Search Documents

By John Neale, Robert Huberts, Tony Pinches

A major R&D programme for the application of bacterial oxidation to the pretreatment of refractory sulphide gold ores was started at Mintek in the early 1980s. This arose from an established expertise base in the bacterial leaching of base-metal sulphide ores. The refractory gold programme has been supported by a number of South African gold-mining companies, but major support has been provided by the Anglo American Corporation of South Africa (AAC) and the AAC Vaal Reefs Exploration and Mining Company Limited · (Vaal Reefs). The Mintek-AAC collaboration has been formalized as a joint-venture technology agreement for the comme;cialization, as well as continued development and improvement, of the bacterial oxidation process (MINBAC). From a process standpoint, bacterial oxidation involves the contacting of slurries of finely ground sulphide concentrate with suitable strains of iron-sulphur oxidizing bacteria, which act as the catalyst to promote sulphide·· oxidation by oxygen from air. Process engineering is simplified in that this reaction is carried out at low temperatures and ambient pressures. The view was taken that the successful development and implementation of the MINBAC technology should be based on parallel R&D aimed at an understanding of the process fundamentals, the process engineering and scale-up requirements, as well as the ancillary requirements for the gold recovery-processes and environmental management. This has represented a major R&D effort at a total cost to date of around US $10 million.

Jan 1, 1993

By Sam Rosenblum

The anomaly ratio is obtained by dividing the analyzed value of an element by the anomaly threshold value of the element. The sum of anomaly ratios for all anomalous elements in a sample may be compared with similar sums for other samples, so that the samples having the greatest anomaly-ratio totals can be recognized easily. In partial or full-suites-of-ore-elements the use of anomaly ratios is more meaningful than analyzed values because the ratios quickly indicate anomalous elements and call attention to samples and localities that should be investigated.

Jan 1, 1980

By Peter J. Huck, Bruce G. Stegman, Richard E. Thill

Introduction Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind backfilling process has been successful for stabilizing ground over abandoned and inaccessible underground coal mines. This article describes the systematic evaluation of potential monitoring systems that would improve backfill monitoring technology. It also details field proof-of-concept tests that were conducted on two systems and the difficulties encountered in implementing them. Ground subsidence over abandoned mines can have devastating effects on overlying urban areas decades after the closing of room-and-pillar mines. The result may be cracked foundations, ruptured gas and water lines, broken sewers, distortion or cracking in superstructures, and sinks and potholes in the ground surface. About 32,000 km2 (8 million acres) of land in the US has been undermined for coal. According to the US General Accounting Office, 8,100 km2 (2 million acres) have undergone subsidence and another 8,100 km2 (2 million acres) are expected to subside by the year 2000. Actual figures on land affected or threatened by subsidence are probably much higher, since these estimates were based on late 1960s studies. For more than two decades, the US Bureau of Mines has been engaged in stabilizing ground in urban areas having high risk potential for subsidence costing millions of dollars. Thousands of acres have been stabilized, protecting property worth hundreds of millions of dollars. In earlier years, backfilling was by in-mine stowing in accessible mines or by gravity-feed sluicing methods in inaccessible mines. Pumped-slurry methods have been used extensively in the past 10 years. More slurry can be injected for fill from fewer injection holes over extensive areas in abandoned mines. Since this method requires fewer boreholes, there is less disruption of surface facilities. An investigation was conducted to determine the feasibility of using advanced, remote sensing or monitoring technology for application in monitoring fill placement. Specifically, the objective was to develop conceptual systems for blind backfill monitoring that require fewer boreholes and give better definition than is now possible. Blind Backfilling Methods Blind backfilling operations are conducted from the surface and do not require personnel and equipment underground. These methods are applicable to abandoned, inaccessible workings. Two categories of blind back-filling are point support, practiced by civil engineers to protect individual structures or surface facilities, and areal backfilling methods, used to protect large areas against subsidence. Point Support Methods Point support methods are usually gravity-feed systems. In general, point support methods use small volumes of expensive fill material and require a large number of boreholes within a constructed site. Because of the processed material used for back-filling and the close spacing of the injection boreholes, control and monitoring often may be accomplished by borehole cameras. Areal Backfilling Areal backfilling is conducted mainly by the pumped-slurry injection process (Fig. 1). In eastern and interior coalfields, material used is often mine refuse or flyash, both being undesirable on the surface and costly to dispose of in an environmentally acceptable manner. Hence, the use of

