly. This paper is not meant to be a detailed review, as are the above mentioned publications. Rather, we borrow from those works and more recent papers to report trends in gold and silver analyses (particularly in AAS). Also, we discuss some selected poten¬tial problems, and problems that have been experienced by this laboratory.

Jan 1, 1981

By F. Dudouit, M. M. Mohkam, F. Renault

The Pannerdensch Kanaal Tunnel is part of Holland’s Betuweroute high speed freight railway project linking Rotterdam to inland of Europe. It comprises of twin tunnels, 1620 m long each, with 8.6 m inner diameter. The Tunnel alignment is situated mainly in sandy formations and under high hydrostatique pressure. The over burden cover varies from relatively high to very low, sometimes much smaller than the diameter. One of the special features of the Pannerdensch Kanaal Tunnel is that, over some 250 m, the twin tunnels are to be bored in a back?lled sandpit. Some 490 000cubic meter of sand has been placed and compacted by vibro-?otation to refill the sandpit. The tunneling machine is a 9.8 m slurry shield manufactured by Herrenknecht. Tunnel lining is precast concrete consisting of seven plus one key universal segments. Other than the special feature of boring through re?lled sand, constraints such a slow overburden while crossing under Pannerdensch Kanaal and some lagoons, as well as high liquifaction potential of sandy formations, render this job very unique of the type. Fine studies were conducted in heading’s stability. And, confinement pressures were determined considering different risks of liquefaction and blowout problems. Both tubes have been successfully bored. Several sections have been monitored. The results are quite interesting and in accordance with contract technical conditions.

Jan 1, 2003

By C. L. Emery

The geology and early history of the discovery of potash in Saskatchewan as described by Heber Cole (1) and R. V. Thompkins (2) has dealt with the distribution of the salt beds and their potash content. From the many bore holes through the Prairie Evaporites the outlines and contours of the series have been well established. The thickest section of the salt beds lies to the north of the "barren" area and forms a belt running easterly to a point west of Yorkton. The "barren" area is a region where the salt has been redissolved and the strata have slumped down, to fill the voids. This area is of interest from the standpoint of rock mechanics. The potash-rich beds extend both east and west of the region. mentioned and the top of the Prairie Evaporite is at a depth below 3200 feet from the surface near Saskatoon and dips southerly at an average rate of about five feet to ten feet per mile.

Jan 1, 1966

By T. R. Ellis

"In August 2013, the Appraisal Practices Board of the U.S. Appraisal Foundation issued its “APB Valuation Advisory #4 - Identifying Comparable Properties,” which contains analysis and examples that may suggest a broader meaning of the term “comparable properties” than is current convention in real property value appraisal in the United States and internationally. The advisory is directed at the appraisal of real property of all kinds, including interests in mineral properties, as indicated by the inclusion of two mineral property appraisal papers in the appendix that lists suggestions for further reading.This paper firstly reviews as background the historical meaning of a comparable property, with its perceived constraints, against real-world examples of transacted mineral properties that are adjusted to subject properties to provide market value indications. The advisory’s findings are then examined and evaluated as to whether they may influence and benefit the work of mineral property appraisers, particularly in situations where their sales comparison analyses may be challenged. The conclusion is that the combination of constraints that the advisory’s findings specify for use of the term “comparable” will for mineral properties be met infrequently or rarely. As a result, mineral property appraisers are advised to avoid using the terms comparable or “comp” when referring to transactions of mineral properties that they analyze to derive data for appraising the value of their subject mineral properties. IntroductionA mineral property appraiser rarely finds a sale of a mineral property that meets the literal meaning of the term “comparable sale,” by being directly comparable to the subject property of the appraisal in all factors of significance in the determination of the value of the property interest being appraised. Real estate appraisers have long used a more liberal interpretation of the meaning of comparable sale and its commonly used abbreviation, “comp.” Real estate appraisers compare sales to their subject property on the basis of price per hectare or acre of land and price per square meter or square foot of building floor area. Adjustments totaling to within the range of +30 to -30 percent from the sale property to the subject, before factoring in the property area, have generally been viewed as appropriate for the sale to be considered a comparable sale."