Jan 12, 1983

Sequential and evolutionary changes through time are recognizable in many, perhaps most major families of ore deposits and their geological environments. These changes are additional useful indicators of the evolutionary history of the earth and its tectonic processes. They are important in mineral exploration because they involve consideration of time as a fourth dimension, thereby indicating the most favorable ages, rather than types of rock for investigation. Many of the changes are analogous to those recognized in faunal evolution. Some primitive, unspecialized types of ore deposits occur nearly unchanged through rocks of widely differing age. Others diversify into several, more specialized variants, whereas still others become extinct. The place of these is taken by new, younger types, some of which undergo sudden proliferations and later diversifications of their own. In Archean greenstone belts irrlportant iron, nickel, gold, and base metal deposits occur co-regionally, but in different stratigraphic positions in the same, thick volcano-sedimentary successions. Here their close temporal and spatial associations suggest common genetic exhalative hydrothermal processes. The massive base metal sulfide family of ore deposits provides an excellent example of evolutionary changes, exhibiting distinct variations through both time and space. Deposits belonging to this family span the entire range of time, occurring in rocks of ancient Archean to Recent age, and specific types within the family also span the entire range of spatial environments from ensimatic to ensialic. Moreover there are possible evolutionary metallogenic links between certain types of massive base metal sulfide deposits and other important base metal ores, noteably Mississippi Valley-type and porphyry copper deposits.

Jan 1, 2013

By Thomas N. Walthier

This paper will review world trends that are increasingly restrictive of mineral exploration and mining throughout the Free World This is occurring in the face of projected huge increases in demand for mineral products Some of the impediments are direct and absolute; others are indirect, but nevertheless effective; still others represent merely hostile attitudes Many of the world governments have a reputation for lack of integrity in dealing with existing foreign investments within their borders, and consequently are quite uninviting places for new investments, especially in the capital intensive natural resources industry. Compared with even 35 odd years ago (and pre-World War II is not that long ago) there are few places left where private mining investments are both wanted and where investors are willing, to go. We shall begin with an analysis of conditions in the U. S., shift to neighboring Canada and Flexico, and then have a look around the world. As the world grows smaller for the private mining sector, the function of exploration, development, and operation is passing over to government. We'll conclude with a view of what this holds for the future

Jan 1, 1976

By B. Tolwinski

Long-Term Open Pit Scheduler or L-TOPS is a new software package for evaluating, planning, and design of open pit mines. L-TOPS transforms geological, economic, and technical information about a mineral deposit into a detailed mining schedule that maximizes economic efficiency without neglecting the practical requirements of mining operations. L-TOPS has been customized for integration with Placer Dome Inc.'s existing in-house resource/reserve optimization software to function as a primary tool for property acquisition studies and for the designing of mines for feasibility studies. This pa-per presents an overview of L-TOPS and reports on its application to Placer Pacific's (Placer Dome's Australian affiliate) Mt. Rawdon project.

Jan 1, 1996

By R. N. Chakravorty

Spontaneous combustion presents a very serious hazard to both safety and economics of mining operations. Notwithstanding considerable research that has been done over the years to present and control spontaneous combustion the risk still exists. Consequently, this problem poses a major challenge to mine safety researchers; new and improved techniques are constantly being developed to deal with this major hazard. This paper reviews the current practices to prevent and control spontaneous combustion in coal mine operations highlighting new developments in this area. Research and development work presently being carried out in Canada to' deal with this problem is also discussed which includes monitoring, inertization and application of biotechnology.

Jan 1, 1988

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

Nonfatal injuries from slips, trips, and falls (STF) that occur at surface mines can result from inadequate lighting. Mobile equipment operators are among the occupations associated with the nonfatal incidents reported to the U.S. Mine Safety and Health Administration (MSHA). In addition, getting on/off the equipment (ingress/egress) frequently adds to the highest proportion of nonfatal incidents. Accordingly, researchers at the Pittsburgh Mining Research Division (PMRD), National Institute for Occupational Safety and Health (NIOSH) conducted a field study to investigate lighting on haul trucks and wheel loaderswith regard to glare and illuminance levels recommended by the Illuminating Engineering Society (IES). The objective was to determine whether two light-emitting diode (LED) area luminaires—a Mr. Beams® (model MB390 Ultrabright) (area luminaire-1) and a NIOSH-developed Saturn (custom-designed for a mine roof bolter study) (area luminaire-2)—could complement a headlamp luminaire. Measured levels of visual tasks, with the headlamp alone and the area luminaires plus the headlamp, demonstrated that illuminance met or exceeded IES-recommended levels. Nevertheless, the area luminaires illuminated a much broader area, which is key to increasing hazard awareness. Discomfort and disability glare were lower with area luminaire-1 than with area luminaire-2. Differences in glare were more noticeable for newer models of haul trucks and loaders featuring updated ingress/egress system designs. This study demonstrates that commercially available luminaires, such as area luminaire-1, are capable of complementing headlamp lighting, and can thus improve a miner’s ability to detect and avoid STF hazards.

Jun 17, 2020

By Andrew C. Katen

The mining industry faces increasing geopolitical risk in the coming decades. Constraints such as resource nationalism, corruption and social license could grow to outweigh fundamental limitations like geology or supply and demand (Ernst & Young, 2013; Verrastro et al. 2010). Lurking beneath these more immediate and palpable concerns, however, may be more significant risks entrenched in geography and history. Deep-rooted cultural and strategic forces that emerge slowly ? or erupt suddenly and unexpectedly ? can generate momentous and far-reaching political, social and economic changes. While multinational enterprises routinely assess for political risk, the nature of minerals extraction means long-term and systemic geopolitical conditions are especially important for mining companies to identify and understand. Mine development is a decades-long process that binds companies to the land and makes changing course to avert emerging threats a difficult and costly option. Consequently, geopolitical assessment is a pertinent and valuable tool that mining companies can use to more comprehensively evaluate strategic threats and opportunities. Geopolitics is the study of society, politics and strategy through the lens of geography (Gray, 1996). Its emphasis on relatively permanent physical features of the earth makes geopolitics a uniquely valuable tool for assessing political risk. Topography, climate and natural resources have shaped, constrained and motivated peoples and governments throughout history. These influences transcend regimes, policies and borders ? and even states themselves ? which, by contrast, change often and dramatically. Framing politics against mountains, deserts and rivers supports identification of historical patterns and forecasts of emerging trends. In other words, the physical map provides an objective and consistent model for studying a subjective and dynamic subject such as politics (Sloan and Gray, 1999). Consequently, geopolitical assessment can highlight threats and opportunities that go unaddressed by other risk methodologies that emphasize current conditions (Glancy, 2012). Taken together, the permanence of geography, hindsight afforded by centuries of political history, and interconnectedness of world events makes geopolitical assessment a valuable approach for conceptualizing strategic risk.