May 1, 2016

By Ed Schodowski

Wireless technology is a hot topic for anyone involved in the design, operation, maintenance or upgrading of mines or mineral processing plants because wireless technologies overcome barriers that have prevented many useful data inputs. Wireless communications can contribute to worker safety, satisfy environmental concerns, support plant security, track human and physical assets, and improve equipment maintenance. The cost structure of wireless is compelling and users can realize savings ? up to 90 percent less installed cost than wired instruments ? since wireless technology eliminates the need for expenses associated with cabling, engineering, construction and documentation. Many applications previously considered too expensive have become economically feasible with wireless. Two examples are continuous monitoring of safety showers to notify operators when one has been activated, and monitoring effluents to ensure environmental regulations are being met. In many cases, wireless transmitters can be installed where wired devices were too expensive to justify, or were not feasible due to physical or technical barriers. Examples include monitoring temperature measurements inside a rotating reactor or monitoring process variables in a tough, corrosive environment too challenging for a wired solution. Wireless also gives operating personnel mobility with the ability to communicate from remote or hard-to-reach zones. According to a recent Venture Development Corp. survey covering radio frequency (RF) of microwave industrial monitoring and control products, these features are contributing to the expected nationwide growth rate for industrial wireless applications of 19 percent annually from 2007 to 2012 (Taylor, 2008). At the same time, mineral producers have many questions about wireless systems including their applicability, reliability and security in this industry. Just what can wireless do? Is it secure and reliable? Can these instruments stand up to the rigors of the industry? Can wire-less technology provide the flexibility needed for mining applications?

Jan 1, 2009

By T. Krichler

"Current mine control stations are either single-position systems with high engineering effort or all-in-a-box solutions with low integration possibilities of third-party devices. Above all, both approaches are cost-intensive and not feasible for small companies. This paper shall be an inspiration of how to enhance the productivity and monitoring of an existing mining system in a modular way by introducing a proven technique of the ongoing digital revolution: A Wi-Fi network based on the communication protocol OPC UA. The starter kit consists of a single-board computer, a WLAN access point and any electronic sensor. INTRODUCTION The majority of the European mining industry is run by small and medium deposits (Europe Geology, 2017). This is due to the fact that most ore mines in Europe are widely distributed within the continent, are generally small and additionally they are often steeply inclined. Such ore bodies are normally mined with underground mining methods and must be excavated with high selectivity because of their small thickness. That is why the economy of scales, higher efficiency through bigger machines, cannot be used in most deposits in Europe except for lignite mines. It is important to find an alternative possibility to improve the efficiency of European mines for making them competitive internationally. For cost optimization and profit maximization it is necessary to use the trends of industry 4.0 and to broadcast these into the mining industry to reach a technological advantage. The goals of the EU within the Horizon 2020 funded project are to shorten the actualisation of the mine and block model to hours, improve the communication with Through the Earth (TTE) via very- or ultra-low frequency for long-time monitoring of the abandoned workings, and develop a cost-effective mine control station for optimization of mining processes in Small and Medium Enterprises (SMEs) as well. This paper deals specifically with the new approach for data acquisition, transmission and visualisation of a mine. SCADA AND ERP IN MINING There are already many Supervisory Control and Data Acquisition (SCADA) and Enterprise Resource Planning (ERP) programs on the market, but these are normally not developed for the mining industry. At the moment this leads to three options. • To hire a system integrator, who shall build a complete control station for one mine that requires a high amount of knowledge in programming and cannot be maintained by the mining company itself. • To buy different types of out-of-the-box systems, whereby every system can include some of the used technology. In this case a huge amount of project engineers and operators – at least one per system and shift- is required. • To buy every machine and program from one company including the service contracts."

Jan 1, 2018

Two key strategies for a new generation of mining are developing domestic raw material production and doing so in an environmentally responsible way, according to presenters at the 83rd annual meeting of the SME Minnesota Section in Duluth (the 71st annual University of Minnesota Mining Symposium). From technical sessions detailing how to build com-munity support, to a short course on international perspectives in iron ore mining and processing, the two-day meeting emphasized the potential of Minnesota state deposits and the importance of maintaining productive community relations both locally and globally. The meeting of more than 300 mining industry professionals began on April 20 with a traditional convocation celebrating the values of northern Minnesota. The accompanying tradeshow, with a record 131 booths, showed the speed and vigor of the economic rebound. Keynote speaker Scott Anderson, vice president and senior economist at Wells Fargo, stated the prevailing mood of the conference: ?Wow, what a difference a year makes.? With metal prices and sales up and heading higher, he said, it was clear that the production-centered economic recovery is reaching the mining and the minerals industry. However, Anderson sounded a few notes of caution. Serious threats to economic stability remain, including the burgeoning national de?cit, high unemployment and the still out-of-control foreclosure crisis. Overall, he predicted a below-average recovery and stressed the importance of developing a long-term business strategy.

Jul 1, 2010

By David A. Zegeer

Since 1980, more than 40 miners have lost their lives by being trapped and suffocating in stock-piles, bins, silos, and similar facilities. Mine Safety and Health Administration (MSHA) is concerned about these accidents, most of which could be prevented if management and miners appreciated the hazard. In February 1986, the coal industry had a suffocation accident that drew national attention. A group of engineers were standing on a coal stockpile. It gave way under their feet. Five of the engineers were buried in the coal and suffocated. As with all fatal accidents, MSHA investigated the cause of this tragedy. I also asked my staff to look into the history of similar accidents. I found out it is rare to have multiple fatalities due to suffocation in material. But, over the years, there has been a long series of individual fatalities from this type of accident. Here are some examples. In Oct. 1985, a coal mine employee in Virginia entered a hopper to collect a coal sample. The feeders were started while he was standing in the hopper. He sank into the coal and suffocated. In Sept. 1985, an employee at a Texas sand company climbed onto a surge pile, to check a problem with sand flow. When other employees found him, the sand had swallowed him. Only his face and one hand were showing. Though the victim's face was clear of the sand, he suffocated before rescuers could free him. Many people do not realize you can suffocate in this kind of situation, though your head is free. Every time you exhale, the material has room to shift and press harder against your chest. Then you have less room to inhale. If this goes on long enough, it gets to the point where you cannot inhale at all. That is what happened to the victim in this accident. In May 1985, a plant operator at a Wisconsin sand and gravel operation purposely slid into the drawhole of a surge pile. He tried to break up large rocks that were clogging the drawpoint. Material piled on the side of the surge pile slid down and buried him. The operator was wearing a safety belt and line. But he was covered by 3 to 3.7 m (10 to 12 ft) of material and could not be pulled free. This incident illustrates another point. A safety line can help. But it is not enough. Workers should never put themselves in a position where loose material can fall on them from above. In Jan. 1985, a young Utah coal miner was waiting for a ride home from a co-worker whose job was at the tipple. A jam developed in the coal bin. The men could not clear the jam from the outside. So the young miner jumped into the bin. He started digging with a shovel at the toe of the coal pile. It caved in on him and he suffocated. The young miner had only three months of mining experience. He had not been trained for work around the coal bin. Since 1980, 16 coal miners and 26 nonmetal miners have lost their lives in loose-material suffocation accidents. Suffocation accidents occur in many areas around mines - bins, hoppers, stockpiles, surge piles, and silos, among others. One recent accident occurred at a surface coal mine in Illinois. The victim was walking over an area that had been drilled and blasted the week before. He fell into a void that had been crusted over with earth. He too suffocated. And many materials have been involved in suffocation accidentscoal, crushed stone, sand, salt, different kinds of ore, ammonium nitrate pellets used in blasting, and a powdery byproduct of iron ore milling called calcine. In addition to fatal accidents, there are near misses. We do not know how many. Most of them are not reported. A person who gets trapped in material, but is rescued, is usually unhurt. MSHA sometimes hears about these accidents by chance, or because they are reported in the local media. We do know that near misses are happening far more often

Jan 1, 1987

By Frank F. Aplan, Edward C. Jr. Dowling, Richard R. Klimpel

Thirteen kinetic models that mathematically describe the flotation process have been statistically evaluated for the flotation of copper, lead and zinc ores. Comparisons have been made for a variety of circuits involving roughing, cleaning, scavenging and regrind followed by cleaning. Variations in collectors, frothers, depressants and activators have been considered. Based on the statistical criteria used for the evaluation, and the reagent, circuit and ore variations studied, the most reliable flotation models have been identified and subsequently used to characterize the metallurgical results.