Mar 1, 2014

By Ryan Ward

The Missouri River Intake Screen Structure and Tunnel (MRISST) is one phase of the Red River Valley Water Supply Project (RRVWSP), a vital piece of infrastructure in the state of North Dakota to transport water to drought-laden communities in the eastern half of the state. The scope of work consists of constructing a cofferdam in the Missouri River, mining a 1,600-foot by 74-inch tunnel from a secant pile shaft near the riverbank into a cofferdam, and erecting a 40-foot Y-shaped vertical pipe structure in the cofferdam to support the intake screens. Construction personnel worked in the river through the North Dakota winter to construct the cofferdam and contended with high hydrostatic pressures and raveling sands, gravels, cobbles and boulders while mining the tunnel. Diligent planning and meticulous execution were essential to overcoming the challenges encountered below the Missouri River.

Jun 13, 2023

By Jesse L. . Jr. You

Tunnels in the granitic Climax stock at the Nevada Test Site were inspected for keyblock occurrence. Thirteen relatively large pyramidal keyblocks were located in about 230 m (750 it) of tunnel. Orientations, dimensions, joint roughness coefficients, and joint compressive strengths were measured for the faces of nine keyblocks. The measurements were used to back-analyze keyblock stability to check the validity of a numerical model for keyblock behavior. A newly developed three-dimensional numerical model correctly predicted whether or not each keyblock failed in six of eight cases. The two exceptions involved stress conditions and keyblock locations that clearly violated the assumptions that underlie the stability model. The observations also allowed the effect of tunnel orientation on keyblock occurrence to be evaluated. Of the thirteen observed keyblocks, nine large blocks were found in less than 30 m (100 ft) of the Piledriver drift (which runs N56E) while only four blocks of comparable size were observed in 200 m (656 ft) of the Spent Fuel Test--Climax drifts (N61W). The orientations of the keyblock faces were checked against known discontinuity set orientations; some of the faces correlated well with mean set orientations, whi.le other faces were fringe members of sets. Stereographic techniques were used to examine the frequency of keyblock occurrence and to determine the maximum keyblock size that could be encountered with a given combination of discontinuities. Keyblock occurrence was found to be affected by tunnel orientation in a predictable way; this can be used to guide or improve tunnel design practices.

Jan 1, 1986

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By L. Cui

A new flotation collector, benzyl arsonic acid, was used for the flotation of ilmenite. ESCA, Auger spectroscopy, and chemical analysis were used to investigate the correlation between the variation in surface constituents and the flotation recovery of ilmenite. Experiments indicated that, as the ratio of surface Ti ions/surface Fe ions increases, flotation recovery increases. pH regulation with an inorganic acid was found to be effective in changing the ratio of surface ions, and, hence, the flotation recovery.

Jan 1, 1986

By William Bergeson

This paper presents the challenges of the Homestead Avenue Interceptor Extension (HAIE) project in downtown Hartford, Connecticut. The new 72-inch (1,830 mm) sewer pipeline project consists of installing approximately 3,010 linear feet (920 m) of PVC lined reinforced concrete pipe using pressurized face microtunneling. The entire alignment is located within soft to very soft, varved silt and clay. To the extent possible, the alignment was selected to avoid bedrock, glacial till, miscellaneous fill,buried steel piles, and utilities. Challenges for this project include low ground cover, crossing major transportation routes, and limiting settlement to prevent damage to historical buildings and critical utilities. The machine was selected for the ground conditions. Design calculations were performed for selecting the reinforced concrete pipe class and for evaluating settlement. The potential for settlement damage was evaluated using both conventional analysis and finite element analysis