Jan 1, 1986

By Robert Bissonette, Samir Sbai

A critical component of implementing autonomous systems is the ability to use information from a robust sensory and information system to make sound, predictable, and repeatable decisions to assure safety. This means that any such system would need to evaluate what objects (people, equipment, boulders, etc.) of interest exist in that environment (with relevant data about identity, trajectory, characteristics, etc.), project a future continuum of those objects (including considerations for variabilities), and make control intervention choices to minimize risk due to exposures in the present operational area. The components of an overall system would include: a) sensor and data fusion, b) probability projection of future states, c) generation and evaluation of alternate futures, and d) implementation of best course of action to reduce risk. The National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD) is studying this framework for applications for autonomous mining equipment. This paper focuses on using information from the sensor fusion engine to generate a continuous projection of future and alternate states (b and c above) incorporating the factors of confidence, accuracy, tolerance, and other variabilities. We refer to this as Machine Situational Awareness (MSA).

Jun 25, 2023

By John C. Gould

GENERAL DESCRIPTION The Climax mine is located 161 km (100 miles) southwest of Denver on Fremont Pass astride the Con¬tinental Divide. Climax employs 2800 people to pro¬duce 42 670 t/d (47,000 stpd) of molybdenum ore. The Storke level, the main underground level, produces 19 970 t/d (22,000 stpd); the 600 level, the lowest ac¬tive underground area, produces 7260 t/d (8000 stpd); and the open pit presently produces 15 430 t/d (17,000 stpd), Fig. 1. A panel caving method is possible because of the favorable geology and geometry of the Climax ore body. Geology The Climax deposit is composed of three separate ore bodies formed in a massive Tertiary stockwork which penetrates Precambrian granites and schists. The ore bodies are elliptical in plan with overall dimensions of 914 x 1219 m (3000 x 4000 ft). In section the ore bodies are arcuate with an overall height of 457 m (1500 ft), although the depth is not firmly ascertained. Ore grade decreases rapidly into a highly siliceous cen¬tral core and more gradually toward the outer bounda¬ries of the deposit. The mineralization is relatively continuous in the ore zone and contains few dilution-causing waste inclusions. Molybdenite is contained in pre-ore fractures which were largely recemented during the three mineralization pulses. Postore fractures, with a spacing of a few inches to several meters (feet), render the deposit amenable to caving when it is undercut. The peripheral rock caves similarly to the ore, but the central core is competent and is difficult to cave. Caving Feasibility Successful caving action requires an undercut area of approximately 122 by 122 m (400 by 400 ft). When the undercut area exceeds this minimum distance, the arching effect is lost, and the ore column collapses. Ore extensions from the main cave area less than 122 m (400 ft) wide usually cannot be caved. Waste or low¬grade areas within the deposit can be left if they are large enough to carry weight around openings passing through them. Experience indicates that these areas should be over 30 m (100 ft) in length and width. Smaller unprofitable units of waste, such as postore dikes, are mined to avoid weight problems and result in ore dilution. Successful caving and ore recovery are dependent upon timely ore removal from the undercut zone because columns of immobile ore inhibit caving and concentrate weight onto the underlying workings. Climax experience indicates that a finger (drawpoint) spacing* averaging 10.4 m (34 ft) yields an excellent caving action and a 92.5% ore recovery at the estimated grade. An additional 15% of the ore is recovered-at a diluted grade (Fig. 2). Mine Layout The slusher drift is the primary production facility (Fig. 3). The ore is undercut and caved into the fingers,