By Jun Ho Lee, Dae Young Kim, Ebrahim Farrokh, Ki Chang Hyun

"The Jinhae Geoje gas pipeline tunnel project is the largest (7.8 km) and the deepest (90 m) subsea tunnel in South Korea. This tunnel will house a pipeline to carry natural gas from the mainland to Geoje Island southeast of the country to alleviate the increased demands for natural gas, especially in the winter season. Tunneling is currently underway using two slurry shield TBMs of 3.5 m diameter. This paper describes the major design elements of the tunneling machines and their performance evaluation. For this purpose, a thorough analysis of geotechnical information was performed to evaluate the tunnel elevation to reduce the risk of tunneling under high water pressure in unstable and permeable rock mass under 9 bar water pressure. TBM specification and TBM performance were also analyzed using different methods, including well-known models as well as a rotary cutting machine test developed in house in Hyundai Engineering and Construction Company. INTRODUCTION High demand for natural gas, especially in winter season was the primary driving factor for the design of the Jinhae Geoje gas pipeline project. This project is located southeast of South Korea between Jinhae district and Geoje Island and runs for over 50 km length. The mid part of this project includes a 3.5 m diameter subsea tunnel consisting of two sections of Geoje to Jiri Island (4.3 km) and Jinhae to Jiri Island (3.5 km). Figure 1 shows the tunnel project location and its layout. Figure 2 shows the geological profile along the tunnel. As can be seen, the tunnel passes mainly through three rock types: granite, tuff breccia, and andesite tuff. This tunnel was planned to be constructed by two face pressurized shielded TBMs and to be lined with a segmental lining of 2.8 m internal diameter. The major challenge for this tunnel is its maximum expected water pressure at the tunnel invert (8.83 bar). At such a high water pressure, the TBMs required special design to ensure they can handle unexpected water pressure and to ensure the risks for the TBM maintenance intervention are minimal. In this regard, a thorough analysis was conducted on the TBM design parameters and geotechnical information to define required TBMs’ design parameters and to identify the safest tunnel elevation. This paper provides a brief overview of the project geotechnical information, TBM selection and its design specification, tunnel elevation selection, and TBM penetration rate evaluation. In this regard, a rotary cutting machine testing equipment was used to perform trial tests on a similar rock type encountered along the tunnel for performance evaluation and optimization."

Jan 1, 2016

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By E. Medina, W. Callupe, R. Sharon

Slope stability in Barrick’s Pierina Mine open pit is significantly influenced by the structural geology, the variably argillized rock mass, and locally by perched groundwater. Development of an extensive surface water diversion network continues at Pierina, which is necessary to minimize highwall and adjacent natural landslide movement and erosion during the wet season. Slope movements are effectively monitored using optical survey methods, strobe light extensometers, gap monitors, and piezometers. The slope stability program at Pierina is focused on improving the understanding of the stability mechanisms in order to ensure continuous safe operating conditions. Priorities are placed on developing an accurate detailed engineering geological model, enhancing groundwater depressurization, and optimizing highwall controlled blasting procedures.

Jan 1, 2003

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By H. S. Duzgun, N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline’s long-term availability, to develop preventive maintenance plans and to make future projections about the dragline’s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, Page 736 and Marion 7820, which have been operating in the Tunçbilek openpit coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data and (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (15.29 m3) seemed to be more reliable and less likely to fail when compared with Marion 7820 (30.58 m3). The operating hours without failure range from 41 to 51 hours with 50% reliability.

Jan 1, 2011

By Elif Emil-Kaya, Bernd Friedrich, Merve Papakci

Samarium (Sm), one of the rare earth elements (REEs), and cobalt (Co) are used in the production of SmCo permanent magnets, which have excellent temperature stability, corrosion resistance and oxidation resistance. Of the two types of SmCo magnets, one contains a high amount of iron, approximately 15.2 percent. This paper focuses on the recycling of iron (Fe)-bearing SmCo. In this study, an oxidative leaching process with nitric acid was developed to eliminate iron through in situ hydrolysis and to dissolve REEs and Co. The influence of experimental conditions on the formation of an amorphous iron compound through the hydrolysis of Fe3+ in a nitric acid environment was thoroughly examined based on a Taguchi orthogonal array. The optimal parameters for oxidative leaching were determined to be an acid concentration of 3 mol/L, a solid-to-liquid ratio of 1/10, and a process temperature of 60 °C.

Jul 1, 2024