Jan 1, 1982

By A. V. Castelli

Since the record year of 1981 through 1985 the tonnage of weighting materials (barite and other heavy minerals) used in drilling fluids has decreased an estimated 49%. As in the past, barite still makes up over 90% of the minerals used for weighting materials in drilling fluid. Domestic production of barite has decreased 69% since 1981 and imported barite has made up over 50% of the total barite consumed since 1982. See Figure 1 for usage of barite. The number of operating grinding plants has decreased from 69 in 1982 to 39 at the end of 1985. With the decrease in demand of weighting materials for drilling fluids and an over capacity of grinding existing, prices for weighting materials have decreased dramatically. Although the American Petroleum Institute has not changed any of the specifications for barite, some users have initiated their own new specifications and have proposed to have them included in the API specifications. The exploration for and development of oil and gas dictates the level of weighting material used in the drilling fluids industry. Most forecasters do not foresee (or predict) increases in the level of drilling until the 90's. The primary or unground barite produced in the U.S. mines has a difficult time competing with imported barite due to the location of the mines. These mines are located in North Central Nevada, with small tonnages being produced in California, Missouri, Illinois, Montana and Washington. The major reason, is the difference in transportation costs from the mines versus ocean freight rates from the foreign ports to the major area of use, the U.S. Gulf. Since 1981, the production of primary barite has decreased from 2,849,000/ST (2,584,596/MT) in 1981 to an estimated 890,000/ ST (807,403/MT) in 1985(1). If it were not for the use of unit trains by some producers the production of primary barite in the U.S. would have probably declined another 20% in 1985. During the same period, of the total amount of barite consumed in the U.S., imported barite ore increased from 417, in 1981 to 65% in 1985. The major exporting countries to the U.S. during this period were China 46.27, Morocco 15.27., Chile 10%, Peru 8.4%, India 7.9%, Mexico 5.4%, Thailand 3.9% and Ireland 2.3%.

Jan 1, 1986

By Stanley J. LeFond

The Republic of Botswana, one of the newer countries of southern Africa, attained independence on September 30, 1966. It covers an area of about 225,000 square miles (582,000 square kilometers) which makes it slightly larger than France, or slightly smaller than Texas. It is bounded by Zimbabwe, the Republic of South Africa and Namibia, including the Caprivi Strip. Angola and Zambia are close neighbors. (Map 1). Botswana lies at the center of the southern African plateau at a mean elevation of 3,300 feet (1,000 m). It is a natural habitat for most species of African fauna. The rolling sands and extensive grasslands of the Kalahari Desert cover the southwest. The climate is sub- tropical. Summers, although tempered by north- easterly breezes, are hot, but mean maximum temperature seldom rises above 100°F (38°C). Winters are dry with wide temperature variations, which often give rise to frosts.

Jan 1, 1981

By David J. Brown

Extensive deposits of bituminous, subbituminous, and lignite coals occur in the western United States (Figure 1). Over one trillion tons of identified resources have been located and inferred by geologists and more than 200 million tons of western coal are mined annually (1). In the future, production of western coals will increase significantly and approach national production levels of higher-rank eastern coals. Western coals will be utilized in new power plants as a replacement fuel for oil and gas and may be used in advanced technologies such as diesel engines or in direct-fired turbines. Since these applications require low-ash, low-sulfur coals, crushing to fine sizes and significant cleaning to remove minerals and sulfur will be required. Coal cleaning traditionally has been associated with reducing pyrite and other mineral matter from high-rank eastern coals. To date, insignificant quantities of western coals have been cleaned before utilization and limited data on their washability characteristics exist. Because of this lack of data, it is difficult to predict how these coals will react to standard washing techniques.

Jan 1, 1985

By B. E. Davis, D. A. Stanley, C. E. Jordan

A prototype expert advisor was developed by the U.S. Bureau of Mines to systematically offer advice on the control of a Florida phosphate operation. The PC based system receives input from remote sensors for circuit parameters such as feed rate, reagent addition, and pH and from operator entered information such as the quality of the concentrate and tailings in each of the coarse, fine, and amine flotation circuits. The computer evaluates the information using rules obtained from industry representatives and Bureau flotation experts. Recommended actions and questions are displayed to quickly guide the operator to a problem within the flotation circuit and suggest a solution. This process control system could provide more uniformity among the flotation operators and also serve as a trainer for new operators. In addition, it represents a step toward fully automated systems for phosphate flotation.

Jan 1, 1990